Official Software
Get notified when we add a new NissanOther Model Manual

We cover 60 Nissan vehicles, were you looking for one of these?

2007 Nissan Tiida Model C11 Series Service Repair Manual PDF
Nissan Micra Model K12 Series Service Repair Manual PDF
Nissan Qashqai Model J11 Series Service Repair Manual
Nissan Note Model E11 Series Service Manual PDF
Nissan QASHQAI Model J10 Series Electronic Service Manual
NISSAN PATROL GQ MODEL Y60 SERIES SERVICE REPAIR MANUAL
2001 Nissan Primera Model P11 Service Repair Manual PDF
2013 Nissan Leaf Model ZE0 series Service Manual PDF
Nissan Pathfinder 2006 Model R51 Service Repair Manual PDF
2001 Nissan Almera N16 series Service Manual PDF
2016 Nissan Juke Model F15 Series Service and Repair Manual PDF
Nissan Note Model E12 Series Service Manual PDF
1998 NISSAN PATROL GR Y61 SERIES SERVICE MANUAL PDF
Nissan Primastar X83 series Service Manual PDF
2005-2006 Nissan Altima Model L31 Factory Service Manual PDF
2008 Nissan Altima Model L32 Service Repair Manual PDF
2001-2005 Nissan Primera P12 ESM (Electronic Service Manual)
2004 Nissan 350z Service & Repair Manual (SM4E-1Z33U8)
Nissan - Tiida - Owners Manual - 2006 - 2020
Nissan Patrol Model Y61 Series Electronic Service Manual
Nissan Patrol Model Y61 Series ESM (Electronic Service Manual)
Nissan Terrano 2004 Service and Repair Manual
2002 Nissan Sentra Service Repair Manual (SM2E-1B15U2)
2014 Nissan Leaf Model ZE0 series Service Manual PDF
1992 Nissan Serena C23 Service Manual PDF
2014 Nissan Sentra Service Repair Manual (SM14E00B17U0)
2007 Nissan 350Z-Z33 Service Repair Manual PDF
2007 Nissan Qashqai Repair Manual (SM7E00-1J10E1E)
2011 Nissan Pathfinder Service and Repair Manual
2011 Nissan Maxima Repair Manual
Nissan - Auto - nissan-serena-2012-104086
2009 Nissan Murano Repair Manual (SM9E-1Z51U2)
2014 Nissan Juke Model F15 Series Service Manual PDF
2012 Nissan Leaf Model ZE0 series Service Manual PDF
2008 Nissan Pathfinder Service and Repair Manual
2004-2005 Nissan Altima Model L31 Factory Service Manual PDF
Nissan - Cabstar - Workshop Manual - 1994 - 1999
2005 Nissan 350z Service & Repair Manual (SM5E-1Z33U2)
2006 Nissan Note Model E11 Series Electronic Service Manual
2003 Nissan Pathfinder Service and Repair Manual
Nissan Patrol Y62 Technical Training Manual
2006 Nissan Murano Repair Manual (SM6E-1Z50U0)
Nissan Qashqai J10 ESM (Electronic Service Manual) January 2007
2003 Nissan 350z Service & Repair Manual (SM3E-1Z33U0)
2013 Nissan Pathfinder Service and Repair Manual
2005 Nissan Titan Repair Manual (SM5E-1A60U0)
2010 Nissan Sentra Service Repair Manual (SM0E-1B16U1)
Nissan - Pixo - Owners Manual - 2009 - 2020
Nissan - Patrol Y61 - Workshop Manual - 2007 - 2007
1999-2002 Nissan Primera P11 ESM (Electronic Service Manual)
2008 Nissan 350z Service & Repair Manual (SM8E-1Z33U1)
2004 Nissan Sentra Service Repair Manual (SM4E-1B15U1)
Sentra SE-R Spec V L4-2.5L (QR25DE) (2002)
2012 Nissan Quest Model E52 Series Service Repair Manual
2006 Nissan Patrol Model Y61 Series Electronic Service Manual
Nissan - Pulsar - Workshop Manual - 1990 - 1990
2007 Nissan Pathfinder Service and Repair Manual
2012 Nissan Pathfinder Service and Repair Manual
2014 Nissan Pathfinder Service and Repair Manual
2011 Nissan Armada Service Repair Manual
Summary of Content
Getting The Most From Your NISSAN NP300 HARDBODY OWNER’S MANUAL WELCOME TO YOUR NEW NISSAN NP300 HARDBODY CONTENTS Illustrated table of contents 0 Safety — seats, seat belts and supplemental restraint system 1 Instruments and controls 2 Pre-driving checks and adjustments 3 Heater and air conditioner, and audio system 4 Starting and driving 5 In case of emergency 6 Appearance and care 7 Maintenance and do-it-yourself 8 Technical information 9 Index 10 Foreword.fm Page 1 Tuesday, October 29, 2013 9:06 AM Foreword Welcome to the growing family of new NISSAN owners. This vehicle has been delivered to you with confidence. Your vehicle has been produced using the latest techniques and strict quality control. This manual has been prepared to help you understand the operation and maintenance of your vehicle so that you may enjoy many kilometres of driving pleasure. Please read through this manual before operating your vehicle. A separate “Warranty Information & Maintenance” booklet explains details about the warranties covering your vehicle. Remember that your NISSAN Dealer knows your vehicle best. When you require any service or have any questions about your vehicle, they will be glad to assist you with the extensive resources available to you. IMPORTANT SAFETY INFORMATION READ FIRST - THEN DRIVE SAFELY REMINDERS FOR SAFETY Before driving your vehicle please read your Owner's Manual carefully. This will ensure familiarity with controls and maintenance requirements, assisting you in the safe operation of your vehicle. Follow these four important driving rules to help ensure a safe and complete trip for you and your passengers! • NEVER drive under the influence of alcohol or drugs. • ALWAYS observe posted speed limits and never drive too fast for conditions. • ALWAYS use your seat belts and appropriate child restraint systems. • ALWAYS provide information about the proper use of vehicle safety features to all occupants of the vehicle. Throughout this manual we have used the symbol followed by the word WARNING. This is used to indicate the presence of a hazard which may cause the possibility of a personal injury or other damage and must be followed precisely. CAUTION. This is also used throughout the manual to indicate the presence of a hazard that could cause possible minor injury to yourself or components and the procedures must be followed carefully. WHEN READING THE MANUAL This manual includes information for all options available on this model. Therefore, you may find some information that does not apply to your vehicle. • For descriptions specified for 4-wheel drive models a mark is placed at the beginning of the applicable sections/ items. (c)!2018 NISSAN S.A.! PRETORIA, SOUTH AFRICA Foreword.fm Page 2 Tuesday, October 29, 2013 9:06 AM ON-ROAD AND OFF-ROAD DRIVING MODIFICATION OF YOUR VEHICLE This vehicle will handle and manoeuvre differently from an ordinary passenger car, because it has a higher centre of gravity for off-road use. As with other vehicles with features of this type, failure to operate this vehicle correctly may result in loss of control or an accident. This vehicle should not be modified. Modification could affect its performance, safety or durability, and may even violate governmental regulations. In addition, damage or performance problems resulting from modification may not be covered under NISSAN warranties. Be sure to read the On-Road and Off-Road driving precautions in the “5. Starting and driving” section of this manual. All information, specifications and illustrations in this manual are those in effect at the time of printing. NISSAN reserves the right to change specifications or design at any time without notice and without obligation. (c)!2018 NISSAN S.A.! PRETORIA, SOUTH AFRICA Chapter1TOC.fm Page 0 Thursday, April 11, 2013 2:43 PM 1 Safety - seats, seat belts and supplemental restraint system Seats..........................................................................................................1-1 Seat adjustment (if so equipped) ...................................................1-1 Tilting front bucket set (if so equipped)........................................1-1 Tilting bench seat...............................................................................1-2 Adjustable head restraints (if so equipped).................................1-2 Seat belts..................................................................................................1-3 Precautions on seat belt usage ......................................................1-3 Seat belt maintenance ......................................................................1-4 3-point type seat belts......................................................................1-4 2-point type seat belts......................................................................1-5 Child restraints ............................................................................. 1-7 Precautions on child restraints usage................................ 1-7 Installation of child restraint system ................................... 1-9 Supplemental restraint system (if so equipped).................1-12 Driver and front passenger air bag system..................... 1-12 Driver airbag system ............................................................1-15 Air bag warning label (if so equipped).............................1-18 Air bag warning light (if so equipped).............................. 1-18 Pre-tensioner seat belt system (if so equipped) ........... 1-19 Chapter1.fm Page 1 Thursday, April 11, 2013 2:41 PM SEATS SEAT ADJUSTMENT (if so equipped) WARNING • • Do not adjust the driver's seat while driving. The seat may move suddenly and could cause loss of control of the vehicle. After adjustment, gently rock in the seat to make sure it is securely locked. Forward and backward Pull the lever up and hold it while you slide the seat forward or backward to the desired position. Release the lever to lock the seat in position. Reclining (except bench seat) Pull the lever up and lean back until the desired angle is obtained. To bring the seat back forward again, pull the lever and move your body forward. The seat back will move forward. WARNING The seat back should not be reclined any more than needed for comfort. Seat belts are most effective when the passenger sits well back and straight up in the seat. If the seat back is reclined, the risk of sliding under the lap belt and being injured is increased. TILTING FRONT BUCKET SEAT (if so equipped) The front passenger’s seat can be tilted to make it easier for passengers to get in and out. To tilt the back rest, pull the reclining lever up or push the tilt lever down. The seat automatically moves forward. To return the seat, move the whole seat backward, then push the back rest up until it locks. WARNING After adjustment, gently rock in the seat to make sure it is securely locked. Safety - seats, seat belts and supplemental restraint system 1-1 Chapter1.fm Page 2 Thursday, April 11, 2013 2:41 PM Single cab model Double cab model (rear seat) TILTING BENCH SEAT The bench seat can be tilted to make it easier to remove the jacking tools from the storage area. To tilt the seat back, pull the lever up or pull the strap up and push the seat back forward . For some single cab models, the lever located behind the driver seat. is ADJUSTABLE HEAD RESTRAINTS (If so equipped) Adjust the centre of the head restraints to be level with the centre of your ears. To raise the head restraint, just pull it up. To lower, push the lock knob and push the head restraint down. After adjustment, make sure that it is securely locked. WARNING Head restraints should be adjusted properly as they may provide significant protection against whiplash injury. 