Lexus - RX 450 - Workshop Manual - 2017 - 2017 (2)

Platform: DBALL2 Firmware: TL8 Remote Start Ready (RSR) Installation Rev.: 20170824 Update Alert: Firmware updates are posted on the web on a regular basis. We recommend that you check for firmware and/or install guide updates prior to installing this product. Installation Guide The TL8 firmware for DBALL2 is an all-in-one door lock and override module compatible with specific Lexus and Toyota vehicles. This guide supports the installation of a DBALL2 in Remote Start Ready (RSR) mode. This solution offers three (3) configuration options to control your system: 3x OEM Lock Remote Start Activation, RF System or SmartStart (all sold separately). This module can only be flashed and configured using XpressVIP at www.directechs.com or using the Directechs Mobile application for smartphones. Refer to the Module Programming section for more information. Remote Start Ready (RSR) is a function that enables the interface module to remote start the vehicle completely on its own. Consequently, there is no need for an aftermarket or an OEM remote starter in order to start the vehicle from a distance. IMPORTANT: - No takeover feature is available. The vehicle will shut down as soon as a door is opened. - To remote start the engine, the hood, hatch, and all doors must be closed. Index Vehicle Application Guide................................................................................................................................................... 02 OEM Remote Starter Detection......................................................................................................................................... 03 Installation (Wiring Diagram & Vehicle Wiring Reference Chart) Type 1................................................................................................................................................................................. Type 2................................................................................................................................................................................. Type 3................................................................................................................................................................................. Type 4................................................................................................................................................................................. Type 5................................................................................................................................................................................. Type 6................................................................................................................................................................................. SmartStart/XL202 Installation Notes.................................................................................................................................. 05 09 12 15 18 21 24 Programming Module Programming......................................................................................................................................................... Module Reset & Hard Reset............................................................................................................................................... Feature & Option List......................................................................................................................................................... Feature Programming........................................................................................................................................................ 25 26 27 27 LED Diagnostics & Troubleshooting.................................................................................................................................. 28 Parking Light Error Codes.................................................................................................................................................. 30 Limited One-Year Consumer Warranty............................................................................................................................... 31 Quick Reference Guide...................................................................................................................................................... 32 SmartStart Compatible SmartStart is equipped with D2D, which means it can be connected to an interface module and used in Remote Start Ready (RSR) mode without the use of a remote starter. See the Module Programming section for more information. ® Toyota and Lexus are registered trademarks and property of their respective companies. © 2017 Directed. All rights reserved. Platform: DBALL2 Firmware: TL8 Remote Start Ready (RSR) Installation Rev.: 20170824 Page 2 Vehicle Application Guide DL-Disarm Factory Security DL-Door Lock Control DL-Door Unlock DL-Driver Priority Unlock RS-3x LOCK START (Start control using OEM Remote) RS-3x LOCK STOP (Stop control using OEM Remote) RS-RAP Shut Down (Retained ACC Power) RS-Remote Start Ready RS-SmartStart RS-Tach / RPM Output SS-Entry Monitoring ALL Door Pins SS-Entry Monitoring Hood Pin SS-Entry Monitoring Trunk/Hatch Pin SS-Factory Alarm Trigger Monitoring ST-Brake Status (foot brake) ST-Ignition Status 1 DL-Arm Factory Security 1 AV-Parking Lights Control 1 2014 2016 6 2015 2017 Vehicles PK-Immobilizer Bypass-Data No Key Req'd The table below lists the vehicles and features which are compatible with this product. Refer to the following pages for more information on installation wiring, programming and troubleshooting for these vehicles. • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • Lexus IS 200t (Smart Key) IS 250 (Smart Key) IS 300 (Smart Key) 6 1 IS 350 (Smart Key) 6 1 1 NX 200t (Smart Key) 2 2 2 • • • • • • • • • • • • • • • • • • • NX 300h (Smart Key) 2 2 2 • • • • • • • • • • • • • • • • • • • 1 1 • • • • • • • • • • • • • • • • • • • 1 • • • • • • • • • • • • • • • • • • • RC 350 (Smart Key) RC F (Smart Key) 1 RX 350 (Smart Key) 4 4 • • • • • • • • • • • • • • • • • • • RX 450h (Smart Key) 4 4 • • • • • • • • • • • • • • • • • • • Highlander (Smart Key) 5 3 3 3 • • • • • • • • • • • • • • • • • • • Highlander Hybrid 5 3 3 3 • • • • • • • • • • • • • • • • • • • Tacoma (Smart Key) 3 3 • • • • • • • • • • • • • • • • • • • Toyota Legend: AV: Horn & Lights Control RS: Remote Start & Engine Controls DL: OE Door Lock & Alarm Controls SS: Integrated Security & Monitoring FOB: Sync CAN Interface w/FOB Remote ST: Function/Feature Status PK: Transponder & Immobilizer Override © 2017 Directed. All rights reserved. Platform: DBALL2 Firmware: TL8 Remote Start Ready (RSR) Installation Rev.: 20170824 Page 3 How to Know if the Vehicle is Equipped with an OEM Remote Starter 1- An “ENGINE STARTER” sticker should be on the remote. 