Nissan - Tiida - Workshop Manual - 2008 - 2011

2008-2011 NISSAN TRUCKS AUTOMATIC & MANUAL TRANSMISSIONS General Applicability This cruise control was tested and verified on: 2008 - 2011 Nissan Frontier 2008 - 2011 Nissan Titan This cruise control may not function correctly on unverified vehicles. See www.rostra.com for vehicle compatibility. ELECTRONIC CRUISE CONTROL KIT PART NUMBER: 250-1856 Recommended Tools Safety Tools Safety Glasses Special Tools Kit Contents/Service Parts Volt-Ohm Meter Item # 1 2 3 4 5 6 7 Qty 1 1 1 1 1 1 1 Description Cruise Control Module Switch Harness Main Wiring Harness Pedal Interface Harness Hardware Kit Control Switch Terminal Harness (Not Shown) 4 6 Service Part # 250-2789 250-2760 250-2759 250-2771 250-2767 250-3742 250-2774 Installation Tools Trim Removal Tool Drill Bit/Knockout Punch 10mm wrench Soldering Tool 9.5mm or 3/8” (for switch) Special Chemicals 3 2 Conflicts Note: 5 1 Legend STO Contents of Hardware Bag Qty 8 Description Wire Zip Ties STOP: Damage to the vehicle may occur. Do not proceed until process has been complied with. OPERATOR SAFETY: Use caution to avoid risk of injury CRITICAL PROCESS: Proceed with caution to ensure a quality installation. GENERAL PROCESS: This highlights specific processes to ensure a quality installation. TOOLS & EQUIPMENT: This calls out the specific tools and equipment required for this process WARNING: DO NOT USE HAND-HELD 2-WAY TRANSCEIVERS INSIDE YOUR VEHICLE WHILE DRIVING. WHEN TRANSMITTING FROM INSIDE THE CAR, 2-WAY RADIOS THAT OPERATE IN THE 25MHZ-700MHZ FREQUENCY RANGE WITH MORE THAN 2.0 WATTS OF POWER CAN PRODUCE ELECTROMAGNETIC INTERFERENCE THAT COULD INTERFERE WITH THE OPERATION OF CRUISE AND THROTTLE CONTROLS RESULTING IN VEHICLE "LIMP MODE". USE OF CELLULAR PHONES WILL NOT INTERFERE WITH THESE CONTROLS. DUE TO SENSITIVE NATURE OF SIGNALS USED FOR THIS PRODUCT, ALL NON-PLUG AND PLAY CONNECTIONS MUST BE SOLDERED. FAILURE TO COMPLY WITH THIS REQUIREMENT WILL VOID WARRANTY. Form #5222, Rev: E, 09-30-10 2008-2011 NISSAN TRUCKS AUTOMATIC & MANUAL TRANSMISSIONS ELECTRONIC CRUISE CONTROL KIT PART NUMBER: 250-1856 Section I – Installation Procedure A. Pre-Installation Suggestions 1. It is advisable to disconnect the negative battery cable for 3 minutes before beginning installation, to avoid unintended air bag deployment. Note and record any anti-theft radio codes prior to disconnecting. Figure 1 2. Remove driver side lower dash panel, kick panel, steering wheel shroud, and instrument cluster panel. Figure 2 Figure 1 B. Install Electronic Module 1. Plug in the Main Wiring Harness, Switch Harness, and Pedal Interface Harness onto mating connectors of the Cruise Control Module. Figure 3 2. Place the Cruise Control Module in the secure location behind the driver side dash area near the firewall away from moving parts. 3. Route the Pedal Interface Harness through steering column and down to the accelerator. Form #5222, Rev: E, 09-30-10 Figure 2 Figure 3 2008-2011 NISSAN TRUCKS AUTOMATIC & MANUAL TRANSMISSIONS ELECTRONIC CRUISE CONTROL KIT PART NUMBER: 250-1856 C. Install Pedal Interface Harness 1. Use the diagram and chart below to install the pedal interface harness. Disconnect the Pedal Interface Harness at the 2-pin connectors to ease installation of solder connections. Cut the selected wires at the accelerator harness leaving at least 2 inches of harness from the connector. Solder the wire ends from the pedal interface harness to the accelerator pedal harness according to each wire color listed in chart. After soldering, wrap the exposed wires with electrical tape. Figure 4. WARNING: PROCEED WITH CAUTION TO BE SURE PEDAL INTERFACE HARNESS IS MATED PROPERLY TO THE ACCELERATOR HARNESS. FAILURE TO DO THIS CORRECTLY WILL DISABLE THE ACCELERATOR. : Solder Joint Connector Side Harness Side Red Yellow White Green Figure 4 TITAN CONNECTIONS FRONTIER CONNECTIONS Splice & Solder Direction Cruise Harness Color Vehicle Wire Splice & Solder Direction Cruise Harness Color Vehicle Wire CONNECTOR RED GREEN/RED CONNECTOR RED GRAY CONNECTOR WHITE BROWN/WHITE CONNECTOR WHITE RED HARNESS YELLOW GREEN/RED HARNESS YELLOW GRAY HARNESS GREEN BROWN/WHITE HARNESS GREEN RED Form #5222, Rev: E, 09-30-10 2008-2011 NISSAN TRUCKS AUTOMATIC & MANUAL TRANSMISSIONS ELECTRONIC CRUISE CONTROL KIT PART NUMBER: 250-1856 2. Check for good solder connection: Before continuing cruise installation, plug the 2-pin mating connectors in to each other as shown in Figure 5. Reconnect negative side of battery. Start engine and depress accelerator to confirm operation. Turn off engine and disconnect battery. 2-pin Red/White Harness To Pedal Harness a. If a DTC code appears, restart Section C and ensure proper wire matching and good solder connections. ACCEL PEDAL YEL RED GRN WHT 3. Unplug the 2-pin mating connectors from each other (connected together in the last step) and reconnect to the 2-pin mating connectors of Pedal Interface Harness. Use electrical tape to wrap all connections. Figure 5 D. Wiring Connections (See Wiring Harness Description on last page) 1. Use the following wiring diagram as a reference to make the following connections if vehicle connections are not listed in the instructions: CLUTCH (GND TRG) White CLUTCH (+12V TRG) Yellow Cruise Module 12V IGN Red VSS Violet GND Black Form #5222, Rev: E, 09-30-10 BRAKE + Blue BRAKE White/Brown 2008-2011 NISSAN TRUCKS AUTOMATIC & MANUAL TRANSMISSIONS ELECTRONIC CRUISE CONTROL KIT PART NUMBER: 250-1856 E. Nissan Frontier Wiring Connections 1. Locate the following wires to connect to the main harness from the control module: Function See Fig. Vehicle Color IGN 1 WHITE/GREEN BRAKE + 2 RED/BLACK BRAKE - 2 YELLOW GROUND 3 GROUND POINT VSS 6 PIN 6 OR BLUE CLUTCH Driver Kick Panel IGN Figure 1 PAGE 4 Brake Switch 2. Connect the Main Harness to vehicle wire by using the chart below. Function Cruise Harness Color Vehicle Wire IGN RED WHITE/GREEN BRAKE + BLUE RED/BLACK BRAKE - WHITE/BROWN YELLOW VSS VIOLET PIN 6 OR BLUE CLUTCH WHITE OR YELLOW PAGE 4 PIN 1 RED/BLACK PIN 2 YELLOW Figure 2 3. Apply the Black Ground Wire from the Main Harness to the Vehicle Ground Point at the lower dash panel frame. Figure 3 GND Form #5222, Rev: E, 09-30-10 Figure 3 2008-2011 NISSAN TRUCKS AUTOMATIC & MANUAL TRANSMISSIONS F. Nissan Titan Wiring Connections ELECTRONIC CRUISE CONTROL KIT PART NUMBER: 250-1856 Driver Kick Panel 1. Locate the following wires to connect to the main harness from the control module: Function See Fig. Vehicle Color IGN 1 WHITE/RED BRAKE + 2 RED/YELLOW BRAKE - 2 RED/BLACK GROUND 3 GROUND POINT VSS 7 PIN 29 IGN Figure 1 Brake Switch 2. Connect the Main Harness to vehicle wire by using the chart below: Function Cruise Harness Color Vehicle Wire IGN RED WHITE/RED BRAKE + BLUE RED/YELLOW BRAKE - BROWN/WHITE RED/BLACK VSS VIOLET PIN 29 PIN 1 RED/YELLOW PIN 2 RED/GREEN Figure 2 GND 3. Apply the Black Ground Wire from the Main Harness to the Vehicle Ground Point at the lower dash panel frame. Figure 3 Figure 3 Form #5222, Rev: E, 09-30-10 2008-2011 NISSAN TRUCKS AUTOMATIC & MANUAL TRANSMISSIONS ELECTRONIC CRUISE CONTROL KIT PART NUMBER: 250-1856 Nissan Frontier/Titan Connections Continued… 4. Frontier VSS: Locate the white 40-pin connecter at the instrument cluster. If Blue Wire is present in pin 6, connect the Violet Wire from the cruise harness to the Blue Wire in pin 6. If Blue Wire is not present in pin 6, use a precision tool to release the retainer of the connector. Figures 4-5. Locate the terminal harness supplied in kit. Insert the terminal end of the harness into pin 6. Figure 6. Titan VSS: Locate the white 40-pin connecter at the instrument cluster. If Red/White Wire is present in pin 29, connect the Violet Wire from the cruise harness to the Red/White Wire in pin 29. If Red/White Wire is not