1-2 Safety - seats, seat belts and supplemental restraint system Chapter1.fm Page 3 Thursday, April 11, 2013 2:41 PM SEAT BELTS • PRECAUTIONS ON SEAT BELT USAGE NISSAN strongly encourages you and all of your passengers to buckle up every time you drive. Your chances of being injured in an accident and/or the severity of injury may be greatly reduced if you are wearing your seat belt and it is properly adjusted. • It is essential to replace the entire assembly after it has been worn in a severe impact even if damage to the assembly is not obvious. • Belts should not be worn with straps twisted. • Each seat belt assembly must only be used by one occupant; it is dangerous to put a belt around a child being carried on the occupant's lap. WARNING • • • Seat belts are designed to bear upon the bony structure of the body and should be worn low across the front of the pelvis, or the pelvis, chest and shoulders, as applicable; wearing the lap section of the belt across the abdominal area must be avoided. Serious injury can occur if seat belt is not worn properly. No modifications or additions should be made by the user which will either prevent the seat belt adjusting devices from operating to remove slack, or prevent the seat belt assembly from being adjusted to remove slack. Seat belts should be adjusted as firmly as possible, consistent with comfort, to provide the protection for which they have been designed. A slack belt will greatly reduce the protection afforded to the wearer. Care should be taken to avoid contamination of the webbing with polishes, oils and chemicals, and particularly battery acid. Cleaning may safely be carried out using mild soap and water. The belt should be replaced if webbing becomes frayed, contaminated or damaged. • It is compulsory by law that every person who drives or rides in this vehicle should wear a seat belt at all times. Children should be in appropriate child restraints. • Do not allow more than one person at a time to use the same belt. • Your NISSAN Dealer should inspect all seat belt assemblies including retractors and attaching hardware after any collision. NISSAN recommends that all seat belt assemblies in use during a collision be replaced unless the collision was minor and the belts show no damage and continue to operate properly. Seat belt assemblies not in use during a collision should also be inspected and replaced if either damage or improper operation is noted. Infant or small child NISSAN recommends that infants or small children be seated in a child restraint. You should choose a child restraint system that fits your vehicle and always follow the manufacturer's instructions for installation and use. Children Children who are too large for a child restraint should be seated and restrained by the seat belts, which are provided. NISSAN recommends that children sit in the rear seat if available. According to accident statistics, children are safer when properly restrained in the rear seat than in the front seat. If the child's seating position has a shoulder belt that fits close to the face or neck, the use of a booster seat (commercially available) may help overcome this. The booster seat should raise the child so that the shoulder belt is properly positioned across the top middle portion of the shoulder and the lap belt is low on the hips. The booster seat should fit the vehicle seat. Once the child has grown so the shoulder belt is no longer on or near the face and neck, use the shoulder belt without the booster seat. Never let a child stand or kneel on any seat and do not allow a child in the cargo areas while the vehicle is moving. Safety - seats, seat belts and supplemental restraint system 1-3 Chapter1.fm Page 4 Thursday, April 11, 2013 2:41 PM Pregnant women NISSAN recommends that pregnant women use seat belts. Contact your doctor for specific recommendations. The lap belt should be worn snug and positioned as low as possible around the hips, not the waist. Injured persons NISSAN recommends that injured persons use seat belts, depending on the injury. Check with your doctor for specific recommendations. SEAT BELT MAINTENANCE • • • To clean the seat belt webbings, apply a mild soap solution or any solution recommended for cleaning upholstery or carpets. Then brush it, wipe with a cloth and allow it to dry in the shade. Do not allow the seat belts to retract until they are completely dry. If dirt builds up in the shoulder belt guide of the seat belt anchors, the seat belts may retract slowly. Wipe the shoulder belt guide with a clean, dry cloth. Periodically check to see that the seat belt and the metal components such as buckles, tongues, retractors, flexible wires and anchors work properly. If loose parts, deterioration, cuts or other damage on the webbing is found, the entire belt assembly should be replaced. 3-POINT TYPE WITH RETRACTOR The retractor is designed to lock during a sudden stop or on impact. A slow pulling motion will permit the belt to move, and allow you some freedom of movement in the seat. Every person who drives or rides in this vehicle should wear a seat belt at all times. Fastening the belts 1 Adjust the seat. WARNING The seat back should not be in a reclining position any more than needed for comfort. Seat belts are most effective when the passenger sits well back and straight up in the seat. If the seat is reclined, the risk of sliding under the lap belt and being injured is increased. 2 Slowly pull the seat belt out of the retractor and insert the tongue into the buckle until it snaps. 1-4 Safety - seats, seat belts and supplemental restraint system 3 Position the lap belt portion low on the hips as shown. 4 Pull the shoulder belt portion toward the retractor to take up extra slack. WARNING • The seat belt should rest on the middle of the shoulder. It must not rest against the neck. • Make sure that the seat belt is not twisted in any way. To release the belts To release the belt, press the button on the buckle. The seat belt will automatically retract. Chapter1.fm Page 5 Thursday, April 11, 2013 2:41 PM Checking seat belt operation Your seat belt retractors are designed to lock belt movement by two separate methods: 1 When the belt is pulled quickly from the retractor. 2 When the vehicle slows down rapidly. To increase your confidence in the belts, check the operation as follows: • Grasp the shoulder belt and pull quickly forward. The retractor should lock and restrict further belt movement. If the retractor does not lock during these checks or if you have any question about belt operation see your NISSAN Dealer. 2-POINT TYPE SEAT BELTS Fastening the seat belts 1 Insert the tongue into the buckle snaps. until it 2 To lengthen, hold the tongue at a right angle to the belt and pull on the belt. To shorten, pull the free end of the belt away from the tongue then pull the belt clip to take up the slack . Safety - seats, seat belts and supplemental restraint system 1-5 Chapter1.fm Page 6 Thursday, April 11, 2013 2:41 PM 3 Position the lap belt low on the hips illustrated. as Selecting correct set of belts Unfastening the seat belts To loosen the belt, press the button buckle. Front center belt on the The centre seat belt buckle and tongue are identified by the "CENTRE'' mark . The centre seat belt tongue can be fastened only into the centre seat belt buckle. Fasten the seat belts when not in use to prevent them from being caught in the door. 1-6 Safety - seats, seat belts and supplemental restraint system Rear center belt Chapter1.fm Page 7 Thursday, April 11, 2013 2:41 PM CHILD RESTRAINTS PRECAUTIONS ON CHILD RESTRAINTS USAGE Infants and small children should always be placed in an infant or child restraint while riding in the vehicle. • WARNING Infants and small children should never be carried on your lap. It is not possible for even the strongest adult to resist the forces of an accident. The child could be crushed between the adult and parts of the vehicle. Also, do not put the same seat belt around both your child and yourself. In general, child restraints are designed to be installed with the lap portion of a three-point type seat belt. NISSAN recommends that the child restraint system be installed in the rear seat. According to accident statistics, children are safer when properly restrained in the rear seat rather than in the front seat. • Place your child in the child restraint system and check the various • When the child restraint system is not in use, keep it secured with a seat belt to prevent it from being thrown around in case of a sudden stop or accident. Check the child restraint in your vehicle to be sure it is compatible with the vehicle’s seat belt system. • Remember that a child restraint system left in a closed vehicle can become very hot. Check the seating surface and buckles before placing your child in a child restraint system. • After attaching a child restraint system, test it before you place the child in it. Tilt it from side to side. Try to tug it forward and check if it is held securely in place. If the restraint is not secure, tighten the belt as necessary, or install the restraint in another seat and test it again. • If a child restraint system is not anchored properly, the risk of a child being injured in a collision or a collision or a sudden stop greatly increases. • Adjustable seat backs should be positioned to fit a child restraint system, but as upright as possible. • For a front-facing child restraint system, check to make sure the shoulder belt does not fit close to the child’s face or neck. If it does, put the shoulder belt behind the child restraint system. • If the seat belt in the position where a child restraint system is installed WARNING • Never install a rear-facing child restraint system in the front seat. An inflating supplemental front-impact air bag could seriously injure or kill your child. A rear-facing child restraint system must only be used in the rear seat. • Do not install a child restraint in the center position of the front bench seat. This portion is not suitable for child restraint installation. • An improperly installed child restraint could lead to serious injury in an accident. Child restraint systems specially designed for infants and small children are available from several manufacturers. When selecting any child restraint systems, keep the following points in mind: adjustments to be sure that the child restraint system is compatible with your child. Always follow the manufacturer’s instructions for installation and use. • Follow all of the child restraint system manufacturer’s instructions for installation and use. When purchasing a child restraint system, be sure to select one which will fit your child and vehicle. It may not be possible to properly install some types of child restraint systems in your vehicle. Improper use of a child restraint system can increase the risk or severity of injury for both the child and other occupants in the vehicle. Safety - seats, seat belts and supplemental restraint system 1-7 Chapter1.fm Page 8 Thursday, April 11, 2013 2:41 PM requires a locking clip and if it is not used, injuries could result from a child restraint system tipping over during normal vehicle braking or cornering. NISSAN recommends that infants and small children be seated in a child restraint system. You should choose a child restraint system that fits your vehicle and always follow the manufacturer’s instructions for installation and use. In addition, there are many types of child restraint systems available for larger children that should be used for maximum protection. 