2- Remote start the OEM remote starter: Press the remote control’s lock button twice within 2 seconds, then press and hold the lock button for 3 seconds. The parking lights flash after 3 seconds. The engine starts and the parking lights flash repeatedly for 20 seconds. x2 & ENGINE STARTER Press & Hold for 3 seconds Important OEM Remote Starter Information Ÿ If the vehicle is equipped with a physical add-on Lexus/Toyota OEM Remote Starter: The factory remote starter must be permanently disconnected before programming the Directed interface as both modules cannot coexist. See locating the OEM Remote Start on the next page. Ÿ If the vehicle is equipped with a BCM enabled Lexus/Toyota OEM Remote Starter: The vehicle does not have a physical remote starter and only one module can be programed at a time. In this case temporally disable the OEM remote start system using the following process: 1. Remove the fuse powering the OEM Remote Starter. See locating the fuse powering the OEM Remote Starter on the next page. 2. Perform a module reset, see « Module Reset » section. 3. Perform the Module Programming steps, see « Module Programming » section. After programming is successful replace the fuse powering the OEM Remote Starter. © 2017 Directed. All rights reserved. Platform: DBALL2 Firmware: TL8 Remote Start Ready (RSR) Installation Rev.: 20170824 Page 4 OEM Remote Start Fuse Location Make Lexus Lexus Lexus Lexus Lexus Lexus Lexus Lexus Lexus Lexus Model IS 200t (Smart Key) IS 250 (Smart Key) IS 300 (Smart Key) IS 350 (Smart Key) NX 200t (Smart Key) NX 300h (Smart Key) RC 350 (Smart Key) RC F (Smart Key) RX 350 (Smart Key) RX 450h (Smart Key) Fuse Location Engine room relay box, right side of engine compartment. Engine room relay box, right side of engine compartment. Engine room relay box, right side of engine compartment. Engine room relay box, right side of engine compartment. Engine room relay box, right side of engine compartment. Engine room relay box, right side of engine compartment. Engine room relay box, right side of engine compartment. Engine room relay box, right side of engine compartment. Bottom of instrument panel junction box, under drivers dash. Bottom of instrument panel junction box, under drivers dash. Fuse Name DCM DCM DCM DCM DCM DCM DCM DCM DCM DCM Fuse Value 5A 5A 5A 5A 5A 5A 5A 5A 7.5A 7.5A Physical OEM Remote Start Location Make Lexus Lexus Toyota Toyota Model IS 250 (Smart Key) IS 350 (Smart Key) Highlander (Smart Key) Highlander Hybrid OEM Remote Start Location Behind glove box, high in passenger kick panel. Behind glove box, high in passenger kick panel. Behind glove box, high in passenger kick panel. Bottom of instrument panel junction box, under drivers dash. © 2017 Directed. All rights reserved. Platform: DBALL2 Firmware: TL8 Remote Start Ready (RSR) Installation Rev.: 20170824 Page 5 Installation Type 1 Diagnostic Conn. OBDII HS CAN High: White, pin 6 1 8 9 16 HS CAN Low: Black, pin 14 Black conn. (at steering lock conn.) 7 6 5 4 3 2 1 [1] (-) SLP: Red, pin 4 [2] (-) PTS : Gray, pin 5 [2] (-) 14 HS CAN High: Tan/Black: 3 HS CAN Low: Tan: 4 Autolight Interr. (veh. side): Yellow: 8 Autolight Interr. (conn .side): Orange/Yellow: 9 (-) Ground: Yellow/Red: 11 (-) SLP Output: Brown/Red: 12 (+) 12V Input: Red: 13 (-) Ground: Black: 14 Hood Pin PTS Output: Green/Black: 2 10 12 (-) Unlock Output: Red/Black: 4 ENGINE START STOP Black Conn. 5 4 10 9 3 8 2 1 7 6 6: White/Black: (-) Hood Input (-) Lock Output: Blue/Red: 12 2 RF 4 Black, PTS Button Conn. (at PTS switch) Remote Start Safety Override Switch Prog. Button LED DBALL2 You can connect to either a XL202 RFTD OR a SmartStart module. Refer to the SmartStart/XL202 Installation Notes for more information. (-) Lock: Blue, pin 29 White Conn. (at Main Body ECU) Autolight: Pink, pin 8 (-) Unlock: Lt. Green, pin 2 36 35 34 33 32 31 30 29 28 (+) 12V: Blue, pin 13 [1] 18 17 16 15 14 13 27 26 25 24 23 22 21 20 19 12 11 10 9 8 7 6 5 4 3 2 1 Ma Bo in d EC y U CUT 19 20 21 22 23 24 25 26 27 28 29 30 7 8 9 10 11 12 13 14 15 16 17 18 4 5 6 1 2 3 White Conn. (at Main Body ECU) SLP: See « Locating Steering Lock Connector in Vehicle » in vehicle wiring reference chart. required for Pit Stop Mode. With the exception of the OBDII Diagnostic connector, all adapters are displayed from the wire side (unless specified otherwise). [2] Only © 2017 Directed. All rights reserved. Platform: DBALL2 Firmware: TL8 Remote Start Ready (RSR) Installation Rev.: 20170824 Page 6 Type 1 - Vehicle Wiring Reference Charts Wire information Connector Information Function Color Pin Polarity Location Lexus IS 200t (Smart key) 2016 SLP Red 4 (-) Steering lock connector. PTS Gray 5 (-) Engine start/stop switch. HS CAN High White 6 Data OBDII. HS CAN Low Black 14 Data OBDII. Autolight Pink 8 Cut Main body ECU. Lock Blue 29 (-) Main body ECU. Unlock Lt. Green 2 (-) Main body ECU. 12V Blue 13 (+) Main body ECU. Lexus IS 250 (Smart key) 2014-2015 SLP Red 4 (-) Steering lock connector. PTS Gray 5 (-) Engine start/stop switch. HS CAN High White 6 Data OBDII. HS CAN Low Black 14 Data OBDII. Autolight Pink 8 Cut Main body ECU. Lock Blue 29 (-) Main body ECU. Unlock Lt. Green 2 (-) Main body ECU. 12V Blue 13 (+) Dash fuse box. Lexus IS 300 (Smart key) 2016 SLP Red 4 (-) Steering lock connector. PTS Gray 5 (-) Engine start/stop switch. HS CAN High White 6 Data OBDII. HS CAN Low Black 14 Data OBDII. Autolight Pink 8 Cut Main body ECU. Lock Blue 29 (-) Main body ECU. Unlock Lt. Green 2 (-) Main body ECU. 12V Blue 13 (+) Main body ECU. Lexus IS 350 (Smart key) 2014-2016 SLP Red 4 (-) Steering lock connector. PTS Gray 5 (-) Engine start/stop switch. HS CAN High White 6 Data OBDII. HS CAN Low Black 14 Data OBDII. Autolight Pink 8 Cut Main body ECU. Lock Blue 29 (-) Main body ECU. Unlock Lt. Green 2 (-) Main body ECU. 12V Blue 13 (+) Main body ECU. Lexus RC350 (Smart Key) 2015-2016 SLP Red 4 (-) Steering lock connector. PTS Gray 5 (-) Engine start/stop switch. HS CAN High White 6 Data OBDII. HS CAN Low Black 14 Data OBDII. Autolight Pink 8 Cut Main body ECU. Lock Blue 29 (-) Main body ECU. Unlock Lt. Green 2 (-) Main body ECU. 12V Blue 13 (+) Dash fuse box. Lexus RC F (Smart Key) 2015 SLP Red 4 (-) Steering lock connector. PTS Gray 5 (-) Engine start/stop switch. HS CAN High White 6 Data OBDII. HS CAN Low Black 14 Data OBDII. Autolight Pink 8 Cut Main body ECU. Lock Blue 29 (-) Main body ECU. Unlock Lt. Green 2 (-) Main body ECU. 12V Blue 13 (+) Dash fuse box. Color Pin Black Black White White White White White White 7 10 16 16 30 30 30 36 Black Black White White White White White White 7 10 16 16 30 30 30 36 Black Black White White White White White White 7 10 16 16 30 30 30 36 Black Black White White White White White White 7 10 16 16 30 30 30 36 Black Black White White White White White White 7 10 16 16 30 30 30 36 Black Black White White White White White White 7 10 16 16 30 30 30 36 © 2017 Directed. All rights reserved. Platform: DBALL2 Firmware: TL8 Remote Start Ready (RSR) Installation Rev.: 20170824 Page 7 Type 1 - Locating Components and the OEM Remote Starter 30-pin White Connector 19 20 21 22 23 24 25 26 27 28 29 30 7 8 9 10 11 12 13 14 15 16 17 18 4 5 6 1 2 3 Main Body ECU and fusebox Push-to-start Button Diagnostic Connector Black Connector at Steering Lock (remove plastic) OEM Remote Start location: 2014-2015 Lexus IS 250/350 Ma Bo in d EC y U 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 36-pin conn. 7-pin Black Steering Lock Connector 7 6 5 4 3 2 1 10-pin Black Engine Start/Stop Switch 5 4 10 9 3 8 2 1 7 6 Black Connector ENGINE START STOP © 2017 Directed. All rights reserved. Platform: DBALL2 Firmware: TL8 Remote Start Ready (RSR) Installation Rev.: 20170824 Page 8 Type 1 - Locating SLP in the Vehicle 1. To gain access to the SLP connector, remove metal clip to remove the white plastic housing. 