present in pin 29, use a precision tool to release the retainer of the connector. Figures 4-5 Locate the terminal harness supplied in kit. Insert the terminal end of the harness into pin 29. Figure 7 Make sure terminal locks into connector and replace retainer 5. Connect the terminal harness to the Violet Wire of the cruise harness. Secure Cruise Control Module harnesses with zip ties away from moving parts Retainer Locked Figure 4 Retainer released Figure 5 Frontier PIN 6 Figure 6 Titan PIN 29 Figure 7 Form #5222, Rev: E, 09-30-10 2008-2011 NISSAN TRUCKS AUTOMATIC & MANUAL TRANSMISSIONS ELECTRONIC CRUISE CONTROL KIT PART NUMBER: 250-1856 G. Install Control Switch 1. Use the lever wedges on the Control Switch at an angle template to drill a 3/8” or 9.5mm hole in the lower shroud of the steering column cover. Position lock-washers as shown. Figure 1 2. Apply nut and position Control Switch for driver’s best view. 3. Assemble (2) 3-pin connectors from the sack parts to the mating wire colors on the Control Switch Harness. Use the diagram to mate the module harness to switch harness. Figure 2 4. Route the assembled Control Switch Harness to the mating connector of the Cruise Control Module. Figure 1 From Module 5. Secure the Control Switch Harness with zip ties away from moving parts. H. Testing 1. Reconnect negative battery cable and torque to 35 in*lbs. Reenter anti-theft radio codes. 2. Turn ignition on. Apply the on/off button of Cruise Control Switch. I. Reassembly 1. Reinstall all removed pieces taking care to ensure harnesses and wiring connections are properly secured. 2. Make sure all harnesses are not pinched or bound by trim pieces. Form #5222, Rev: E, 09-30-10 Figure 2 Figure 3 From Switch 2008-2011 NISSAN TRUCKS AUTOMATIC & MANUAL TRANSMISSIONS ELECTRONIC CRUISE CONTROL KIT PART NUMBER: 250-1856 Section II - Wiring Diagram - Green 4 volts Ignition White 4 volts Ignition Yellow 2 volts Ignition Red 2 volts Ignition Note: All Pedal Interface Harness Voltages are with pedal fully depressed Form #5222, Rev: E, 09-30-10 2008-2011 NISSAN TRUCKS AUTOMATIC & MANUAL TRANSMISSIONS ELECTRONIC CRUISE CONTROL KIT PART NUMBER: 250-1856 TROUBLESHOOTING Function Color Results Fault Conditions Ignition Red 12 volts when switched on and zero (0) volts when switched off. Must not disappear when starting vehicle. No power, voltage drop, or intermittent connection will cause Loss of pedal or “Limp Mode” condition. Brake positive + Blue “Hot” side of brake switch. 12 volts all the time. Cruise will not function if this connection is not installed correctly. Brake negative - Brown/White “Cold side of Brake switch. Zero (0) Cruise will not function if this connection is not installed correctly. If connection is good, and there is a high resistance to ground, a 5 terminal relay will be required to complete installation. See diagram below. Ground Black Lowest resistance to ground closest to zero (0) ohms as possible. Use a vehicle ground point where other ground wires are connected to. A bad ground connection will cause the following conditions: Cruise will not function; Loss of pedal or “Limp Mode” condition. VSS Violet Vehicle speed sensor circuit Cruise will not function if this connection is not installed correctly. Clutch or NSS White 12 volts active or ground active wire at switch when clutch is depressed or neutral safety switch is engaged. Cruise will not function if wrong wire is connected. Cruise will not disengage when clutch is depressed or when switched to neutral if installed incorrectly. resistance to ground when brake is not pressed. 12 volts when brake is pressed. 5 Terminal Relay for Brake Switch Not Used Ground 86 87 87a Brake - 85 30 Ground Form #5222, Rev: E, 09-30-10 Brown/White of Cruise Harness 2008-2011 NISSAN TRUCKS AUTOMATIC & MANUAL TRANSMISSIONS Notes: Form #5222, Rev: E, 09-30-10 ELECTRONIC CRUISE CONTROL KIT PART NUMBER: 250-1856