1-8 Safety - seats, seat belts and supplemental restraint system Chapter1.fm Page 9 Thursday, April 11, 2013 2:41 PM Rear facing INSTALLATION OF CHILD RESTRAINT SYSTEM Installation on bench seat Center lap belt: Secure the child restraint with the lap belt as illustrated. Remove all slack in the lap belt for a very tight fit by pulling forcefully on the lap belt adjustment. Front facing Rear facing Outboard shoulder/lap belt: Before using the locking clip, read the manufacturer’s instructions attached to the child restraint. Secure the child restraint with the lap belt as illustrated. To prevent slack in the lap belt, it will be necessary to secure the lap/shoulder belt in place with a locking clip . After attaching the child restraint, test it before you place the child in it. Tilt the restraint from side to side. If it is not secure, repeat the above procedure. Safety - seats, seat belts and supplemental restraint system 1-9 Chapter1.fm Page 10 Thursday, April 11, 2013 2:41 PM Front facing Rear facing Installation on front passenger seat (with front passenger air bag) WARNING • • Never install a rear-facing child restraint in the front passenger seat. Air bags inflate with great force. A rear-facing child restraint could be struck by the front air bag in a crash and could seriously injure or kill your child. If you install a forward-facing child restraint in the front passenger seat, place the passenger seat as far back as possible 1-10 Safety - seats, seat belts and supplemental restraint system Front facing Before using the locking clip, read the manufacturer’s instructions attached to the child restraint. Slide the seat to its rear most position. Secure the child restraint with the lap/shoulder belt as illustrated. To prevent slack in the lap belt, it will be necessary to secure the lap/ shoulder belt in place with a locking clip . A child restraint with a top strap should not be used in the front passenger seat. Chapter1.fm Page 11 Thursday, April 11, 2013 2:41 PM Rear facing Installation on front passenger seat (without front passenger air bag) Before using the locking clip, read the manufacturer’s instructions attached to the child restraint. Slide the seat to its rear most position. Secure the child restraint with the lap/shoulder belt as illustrated. To prevent slack in the lap belt, it will be necessary to secure the lap/ shoulder belt in place with a locking clip . Front facing Locking clip Use a locking clip attached to the child restraint or one which is equivalent in dimensions and strength. When your child restraint system is not in use, keep the locking clip in the glove box to prevent it from being lost. Slide the seat forward so that the seat belt fully tightens the child restraint. A child restraint with a top strap should not be used in the front passenger seat. Safety - seats, seat belts and supplemental restraint system 1-11 Chapter1.fm Page 12 Thursday, April 11, 2013 2:41 PM SUPPLEMENTAL RESTRAINT SYSTEM (AIR BAG SYSTEM) DRIVER AND FRONT AIR BAGS (if so equipped) This Supplemental Restraint System (SRS) section contains important information concerning the driver and passenger air bags. The Supplemental Restraint System Air Bag can help reduce impact force to the driver and to the front passenger in certain frontal collisions. The Air bags are designed to supplement the crash protection provided by the driver and passenger seat belts and are not a substitute for them. The seat belts should always be correctly worn and the driver and front passenger seated a suitable distance away from the steering wheel and instrument panel. (See "SEAT BELTS'' later in this section for instructions and precautions on seat belt usage.) • The seat belts and the supplemental front air bags are most effective when you are sitting back and upright in the seat. Air bags inflate with great force. If you are unrestrained, leaning forward, sitting sideways or out of position in any way, you are at greater risk of injury or death in a crash and may also receive serious or fatal injuries from the supplemental front air bag if you are up against it when it inflates. After turning the ignition key to the “ON” position, the supplemental air bag warning light illuminates. The supplemental air bag warning light will turn off after about 7 seconds if the system is operational. WARNING • The air bags ordinarily will not inflate in the event of a side impact, rear impact, roll over, or lower severity frontal collision. Always wear your seat belts to help reduce the risk or severity of injury in various kinds of accidents. 1-12 Safety - seats, seat belts and supplemental restraint system Chapter1.fm Page 13 Thursday, April 11, 2013 2:41 PM Safety - seats, seat belts and supplemental restraint system 1-13 Chapter1.fm Page 14 Thursday, April 11, 2013 2:41 PM WARNING 1-14 Safety - seats, seat belts and supplemental restraint system • Never let children ride unrestrained as shown in the illustrations. • Children may be severely injured or killed when the air bag inflates if they are not properly restrained. • Also, never install a rear facing child restraint in the front seat. For additional information, see "CHILD RESTRAINTS'' earlier in this section. Chapter1.fm Page 15 Thursday, April 11, 2013 2:41 PM Supplemental front air bags, along with the use of seat belts, help to cushion the impact force on the face and chest of the front occupants. They can help save lives and reduce serious injuries. However, an inflating air bag may cause facial abrasions or other injuries. Air bags do not provide restraint to the lower body. 1 Air bag warning lamp 2 Driver/Passenger air bag module 3 Diagnosis sensor unit Air bag system The driver air bag is located in the centre of the steering wheel; the front passenger supplemental air bag is mounted in the dashboard above the glove box. The air bags are designed to inflate in higher severity frontal collisions, although they may inflate if the forces in another type of collision are similar to those of a higher severity frontal impact. When the supplemental air bag inflates, a fairly loud noise may be heard, followed by release of smoke. This smoke is not harmful and does not indicate a fire, but care should be taken not to inhale it, as it may cause irritation and choking. Those with a history of breathing trouble should get fresh air promptly. The seat belts should be correctly worn and the driver and passenger seated upright as far as practical away from the steering wheel or dash board. Since the air bags inflate quickly in order to help protect the front occupants, the force of the air bag inflating can increase the risk of injury if the occupant is too close to, or is against the air bag module during inflation. The air bag will deflate quickly after the collision is over. After turning the ignition key to the “ON” position, the supplemental air bag warning light illuminates. The supplemental air bag warning light will turn off after about 7 seconds if the system is operational. WARNING • Right after inflation, several air bag system components will be hot. Do not touch them; you may severely burn yourself. • No unauthorised changes should be made to any components or wiring of the supplemental front air bag system. This is to prevent accidental inflation of the air bag or damage to the air bag system. • Tampering with these systems may result in serious personal injury. Tampering includes changes to the steering wheel and the instrument panel and the front seats assembly by placing material over the steering wheel pad and above the dashboard. • Do not attach any objects to the steering wheel pad and to the instrument panel. Objects attached to the steering wheel pad and to the instrument panel may become dangerous projectiles and cause injury if the air bag inflates. • An authorised NISSAN Dealer should do work around and on the supplemental front air bag systems. An authorised NISSAN Dealer should also do installation of electrical equipment. The SRS wiring harnesses* should not be modified or disconnected. Unauthorised electrical test equipment and probing devices should not be used on these systems. * SRS wiring harnesses are covered with yellow insulation either just before the harness connectors or for the complete harness, for easy identification. DRIVER AIR BAG SYSTEM This Supplemental Restraint System section contains important information concerning the driver air bag. The Supplemental Restraint System Air Bag can help reduce impact force to the driver in certain frontal collisions. The air Safety - seats, seat belts and supplemental restraint system 1-15 Chapter1.fm Page 16 Thursday, April 11, 2013 2:41 PM bag is designed to supplement the crash protection provided by the driver seat belt and is not a substitute for it. The seat belts should always be correctly worn and the driver seated a suitable distance from the steering wheel. (See “SEAT BELTS” later in this section for instructions and precautions on seat belt usage). After turning the ignition key to the “ON” position, the air bag warning light illuminates. The air bag warning light will turn off after about 7 seconds if the system is operational. WARNING • The air bag ordinarily will not inflate in the event of a side impact, rear impact, roll over, or lower severity frontal collision. Always wear your seat belts to help reduce the risk or severity of injury in various kinds of accidents. • The seat belts and the air bag are most effective when you are sitting back and upright in the seat. Air bag inflates with great force. If you are unrestrained, leaning forward, sitting sideways or out of position in any way, you are at greater risk of injury or death in a crash and may also receive serious or fatal injuries from the air bag if you are up against it when it inflates. 