1 2. Move the white plastic housing over enough to access the SLP connector. 2 © 2017 Directed. All rights reserved. Platform: DBALL2 Firmware: TL8 Remote Start Ready (RSR) Installation Rev.: 20170824 Page 9 Installation Type 2 Diagnostic Conn. OBDII HS CAN High: Black, pin 6 1 8 9 16 HS CAN Low: White, pin 14 Black conn. (at steering lock conn.) 7 6 5 4 3 2 1 [1] (-) SLP: Yellow, pin 4 [2] (-) [2] (-) PTS: Lt.Green, pin 5 PTS Output: Green/Black: 2 10 Black Conn. Hood Pin 12 ENGINE START STOP 14 HS CAN High: Tan/Black: 3 HS CAN Low: Tan: 4 Autolight Interr. (veh. side): Yellow: 8 Autolight Interr. (conn .side): Orange/Yellow: 9 (-) Ground: Yellow/Red: 11 (-) SLP Output: Brown/Red: 12 (+) 12V Input: Red: 13 (-) Ground: Black: 14 5 4 10 9 3 8 2 1 7 6 (-) Unlock Output: Red/Black: 4 6: White/Black: (-) Hood Input (-) Lock Output: Blue/Red: 12 2 Black, PTS Button Conn. (at PTS switch) Remote Start Safety Override Switch RF 4 Prog. Button LED DBALL2 You can connect to either a XL202 RFTD OR a SmartStart module. Refer to the SmartStart/XL202 Installation Notes for more information. (-) Lock: Red, pin 29 White Conn. (at Dash Fuse Box) Autolight: Green, pin 8 (-) Unlock: Lt.Green,pin 2 (+) 12V: Red, pin 6 [1] 1 2 3 4 11 12 13 14 15 16 26 27 28 29 30 31 5 6 7 8 9 10 17 18 19 20 21 22 23 24 25 32 33 34 35 36 37 38 39 40 CUT 19 20 21 22 23 24 25 26 27 28 29 30 7 8 9 10 11 12 13 14 15 16 17 18 4 5 6 1 2 3 White Conn. (at Main Body ECU) Dash fuse box SLP: See « Locating Steering Lock Connector in Vehicle » in vehicle wiring reference chart. required for Pit Stop Mode. With the exception of the OBDII Diagnostic connector, all adapters are displayed from the wire side (unless specified otherwise). [2] Only © 2017 Directed. All rights reserved. Platform: DBALL2 Firmware: TL8 Remote Start Ready (RSR) Installation Rev.: 20170824 Page 10 Type 2 - Vehicle Wiring Reference Charts Wire information Connector Information Function Color Pin Polarity Location Lexus NX200t (Smart Key) 2015-2017 SLP Yellow 4 (-) Steering lock connector. PTS Lt. Green 5 (-) Engine start/stop switch. HS CAN High Black 6 Data OBDII. HS CAN Low White 14 Data OBDII. Autolight Green 8 Cut Bottom of dash fuse box. Lock Red 29 (-) Bottom of dash fuse box. Unlock Lt. Green 2 (-) Bottom of dash fuse box. 12V Red 6 (+) Bottom of dash fuse box. Lexus NX300h (Smart Key) 2015-2017 SLP Yellow 4 (-) Steering lock connector. PTS Lt. Green 5 (-) Engine start/stop switch. HS CAN High Black 6 Data OBDII. HS CAN Low White 14 Data OBDII. Autolight Green 8 Cut Bottom of dash fuse box. Lock Red 29 (-) Bottom of dash fuse box. Unlock Lt. Green 2 (-) Bottom of dash fuse box. 12V Red 6 (+) Bottom of dash fuse box. Color Pin Black Black White White White White White White 7 10 16 16 30 30 30 40 Black Black White White White White White White 7 10 16 16 30 30 30 40 Locating Components in the Vehicle 30-pin White Connector 19 20 21 22 23 24 25 26 27 28 29 30 7 8 9 10 11 12 13 14 15 16 17 18 4 5 6 1 2 3 Main Body ECU & Dash Fuse Box Dash fuse box Push-to-start Button Black Connector at Steering Lock (remove plastic) OBDII Diagnostic Connector 10-pin Black Engine Start/Stop Switch 5 4 10 9 3 8 2 1 7 6 Black Connector 7-pin Black Steering Lock Connector ENGINE START STOP 7 6 5 4 3 2 1 1 2 3 4 11 12 13 14 15 16 26 27 28 29 30 31 5 6 7 8 9 10 17 18 19 20 21 22 23 24 25 32 33 34 35 36 37 38 39 40 40-pin White © 2017 Directed. All rights reserved. Platform: DBALL2 Firmware: TL8 Remote Start Ready (RSR) Installation Rev.: 20170824 Page 11 Type 2 - Locating SLP in the Vehicle 1. To gain access to the SLP connector, remove metal clip to remove the white plastic housing. 1 2. Move the white plastic housing over enough to access the SLP connector. 2 © 2017 Directed. All rights reserved. Platform: DBALL2 Firmware: TL8 Remote Start Ready (RSR) Installation Rev.: 20170824 Page 12 Installation Type 3 Diagnostic Conn. OBDII HS CAN High: Violet or Lt. Blue, pin 6 1 8 9 16 HS CAN Low: White, pin 14 Black conn. (at steering lock conn.) 7 6 5 4 3 2 1 [1] (-) SLP: Lt.Green or Tan, pin 4 [2] [2] (-) (-) PTS: Yellow or Tan, pin 5 (-) Unlock Output: Red/Black: 4 5 4 10 9 3 8 10 Black Conn. Hood Pin PTS Output: Green/Black: 2 12 ENGINE START STOP 14 HS CAN High: Tan/Black: 3 HS CAN Low: Tan: 4 Autolight Interr. (veh. side): Yellow: 8 Autolight Interr. (conn .side): Orange/Yellow: 9 (-) Ground: Yellow/Red: 11 (-) SLP Output: Brown/Red: 12 (+) 12V Input: Red: 13 (-) Ground: Black: 14 Remote Start Safety Override Switch 2 1 7 6 6: White/Black: (-) Hood Input (-) Lock Output: Blue/Red: 12 2 RF 4 Black, PTS Button Conn. (at PTS switch) Prog. Button DBALL2 LED You can connect to either a XL202 RFTD OR a SmartStart module. Refer to the SmartStart/XL202 Installation Notes for more information. (-) Lock: Pin 29 CUT Autolight: Pin 8 (-) Unlock: Pin 2 19 20 21 22 23 24 25 26 27 28 29 30 7 8 9 10 11 12 13 14 15 16 17 18 4 5 6 1 2 3 White Conn. (at Main Body ECU) Ma Bo in d EC y U White conn. (at main body ECU) 1 [1] (+) 12V: Green or Black, pin 1 SLP: See « Locating Steering Lock Connector in Vehicle » in vehicle wiring reference chart. required for Pit Stop Mode. With the exception of the OBDII Diagnostic connector, all adapters are displayed from the wire side (unless specified otherwise). [2] Only © 2017 Directed. All rights reserved. Platform: DBALL2 Firmware: TL8 Remote Start Ready (RSR) Installation Rev.: 20170824 Page 13 Type 3 - Vehicle Wiring Reference Charts Wire information Connector Information Function Color Pin Polarity Location Toyota Highlander (Smart Key) 2014-2016 12V Green 1 (+) Dash fuse box. SLP Lt. Green 4 (-) Steering lock connector. PTS Yellow 5 (-) Engine start/stop switch. HS CAN High Violet 6 Data OBDII under driver dash. HS CAN Low White 14 Data OBDII under driver dash. Autolight Black 8 Cut Main body ECU. Lock Violet 29 (-) Main body ECU. Unlock Lt. Blue 2 (-) Main body ECU. Toyota Highlander Hybrid 2014-2016 12V Green 1 (+) Dash fuse box. SLP Lt. Green PTS Yellow HS CAN High Violet HS CAN Low White Autolight Black Lock Violet Unlock Lt. Blue Toyota Tacoma (Smart Key) 2016-2017 12V Black 4 5 6 14 8 29 2 (-) (-) Data Data Cut (-) (-) 1 (+) SLP PTS HS CAN High HS CAN Low Autolight Lock Unlock 4 5 6 14 8 29 2 (-) (-) Data Data Cut (-) (-) Tan Tan Lt.Blue White White Lt.Blue Green Color 30-pin White Connector Pin White Black Black White White White White White 1 7 10 16 16 30 30 30 White 1 Steering lock connector. Engine start/stop switch. OBDII under driver dash. OBDII under driver dash. Main body ECU. Main body ECU. Main body ECU. Black Black White White White White White 7 10 16 16 30 30 30 Dash fuse box. White 1 Steering lock connector. Engine start/stop switch. OBDII. OBDII. Main body ECU. Main body ECU. Main body ECU. Black Black White White White White White 7 10 16 16 30 30 30 19 20 21 22 23 24 25 26 27 28 29 30 7 8 9 10 11 12 13 14 15 16 17 18 4 5 6 1 2 3 Ma Bo in d EC y U 1 White 1-pin conn. Locating Components and the OEM Remote Starter 7-pin Black Steering Lock Connector 7 6 5 4 3 2 1 OEM Remote Start location: 2014-2016 Highlander (Smart key) & Hybrid 10-pin Black Engine Start/Stop Switch Main Body ECU and fusebox 5 4 10 9 3 8 2 1 7 6 Black Connector ENGINE START STOP Push-to-start Button Diagnostic Connector Black Connector at Steering Lock (remove plastic) © 2017 Directed. All rights reserved. Platform: DBALL2 Firmware: TL8 Remote Start Ready (RSR) Installation Rev.: 20170824 Page 14 Type 3 - Locating SLP in the Vehicle 1. To gain access to the SLP connector, remove metal clip to remove the white plastic housing. 