Nissan - Titan - Workshop Manual - 2004 - 2015 (2)

LIFT CORPORATION Sht. 1 of 18 DSG# M-14-33 Rev. A Date: 05/31/2017 INSTRUCTIONS, NISSAN TITAN TRUCK INSTALLATION KIT (C2 PICKUP LIFTGATES) NISSAN TITAN PICKUP TRUCKS, 2004 - 2015 KIT P/N 295040-01 MOUNTING BRACKET, LH P/N 295039-01 QTY. 1 MAIN FRAME MOUNTING BRACKET P/N 289637-01 QTY. 2 MOUNTING BRACKET, RH P/N 295039-02 QTY. 1 BACKPLATE P/N 289453-01 QTY. 2 LIFT CORPORATION Sht. 2 of 18 DSG# M-14-33 Rev. A Date: 05/31/2017 BOLT KIT, P/N 289488-01 BUTTONHEAD SCREW 3/8”- 16 X 1” LG. P/N 900064-05 QTY. 8 LOCK WASHER, 3/8” P/N 902011-4 QTY. 20 FLAT WASHER, 3/8” P/N 902001-2 QTY. 6 HEX NUT, 3/8”-16 P/N 903161-05 QTY. 20 PAN HEAD SCREW #10-24 X 3/4” LG. P/N 900753-07 QTY. 8 HEX CAP SCREW 3/16”-16 X 1” LG, GR5 P/N 900778-02 QTY. 12 LOCK WASHER, 1/2” P/N 902011-6 QTY. 6 HEX CAP SCREW 1/2”- 13 X 1-1/4” LG, GR5 P/N 900781-02 QTY. 6 FLAT WASHER, 1-3/8” OD, 1/2” P/N 902014 QTY. 4 LOCK NUT, 1/2”-13 P/N 040066 QTY. 4 LIFT CORPORATION Sht. 3 of 18 DSG# M-14-33 Rev. A Date: 05/31/2017 NOTE: C2 Liftgates are shipped with the following parts kits for installing the Liftgate. The parts are stored in the main frame housing. C2 LIFTGATE SMALL PARTS & MANUAL KIT P/N 289484-01 LICENSE PLATE LIGHT INSTALLATION M-14-35 CIRCUIT BREAKER, 150 AMP P/N 907207-01 QTY. 1 LUG, 4GA COPPER, 3/8” P/N 907278-01 QTY. 4 PADLOCK (2 KEYS) P/N 908221-01 QTY. 1 C2 OPERATION MANUAL M-14-36 LICENSE PLATE LIGHT P/N 907210-01 QTY. 1 NYLON PLUG, 1/2” P/N 908081-01 QTY. 5 BUTT CONNECTOR, 14-16 AWG P/N 030491 QTY. 2 BREATHER PLUG, 3/8” NPT P/N 295049 QTY. 1 SELF-TAPPING SCREW, 1/4”-20 X 5/8” LG. P/N 900705-02 QTY. 2 GROMMET NUT, 1/4” P/N 901015-03 QTY. 2 PAN HEAD SCREW, #10-24 X 3/4” LG. P/N 900007-6 QTY. 2 NUT, #10-24 P/N 903163-02 QTY. 2 LOWER MOUNTING ANGLE SHIPPING LEG P/N 289543-02 QTY. 2 DROP-AWAY PIN P/N 289483-01 QTY. 1 LOCK NUT, 3/8”-16 P/N 901016-4 QTY. 1 LIFT CORPORATION Sht. 4 of 18 DSG# M-14-33 Rev. A Date: 05/31/2017 NOTE: Installer is responsible for ensuring vehicle meets Federal, State, and Local standards and regulations. BODY STRENGTH ! WARNING Consult vehicle body manufacturer for vehicle body strength data. Make sure the forces created by the Liftgate are within the limits prescribed by the vehicle body manufacturer. NOTE: Maximum operating bed height for C2 mounted on pickup body is 42” (Unloaded). Minimum bed height is 28” (Loaded). The C2 is a body-mounted liftgate that put forces on the side walls of truck bodies (FIG. 4-1). For correct installation, truck bodies must be strong enough to withstand the tension, compression and shear forces shown in FIG. 4-1. X= Tension on each sidewall Y= Compression on each sidewall Z= Shear on each sidewall X= 2600 LB Z= 2000 LB Y= 2600 LB BED HEIGHT C2 LIFTGATE SHOWN ON TRUCK BODY FIG. 4-1 LIFT CORPORATION Sht. 5 of 18 DSG# M-14-33 Rev. A Date: 05/31/2017 PREPARING LIFTGATE 1. Remove mounting kits shipped with liftgate. Refer to Sheets 1, 2 and 3. Verify mounting brackets are the correct brackets for this installation. ` ! CAUTION Liftgate will not stand upright without the shipping angles. Before removing the angles, make sure Liftgate is supported with forklift or pallet jack. Injury & property damage could result if Liftgate falls over. 2. Support Liftgate on shipping pallet with forklift or pallet jack. Then, unbolt shipping angle from each column on the Liftgate (FIG. 5-1). Save shipping angles to use for lower mounting brackets. 