1-16 Safety - seats, seat belts and supplemental restraint system Chapter1.fm Page 17 Thursday, April 11, 2013 2:41 PM force on the face and chest of the front occupants. • Tampering with these systems may result in serious personal injury. Tampering includes changes to the steering wheel and the instrument panel and the front seats assembly by placing material over the steering wheel pad and above the dashboard. • Do not attach any objects to the steering wheel pad and to the instrument panel. Objects attached to the steering wheel pad and to the instrument panel may become dangerous projectiles and cause injury if the air bag inflates. • An authorised NISSAN Dealer should do work around and on the supplemental front air bag systems. An authorised NISSAN Dealer should also do installation of electrical equipment. The SRS wiring harnesses* should not be modified or disconnected. Unauthorised electrical test equipment and probing devices should not be used on these systems. They can help save lives and reduce serious injuries. However, an inflating air bag may cause facial abrasions or other injuries. Air bags do not provide restraint to the lower body. 1 Air bag warning lamp 2 Driver air bag module 3 Diagnosis sensor unit Air bag system The driver air bag is located in the centre of the steering wheel. The air bag is designed to inflate in higher severity frontal collisions, although it may inflate if the forces in another type of collision are similar to those of a higher severity frontal impact. When the supplemental air bag inflates, a fairly loud noise may be heard, followed by release of smoke. This smoke is not harmful and does not indicate a fire, but care should be taken not to inhale it, as it may cause irritation and choking. Those with a history of breathing trouble should get fresh air promptly. Supplemental front air bags, along with the use of seat belts, help to cushion the impact The seat belts should be correctly worn and the driver and passenger seated upright as far as practical away from the steering wheel or dash board. Since the air bags inflate quickly in order to help protect the front occupants, the force of the air bag inflating can increase the risk of injury if the occupant is too close to, or is against the air bag module during inflation. The air bag will deflate quickly after the collision is over. After turning the ignition key to the “ON” position, the supplemental air bag warning light illuminates. The supplemental air bag warning light will turn off after about 7 seconds if the system is operational. WARNING • Right after inflation, several air bag system components will be hot. Do not touch them; you may severely burn yourself. • No unauthorised changes should be made to any components or wiring of the supplemental front air bag system. This is to prevent accidental inflation of the air bag or damage to the air bag system. * SRS wiring harnesses are covered with yellow insulation either just before the harness connectors or for the complete harness, for easy identification. Safety - seats, seat belts and supplemental restraint system 1-17 Chapter1.fm Page 18 Thursday, April 11, 2013 2:41 PM AIR BAG WARNING LABELS (if so equipped) AIR BAG WARNING LIGHT (if so equipped) The air bag warning light, displaying or in the instrument panel, monitors the circuits of the front air bag system. The circuits monitored by the air bag warning light are the diagnosis sensor unit, front air bag modules and all related wiring. After turning the ignition key to the "ON'' position, the supplemental air bag warning light illuminates. The supplemental air bag warning light will turn off after about 7 seconds if the system is operational. Type A If any of the following conditions occurs, the front air bag system needs servicing and must be taken to your nearest authorised NISSAN Dealer: • The air bag warning light remains on after approximately 7 seconds. • The air bag warning light flashes intermittently. • The air bag light does not come on at all Under these conditions, the front air bags may not operate properly. It must be checked and repaired. Take your vehicle to the nearest authorised NISSAN Dealer. Repair and replacement procedure Warning labels about the air bag system are placed on the driver’s and/or front passenger’s side sun visors. Type B 1-18 Safety - seats, seat belts and supplemental restraint system The front air bags are designed to inflate on a one-time-only basis. As a reminder, unless it is damaged, the air bag light will remain illuminated after inflation has occurred. Only authorised NISSAN Dealers should do repair and replacement of these systems. Chapter1.fm Page 19 Thursday, April 11, 2013 2:41 PM To ensure long-term functioning, the system must be inspected 10 years after the date of manufacture and then every 2 years thereafter. PRE-TENSIONER SEAT BELT SYSTEM (if so equipped) When maintenance work is required on the vehicle, the air bag system and related parts should be pointed out to the person conducting the maintenance. The ignition key should always be in the "LOCK'' position when working under the hood (bonnet) or inside the vehicle. • The pre-tensioner seat belt cannot be reused after activation. It must be replaced together with the retractor as an unit. • If the vehicle becomes involved in certain types of frontal collision but the pre-tensioner is not activated, be sure to have the pre-tensioner system checked and if necessary, replaced by your NISSAN dealer. • No unauthorized changes should be made to any components of wiring of the pre-tensioner seat belt system. This is to prevent accidental retraction or extension of the pre-tensioner seat belt or damage to the pre-tensioner seat belt operation. Tampering with the pre-tensioner seat belt system may result in serious personal injury. WARNING WARNING • Once the air bag inflates, the air bag module will not function again and must be replaced. An authorised NISSAN Dealer should replace the air bag module. The air bag module cannot be repaired. • The supplemental front air bag and pre-tensioner seat belt should be inspected by an authorised NISSAN Dealer if there is any damage to the front-end portion of the vehicle. • When selling your vehicle, we request that you inform the buyer about the air bag system and guide the buyer to the appropriate sections in this Owner's Manual. • If you need to dispose of an air bag or scrap the vehicle, contact an authorised NISSAN Dealer. Correct air bag disposal procedures are set forth in the appropriate NISSAN Service Manual. Incorrect disposal procedures could cause personal injury. Safety - seats, seat belts and supplemental restraint system 1-19 Chapter1.fm Page 20 Thursday, April 11, 2013 2:41 PM 1-20 Safety - seats, seat belts and supplemental restraint system Chapter2TOC.fm Page 0 Tuesday, October 29, 2013 9:02 AM 2 Instruments and controls Instrument panel ...................................................................... 2-1 Right-hand drive model................................................... 2-1 Left hand drive model...................................................... 2-2 Meters and gauges ................................................................. 2-3 Speedometer and odometer ......................................... 2-6 Tachometer (if so equipped) ......................................... 2-6 Engine coolant temperature gauge.............................. 2-7 Fuel gauge ......................................................................... 2-7 Clock ................................................................................... 2-8 Warning/indicator lights and audible reminders .............. 2-9 Checking bulbs................................................................. 2-9 Warning lights................................................................... 2-9 Indicator lights.................................................................2-11 Security system (if so equipped) .......................................2-12 NATS (NISSAN Anti-Theft System) ..........................2-12 Security indicator light ..................................................2-12 Wiper and washer switch....................................................2-13 Windshield wiper and washer switch........................2-13 Headlight and turn signal switch........................................2-14 Headlight switch.............................................................2-14 Turn signal switch...........................................................2-14 Fog light switch (if equipped) .............................................2-15 Hazard indicator flasher switch ..........................................2-15 Windows..................................................................................2-16 Manual windows .............................................................2-16 Power windows (if so equipped) ................................2-16 Automatic operation.......................................................2-18 Rear sliding window (if so equipped) ........................2-18 Power Point and ashtrays (if so equipped)......................2-18 Power Point .....................................................................2-18 Ashtrays ............................................................................2-18 Interior lights ...........................................................................2-19 Storages ..................................................................................2-19 Glove box .........................................................................2-19 Cup holder (if so equipped).........................................2-19 Console box (if so equipped) ......................................2-20 Chapter2TOC.fm Page 1 Tuesday, October 29, 2013 9:02 AM Chapter2.fm Page 1 Thursday, April 11, 2013 2:45 PM INSTRUMENT PANEL 16 Tilting steering wheel lock lever* 17 Ignition switch/steering lock 18 Hood release lever 19 Heat switch* 20 Fuse box cover *: if so equipped Note: Diff Lock switch (Type A) is situated on the centre console, between the two seperate front seats. RIGHT-HAND DRIVE MODEL 8 Driver’s air bag* 9 Diff lock switch (Type B)* 1 Side ventilator 2 3 Passenger’s air bag*/instrument panel pocket* Center ventilator 4 Radio/CD* 12 Heater/Air conditioner* control 5 Hazard warning flasher switch 13 Cigarette lighter 6 Windshield wiper/washer switch 14 Ashtrays 7 Meters/gauges and clock 15 Parking brake lever (stick type)* 10 Headlight, turn signal switch & Fog light switch* 11 Glove box Instruments and controls 2-1 Chapter2.fm Page 2 Thursday, April 11, 2013 2:45 PM 15 Ignition switch/steering lock 16 Parking brake lever (stick type)* 17 Ashtrays 18 Cigarette lighter 19 Heater/Air conditioner* control 20 Glove box *: if so equipped Note: Diff Lock switch (Type A) is situated on the centre console, between the two seperate front seats. LEFT-HAND DRIVE MODEL 7 Radio/CD* 1 Headlight, Turn signal switch & Fog light 8 Hazard warning flasher switch switch* 9 Passenger’s air bag*/instrument panel pocket* 2 Diff lock switch (Type B)* 3 Driver’s air bag* 10 Side ventilator 4 Meters/gauges and clock 11 Fuse box cover 5 Windshield wiper/washer switch 12 Heat switch* 6 Center ventilator 13 Hood release lever 14 Tilting steering wheel lock lever* 2-2 Instruments and controls Chapter2.fm Page 3 Thursday, April 11, 2013 2:45 PM METERS AND GAUGES Type A Fuel gauge 5 Engine coolant temperature gauge 9 2 Speedometer 6 Warning / indicator light 10 Clock adjustment knob 3 Turn signal lights / hazard indicator lights 7 Odometer / trip odometer 11 Red zone indication / airbag warning light 8 Trip Odometer Reset knob 1 4 Clock Tachometer Instruments and controls 2-3 