1 2. Move the white plastic housing over enough to access the SLP connector. 2 © 2017 Directed. All rights reserved. Platform: DBALL2 Firmware: TL8 Remote Start Ready (RSR) Installation Rev.: 20170824 Page 15 Installation Type 4 HS CAN High: Lt.Blue, pin 6 10 9 24 8 7 23 6 5 22 21 20 19 18 17 16 15 14 13 4 3 2 1 Gateway ECU (behind the glove box) 12 11 Black conn. (at steering lock conn.) HS CAN Low: White, pin 21 7 6 5 4 3 2 1 [1] (-) SLP: Gray, pin 4 [2] (-) [2] 14 HS CAN High: Tan/Black: 3 HS CAN Low: Tan: 4 Autolight Interr. (veh. side): Yellow: 8 Autolight Interr. (conn .side): Orange/Yellow: 9 (-) Ground: Yellow/Red: 11 (-) SLP Output: Brown/Red: 12 (+) 12V Input: Red: 13 (-) Ground: Black: 14 Hood Pin PTS Output: Green/Black: 2 (-) PTS: Pink, pin 5 10 12 ENGINE START STOP Remote Start Safety Override Switch (-) Unlock Output: Red/Black: 4 5 4 10 9 3 8 2 1 7 6 6: White/Black: (-) Hood Input (-) Lock Output: Blue/Red: 12 2 RF 4 Black, PTS Button Conn. (at PTS switch) Prog. Button LED DBALL2 You can connect to either a XL202 RFTD OR a SmartStart module. Refer to the SmartStart/XL202 Installation Notes for more information. (-) Lock: Pink, pin 29 Autolight: Green, pin 8 CUT (-) Unlock: Violet, pin 2 19 20 21 22 23 24 25 26 27 28 29 30 7 8 9 10 11 12 13 14 15 16 17 18 4 5 6 1 2 3 (+) 12V: Blue, pin 1 1 White conn. (at Main Body ECU) [1] ECU (White conn. at Main Body ECU) Ma Bo in d EC y U SLP: See « Locating Steering Lock Connector in Vehicle » in vehicle wiring reference chart. required for Pit Stop Mode. Unless specified otherwise, all connectors are displayed from the wire side, with the exception of the OBDII diagnostic connector. [2] Only © 2017 Directed. All rights reserved. Platform: DBALL2 Firmware: TL8 Remote Start Ready (RSR) Installation Rev.: 20170824 Page 16 Type 4 - Vehicle Wiring Reference Charts Wire information Function Color Pin Polarity Location Lexus RX350 2016-2017 Connector Information Color Pin 12V Blue 1 (+) SLP Gray 4 (-) PTS Pink 5 (-) HS CAN High Lt. Blue 6 Data HS CAN Low White 21 Data Lock Pink 29 (-) Unlock Violet 2 (-) Autolight Green 8 Cut Lexus RX450h (Smart key) 2016-2017 Dash fuse box. Steering lock connector on steering column. Engine start/stop switch. Network Gateway ECU behind glovebox. Network Gateway ECU behind glovebox. Main body ECU. Main body ECU. Main body ECU. White Black Black Black Black White White White 1 7 10 24 24 30 30 30 12V Blue 1 (+) Dash fuse box. White 1 SLP Gray 4 (-) Steering lock connector on steering column. Black 7 PTS Pink 5 (-) Engine start/stop switch. Black 10 HS CAN High Lt. Blue 6 Data Network Gateway ECU behind glovebox. Black 24 HS CAN Low White 21 Data Network Gateway ECU behind glovebox. Black 24 Autolight Green 8 Cut Main body ECU. White 30 Lock Pink 29 (-) Main body ECU. White 30 Unlock Violet 2 (-) Main body ECU. White 30 Locating Components in the Vehicle 30-pin White Connector 19 20 21 22 23 24 25 26 27 28 29 30 7 8 9 10 11 12 13 14 15 16 17 18 4 5 6 1 2 3 Main Body ECU and fusebox Push-to-start Button Black Connector at Steering Lock (remove plastic) Diagnostic Connector 10-pin Black Engine Start/Stop Switch 5 4 10 9 3 8 2 1 7 6 Black Connector Network Gateway ECU Ma Bo in ECdy U 7-pin Black Steering Lock Connector ENGINE START STOP 1 7 6 5 4 3 2 1 White 1-pin conn. © 2017 Directed. All rights reserved. Platform: DBALL2 Firmware: TL8 Remote Start Ready (RSR) Installation Rev.: 20170824 Page 17 Type 4 - Locating SLP in the Vehicle 1. To gain access to the SLP connector, remove metal clip to remove the white plastic housing. 1 2. Move the white plastic housing over enough to access the SLP connector. 2 © 2017 Directed. All rights reserved. Platform: DBALL2 Firmware: TL8 Remote Start Ready (RSR) Installation Rev.: 20170824 Page 18 Installation Type 5 Data Steering connector Black conn. (at steering lock conn.) HS CAN High: Tan, pin 3 HS CAN Low: White, pin 2 7 6 5 4 3 2 1 [1] (-) SLP: Lt. Green, pin 4 [2] (-) [2] (-) PTS : Yellow, pin 5 10 Black Conn. Hood Pin PTS Output: Green/Black: 2 12 ENGINE START STOP 14 HS CAN High: Tan/Black: 3 HS CAN Low: Tan: 4 Autolight Interr. (veh. side): Yellow: 8 Autolight Interr. (conn .side): Orange/Yellow: 9 (-) Ground: Yellow/Red: 11 (-) SLP Output: Brown/Red: 12 (+) 12V Input: Red: 13 (-) Ground: Black: 14 5 4 10 9 3 8 2 1 7 6 Remote Start Safety Override Switch (-) Unlock Output: Red/Black: 4 6: White/Black: (-) Hood (-) Lock Output: Blue/Red: 12 2 RF 4 Black, PTS Button Conn. (at PTS switch) Prog. Button LED DBALL2 You can connect to either a XL202 RFTD OR a SmartStart module. Refer to the SmartStart/XL202 Installation Notes for more information. (-) Lock: Violet, pin 29 Autolight: Black, pin 8 CUT (-) Unlock: Lt. Blue, pin 2 19 20 21 22 23 24 25 26 27 28 29 30 7 8 9 10 11 12 13 14 15 16 17 18 4 5 6 1 2 3 White Conn. (at Main Body ECU) Ma Bo in d EC y U White conn. (at Main Body ECU) 1 [1] (+) 12V: Green,pin 1 SLP: See « Locating Steering Lock Connector in Vehicle » in vehicle wiring reference chart. required for Pit Stop Mode. Unless specified otherwise, all connectors are displayed from the wire side, with the exception of the OBDII diagnostic connector. [2] Only © 2017 Directed. All rights reserved. Platform: DBALL2 Firmware: TL8 Remote Start Ready (RSR) Installation Rev.: 20170824 Page 19 Type 5 - Vehicle Wiring Reference Charts Wire Information Connector Information Function Color Pin Polarity Location Toyota Highlander (Smart Key) 2017 12V Green 1 (+) Dash fuse box. Yellow PTS 5 (-) PTS switch. Tan HS CAN High 3 Data Steering sensor on steering column. HS CAN Low White 2 Data Steering sensor on steering column. SLP Lt. Green 4 (-) Steering lock connector. Autolight Black 8 Cut Main body ECU. Lock Violet 29 (-) Main body ECU. Unlock Lt. Blue 2 (-) Main body ECU. Toyota Highlander Hybrid 2017 12V Green 1 (+) Dash fuse box. Yellow PTS 5 (-) PTS switch. Tan HS CAN High 3 Data Steering sensor on steering column. HS CAN Low White 2 Data Steering sensor on steering column. SLP Lt. Green 4 (-) Steering lock connector. Autolight Black 8 Cut Main body ECU. Lock Violet 29 (-) Main body ECU. Unlock Lt. Blue 2 (-) Main body ECU. Color Pins White Black Blue Blue 1 10 5 5 Black White White White 7 30 30 30 White Black 1 10 5 Blue Blue Black White White White 5 7 30 30 30 Locating Components and the OEM Remote Starter 30-pin White Connector 19 20 21 22 23 24 25 26 27 28 29 30 7 8 9 10 11 12 13 14 15 16 17 18 4 5 6 1 2 3 OEM Remote Start location: 2014-2016 Highlander (Smart key) & Hybrid Main Body ECU and fusebox Push-to-start Button Diagnostic Connector 10-pin Black Engine Start/Stop Switch 5 4 10 9 3 8 2 1 7 6 Black Connector Ma Bo in d EC y U Black Connector at Steering Lock (remove plastic) 7-pin Black Steering Lock Connector ENGINE START STOP Data Steering sensor 7 6 5 4 3 2 1 3 2 1 White 1-pin conn. © 2017 Directed. All rights reserved. Platform: DBALL2 Firmware: TL8 Remote Start Ready (RSR) Installation Rev.: 20170824 Page 20 Type 5 - Locating SLP in the Vehicle 1. To gain access to the SLP connector, remove metal clip to remove the white plastic housing. 1 2. Move the white plastic housing over enough to access the SLP connector. 