3/8”-16 BOLT, 3/8” LOCK WASHER, 3/8”-16 NUT (4 PLACES) SPACER (2 PLACES) ANGLE (2 PLACES) RH COLUMN LH COLUMN REMOVING SHIPPING ANGLES BOLTED TO COLUMNS OF C2 LIFTGATE FIG. 5-1 LIFT CORPORATION Sht. 6 of 18 DSG# M-14-33 Rev. A Date: 05/31/2017 BOLTING ON MAIN FRAME BRACKETS NOTE: The extra hole in the main frame mounting brackets is always below the 1/4” X 1” strip. Bolt main frame mounting brackets (Kit items) to column flats (FIGS. 6-1 and 6-2). COLUMN FLAT (2 PLACES) MAIN FRAME MOUNTING BRACKET (2 PLACES) COLUMN (2 PLACES) C2 LIFTGATE SHOWN WITH BOLT-ON MAIN FRAME BRACKETS FIG. 6-1 MAIN FRAME MOUNTING BRACKET (2 PLACES) 59.94” COLUMN FLAT (2 PLACES) 3/8” X 1” BUTTON HEAD BOLT (8 PLACES) 3/8” LOCK WASHER (8 PLACES) 3/8” NUT (8 PLACES) BOLTING MAIN FRAME MOUNTING BRACKETS TO COLUMNS ON C2 LIFTGATE (TOP VIEW) FIG. 6-2 LIFT CORPORATION Sht. 7 of 18 DSG# M-14-33 Rev. A Date: 05/31/2017 PREPARING PICKUP TRUCK 1. Unbolt the tailgate, supports, strikers and fasteners (FIG. 7-1). 2. Support rear bumper and trailer hitch (if equipped) (FIG. 7-2) before unbolting bumper brackets and hitch (if equipped). NOTE: When liftgate is installed on the truck the tailgate, trailer hitch (if equipped), rear bumper, and bumper brackets cannot be reinstalled. RUBBER PAD (REF) TAILGATE STRIKER TAILGATE (2 PLACES) HINGE (REF) SUPPORT (2 PLACES) TAILGATE REMOVING TAILGATE & SUPPORTS FIG. 7-1 BUMPER MOUNTING BRACKETS 3. Unbolt and remove rear bumper and bumper brackets (FIG. 7-2). TRAILER HITCH REAR BUMPER REMOVING REAR BUMPER FIG. 7-2 LIFT CORPORATION Sht. 8 of 18 DSG# M-14-33 Rev. A Date: 05/31/2017 INSTALLING LIFTGATE NOTE: Holes for mounting brackets are marked and drilled only after liftgate is in correct position on the pickup bed. NOTE: To avoid interference, install aftermarket hitch receiver before liftgate. 1. Position the LH and RH mounting brackets (Kit items) in the pickup bed just forward of corner posts (FIG. 8-1). RH MOUNTING BRACKET 2. Position liftgate in the rear opening of the pickup bed (FIG. 8-1). • Liftgate centered on rear opening in pickup bed • Columns vertical • Spare tire access hole aligned with MAIN FRAME spare tire tube on truck LH BRACKET • Top of main frame flush with floor of pickup bed CORNER POST 3/8”-16 X 1” LG BOLT 3/8” LOCK WASHER 3/8”-16 NUT (3 PLACES) MAIN FRAME RH BRACKET LIFTGATE NOTE: Ensure nuts and lock washers are on the inboard side of the mounting brackets. 3. Bolt the main frame brackets on liftgate, to the RH mounting brackets as shown in FIG. 8-1. Handtighten bolts and nuts. Repeat for LH mounting bracket. 4. Allow the Liftgate to hang supported by the corner posts. BOLTING LIFTGATE TO RH MOUNTING BRACKET FIG. 8-1 LIFT CORPORATION Sht. 9 of 18 DSG# M-14-33 Rev. A Date: 05/31/2017 INSTALLING LIFTGATE - Continued CAUTION Before drilling holes in the pickup bed, ensure there are no obstructions or items that could be damaged. 