Chapter2.fm Page 4 Thursday, April 11, 2013 2:45 PM METERS AND GAUGES 1 Type B Fuel gauge Tachometer 7 Odometer / trip meter and clock 8 Trip meter Reset and Clock adjustment 9 Red zone indication 2 Speedometer 4 3 Turn signal lights / hazard indicator lights 5 Engine coolant temperature gauge / airbag warning light 6 Warning / indicator lights 2-4 Instruments and controls knob Chapter2.fm Page 5 Thursday, April 11, 2013 2:45 PM METERS AND GAUGES Type C Fuel gauge 4 Speedometer 7 Clock Adjustment knob 2 Warning / indicator lights 5 Engine coolant temperature gauge 8 Odometer/twin trip odometer 3 Turn signal lights / hazard indicator lights 6 Clock 9 Trip odometer reset knob 1 Instruments and controls 2-5 Chapter2.fm Page 6 Thursday, April 11, 2013 2:45 PM SPEEDOMETER AND ODOMETER TACHOMETER (if so equipped) Speedometer Changing the trip odometer display The speedometer indicates vehicle speed. Push the reset knob as follows: Odometer/Twin trip odometer The odometer records the total distance the vehicle has been driven. The trip odometer individual trips. records the distance of 2-6 Instruments and controls ODO TRIP A to change the display The tachometer indicates engine speed in revolutions per minute (r/min). Do not rev the engine into the red zone. CAUTION: TRIP B ODO Resetting the trip odometer Push the reset knob for more than 1 second to reset the displayed trip odometer to zero. When engine speed approaches the red zone, shift to a higher gear. Operating the engine in the red zone may cause serious engine damage. Chapter2.fm Page 7 Thursday, April 11, 2013 2:45 PM ENGINE COOLANT TEMPERATURE GAUGE FUEL GAUGE • If the engine is overheated, continued operation of the vehicle may seriously damage the engine. See "IF YOUR VEHICLE OVERHEATS” in the “6. In case of emergency'' section for immediate action required. WARNING Allow the engine to cool before removing the radiator cap to avoid the danger of being scalded. The gauge indicates the engine coolant temperature. The engine coolant temperature will vary with the outside air temperature and driving conditions. CAUTION: • • When towing a trailer or driving uphill, if the needle nears the hot end of the normal range, reduce the vehicle speed as soon as safely possible to decrease the engine coolant temperature. It is recommended to use 2nd and 3rd gears under speeds of 30 km/h (20 MPH) and 60 km/h (37 MPH) respectively. If the gauge indicates above the normal range, stop the vehicle as soon as safely possible. The gauge indicates the APPROXIMATE fuel level in the tank. The gauge may move slightly during braking, turning, acceleration, or going up or down hill. The gauge needle is designed to remain in approximately the same position, even when the ignition key is turned "OFF". CAUTION: Refill before the gauge registers Empty (E). Instruments and controls 2-7 Chapter2.fm Page 8 Thursday, April 11, 2013 2:45 PM CLOCK Type A Type B The digital clock displays on the meter or gauge all the time. When the ignition key is in "ON", an illumination light will come on. Adjusting the time Turn the adjusting knob advance the hour. Turn the adjusting knob advance the minute. anti-clockwise to clockwise to Once the power supply is disconnected, the clock will start to operate from the time 1:00. Adjust the time display. 2-8 Instruments and controls Type C Chapter2.fm Page 9 Thursday, April 11, 2013 2:45 PM WARNING / INDICATOR LIGHTS AND CHIMES or Low fuel warning light* High beam indicator light (blue) Seat belt warning light* Malfunction indicator light (MI or MIL) Speed [120 km/h (75 MPH)] warning light* Turn signal/hazard indicator light Brake warning light Water in fuel filter warning light (Diesel engine - YD25DDTi diesel engines only) Security indicator light* Charge warning light 4-wheel drive indicator light (TX model)* Engine oil pressure warning light Glow plug indicator light (Diesel engine) Air bag warning light* Anti-lock light* brake system warning Checking bulbs With all doors closed, apply the parking brake, fasten the seat belts and turn the ignition key to "ON'' without starting the engine. The following lights will come on: The following lights come on briefly and then go off: If any light fails to come on, it may indicate a burned-out bulb or an open circuit in the electrical system. Have the system repaired promptly. WARNING LIGHTS or Air bag warning light (if so equipped) When the ignition key is in the "ON'' or "START'' position, the air bag light will illuminate for about 7 seconds and then turn off. This means the system is operational. If any of the following conditions occur, the air bag and pre-tensioned seat belt need servicing and your vehicle must be taken to your nearest Authorized NISSAN Dealer. Diff Lock indicator light* * if so equipped • The air bag warning light remains on after approximately 7 seconds. • The air bag warning light flashes intermittently. • The air bag warning light does not come on at all. Unless checked and repaired, the Supplemental Restraint System and/or pretensioned seat belt may not function properly. For additional details on the Air Bag System, see "1. Safety - seats, seat belts and supplemental restraint system” Instruments and controls 2-9 Chapter2.fm Page 10 Thursday, April 11, 2013 2:45 PM Anti-lock brake system warning light (if so equipped) After turning the ignition key to the “ON” position, the light will illuminate. The anti-lock brake warning light will turn off after about 1 second if the system is operational. If the light comes on while the engine is running, it may indicate the anti-lock brake system is not functioning properly. Have the system checked by your NISSAN Dealer. 1 If the brake fluid level is below the MINIMUM mark on the brake fluid reservoir, do not drive until the brake system has been checked at a NISSAN Dealer. 2 If the brake fluid level is correct, have the warning system checked by a NISSAN Dealer. WARNING • Even if you judge that to continue driving is safe, have your vehicle towed because driving it could be dangerous. Pressing the brake pedal when the engine stops and / or low brake fluid level may increase your stopping distance and require greater pedal effort as well as pedal travel. However if the light illuminates while starting the engine, it does not indicate a system malfunction. If a malfunction occurs in the system, the antilock function of the brake will cease but the ordinary brakes will continue to operate normally. If the light comes on while you are driving, contact your NISSAN Dealer for repair. Brake warning light This light functions for both the parking brake and the foot brake systems. Parking brake indicator: The light comes on when the parking brake is applied. Low brake fluid warning light: equipped) (if so The light warns of a low brake fluid level. If the light comes on while the engine is running with the parking brake not applied, stop the vehicle and perform the following: 2-10 Instruments and controls Check the brake fluid level. Add brake fluid as necessary. See "BRAKE AND CLUTCH FLUID'' in the "8. Maintenance and do-ityourself'' section. WARNING • Charge warning light If the light comes on while the engine is running, it may indicate the charging system is not functioning properly. Turn the engine off and check the alternator belt. If the belt is loose, broken, missing or if the light remains on, see your NISSAN Dealer immediately. CAUTION: Do not continue driving if the belt is loose, broken or missing. Engine oil pressure warning light This light warns of low engine oil pressure. If the light flickers or comes on during normal driving, pull off the road in a safe area, stop the engine immediately and call a NISSAN Dealership. CAUTION: • Running the engine with the oil pressure warning light on could cause serious damage to the engine. • The engine oil pressure warning light is not designed to indicate a low oil level. Use the dipstick to check the oil level. See “ENGINE OIL” in the “8. Maintenance and do-it-yourself” section. Low fuel warning light (if so equipped) This light comes on when the fuel tank is almost empty. Refuel at the nearest filling station. Seat belt warning light (if so equipped) When the ignition switch is in the “ON” position, the seat belt warning light illuminates. The light will continue to illuminate until the driver’s seat belt is fastened. For models equipped with pre-tensioner seat belt (if the air bag warning light is ): When the ignition key is turned to the ON position, the seat belt warning light illuminates for about 7 seconds. If the light starts blinking after about 7 seconds, there may be something wrong with the pre-tensioner seat belt. In this case, the pre-tensioner will not Chapter2.fm Page 11 Thursday, April 11, 2013 2:45 PM operate properly. Have it checked by your NISSAN dealer. For additional information, see “PRETENSIONER SEAT BELT SYSTEM” in the “1. Safety - seats, seat belts and supplemental restraint system” section. Speed [120 km/h (75 MPH)] warning light (if equipped) This light blinks when the vehicle speed goes over approximately 120 km/h (75 MPH). Be sure to observe the speed limit in the area where you are driving. Water in fuel filter warning light (YD25DDTi diesel engines only) If the light comes on (and a chime sounds if so equipped) while the engine is running, it warns that you need to immediately drain the water from the fuel filter. See "FUEL FILTER" in the "8. Maintenance and do-it-yourself" section. CAUTION: Failure to drain water can cause serious damage to the engine. INDICATOR LIGHTS 4-Wheel drive indicator light (4X4 model) This light comes on when the transfer shift control lever is in the "4H" or "4L" position. If the light remains on when shifting from "4H" to "2H", the 2-wheel drive is not selected. Ensure safety and either accelerate, decelerate or reverse the vehicle to change to 2-wheel drive. Glow plug indicator (Diesel engines) light This light comes on when the ignition key is in "ON", and goes out when the glow plugs have been preheated. When the engine temperature is colder, the glow plug warm-up time will be longer. High beam (Blue) indicator light This light comes on when the headlight high beam is ON, and goes out when the low beam is selected. Malfunction indicator (light) (MI or MIL) (YD25DDTi diesel engine) This light functions as an indicator for the "Water in fuel filter warning (YD25DDTi diesel engine) and engine control malfunction indicator. Water in fuel filter warning (YD25DDTi diesel engine) If the light comes on while the engine is running, it may warn that you need to drain water from the fuel filter. This should be checked immediately. See “FUEL FILTER” in the “8. Maintenance and do-it-yourself” section. CAUTION: Failure to drain water can cause serious damage to the engine. Malfunction indicator light function for engine control (Gasoline and diesel engines): If this light comes on while the engine is running, it may indicate a potential engine control malfunction. Although the vehicle is still driveable, see your