2 © 2017 Directed. All rights reserved. Platform: DBALL2 Firmware: TL8 Remote Start Ready (RSR) Installation Rev.: 20170824 Page 21 Installation Type 6 White Conn. (at Main Body ECU) 36 35 34 33 32 31 30 29 28 (+) 12V: Blue, pin 13 27 26 25 24 23 22 21 20 19 CUT (-) Lock: Blue, pin 29 (-) Unlock: Lt.Green, 19 20 21 22 23 24 25 26 27 28 29 30 pin 2 7 8 9 10 11 12 13 14 15 16 17 18 4 5 6 1 2 3 12 11 10 9 8 7 18 17 16 15 14 13 Autolight: Pink, pin 8 HS CAN Low: Black, pin 13 White Conn. (at Main Body ECU) HS CAN High: Yellow, pin 14 Ma Bo in d EC y U 6 5 4 3 2 1 Black conn. (at steering lock conn.) 7 6 5 4 3 2 1 [2] (-) PTS: Gray, pin 5 [2] (-) 3 8 2 1 7 6 PTS Output: Green/Black: 2 PTS Button Conn. (Black conn. at PTS switch) 10 5 4 10 9 Hood Pin 12 ENGINE START STOP 14 [1] (-) SLP: Red, pin 4 HS CAN High: Tan/Black: 3 HS CAN Low: Tan: 4 Autolight Interr. (veh. side): Yellow: 8 Autolight Interr. (conn .side): Orange/Yellow: 9 (-) Ground: Yellow/Red: 11 (-) SLP Output: Brown/Red: 12 (+) 12V Input: Red: 13 (-) Ground: Black: 14 Remote Start Safety Override Switch (-) Unlock Output: Red/Black: 4 6: White/Black: (-) Hood Input (-) Lock Output: Blue/Red: 12 2 RF 4 Prog. Button LED DBALL2 You can connect to either a XL202 RFTD OR a SmartStart module. Refer to the SmartStart/XL202 Installation Notes for more information. [1] SLP: See « Locating Steering Lock Connector in Vehicle » in vehicle wiring reference chart. required for Pit Stop Mode. With the exception of the OBDII Diagnostic connector, all adapters are displayed from the wire side (unless specified otherwise). [2] Only © 2017 Directed. All rights reserved. Platform: DBALL2 Firmware: TL8 Remote Start Ready (RSR) Installation Rev.: 20170824 Page 22 Type 6 - Vehicle Wiring Reference Charts Wire Information Function Color Lexus IS200t (Smart Key) 2017 SLP Red PTS Gray HS CAN High Yellow HS CAN Low Black Autolights Pink Lock Blue Unlock Lt. Green 12V Blue Lexus IS300 (Smart Key) 2017 SLP Red PTS Gray HS CAN High Yellow HS CAN Low Black Autolights Pink Lock Blue Unlock Lt. Green 12V Blue Lexus IS350 (Smart Key) 2017 SLP Red PTS Gray HS CAN High Yellow HS CAN Low Black Autolights Pink Lock Blue Unlock Lt. Green 12V Blue Connector Information Pin Polarity Location Color Pins 4 5 14 13 8 29 2 13 (-) (-) Data Data Cut (-) (-) (+) Steering lock connector on steering column. Engine start/stop switch. Main body ECU. Main body ECU. Main body ECU. Main body ECU. Main body ECU. Main body ECU. Black Black White White White White White White 7 10 30 30 30 30 30 36 4 5 14 13 8 29 2 13 (-) (-) Data Data Cut (-) (-) (+) Steering lock connector on steering column. Engine start/stop switch. Main body ECU. Main body ECU. Main body ECU. Main body ECU. Main body ECU. Main body ECU. Black Black White White White White White White 7 10 30 30 30 30 30 36 4 5 14 13 8 29 2 13 (-) (-) Data Data Cut (-) (-) (+) Steering lock connector on steering column. Engine start/stop switch. Main body ECU. Main body ECU. Main body ECU. Main body ECU. Main body ECU. Main body ECU. Black Black White White White White White White 7 10 30 30 30 30 30 36 Locating Components in the Vehicle Main Body ECU & Dash Fuse Box Push-to-start Button OBDII Diagnostic Connector Black Connector at Steering Lock (remove plastic) © 2017 Directed. All rights reserved. Platform: DBALL2 Firmware: TL8 Remote Start Ready (RSR) Installation Rev.: 20170824 Page 23 Type 6 - Locating SLP in the Vehicle 1. To gain access to the SLP connector, remove metal clip to remove the white plastic housing. 1 2. Move the white plastic housing over enough to access the SLP connector. 2 © 2017 Directed. All rights reserved. Platform: DBALL2 Firmware: TL8 Remote Start Ready (RSR) Installation Rev.: 20170824 Page 24 SmartStart/XL202 Installation Notes The DBALL Remote Start Ready (RSR) solution offers three (3) configuration options to control your system: 3x OEM Lock Remote Start Activation, RF Kits or SmartStart (all sold separately). This section provides specific installation information for SmartStart and XL202. SmartStart Revision A SmartStart is optional and not included. It MUST be purchased separately. Configuration Wires (White & Brown or Blue) Cut Brown or Blue Loop OR 4 pins DBALL2 SmartStart 2 pins, not used CABLE LED D2D (4 pins, white) The modules must be connected in a specific order. Refer to the Module Programming section for more information. SmartStart Revision B SmartStart is optional and not included. It MUST be purchased separately. Configuration Wires (Gray & White) Connect Gray wire to (-) Ground 5 pins 4 pins DBALL2 THIS SIDE UP 2 pins, not used CABLE D2D (4 pins, white) LED The modules must be connected in a specific order. Refer to the Module Programming section for more information. RF Kit The optional XL202 and antenna are not included and MUST be purchased separately. 4 XL202 XOVER Antenna LED DBALL2 4 Prog. Button 1. Use the D2D Crossover (XOVER) cable that is provided with XL202, and NOT the one in the DBALL2 package. 2. The modules must be connected in a specific order. Refer to the Module Programming section for more information. RF Kit & PKE Combination Refer to the Passive Keyless Entry (PKE) Installation Guide (N2102T) for detailed wiring information. RF Kit, PKE & SmartStart BT Combination Refer to the Passive Keyless Entry (PKE) Installation Guide (N2102T) for detailed wiring information. © 2017 Directed. All rights reserved. Platform: DBALL2 Firmware: TL8 Remote Start Ready (RSR) Installation Rev.: 20170824 Page 25 Module Programming Refer to the LED Diagnostics section for more information and for troubleshooting purposes. Important Make all the required connections to the vehicle, as described in the wiring diagram(s) found in this guide, and double check to ensure everything is correct prior to moving onto the next step. Note: Before connecting either the XL202 or SmartStart module to DBALL2, it is important to ensure that the proper feature and function programming is selected using XpressVIP (version 4.5 or higher). Visit www.directechs.com to download the latest version of the application. Warning! To take advantage of advanced features, you must use XpressVIP 4.5 (and higher) or the Directechs Mobile app. Flashing a module using your computer: 1. Connect the interface module to your computer using the XKLoader2. 2. Go to www.directechs.com using Internet Explorer, and select the Config for RSR button. 3. Follow the instructions to select your vehicle, installation type, and configure your options. 4. Once you have configured the firmware options, click on the FLASH button. Flashing a module using your smartphone or tablet 1. Connect the interface module to your XKLoader3. 2. Launch the Directechs Mobile app on your smartphone or tablet. 