Installation Instructions
Precision Sport Shifter
NISSAN SILVIA S13, PS13, S14
1988-1999 NISSAN 180SX (NON-US)
1988-1999 NISSAN 200SX (NON-US)
NISSAN SKYLINE R31, R32, R33 (RB20, NON-TURBO)
1989-1998 NISSAN 240SX KA24/SR20/RB20 (US ONLY )
Part Number 45088
©2004, 2003, 2001 by B&M Racing and Performance Products
(see www.bmracing.com for the latest vehicle fitment applications and model years)
This B&M Precision Sport Shifter has been designed to work on most models listed above equipped with a manual
transmission. It has been engineered to greatly reduce shift throw and improve shifter feel. Check the parts list and tool
lists at the beginning of these instructions for the supplied parts and the tools required to install your B&M Precision Sport
Shifter. Installation of the B&M Precision Sport Shifter can be accomplished by anyone with minimal mechanical
experience.
INTRODUCTION
The B&M Precision Sport Shifter can be installed in less than an hour by carefully following the instructions. Read all
instructions first to familiarize yourself with the parts, tools, and procedures. This kit contains all the parts necessary to
install the shifter.
PARTS
B&M Precision
Sport Shifter
Printed in the U.S.A.
9500728-02
TOOLS
DRIVE
EXTENSION
10MM AND 12MM SOCKET
SCREWDRIVER (PHILLIPS)
DISASSEMBLY
STEP 1. Remove stock shift knob.
STEP 2. Remove shift boot.
12MM OPEN-ENDED WRENCH
STEP 3. Remove two (2) front center console screws.
Tool: Screwdriver (phillips)
SCREWS
STEP 4. Remove two (2) center console screws located in
storage unit.
Tool: Screwdriver (phillips)
SCREWS
STEP 5. Remove power window wire harness.
NOTE: Push tab to remove from center console.
CENTER CONSOLE
TAB
STEP 6. Remove center console.
WIRE HARNESS
STEP 7. Remove bolts securing rubber protective boot.
Tools: Drive, extension, and 10mm socket
STEP 8. Remove steel retaining ring.
STEP 9. Remove rubber protective boot.
STEP 10. Remove six (6) bolts that secure shifter to transmission.
Tools: Drive, extension, 12mm socket, and 12mm
open-ended wrench
NOTE: Two front bolts are accessed from under the
vehicle. Car must be lifted and properly
supported to access bolts with open-ended
wrench.
STEP 11. Remove stock shifter.
ASSEMBLY
STEP 12. Install B&M Precision Sport Shifter.
Part: B&M Precision Sport Shifter
NOTES: Make sure shifter engages mechanism in
transmission.
Reuse stock gasket. If gasket is damaged,
apply RTV silicone to perimeter of base.
STEP 13. Install six (6) bolts that secure shifter to transmission.
Tools: Drive, extension,12mm socket, and 12mm openended wrench
NOTE: Two front bolts are accessed from under the
vehicle. Car must be lifted and properly supported
to access bolts with open-ended wrench.
STEP 14. Install rubber protective boot.
GASKET
STEP 15. Install steel retaining ring.
STEP 16. Install four (4) bolts securing rubber protective boot.
Tools: Drive, extension, and 10mm socket.
STEP 17. Install power window wire harness.
CENTER CONSOLE
TAB
STEP 18. Install center console.
WIRE HARNESS
STEP 19. Install two (2) front center console screws.
Tools: Screwdriver (phillips)
SCREWS
STEP 20. Install two (2) center console screws located in storage
unit.
Tools: Screwdriver (phillips)
SCREWS
STEP 21. Install shift boot.
STEP 22 Re-install stock knob. Test movement through each
gear to ensure shifter engages safely into each gear.
ENJOY!