NISSAN dealer for service as soon as possible. You do not need to have your vehicle towed to the dealer. Continued operation without having the engine control system checked and repaired as necessary could lead to poor driveability, reduced fuel economy and possible damage tot he engine control system. Incorrect setting of the engine control system may lead to non-compliance of local and national emission laws and regulations. Security indicator light (if so equipped) The security indicator light blinks whenever the ignition is in the “ACC”, “OFF” or “LOCK” position. This function indicates that the theft warning system equipped on the vehicle is operational. If the theft warning system is malfunctioning, this light will remain on while the ignition switch is in the “ON” position. (See “SECURITY SYSTEM” later in this section for additional information.) Turn signal/hazard lights indicator The light flashes when the turn signal switch lever or hazard switch is turned on. Diff Lock indicator light (if so equipped) This light comes on when the diff lock switch is turned to the on position. Instruments and controls 2-11 Chapter2.fm Page 12 Thursday, April 11, 2013 2:45 PM SECURITY SYSTEM (if so equipped) Security indicator light If NATS (Nissan Anti-theft System) is malfunctioning, the security indicator light or will remain on while the ignition key is in the ON position. NATS (NISSAN ANTI-THEFT SYSTEM) The NATS (NISSAN Anti-theft System)* will not allow the engine to start without the use of the registered NATS key. If NATS (Nissan Anti-Theft System) is malfunctioning, the security indicator light or will turn on after flashing six times while the ignition key is in the ON position. However, if the security indicator light turns off after the light has remained on for 15 minutes, you can start the engine only once. See your NISSAN dealer for NATS service as soon as possible. * Immobiliser If the engine fails to start using the registered NATS key, it may be due to interference caused by another NATS key, an automated toll road device or automated payment device on the key ring. Restart the engine using the following procedures: 1 Leave the ignition switch in the “ON” position for approximately 5 seconds. 2 Turn the ignition switch to the “OFF” or “LOCK” position and wait approximately 5 seconds. 3 Repeat step 1 and 2 again 4 Restart the engine while keeping the device (which may have caused the interference) separate from the registered NATS key. Type A If this procedure allows the engine to start, NISSAN recommends placing the registered NATS key on a separate key ring to avoid interference from other devices. Type B 2-12 Instruments and controls If the light still remains ON and/or the engine will not start, see your NISSAN Dealer for NATS service as soon as possible. Please bring all NATS keys that you have when visiting your NISSAN Dealer for service. Chapter2.fm Page 13 Thursday, April 11, 2013 2:45 PM WINDSHIELD WIPER AND WASHER SWITCH Left-hand drive models Right-hand drive models Turn the ignition switch to "ACC" or "ON" and push the lever down for intermittent (if so equipped), low speed or high speed wiper operation. CAUTION: To operate the washer, pull the lever towards you to until the desired amount of washer fluid is spread on the windshield. The wiper will automatically operate several times. • • Do not operate the washer continuously for more than 30 seconds. Do not operate the washer if the reservoir tank is empty. WARNING In freezing temperatures the washer solution may freeze on the windshield and obscure your vision. Warm the windshield with the defroster before you wash the windshield. Instruments and controls 2-13 Chapter2.fm Page 14 Thursday, April 11, 2013 2:45 PM HEADLIGHT, DIMMER AND TURN SIGNAL SWITCH NISSAN recommends you should consult the local regulations on the use of lights. Lighting Turn the switch to the position . The front park lights, tail, license plate and instrument lights will come ON. Turn the switch to the position . Headlights will come on and all the other lights remain ON. To select the high beam, push the lever forward . Pull it back to select the low beam. Right-hand drive models Flashing headlight Pulling the lever toward you will turn ON headlight high beam even when the headlight switch is OFF. Turn signal Move the lever up or down to signal the turning direction. When the turn is completed, the turn signals cancel automatically. Lane change signal To indicate a lane change, move the lever up or down to the point where lights begin flashing. 2-14 Instruments and controls Left-hand drive models Chapter2.fm Page 15 Thursday, April 11, 2013 2:45 PM FOG LIGHT SWITCH (if equipped) HAZARD INDICATOR FLASHER SWITCH Push the switch ON to warn other drivers when you must stop or park under emergency conditions. All turn signal lights will flash. Type A FRONT FOG LIGHTS Type A: The flasher can be activated with the ignition switch either off or on. The fog light switch operates when the headlight switch is in the or position. Push the switch on to turn on the fog lights. WARNING Type B • When stalled or stopped on the roadway under emergency conditions, move the vehicle well off the road. • Do not use the switch while moving on the highway unless unusual circumstances force you to drive so slowly that your vehicle might become a hazard to other traffic. Type B: To turn the fog lights on, turn the headlight switch to the or position, then turn the fog light switch to the position . To turn them off, turn the switch to the OFF position. The headlight switch must be in the position for the fog lights to operate. or Instruments and controls 2-15 Chapter2.fm Page 16 Thursday, April 11, 2013 2:45 PM MANUAL WINDOWS • Some government laws may prohibit the use of the hazard warning flasher switch while driving. • Turn signals do not work when the hazard warning flasher switch is operating. The side windows can be opened or closed by turning the hand crank on each door. POWER WINDOWS (if so equipped) Right-hand drive models Left-hand drive models 2-16 Instruments and controls Chapter2.fm Page 17 Thursday, April 11, 2013 2:45 PM Driver’s side window switch Passenger’s side window switch The power window only operates when the ignition key is in the "ON'' position. Front passenger’s switch (Type A) or rear passenger’s switch (Type B) (Double cab models) will open or close only the corresponding window. To open or close the window, push down or pull up the switch and hold it. To open or close the window, push down or pull up the switch and hold it. The main switch to the driver’s side door will open or close each window by operating the driver side switch , front passenger side switch , rear right side switch (Double cab models) and rear left side switch (Double cab models) . Locking passenger's window (if so equipped) If the passenger’s window lock button on the driver’s side switch is pushed in, the passenger’s side switch cannot be operated. Type A When the lock button is pushed in, only the driver side window can be opened or closed. Push it in again to cancel. For the power door lock switch descriptions, refer to “LOCKING WITH POWER DOOR LOCK SWITCH” in the “3. Pre-driving checks and adjustments” section. WARNING • Make sure that the passenger has his/her hands etc. inside the vehicle before closing the windows. • Do not leave children and pets unattended inside the vehicle. They could unknowingly activate switches. Type B Instruments and controls 2-17 Chapter2.fm Page 18 Tuesday, October 29, 2013 8:53 AM POWER POINT AND ASHTRAYS (if so equipped) Automatic operation (if so equipped) Rear sliding window (if so equipped) To fully open or close (if so equipped) the driver’s side window, completely push down or pull up the switch and release it; it need not be held. The window will automatically open or close all the way. To stop the window, just press the switch in the opposite direction. Pull the lever toward window . and then slide the The power socket operates when the ignition switch is in the "ACC'' or "ON'' position. Remove the power outlet cap to access the socket for personal accessories. Return the power outlet cap to its original position after use. To take out the ashtray, push down the holding part as illustrated. Front ashtrays are located on the console panel. 2-18 Instruments and controls Chapter2.fm Page 19 Thursday, April 11, 2013 2:45 PM INTERIOR LIGHTS GLOVE BOX WARNING Keep glove box lid closed while driving to prevent injury in an accident or a sudden stop. CUP HOLDERS (If so equipped) WARNING • The interior light has a three-position switch. • • • Type A When the switch is in the centre "O"' or “DOOR” position , the light will illuminate by opening the doors. When the switch is in the "OFF" position, the interior light will not illuminate, regardless of door position. When the switch is in the "ON" position , the interior light will illuminate, whether any door is opened or closed. The driver should not pull out the cup holder or remove or insert cups into the cup holder while driving in order that full attention may be given to the driving operation. CAUTION: • Avoid abrupt starting and braking when the cup holder is being used to prevent spillage. If the liquid is hot, it can scald you or your passenger. CAUTION: Do not use for extended periods of time with the engine stopped. Type B To open the glove box lid, pull the lever up . The glove box can be locked or unlocked with the ignition key if the lid is equipped with a key cylinder. Instruments and controls 2-19 Chapter2.fm Page 20 Thursday, April 11, 2013 2:45 PM CONSOLE BOX (If so equipped) Type B WARNING • • Type A Pull the right side lever lid to open the lid only. on the console box Pull the left side lever on the console box lid to open the lid with the cup holder. Do not place valuable items in the storage. 2-20 Instruments and controls The centre console box should not be used while driving in order that full attention may be given to the driving operation. Keep the console box and glove box lid closed while driving to prevent injury in an accident or a sudden stop. CAUTION: Do not place valuable items in the centre console box. Chapter3TOC.fm Page 0 Thursday, April 11, 2013 2:47 PM 3 Pre-driving checks and adjustments Keys ............................................................................................ 3-1 NATS (NISSAN Anti-Theft System) (if so equipped)................................................................. 3-2 Door locks ................................................................................. 3-2 Locking with key ............................................................... 3-2 Locking with inside lock knob ....................................... 3-2 Locking with power door lock switch (if so equipped)................................................................. 3-3 Child safety rear door lock (Double cab models) ..... 3-3 Remote control door lock system (if so equipped)........................................................................ 