3. Select FLASH YOUR MODULE and follow the on screen instructions. SmartStart Installation The DBALL2 module must be disconnected from any power source before SmartStart can be connected to it. Failing to do so could damage DBALL2. a. To ensure that the D2D communication between SmartStart and DBALL2 works properly, the Gray wire must be connected to a ground source (Rev B SmartStart), and the Brown or Blue loop must be cut (Rev A SmartStart). b. Do NOT connect the 2-pin harness (on SmartStart). Power and ground will be provided by the DBALL2 D2D connector. Connect SmartStart to DBALL2 using the D2D port. SmartStart D2D 0-pin 1 OR XL202 Installation Connect XL202 to DBALL2 using the D2D port. 1 2 in 14-p 2-pin 1 D2D 0-pin 1 Connect the 10-pin, 12-pin and 14-pin harnesses to DBALL2, then wait until the LED turns ON solid red. 1 st Press the Push-to-Start (PTS) button twice to turn the ignition ON. The green LED turns ON for 3 seconds. If the module flashes orange, your vehicle is equipped with a factory remote starter. See section ‘Important OEM Remote Starter Information’ on page 3. Note: If the transponder programming was skipped, the LED turns on solid orange for 3 seconds then shuts OFF when programming is done. 3 D2D 0-pin 1 XL202 Press the PTS button once more to turn the ignition OFF. 3rd & 2nd ENGINE START STOP Solid PUSH 2X & Solid x3 Secs ENGINE START STOP PUSH 1X You have successfully completed the module programming sequence. © 2017 Directed. All rights reserved. Platform: DBALL2 Firmware: TL8 Remote Start Ready (RSR) Installation Rev.: 20170824 Page 26 Module Reset A module reset will only erase programming performed in the previous steps. All settings (firmware) and settings flashed to the module using the web config tool will not be affected. 1 2 If required for your installation, connect the 10-pin & 12-pin harnesses to the module. Press and hold the programming button, then connect the 14-pin harness to the module. in 14-p 2-pin 1 D2D 0-pin 1 4th st 1 Wait 3 seconds until the LED turns ON solid orange then release the programming button. The LED turns ON solid red. 2nd 3rd & & Release Solid Solid Hard Reset Warning Against Executing a Hard Reset! A hard reset will revert the flashed firmware back to its default settings. Depending on the installation, some settings (such as RFTD and D2D options) may have to be reconfigured. See the Feature & Option List section of this guide. 1 2 If required for your installation, connect the 10-pin & 12-pin harnesses to the module. Press and hold the programming button, then connect the 14-pin harness to the module. in 14-p 2-pin 1 D2D 0-pin 1 st 1 4th 2nd 3rd Wait 3 seconds until the LED turns ON solid orange, and wait 10 more seconds until the LED starts to flash orange and red. & Solid 3 Flashes & Release the programming button. The LED turns ON solid red. Release Solid © 2017 Directed. All rights reserved. Platform: DBALL2 Firmware: TL8 Remote Start Ready (RSR) Installation Rev.: 20170824 Page 27 Feature & Option List It is recommended to configure all the features and options listed below using the configuration tool found on the module flashing page on www.directechs.com. The web offers more options; however, manual configuration of the features is possible using the information on this page. * Default Option Feat. Operation 1 RFTD Output Type 2 Unlock Driver Priority Flashes/Option 1. No RF Output* 2. RFTD Output 3. SmartStart 1. Driver priority* 2. All 1. Disabled 2. Safelock 3 4 3. Enabled* Smart OEM Alarm Control will synchronize with the OEM alarm so that it will disarm and rearm the vehicle in the remote start sequence, only when required. The reason for this is, factory alarm control must often be done by lock or unlock operation. This could create unnecessary actions on door lock modules, such as the horn to honk. When possible, Smart OEM Alarm Control will monitor the alarm and door lock status to detect if the disarm or rearm is required. If the vehicle is unlocked or is not equipped with factory alarm, the disarm/rearm will not be executed. Smart OEM Alarm Control will also monitor the remote starter actions so that the factory alarm control is not done twice. A remote starter, for which the Safelock feature is active, will work perfectly with this option and will make it invisible to the user. 1. Not Equipped* 2. Equipped The vehicle is not equipped with an automatic trunk/hatch opening system. The vehicle is equipped with an automatic trunk/hatch opening system. Smart OEM Alarm Control Motorized Hatch Equipped Description Module is connected to a remote starter using a standard installation. Module is connected to an XL202 using an RSR or RXT installation (when available). Module is connected to SmartStart using an RSR or RXT installation (when available). Unlocks only the driver door when the button is first pressed, and unlocks all doors when it is pressed a second time within 5 seconds. Unlocks all doors when the button is first pressed. The OEM alarm will not be controlled by DBALL upon remote start. No disarm or arm command will be executed at the beginning or end of the sequence; it must be controlled by the Remote Starter. Smart OEM Alarm Control will behave like a standard Safelock feature on a remote starter. It will unlock at the beginning of the sequence, and relock after start and shutdown. Feature Programming Programming Button To enter feature programming routine - Turn the ignition ON, then OFF. - Within 5 seconds, press and HOLD the programming button until the LED turns ON orange (after 3 seconds). Release the Programming button. - The LED will flash green once slowly to indicate the feature number is 1. After a short delay, the LED flashes red rapidly to indicate the current option of feature 1 (i.e. 1x green followed by 1x red indicates feature 1 is set to option 1). The flashing sequence will repeat until a new command is entered. Changing feature options - Press the lock/arm or unlock/disarm button on aftermarket transmitter to change the option of the selected feature. When installing the DBALL in RSR using 3x OEM Lock Remote Start Activation only, there is no aftermarket transmitter on which to press lock/unlock to change the options of the selected feature. Tapping the green or blue lock/unlock wires on the black 10-pin harness to ground will change the option for the selected feature. - The LED flashes red rapidly the number of times equal to the current option number. After a short delay, the LED flashes green slowly the number of times to indicate the current feature. The flashing sequence will repeat until a new command is entered. Accessing another feature - Press and release the programming button a number of times to advance from the current feature to the next desired feature. - The LED flashes green slowly the number of times equal to the feature number. After a short delay, the LED flashes red rapidly to indicate the current option of the current feature. The flashing sequence will repeat until a new command is entered. When the maximum number of features or options is reached, the LED will start flashing again from the first feature or option. Once a feature is programmed - Other features can be programmed. - The feature programming can be exited. Exiting feature programming - No activity for 30 seconds; after 30 seconds, the LED will turn ON orange for 2 seconds to confirm the end of the programming sequence. OR - Press and HOLD the programming button for 3 seconds. After 3 seconds, the LED will turn ON orange for 2 seconds to confirm the end of the programming sequence. © 2017 Directed. All rights reserved. Platform: DBALL2 Firmware: TL8 Remote Start Ready (RSR) Installation Rev.: 20170824 Page 28 LED Diagnostics & Troubleshooting LED Description Module Programming Off Module has no power. Solid red Waiting to begin the programming sequence. Troubleshooting Make sure the D2D harness is connected or that the 12 Volt is present between the red and black wires. If the 12 Volt is present, the module may be