Lotus - Exige S2 - Workshop Manual - (2003)

REVERIE LIMITED Tel: 01206 866663 Unit 2, Chandlers Row 02081 235997 Colchester E-mail: [email protected] Essex, CO1 2HG Skype: Reverie_Composites Elise/Exige S1/S2 Centre Console Fitting Guide R01SU0192, R01SU0140 Introduction The Carbon Fibre centre console is designed to replace the existing OEM console and offer significant weight savings. The centre console is secured in place using 3 x M5 bolts. Parts Available: R01SU0140 Lotus Elise/Exige S1 Carbon Fibre Centre Tunnel - RHD 340R STYLE R01SU0192 Lotus Elise/Exige S1 Carbon Fibre Centre Tunnel - LHD 340R STYLE LOTUS DISCLAIMER Although REVERIE LIMITED supply parts for use with/on vehicles manufactured by Lotus Cars Limited, REVERIE LIMITED is in no way connected to Lotus Cars Limited or any other member of the Lotus Group of companies (“Lotus”) and is entirely independent of Lotus. Accordingly, none of the products offered for sale or supplied by REVERIE LIMITED (nor any advice or service offered or provided by REVERIE LIMITED) are in any way endorsed by Lotus and Lotus has not tested or approved any such products or services. Accordingly, Lotus shall not under any circumstances be liable for any loss, claim, damages or any consequential, indirect or special damages whatsoever arising out of or in connection with the use of products sold or supplied by ReVerie. Tools Required 8mm spanner Metric Allen key set Parts supplied R01SW6111 R01SW6247 C01SW6005 M5 x 20mm BUTTON SOCKET S/STEEL SCREW M5 LOTUS BODY FIXING WASHER M5 U-NUT QTY: 3 QTY: 3 QTY: 2 1. This is for using a 340R cover in an Exige / Elise S1/S2 K series. The Slot at the front of the part moved position if LHD www.reverie.ltd.uk Page 1/3 or RHD, RHD cut-out shown below (Larger amount of carbon to RHS). 27.5mm OD cigarette lighter hole required in front, just one not two as shown left. www.reverie.ltd.uk 2. Make slotted bracket as shown with M5 Rivsert fitted. Steel slotted and drilled Strip Bracket material can be sourced on-line or motorists supply stores. 3. Make angled bracket as shown in 2 images left and supply M5 deep threaded U-Nut. 4. Supply Deep threaded U-nut m5 (C01SW6005) for this other side. Page 2/3 5. Handbrake Trim hole does not change position for LHD or RHD, Note small cable slot at rear also. Secure console in place. WARNING: MOTORSPORT OR DRIVING CAN BE DANGEROUS RESULTING IN DEATH OR PERSONAL INJURY. READ OUR FITTING INSTRUCTIONS CAREFULLY This article is sold without warranty expressed or implied. No warranty or representation is made as to this product’s ability to protect the user from injury or death. The user assumes that risk. The effectiveness, warranty and longevity of this equipment are directly related to the manner in which it is INSTALLED, USED, and/or MAINTAINED. THE USER ASSUMES THE RISK. Fitment of REVERIE PRODUCTS TO AUTOMOBILES THAT ARE SUBJECT TO A MANUFACTURER'S WARRANTY MAY VOID THE MANUFACTURER'S WARRANTY AND THE VEHICLES ABILITY TO MEET EMISSION OR OTHER TRANSPORT REGULATIONS. By purchasing this product and opening the packaging, purchasers expressly acknowledge, understand and agree that they take , select and purchase these REVERIE products from REVERIE, its affiliates, distributors, and agents ( collectively, REVERIE) "as is" and "with all faults". The entire risk as to the quality and performance of these REVERIE parts is with the purchasers. Should the goods prove defective following their purchase; the purchasers assume the entire cost for all necessary servicing or repair or any resulting liability. Working on your car can be a dangerous activity. If you are unsure of what you are doing, please leave mechanical or Safety critical work to a skilled mechanic. We take no responsibility for the incorrect use and / or installation of REVERIE products. WWW.REVERIE.LTD.UK UV-PROTECTION Please Note Epoxy Pre-preg products are not UV stable. Texallium products are particularly liable and can yellow in only 2 – 6 weeks. The epoxy resin will ‘yellow’ with prolonged exposure to UV radiation and material strength properties will slowly deteriorate. We recommend exterior products or those exposed to constant UV are either regularly treated with UV polish or screens such as Armour-all or 606 protect ant or colour painted or at least Lacquered. We use predominately 2K car lacquers of medium solids, the DBS range has been found very suitable, although people have had equally good results with Urethanes varnishes and epoxy clear coats. The surface should be sanded with 180, 240 then 320 grit and a cleaning solvent used to remove grease or dirt prior to paint application. Several coats may be required (normally 3 to 4 light coats) to avoid pin-holing, common with painting composite products. Pin holes may be dubbed in carefully with a brush, then wet flatted for a final application of 3 thin coats. Let air dry only, you may stove the paint at 70’c once fully air dried. www.reverie.ltd.uk Page 3/3