3-4 Locking doors ................................................................... 3-5 Unlocking doors................................................................ 3-5 Battery replacement ........................................................ 3-5 Hood........................................................................................... 3-6 Opening the hood ............................................................ 3-6 Closing the hood.............................................................. 3-6 Fuel filler lid ............................................................................... 3-7 Tailgate latch............................................................................. 3-8 Tailgate ............................................................................... 3-9 Tie down hooks (if so equipped) .................................. 3-9 Roof luggage rack .................................................................3-10 Steering wheel .......................................................................3-10 Tilting steering wheel (if so equipped) ......................3-10 Mirrors ......................................................................................3-10 Outside rearview mirrors...............................................3-10 Inside rearview mirror ....................................................3-11 Vanity mirror (if so equipped) ......................................3-12 Parking brake ..........................................................................3-12 Stick Type ........................................................................3-12 Center lever type ............................................................3-12 Chapter3TOC.fm Page 1 Thursday, April 11, 2013 2:47 PM Chapter3.fm Page 1 Friday, April 12, 2013 9:07 AM KEYS Type A Type B Type C The key can only be inserted fully in the ignition key cylinder. For the door, glove box and fuel filler lid key cylinders, it is normal for the key not to go into the key cylinder all the way. A key number plate is supplied with your key. Record the key number and keep the plate in a safe place (such as your wallet), NOT IN THE CAR. NISSAN does not record key numbers so it is very important to keep track of your key number plate. Type D A key number is only necessary when you have lost all keys and do not have one to duplicate from. If you still have a key, this key can be duplicated by your NISSAN dealer. CAUTION: Do not leave the ignition key inside the vehicle if you leave the vehicle. Pre-driving checks and adjustments 3-1 Chapter3.fm Page 2 Friday, April 12, 2013 9:07 AM DOOR LOCKS NATS (Nissan Anti-theft System)* if so equipped Only a key with NATS can start your vehicle. A key number and NATS PIN code are necessary when you need an extra key made. Type A: As many as 5 keys with NATS can be used with one vehicle. (4 door lock remote controllers can be registered for the NATS keys.) Type B: As many as 4 keys for RHD models or 5 keys for LHD models of NATS can be used with one vehicle. The new key must be registered to the NATS components of your vehicle by your NISSAN Dealer. At this time, you are requested to bring all NATS keys that you have to your NISSAN dealer. Also bring your NATS PIN code that was originally supplied with your vehicle (if so equipped). This is because the registration process will erase all memory of the NATS components. CAUTION: Do not allow the NATS key, which contains an electrical transponder to come into contact with salt water. This could affect system function. *Immobilizer 3-2 Pre-driving checks and adjustments LOCKING FRONT DOORS WITH KEY To lock the doors, turn key towards the front of the vehicle . To unlock, turn it towards the rear . Locking or unlocking the driver's door will simultaneously lock or unlock the other doors. (With power door lock models). LOCKING WITH INSIDE LOCK KNOB LOCK UNLOCK Driver's door The driver's door cannot be locked from the outside without a key . This is to prevent the door lock from accidentally being locked with the key inside the vehicle. Other doors To lock the door from the outside without a key, move the inside lock knob to the "LOCK'' position , then close the door. Chapter3.fm Page 3 Friday, April 12, 2013 9:07 AM WARNING • When locking the door without a key, be sure not to leave the key inside the vehicle. • Before opening the door, always check for and avoid oncoming traffic. • Never leave children unattended in a vehicle, and always be sure you have your keys with you when leaving your vehicle unattended. If an emergency occurs it will be difficult to help them. LOCKING WITH POWER DOOR LOCK SWITCH (if so equipped) The power door lock system allows you to lock or unlock all doors simultaneously. • Turning the driver side door key will lock or unlock all doors. • Pushing the driver's inside lock knob will lock all doors. Pulling the lock knob will unlock all doors. • Operating the power door lock switch will lock or unlock all doors except the driver side door. CHILD SAFETY REAR DOOR LOCK (Double cab models) Child safety locking helps prevent doors from being opened accidentally, especially when small children are in the vehicle. When the lever is in the LOCK position , the rear door can be opened only from the outside. For normal operation, set the lever to the FREE position . Pre-driving checks and adjustments 3-3 Chapter3.fm Page 4 Friday, April 12, 2013 9:07 AM REMOTE CONTROL DOOR LOCK SYSTEM (if so equipped) The remote keyless entry system can operate all door locks using the remote controller. The remote controller can operate at a distance of approximately 1 m (3.3 ft) from the vehicle. (The effective distance depends upon the conditions around the vehicle.) As many as four remote controllers can be used with one vehicle. For information concerning the purchase and use of additional remote controllers, contact your NISSAN Dealer. The remote controller will not function under the following conditions: • When the distance between the remote controller and vehicle is more than approximately 1 m (3.3 ft). • When te remote controller battery is discharged. • When the key is in the ignition switch. CAUTION: • When locking the doors using the remote controller, be sure not to leave the key in the vehicle. • Do not allow the remote controller, which contains electrical components, to come in contact with water or salt water. This could affect the system function. • Do not drop the remote controller. • Do not strike the remote controller sharply agains another object. 3-4 Pre-driving checks and adjustments • Do not place the remote controller for an extended period in an area where temperature exceed 60°C (140°F). If a remote controller is lost or stolen, NISSAN recommends erasing the ID code of that controller. This will prevent the controller from unauthorised use to unlock the vehicle. For information regarding the erasing procedure, contact a NISSAN dealer. If your vehicle is equipped with a genuine NISSAN Anti-Theft System, operating the remote control door lock system will simultaneously operate the anti-theft system. Type A LOCK button UNLOCK button Chapter3.fm Page 5 Friday, April 12, 2013 9:07 AM LOCKING DOORS • 1 Remove the ignition key. 2 Close all the doors. 3 Push the LOCK button controller. on the remote To replace the battery: 1 Remove the screw. 4 Operate the door handles to confirm that the doors have been securely locked. • All the doors will lock. • The hazard indicator flashes once. 2 Insert a small screw driver into the slit of the corner and twist it toseparate the upper part from the lower part. Use a cloth to protect the casing. 3 Replace the battery with a new one. When the LOCK button is pushed with all doors locked, the hazard indicator flashes once as a reminder that the doors are already locked. Recommended battery: CR1620 or equivalent. CAUTION: After locking the doors using the remote controller, be sure that the doors have been securely locked by operating the door handles. UNLOCKING DOORS 1 Push the UNLOCK button remote controller once. • All doors will unlock. • The hazard indicator flashes twice. There is danger of explosion if lithium battery is incorrectly replaced. Replace only with the same or equivalent type. on the Type A BATTERY REPLACEMENT (Type A) CAUTION: • Be careful not to allow children to swallow the battery and removed parts. • An improperly disposed battery can harm the environment. Always confirm local regulations for battery disposal. • When changing batteries, do not let dust or oil get on the components • Do not touch the internal circuit and electric terminals as doing so could cause a malfunction. • Hold the battery by the edges. Holding the battery across the contact points will seriously deplete the storage capacity. • Make sure that the + side faces the bottom case. 4 Close the lid securely and install the screw. 5 Operate the buttons to check its operation. See a NISSAN dealer if you need any assistance for replacement. Pre-driving checks and adjustments 3-5 Chapter3.fm Page 6 Friday, April 12, 2013 9:07 AM HOOD CAUTION: Always hold the battery by the edges, as shown. Holding the battery across the contact points will seriously deplete the storage capacity. OPENING THE HOOD CLOSING THE HOOD 1 Pull the hood lock release handle located below the instrument panel; the hood will then lift up slightly. When closing the hood, reset the support rod to its original position, then slowly close the hood and make sure it locks into place. 