5. Hold RH mounting bracket against corner post of the pickup bed (FIG. 9-1). Then, use 2 of the 4 bracket holes that are not obstructed, to drill 2 holes for 3/8”-16 bolts in floor of the pickup bed (FIG. 9-1). Repeat for LH mounting bracket. 6. Bolt RH mounting bracket to the floor of pickup bed as shown in FIG. 9-1. Repeat for LH mounting bracket. CORNER POST 3/8”-16 HEX BOLT (2 PLACES) TEMPLATE HOLES TO DRILL 2 HOLES IN PICKUP BED BACKPLATE 7. Unlatch and unfold platform. Refer to C2 Operation Manual if needed. Then, adjust liftgate position so platform is level from front to back. 8. Securely tighten 3 bolts fastening RH mounting bracket to main frame bracket (FIG. 9-1). Ensure the split lock washers are not in the slotted holes on main frame bracket. Repeat for LH mounting bracket. 3/8” LOCK WASHER (2 PLACES) 3/8” HEX NUT (2 PLACES) FLOOR OF PICKUP BED BOLTING RH MOUNTING BRACKET TO PICKUP BED (LIFTGATE NOT SHOWN) FIG. 9-1 LIFT CORPORATION Sht. 10 of 18 DSG# M-14-33 Rev. A Date: 05/31/2017 CHECKING ACCESS TO SPARE TIRE CAUTION Do not use a battery charger for connecting power to Liftgate power cables. 1. Connect power from a 12 volt truck battery to the Liftgate power cables extending from the back of main frame housing. 2. Refer to operating instructions, in C2 Operation Manual, to unfold platform and activate the Liftgate. NOTE: With the POWER ON and LIFTGATE ACTIVATED lights on, the Liftgate can be raised or lowered. If the Liftgate is not used for 90 seconds, the control will automatically deactivate. 3. Use the control switch to lower (DN) the platform to the ground (FIG. 10-1). USING CONTROL SWITCH TO LOWER LIFTGATE FIG. 10-1 5/16” HEX NUT, 5/16” FLAT WASHERS (3 PLACES) 4. Unbolt and remove cover from main frame housing (FIG. 10-2). COVER REMOVING HOUSING COVER FROM C2 LIFTGATE FIG. 10-2 LIFT CORPORATION Sht. 11 of 18 DSG# M-14-33 Rev. A Date: 05/31/2017 CHECKING ACCESS TO SPARE TIRE - Continued 5. Remove the correct black plastic plugs from the cover and main frame (FIG. 11-1). LH COLUMN (DRIVER SIDE) REAR OF LIFTGATE 2” ROUND HOLE OR 3/4” X 1-3/4” LG. SLOT 2-3/4” 6. Insert the spare tire crank handle through the holes in the liftgate main frame. 7. Ensure spare tire can be accessed using the crank handle. REAR ACCESS HOLE FOR TITAN, 2004-2015 (REAR OF LIFTGATE) 24-3/8” REMOVING PLASTIC PLUGS FOR SPARE TIRE ACCESS, NISSAN TITAN, 2004-2015 FIG. 11-1 LIFT CORPORATION Sht. 12 of 18 DSG# M-14-33 Rev. A Date: 05/31/2017 ROUTING POWER CABLES 1. Remove the small parts and manual kit from the housing. Refer to Sheet 3 for contents of the kits. 2. Install circuit breaker (FIG. 12-1) inside the engine compartment near truck battery (+) terminal and away from moving parts. Allow enough room for power cables to be run and for easy access to circuit breaker. 150A CIRCUIT BREAKER BATTERY (-) CABLE MAIN FRAME HOUSING (+) CABLE RUNNING POWER CABLES FROM LIFTGATE TO BATTERY FIG. 12-1 3. Pull the (+) and (-) power cables through the cord grip on back of main frame housing. Leave about 2” of slack, for power cables, inside main frame housing. 4. Route power cables along truck frame to truck battery (FIG. 12-1). Pull extra cable beyond the battery terminals. Then, separate positive (+) cable from negative (-) cable. 