Cadillac - CT5 - Owners Manual - 2020 - 2022

Service Bulletin Bulletin No.: 22-NA-094 Date: May, 2022 TECHNICAL Subject: Brand: Loss of Cabin Heat Model: Model Year: from Build Date: to from to Engine: CT4 2020 December 2, 2021 2.0L (LSY) CT5 2020 December 2, 2021 2.0L (LSY) XT4 2019 March 17, 2021 2.0L (LSY) XT5 2020 January 28, 2022 2.0L (LSY) XT6 2020 January 28, 2022 2.0L (LSY) Chevrolet Blazer 2020 2022 January 28, 2022 2.0L (LSY) GMC Acadia 2020 2022 January 28, 2022 2.0L (LSY) Cadillac 2022 SOP Transmission: Involved Region or Country North America Condition Some customers may comment on a loss of cabin heat. Cause The cause of the condition may be a software anomaly in the engine control module (ECM). Correction Reprogram the ECM. Service Procedure Caution: Before downloading the update files, be sure the computer is connected to the internet through a network cable (hardwired). DO NOT DOWNLOAD or install the files wirelessly. If there is an interruption during programming, programming failure or control module damage may occur. • Ensure the programming tool is equipped with the latest software and is securely connected to the data link connector. If there is an interruption during programming, programming failure or control module damage may occur. • Stable battery voltage is critical during programming. Any fluctuation, spiking, over voltage or loss of voltage will interrupt programming. Install a GM Authorized Programming Support Tool to maintain system voltage. Refer to www.gmdesolutions.com for further information. If not available, connect a fully charged 12V jumper or booster pack disconnected from the AC voltage supply. DO NOT connect a battery charger. Copyright 2022 General Motors LLC. All Rights Reserved. • — Follow the on-screen prompts regarding ignition power mode, but ensure that anything that drains excessive power (exterior lights, HVAC blower motor, etc) is off. • Please verify that the radio time and date are set correctly before inserting USB drive into vehicle for programming, otherwise an error will result. • Clear DTCs after programming is complete. Clearing powertrain DTCs will set the Inspection/ Maintenance (I/M) system status indicators to NO. Important: The service technician always needs to verify that the VIN displayed in the TLC left side drop down menu and the top center window match the VIN plate of the vehicle to be programmed prior to using Service Programming System 2 (SPS2) for programming or reprogramming a module. • For the TLC application, service technicians need to always ensure that the power mode (ignition) is “ON” before reading the VIN from the vehicle’s VIN master module and that they do not select a VIN that is already in the TLC application memory from a previous vehicle. Page 2 May, 2022 Bulletin No.: 22-NA-094 • If the VIN that shows up in the TLC top center window after correctly reading the VIN from the vehicle does not match the VIN plate of the vehicle, manually type in the VIN characters from the vehicle VIN plate into the TLC top center window and use these for programming or reprogramming the subject module with the correct vehicle VIN and software and/or calibrations. • The Engine Control Module (ECM) is the master module (for VIP vehicles) that TLC reads to determine the VIN of the vehicle. If the VIN read from the vehicle by TLC does not match the VIN plate of the vehicle, the ECM also needs to be reprogrammed with the correct VIN, software and calibrations that match the vehicle’s VIN plate. • The Body Control Module (BCM) is the master module (for GEM vehicles) that TLC reads to determine the VIN of the vehicle. If the VIN read from the vehicle by TLC does not match the VIN plate of the vehicle, the BCM also needs to be reprogrammed with the correct VIN, software and calibrations that match the vehicle’s VIN plate. Caution: Be sure the VIN selected in the drop down menu (1) is the same as the vehicle connected (2) before beginning programming. 5743643 Bulletin No.: 22-NA-094 May, 2022 Page 3 Important: If the vehicle VIN DOES NOT match, the message below will be shown. 5877000 5644477 Important: Techline Connect screen shown above. Important: If the same calibration/software warning is noted on the TLC Summary screen, select OK and follow screen instructions. After a successful programming event, the WCC is located in the Service Programming System dialogue box of the SPS Summary screen. Document the WCC on the job card. No further action is required. Refer to the Warranty Information section of this bulletin. 1. Reprogram the Engine Control Module. Refer to K20 Engine Control Module: Programming and Setup in the Service Manual. Page 4 May, 2022 Bulletin No.: 22-NA-094 5644478 Note: The screenshot above is an example of module programming and may not be indicative of the specific module that is being programmed. Module selection and VIN information have been blacked out. Important: To avoid warranty transaction rejections, you MUST record the warranty claim code provided on the Warranty Claim Code (WCC) screen shown above on the job card. Refer to callout 1 above for the location of the WCC on the screen. 2. Record the SPS Warranty Claim Code on the job card for warranty transaction submission. Bulletin No.: 22-NA-094 May, 2022 Page 5 Warranty Information Important: Warranty coverage code E2 applies for this module programming event. ECM reprogramming is covered for 8 years/80,000 miles (U.S.) or 8 years/ 130,000 km (Canada). For vehicles repaired under the Emission coverage, use the following labor operation. Reference the Applicable Warranties section of Investigate Vehicle History (IVH) for coverage information: Labor Operation 2888658* Description Labor Time Engine Control Module Reprogramming for Loss of Cabin Heat 0.3 hr *This is a unique Labor Operation for bulletin use only. Important: To avoid warranty transaction rejections, carefully read and follow the instructions below: • The Warranty Claim Code must be accurately entered in the “SPS Warranty Claim Code” field of the transaction. • When more than one Warranty Claim Code is generated for a programming event, it is required to document all Warranty Claim Codes in the “Correction” field on the job card. Dealers must also enter one of the codes in the “SPS Warranty Claim Code” field of the transaction, otherwise the transaction will reject. It is best practice to enter the FINAL code provided by SPS/SPS2. Warranty Claim Code Information Retrieval If the Warranty Claim Code was not recorded on the Job Card, the code can be retrieved in the SPS2 system as follows: 1. Open TLC on the computer used to program the vehicle. 2. Select and start SPS2. 3. Select Settings. 4. Select the Warranty Claim Code tab. The VIN, Warranty Claim Code and Date/Time will be listed on a roster of recent programming events. If the code is retrievable, dealers should resubmit the transaction making sure to include the code in the SPS Warranty Claim Code field. Version 1 Modified Released May 13, 2022 GM bulletins are intended for use by professional technicians, NOT a "do-it-yourselfer". They are written to inform these technicians of conditions that may occur on some vehicles, or to provide information that could assist in the proper service of a vehicle. Properly trained technicians have the equipment, tools, safety instructions, and know-how to do a job properly and safely. If a condition is described, DO NOT assume that the bulletin applies to your vehicle, or that your vehicle will have that condition. See your GM dealer for information on whether your vehicle may benefit from the information. WE SUPPORT VOLUNTARY TECHNICIAN CERTIFICATION