Official Software
Get notified when we add a new LexusOther Model Manual

We cover 38 Lexus vehicles, were you looking for one of these?

Lexus - LS 460 - Workshop Manual - (2007)
Lexus - GS 300 - Workshop Manual - (1993)
Lexus - GS 350 - Workshop Manual - (2007)
Lexus - LS 400 - Workshop Manual - (1990)
Lexus - LS 460 - Workshop Manual - (2009)
Lexus - SC 430 - Workshop Manual - (2003)
Lexus - GS 300 - Workshop Manual - (2004)
Lexus - GS 450 - Workshop Manual - (2007)
Lexus - Auto - Lexus_2008_IS_350_250-mk-OM53650U
Lexus - GS 350 - Wiring Diagram - (2009)
Lexus - Auto - Lexus_2008_IS_350_250-mk-OM53650U_5d8a7fb2205698a85417799
Lexus - Auto - Lexus_2008_IS_F-mk-OM53714U
Lexus - SC 400 - Workshop Manual - (1997)
Lexus - Auto - Lexus_2011_IS_F-mk-OM53893U
Lexus - Auto - Lexus_2009_IS_F-mk-OM53700U
Lexus - Auto - Lexus_2012_IS_F-mk-OM53A41U
Lexus - Auto - Lexus_2008_IS_F-mk-OM53613U_5d8a7fb2c2cfd1a40044054
Lexus - Auto - Lexus_2010_IS_F-mk-OM53A25U_5d8a7f7210dd69a35589660
Lexus - Auto - Lexus_2014_IS_F-mk-OM53C33U_5d8a7f721ad2a8a05142317
Lexus - Auto - Lexus_2010_IS_F-mk-OM53A25U
Lexus - Auto - Lexus_2013_IS_F-mk-OM53B49U
Lexus - Auto - Lexus_2009_IS_F-mk-OM53700U_5d8a7f869d7b95a96244745
Lexus - Auto - Lexus_2009_IS_F-mk-OM53706U_5d8a7f8892bd82a93490888
Lexus - Auto - Lexus_2014_IS_F-mk-OM53C15U
Lexus - Auto - Lexus_2012_IS_F-mk-OM53A41U_5d8a7fb2bf9a84a89164869
Lexus - Auto - Lexus_2014_IS_F-mk-OM53C15U_5d8a7f840dfc50a73415738
Lexus - Auto - Lexus_2014_IS_F-mk-OM53C33U
Lexus - Auto - Lexus_2008_IS_F-mk-OM53714U_5d8a7fb221eaf2a24629815
Lexus - Auto - Lexus_2011_IS_F-mk-OM53A11U_5d8a7f733c8fe6a02660009
Lexus - Auto - Lexus_2010_IS_F-mk-OM53791U
Lexus - Auto - Lexus_2010_IS_F-mk-OM53791U_5d8a7f6645bde2a08742526
Lexus - Auto - Lexus_2008_IS_F-mk-OM53613U
Lexus - Auto - Lexus_2011_IS_F-mk-OM53A11U
Lexus - Auto - Lexus_2009_IS_F-mk-OM53706U
Lexus - Auto - Lexus_2013_IS_F-mk-OM53B59U
Lexus - Auto - Lexus_2013_IS_F-mk-OM53B49U_5d8a7f77b34583a28557958
Lexus - Auto - Lexus_2011_IS_F-mk-OM53893U_5d8a7f625f6623a15657710
Lexus - Auto - Lexus_2013_IS_F-mk-OM53B59U_5d8a7f87562bc8a15409052
Summary of Content
Sikky Lexus IS-F/350/250 Sway Bar Installation Instructions Included in your package: -Sway Bar (1) -Endlinks (2) -Bushings (2) Step 1. Remove all items from the box. Step 2. To begin removal of the factory sway bar, loosen the lower 19mm rear shock bolts to release the pinch on the factory endlinks. Do not remove the bolt. Step 3. Remove the lower sway bar 12mm link nuts. Step 4. Remove the 12mm sway bar retainer bolts. Step 5. Pull the factory endlinks up and out of the control arm. Rotate the bar and slide out towards the driver side. Step 6. Apply bushing grease inside the provided bushings. Step 7. Open the bushing where it is sliced and slide over the sway bar. Position as shown. Step 8. Make sure the bottom of the bushing is the round side. Step 9. Slide bar into place from the driver side to the passenger side. Step 10. Reinstall 12mm sway bar retainer bolts- do not tighten. Step 11. After all bolts have been started make sure the bushing is properly installed. It needs to be aligned and centered as shown. Step 12. Once the bushings are properly aligned, you can now tighten the four 12mm bushing retainer bolts. Step 13. Rotate the bar out of the way to make clearance for the sway bar endlinks. Slide bottom of endlinks into place and align with hole. Step 14. Start the 12mm sway bar retainer bolts. Do not tighten. *NOTE: On the driver’s side make sure the ride level sensor is attached like the factory setup. Step 15. Install the upper sway bar link into the hole of your choice. The correct order is- washer, sway bar, washer, and nut. Now hand tighten the nut. Do not tighten the jam nuts located above and below the endlink turn buckle, leaving free play adjustment. Hand tighten Do not tighten jam nuts Step 16. Once the endlinks are in tighten the lower 12mm sway bar retainer bolts. *Note: Make sure the ride level sensor bracket stays located in the back hole. Step 17. Tighten the 19mm lower shock bolts to factory specs. Step 18. Fully tighten down the endlink nut. The endlink bolt is 16mm and the nut is 19mm. Instructions for Setting Zero Preload Step 1: Remove both rear wheels Step 2: Set jack stands under lowest knuckle points Step 3: Lower vehicle till all weight is supported by the jack stands. The suspension now has full load on it. Step 4. The endlink turn buckle will have pressure on it. Turn it clockwise and counter clockwise until the pressure is relieved. Step 5. Now that the turn buckle is free, twist is clockwise until it stops and note the position. Then twist it counter clockwise until it stops and note the position. Center the turn buckle in between the 2 noted positions and you will be set at zero pre load. Step 6. Using a 7/8” wrench hold the turn buckle in place while using a 19mm wrench to tighten both jam nuts. Tighten the nuts just so they are snug, DO NOT OVER TIGHTEN. -Now double check all bolts are tightened down to factory torque specs - Road test -Enjoy!