5. Cut positive (+) cable to the length required to reach the AUX terminal of the circuit breaker (FIG. 12-1), without putting strain on the connection. Install copper lug (Kit item) (FIGS. 12-2 and 12-3). Then, connect to AUX terminal on 150A circuit breaker. COPPER LUG HEATSHRINK TUBING POWER CABLE (BARE WIRE END) PLACING COPPER LUG & HEATSHRINK TUBING ON POWER CABLE FIG. 12-2 6. Cut remaining positive (+) cable long enough to reach from the circuit breaker BAT terminal to the positive (+) battery terminal (FIG. 12-1) without putting strain on the connection. Install copper lugs (Kit item) on both ends of cable (FIGS. 12-2 and 12-3). Then, connect cable to BAT terminal on 150A circuit breaker and positive (+) terminal on battery. TYPICAL POWER CABLE WITH COPPER LUG INSTALLED FIG. 12-3 7. Cut negative (-) cable to length required to reach negative (-) battery terminal without putting strain on the connection. Install copper lug (Kit item) (FIGS. 12-2 and 12-3). Then, connect cable to negative (-) terminal on battery. LIFT CORPORATION Sht. 13 of 18 DSG# M-14-33 Rev. A Date: 05/31/2017 C2 PICKUP LIFTGATE HYDRAULIC & ELECTRICAL SYSTEMS DIAGRAM FIG. 13-1 LIFT CORPORATION Sht. 14 of 18 DSG# M-14-33 Rev. A Date: 05/31/2017 INSTALL LOWER MOUNTS CAUTION Liftgate can be severely damaged by connecting electric welder to liftgate at the wrong place. To prevent damage, always connect ground lead directly to component being welded & as close as possible to weld. NOTE: Lower mounts are essential for Liftgate to be installed correctly. They attach to the truck frame and support the bottom of Liftgate. 3/8” HEX NUT (2 PLACES) 1. Unbolt bracket plates from bottom of main frame housing (FIG. 14-1). BRACKET PLATE (2 PLACES) 2. Position 2 bolt-on mounting angles, nearest to truck frame at bottom of Liftgate main frame housing (FIG. 14-2). Then bolt each angle to hole allowing closest fit to truck frame. 3. Position 2 bracket plates (Kit items) on truck frame at bottom of Liftgate main frame housing (FIG. 14-2). Bolt to truck frame. If necessary, modify bracket plates for best fit. 4. Clamp 2 short angles (no holes) (Kit items) to bracket plates on truck frame (FIG. 14-2). Position the 2 angles to reach the angles bolted on bottom of main frame housing. 5. With angles, and bracket plates positioned and clamped together, tack weld the angles and plates in position (FIG. 14-2). 3/8” FLAT WASHER (2 PLACES) 3/8”-16 BOLT, (2 PLACES) MAIN FRAME HOUSING REMOVING BRACKET PLATES FROM MAIN FRAME HOUSING (C2 SHOWN) FIG. 14-1 BOLT-ON BRACKET PLATE (2 PLACES) MOUNTING ANGLE (2 PLACES) MOUNTING ANGLE (2 PLACES) 6. Unbolt tack-welded lower brackets from truck frame (FIG. 14-2). Then, finish weld the bracket plates and angles. 1/2”-13 BOLT, 1/2” LOCK WASHER (2 PLACES) 7. Bolt the finish-welded bracket plates and angles back in position on the bottom of the main frame housing and truck frame (FIG. 14-2). FABRICATING LOWER BRACKETS TO SUPPORT LIFTGATE (C2 SHOWN) FIG. 14-2 LIFT CORPORATION Sht. 15 of 18 DSG# M-14-33 Rev. A Date: 05/31/2017 COMPLETE LIFTGATE INSTALLATION CAUTION BREATHER PLUG Hydraulic system is filled at the factory with correct amount of oil. It is unnecessary to add more oil except as required for periodic maintenance of the liftgate. 