defective. Ensure the correct programming procedure is being followed. Initialization failed. Reset the module and complete the programming again. If the issue persists, please contact Technical Support. Solid orange Transponder functions were skipped. (If compatible) when RXT mode is not desired or convenience features are needed, please reset and reprogram the module. Flashes green All required CAN networks has been detected. Normal operation. Flashes orange 1 of 2 CAN networks has been detected. Normal operation Flashes orange slowly Key2GO initiated. Please follow the steps indicated in “Module programming” to complete the Key2GO programming. Solid green x 3 secs Module was successfully programmed with all functions. Normal operation Flashes red & green Module was successfully programmed without transponder functions. Module Programming - Error Codes Solid orange x 3 secs Flashes red x1 CAN2 not detected. Flashes red x1 J1850 not detected. Flashes red x2 CAN1 not detected. Flashes red x3 Bypass data not detected. Flashes red x4 Bypass processing error. Flashes red x5 ISO 1 not detected. Flashes red x6 ISO 2 not detected. Flashes red x7 MUX not detected. Normal operation. Check the CAN2 Orange/Green and Orange/Brown wire connections. Wake up the data bus by turning the ignition on and try again. If your installation does not require this connection, skip this step by pressing the programming button 5 times. Check the J1850 wire connection. Wake up the data bus by turning the ignition on and try again. Check the CAN1 Tan and Tan/Black wire connections. Wake up the data bus by turning the ignition on and try again. If your installation does not require this connection, skip this step by pressing the programming button 5 times. Check the bypass line connection. If more than one wire is used, make sure they are not inverted. Ensure the vehicle still operates correctly using the factory key. The bypass calculation failed. Reset the module and try again. If the condition persists, please contact Technical Support. The Yellow/Black wire did not detect the expected signal. Refer to "Installation (wiring diagrams & vehicle wiring reference charts)" to check the connections. The Orange/Black wire did not detect the expected signal. Refer to "Installation (wiring diagrams & vehicle wiring reference charts)" to check the connections. The Violet/Green or Violet/Brown wire did not detect the expected voltage value. Refer to "Installation (wiring diagrams & vehicle wiring reference charts)" to check the connections. © 2017 Directed. All rights reserved. Platform: DBALL2 Firmware: TL8 Remote Start Ready (RSR) Installation Rev.: 20170824 Page 29 LED Diagnostics & Troubleshooting LED Description External module synchronization (Flashes red, red then orange) x 10 OBDII feature is not supported. Troubleshooting The diagnostic data bus was not detected, therefore the SmartStart features will be limited. Activation Ground When Running (Status) Flashes green Flashes red & orange Ground When Running (Status) command received. The module has initialized the remote start sequence. Ignition ON command received. The module has received the Ignition ON command and is processing the remote start sequence. Flashes green quickly Start ON command received. Flashes red x 10 PTS shutdown error. Flashes red x 21 CAN bus incorrectly detected. The module has received the Start ON command and is processing the remote start sequence. The PTS output from the module was not activated due to safety protection. Verify the CAN1 and CAN2 connections. Refer to “Installation (wiring diagrams & vehicle wiring reference charts)” to check the connections. Commands Flashes orange x 1 LOCK command received. Flashes orange x 2 UNLOCK command received. Flashes orange x 3 TRUNK command received. Flashes orange x 4 AUX1 command received. Flashes orange x 5 AUX2 command received. Flashes orange x 6 AUX3 command received. If the bypass module fails to flash, it did not receive the signal. Commands can come from RF or D2D. Shutdown codes Flashes green x 1 Takeover successful. Flashes red x1 Runsafe was not disabled. Flashes red x2 Brake was not detected. Flashes red x3 Smart key was not detected. Flashes red x4 Speed was detected. Normal operation. No UNLOCK command was received prior to opening the door, or the 45 second timer expired in takeover mode. The brakes were not detected, which prevents the system from shutting down the vehicle. The smart key was not detected, which prevents the system from shutting down the vehicle. The vehicle was detected as moving, which prevents the system from shutting it down. © 2017 Directed. All rights reserved. Platform: DBALL2 Firmware: TL8 Remote Start Ready (RSR) Installation Rev.: 20170824 Page 30 Parking Light Error Codes The parking lights on your vehicle will flash a specific number of times 3 seconds following an unscheduled shutdown or failure to start. Each flashing pattern is described below. Flashes Diagnostic 1 Runtime expired. 2 Over-rev shutdown. 3 Low/No RPM. 4 Transmitter shutdown. 5 Brake shutdown. 6 Hood shutdown/Remote start safety override switch is ON*. 7 Remote start safety override switch is ON*. * If the vehicle hood status is supported through data, safety override switch input will report 7 flashes. © 2017 Directed. All rights reserved. Platform: DBALL2 Firmware: TL8 Remote Start Ready (RSR) Installation Rev.: 20170824 Page 31 Limited One Year Consumer Warranty For a period of ONE YEAR from the date of purchase of a Directed Electronics remote start or security product, Directed Electronics. (“DIRECTED”) promises to the original purchaser, to repair or replace with a comparable reconditioned piece, the security or remote start accessory piece (hereinafter the “Part”), which proves to be defective in workmanship or material under normal use, provided the following conditions are met: the Part was purchased from an authorized DIRECTED dealer; and the Part is returned to DIRECTED, postage prepaid, along with a clear, legible copy of the receipt or bill of sale bearing the following information: consumer’s name, address, telephone number, the authorized licensed dealer’s name and complete product and Part description. This warranty is nontransferable and is automatically void if the Part has been modified or used in a manner contrary to its intended purpose or the Part has been damaged by accident, unreasonable use, neglect, improper service, installation or other causes not arising out of defect in materials or construction. TO THE MAXIMUM EXTENT ALLOWED BY LAW, EXCEPT AS STATED ABOVE, ALL WARRANTIES, INCLUDING BUT NOT LIMITED TO EXPRESS WARRANTY, IMPLIED WARRANTY, WARRANTY OF MERCHANTABILITY, FITNESS FOR PARTICULAR PURPOSE AND WARRANTY OF NONINFRINGEMENT OF INTELLECTUAL PROPERTY, ARE EXPRESSLY EXCLUDED; AND DIRECTED NEITHER ASSUMES NOR AUTHORIZES ANY PERSON OR ENTITY TO ASSUME FOR IT ANY DUTY, OBLIGATION OR LIABILITY IN CONNECTION WITH ITS PRODUCTS. DIRECTED HEREBY DISCLAIMS AND HAS ABSOLUTELY NO LIABILITY FOR ANY AND ALL ACTS OF THIRD PARTIES INCLUDING DEALERS OR INSTALLERS. DIRECTED IS NOT OFFERING A GUARANTEE OR INSURANCE AGAINST VANDALISM, DAMAGE, OR THEFT OF THE AUTOMOBILE, ITS PARTS OR CONTENTS, AND DIRECTED HEREBY DISCLAIMS ANY LIABILITY WHATSOEVER, INCLUDING WITHOUT LIMITATION, LIABILITY FOR THEFT, DAMAGE, OR VANDALISM. IN THE EVENT OF A CLAIM OR A DISPUTE