1. Remove the solid plug from the pump reservoir (FIG. 15-1). Install breather plug (Kit item) in pump reservoir. PUMP & MOTOR RESERVOIR 2. Bolt on main frame cover (FIG. 15-2). 3. Install the two square plastic grommet nuts (Kit item), for the license plate, into the square holes on the Liftgate main frame cover (FIG. 15-2). INSTALLING VENT PLUG ON PUMP RESERVOIR FIG. 15-1 5/16” HEX NUT, 5/16” FLAT WASHERS (3 PLACES) 4. Install the license plate using two 1/4”-20 self-tapping screws (Kit item) (FIG. 15-2). COVER 5. Install the license plate lights into the holes provided. Refer to instruction sheet M-14-35. Then, connect the license plate lights to the vehicle’s wiring. GROMMET NUT (2 PLACES) SELF-TAPPING SCREW (2 PLACES) LICENSE PLATE (REF) INSTALLING COVER & LICENSE PLATE (C2 LIFTGATE SHOWN) FIG. 15-2 LIFT CORPORATION Sht. 16 of 18 DSG# M-14-33 Rev. A Date: 05/31/2017 COMPLETE LIFTGATE INSTALLATION - Continued 6. To use the drop-away platform feature, install drop pin and 3/8”-16 lock nut (Kit items) on the bottom of RH column (FIG. 16-1). Tighten lock nut securely. DROP PIN 3/8”-16 LOCK NUT (P/N 901016-4) RH COLUMN INSTALLING DROP PIN ON RH COLUMN (C2 LIFTGATE SHOWN) FIG. 16-1 7. Install the 3/8” round plastic plugs into the empty holes in the bottom of the columns. 8. If previously removed, reinstall spare tire. LIFT CORPORATION Sht. 17 of 18 DSG# M-14-33 Rev. A Date: 05/31/2017 TEST OPERATION OF LIFTGATE ! WARNING Keep all foreign objects out of the Liftgate mainframe and away from pinch points at all times when operating Liftgate. NOTE: The LIFTGATE ACTIVATED LED illuminates when Liftgate power is on. Control switch should deactivate after 90 seconds of not being used. 1. Check operation of control switch for proper operation by pressing POWER ON button once to activate. Next, press POWER ON button again to deactivate Liftgate power. Then, press the POWER ON button twice to reset low voltage (FIG. 17-1). POWER ON SWITCH LIFTGATE ACTIVATED SWITCH 2. Press the LIFTGATE ACTIVATED switch within 1 second to activate the timer (FIG. 17-1). 3. Raise (UP) and lower (DN) the unloaded platform (FIGS. 17-1 and 17-2) on a flat surface. Check for proper operating speed and alignment with the ground. CHECKING OPERATION OF CONTROL SWITCH AND RAISING PLATFORM FIG. 17-1 4. Load the platform with the rated capacity and measure the time to RAISE the platform (FIG. 17-1). The platform should raise approximately 2” to 3” per second. 5. Examine the platform for any downward creep. 6. Measure the time to LOWER the platform still loaded (FIG. 17-2). The load should descend approximately 7” to 9” per second. 7. Remove the load from the platform and examine the Liftgate and vehicle for hydraulic oil leaks, loose wiring, and any other problems. 8. Reinstall the main frame housing cover. Then, close and latch platform. USING CONTROL SWITCH TO LOWER PLATFORM FIG. 17-2 LIFT CORPORATION Sht. 18 of 18 DSG# M-14-33 Rev. A Date: 05/31/2017 TEST OPERATION OF LIFTGATE - Continued 9. Lock the latch on LH side or RH side through the hole in the latch pin (FIG. 18-1). LATCH LATCH PIN LOCK LOCKING PLATFORM (C2 LIFTGATE) FIG. 18-1