INVOLVING DIRECTED OR ITS SUBSIDIARY, THE PROPER VENUE SHALL BE SAN DIEGO COUNTY IN THE STATE OF CALIFORNIA. CALIFORNIA STATE LAWS AND APPLICABLE FEDERAL LAWS SHALL APPLY AND GOVERN THE DISPUTE. THE MAXIMUM RECOVERY UNDER ANY CLAIM AGAINST DIRECTED SHALL BE STRICTLY LIMITED TO THE AUTHORIZED DIRECTED DEALER’S PURCHASE PRICE OF THE PART. DIRECTED SHALL NOT BE RESPONSIBLE FOR ANY DAMAGES WHATSOEVER, INCLUDING BUT NOT LIMITED TO, ANY CONSEQUENTIAL DAMAGES, INCIDENTAL DAMAGES, DAMAGES FOR THE LOSS OF TIME, LOSS OF EARNINGS, COMMERCIAL LOSS, LOSS OF ECONOMIC OPPORTUNITY AND THE LIKE. NOTWITHSTANDING THE ABOVE, THE MANUFACTURER DOES OFFER A LIMITED WARRANTY TO REPLACE OR REPAIR AT DIRECTED’S OPTION THE PART AS DESCRIBED ABOVE. This warranty only covers Parts sold within the United States of America and Canada. Parts sold outside of the United States of America or Canada are sold “AS-IS” and shall have NO WARRANTY, express or implied. Some states do not allow limitations on how long an implied warranty will last or the exclusion or limitation of incidental or consequential damages. This warranty gives you specific legal rights and you may also have other rights that vary from State to State. DIRECTED does not and has not authorized any person or entity to create for it any other obligation, promise, duty or obligation in connection with this Part. For further details relating to warranty information of Directed products, please visit the support section of DIRECTED’s website at: www.directed.com 920-10012-01 2013-07 This Interface kit / Data Bus Interface part has been tested on the listed vehicles. Other vehicles will be added to the select vehicle list upon completion of compatibility testing. Visit website for latest vehicle application guide. DISCLAIMER: Under no circumstances shall the manufacturer or the distributors of the bypass kit / data bus interface part(s) be held liable for any consequential damages sustained in connection with the part(s) installation. The manufacturer and it’s distributors will not, nor will they authorize any representative or any other individual to assume obligation or liability in relation to the interface kit / data bus interface part(s) other than its replacement. N.B.: Under no circumstances shall the manufacturer and distributors of this product be liable for consequential damages sustained in connection with this product and neither assumes nor authorizes any representative or other person to assume for it any obligation or liability other than the replacement of this product only. Protected by U.S. Patents: 5,719,551; 6,011,460 B1 *; 6,243,004 B1; 6,249,216 B1; 6,275,147 B1; 6,297,731 B1; 6,346,876 B1; 6,392,534 B1; 6,529,124 B2; 6,696,927 B2; 6,756,885 B1; 6,756,886 B2; 6,771,167 B1; 6,812,829 B1; 6,924,750 B1; 7,010,402 B1; 7,015,830 B1; 7,031,826 B1; 7,046,126 B1; 7,061,137 B1; 7,068,153 B1; 7,205,679 B1; Cdn. Patent: 2,320,248; 2,414,991; 2,415,011; 2,415,023; 2,415,027; 2,415,038; 2,415,041; 2,420,947; 2,426,670; 2,454,089; European Patent: 1,053,128; Pat. Pending: 2,291,306. Made in Canada. © 2017 Directed. All rights reserved. Quick Reference Guide DBALL2-TL8 Remote Start Ready (RSR) Installation Vehicle Takeover Remote Start Ready (RSR) Remote Start Ready (RSR) is a function that enables the interface module to remote start the vehicle completely on its own. Consequently, there is no need for an aftermarket or an OEM remote starter in order to start the vehicle from a distance. Note: There is no vehicle takeover in this firmware. The vehicle will shut down as soon as a door is opened. Pit Stop Mode The Pit Stop Mode feature is practical when you need to stop and run an errand, but wish to keep the engine running. 1 Stop the vehicle in a safe parking spot and put the gear in Park (P). & P Stop & put vehicle in Park (P) 2 3 Press the button to remote start the vehicle.* The parking lights will flash once to indicate the vehicle is now in Pit Stop Mode. It is now safe to leave the engine running and exit the vehicle with the factory remote in hand. Press remote start button* 3x OEM Lock Remote Start Activation This solution includes the option to remote start your vehicle by pressing the Lock button 3 times consecutively. If your vehicle allows the OEM remote to remain active while the engine is running, you may shut down your remote starter by pressing the Lock button 3 times once more. Note: The range offered by OEM remotes is limited and typically requires you to be within eyesight of the vehicle to control it. Parking Light Error Codes H O LD Note: We recommend that you always lock the doors of your vehicle when leaving it unattended. Exit vehicle with Smart Key * Your aftermarket remote may differ from the model shown in the illustrations. The parking lights on your vehicle will flash a specific number of times 3 seconds following an unscheduled shutdown or failure to start. Each flashing pattern is described below. Flashes Diagnostic 1 Runtime expired. 2 Over-rev shutdown. 3 Low/No RPM. 4 Transmitter shutdown. 5 Brake shutdown. 6 Hood shutdown/Remote start safety override switch is ON*. 7 Remote start safety override switch is ON*. * If the vehicle hood status is supported through data, safety override switch input will report 7 flashes. © 2017 Directed. All rights reserved. Quick Reference Guide DBALL2-TL8 Remote Start Ready (RSR) Installation SmartStart Compatible List of Available Commands Note that the information below is for Viper, Clifford and Python models. Icons and commands may differ depending on the remote brand and model purchased. Refer to your authorized installation center for more information. Button(s) Actions This system is compatible with Directed SmartStart 3.0. For a complete list of supported features, please visit www.mysmartstart.com. What is SmartStart? Press & hold for 1 second to lock. Press & hold for 1 second to unlock. Now you can remote start, lock and unlock your car just by pushing a button on your smartphone; using the SmartStart App from Directed, the leader in vehicle security and remote start. The simple graphical interface gives you control over the following features of your installed remote start or security with remote start system: Press & hold for 5 seconds to activate the trunk release (optional). Ÿ Ÿ Ÿ Ÿ Ÿ Ÿ x1 + Press once, then to activate the rear hatch/tail glass release (optional).* You can also control multiple vehicles – great for families – and assign more than one user to control a vehicle. It's easy with SmartStart! x3 + Press 3 times, then the panic mode. But, this is only the beginning! SmartStart is loaded with additional features including GPS tracking, SmartSchedule, vehicle status, roadside assistance, home control, parked car finder and more. x1 + Press once, then remote starter runtime. Press & hold for 1 second to remote start. to activate to reset the * This output is configurable. see your authorized installation center for more information. Lock/Arm Unlock/Disarm Remote Car Starter Trunk Release Panic Aux Channels 3.0 enables a "Cloud-Connected Car" like never before, providing an entirely new level of 2-way interaction with your vehicle. Connectivity is managed through the Directed Cloud Services (DCS) network linking car, app, end user, and the Internet. For more information, visit www.mysmartstart.com. Notes © 2017 Directed. All rights reserved.