2 Pull the lever upward at the front of the hood with your fingertips and raise the hood. 3 Insert the support rod into the slot on the under-side of the hood. 3-6 Pre-driving checks and adjustments WARNING Always check that the hood is closed and locked securely to prevent it from opening while driving. The vehicle should only ever be operated with the hood securely closed. Chapter3.fm Page 7 Friday, April 12, 2013 9:07 AM FUEL FILLER LID AND CAP Type A Type B Type C To open the fuel filler lid, turn the key clockwise . To lock, close it and turn the key anti-clockwise . To open the fuel filler lid, slide the opener switch . To lock, close the fuel filler lid securely. To fill with fuel, turn the fuel filler cap anticlockwise . Turn the fuel filler cap counterclockwise and place the cap on the cap holder while filling the fuel. To open the fuel filler lid, push the opener . located on the right hand side of the driver seat, downwards. To lock, close the fuel filler lid securely. The fuel filler cap is a screw-on ratcheting type. Tighten the cap clockwise until more than 2 ratcheting clicks are heard. The cap will lock automatically. The fuel filler cap is a screw-on ratcheting type. After refueling, tighten the cap clockwise until more than 2 ratcheting clicks are heard. Turn the fuel filler cap counterclockwise and place the cap on the cap holder while filling the fuel. The fuel filler cap is a screw-on ratcheting type. After refueling, tighten the cap clockwise until more than 2 ratcheting clicks are heard. Pre-driving checks and adjustments 3-7 Chapter3.fm Page 8 Friday, April 12, 2013 9:07 AM TAILGATE LATCH WARNING • Fuel is extremely flammable and highly explosive under certain conditions. Always stop engine and do not smoke or allow open flames or sparks near the vehicle when refueling. • Fuel may be under pressure. Turn the cap one-half turn and wait for any "hissing'' sound to stop, to prevent fuel from spraying out and possible personal injury. • Use only a genuine NISSAN fuel filler cap as a replacement. It has a built-in safety valve needed for proper operation of the fuel system and emission control system. An incorrect cap can result in a serious malfunction and possible injury. • If fuel is spilled on the vehicle body, flush it away with water to avoid paint damage. To open the tailgate, pull the tailgate handle and lower the tailgate. The support stays/cables will hold the gate open. • 3-8 Pre-driving checks and adjustments Type B Type A The weight of the cargo loads must be evenly distributed over both the front and the rear axles. • All cargo should be securely fastened with ropes or straps to prevent it from shifting or sliding within the vehicle. • Do not unhook cables as the tail gate will be damaged by the bumper • When closing the tailgate, make sure that the latches are securely locked (Type A) or the handles are firmly fastened (Type B). Chapter3.fm Page 9 Friday, April 12, 2013 9:07 AM TIE DOWN HOOKS (If so equipped) Type A Releasing the tailgate stays/cables (Models without rear step bumper) To fold the tailgate down to the lowest position, lift the tailgate slightly , then release the stays/cables . CAUTION: Do not drive the vehicle with the tailgate down. Do not drop the tailgate down when a bumper or towbar is fitted. The tailgate will be damaged. For your convenience, tie down hooks are placed at each corner of the load box. These may be used to help secure cargo loaded into the load box. • The weight of the cargo load must be evenly distributed over both the front and rear axles. • All cargo should be securely fastened with ropes or straps to prevent it from shifting or sliding within the vehicle. WARNING Type B While driving, never allow anyone to ride in the cargo area. Abrupt braking or stopping could lead to personal injury. Pre-driving checks and adjustments 3-9 Chapter3.fm Page 10 Friday, April 12, 2013 9:07 AM ROOF LUGGAGE RACK (If so equipped TILTING STEERING WHEEL (if so equipped) OUTSIDE MIRROR CONTROL Push the lock lever down and adjust the steering wheel up or down to the desired position. Push the lock lever up firmly to lock the steering wheel in place. Remote control type (if so equipped) The roof rack may be used to load additional luggage on the vehicle. CAUTION • Overloading of the roof rack can cause serious damage to the vehicle. The maximum load that can be placed on the roof rack is 50 kg. • A maximum recommended speed of 120 km/h should not be exceeded when objects are loaded on the roof rack. • Always ensure that the load properly secured to the roof rack. • Keep the height of the load as small as possible, as the increased centre of gravity can have an adverse effect on the stability of the vehicle. • is If at all possible, only use the roof rack when there is no space left in the loadbox. NISSAN is not responsible for any damage to the vehicle or loss of property that may result from not adhering to these warnings. 3-10 Pre-driving checks and adjustments WARNING Do not adjust the steering wheel while driving. The outside mirror will operate only when the ignition switch is in the “ACC” or “ON” position. Push the right or left end of the switch to select the right or left side mirror, then adjust using the control knob. WARNING • Check the position of all mirrors before driving. Altering their position while driving could distract your attention from the driving operation. Chapter3.fm Page 11 Friday, April 12, 2013 9:07 AM INSIDE REARVIEW MIRROR Manually adjusting type Folding The outside mirrors can be moved in any direction for a better rear view. Push the door mirror backward to fold. Manual anti-glare type (if so equipped) The night position will reduce glare from the headlights of vehicles behind you at night. Select the day position when you drive in the daytime. CAUTION Use the night position only when necessary, because it reduces rear view clarity. Pre-driving checks and adjustments 3-11 Chapter3.fm Page 12 Friday, April 12, 2013 9:07 AM VANITY MIRROR (if so equipped) To use the front vanity mirror, pull down the passenger’s sunvisor. PARKING BRAKE LEVER Center Lever Type Stick Type To apply: pull the lever out . To release: pull out slightly and turn the lever (Left-hand drive models) or (Right-hand drive models), then push it in completely. Before driving, be sure the parking brake warning light goes out. 3-12 Pre-driving checks and adjustments To apply: pull the lever up . To release: pull the lever up slightly, push the button and lower completely. Before driving, be sure the parking brake warning light goes out. Chapter4TOC.fm Page 0 Thursday, April 11, 2013 2:48 PM 4 Heater and air conditioner and audio system Ventilators.................................................................................. 4-1 Heater and air conditioner..................................................... 4-2 Heater and manual air conditioner............................... 4-2 Servicing air conditioner................................................. 4-5 Heat switch (for YD25DDTi engine models only) .... 4-5 Driving in dusty conditions............................................. 4-5 Audio system (if so equipped).............................................. 4-6 Audio operation precautions ......................................... 4-6 Antenna............................................................................... 4-6 CD Player/LW-MW-FM Radio Type................................... 4-7 FM-AM Radio with Compact Disc (CD) Player..............4-14 Car phone and CB radio......................................................4-18 Chapter4TOC.fm Page 1 Thursday, April 11, 2013 2:48 PM Chapter4.fm Page 1 Thursday, April 11, 2013 2:47 PM CENTRE AND SIDE VENTILATORS Driver’s side Center Passenger’s side Open or close (if so equipped), and adjust the air flow direction of the ventilators. Heater and air conditioner and audio system 4-1 Chapter4.fm Page 2 Thursday, April 11, 2013 2:47 PM HEATER AND AIR CONDITIONER - Air flows from centre and ventilators and foot outlets. side - Air flows mainly from foot outlets. - Air flows from defroster outlets and foot outlets. - Air flows mainly from defroster outlets. Temperature control lever Temperature control lever allows you to adjust the temperature of the outlet air. Right hand drive WARNING • • • The air conditioner cooling function operates only when the engine is running. Do not leave children or adults who would normally require the support of others alone in your vehicle. Pets should not be left alone either. On hot, sunny days, temperatures in a closed vehicle could quickly become high enough to cause severe or possibly fatal injuries to people or animals. Do not use the re-circulation mode for long periods as it may cause the interior air to become stale and the windows to fog up. Air intake lever Left hand drive • Position of the heating or air conditioning controls should not be done while driving, so full attention may be given to vehicle operation. Fan control lever Fan control lever turns the fan on and off and controls fan speed. Air flow control lever 4-2 Heater and air conditioner and audio system - Air flows from ventilators. • position Outside air is drawn into the passenger compartment. CONTROLS Air flow control lever the air flow outlets. Air intake lever allows you to select the outside air circulation or the air recirculation. allows you to select centre and side Use this position for normal heater, or air conditioner operation. If dust is not raised in front of the vehicle, this position is effective to prevent dust entry. • position Interior air is re-circulated inside the vehicle. Move the air intake lever to this position when driving on a dusty road or to avoid traffic fumes. Chapter4.fm Page 3 Thursday, April 11, 2013 2:47 PM Air conditioner button (If so equipped) Ventilation Air conditioner button is provided only for vehicles with an air conditioner. Start the engine, move the fan control lever to the desired (1 to 4) position and push the air conditioner button to turn on the air conditioner. The indicator light will come on when the air conditioner button is on. To stop the air conditioner, push the switch again to return it to the original position. HEATER OPERATION This mode is used to direct hot air from the floor outlets. to the " 2 Move the air control lever position. to the " 3 Turn on the fan control lever . "position. 2 Move the air control lever position. to the " 3 Turn on the fan control lever . 4 Move the temperature control lever the desired position. " to " 2 Move the air control lever position. to the " 3 Turn on the fan control lever . " position. Be sure to turn the air intake lever to the " position for normal heating. This mode is used to defrost/defog the windows. 1 Move the air intake lever position. For quick heating, move the air intake lever to the " " to the " 4 Move the temperature control lever to the desired position between the middle and the "HOT'' position. • 1 Move the air intake lever Defrosting or defogging Heating 1 Move the air intake lever position for normal heating. • This mode directs outside air from the side and centre vents. " to the " " To quickly remove ice from the windows, move the air intake lever to the " " position, the fan control lever to "4'' and the temperature control lever to the full "HOT''. As soon as possible after the window is clear, move the air intake lever to the " Bi-level heating This mode directs outside air from the side and centre vents and hot air from the floor outlets. 1 Move the air intake lever position. to the " 2 Move the air control lever position. to the " 3 Turn on the fan control lever . " " 4 Normally move the temperature control lever to the midpoint between "HOT'' and "COLD''. Heating and defogging " 4 Move the temperature control lever to the desired position between the middle and the "HOT'' position. • If it is difficult to defrost the windscreen while the air conditioner is turned off, turn it on (if so equipped). This mode heats the interior and defogs the windscreen. 1 Move the air intake lever position. to the " " 2 Move the air control lever position. to the " '' 3 Turn on the fan control lever . 4 Move the temperature control lever to the desired position between the middle and the "HOT'' position. " position. Heater and air conditioner and audio system 4-3 Chapter4.fm Page 4 Thursday, April 11, 2013 2:47 PM Operating tips Clear snow and ice from the wiper blade and air inlet in front of the windshield. This will improve heater operation and defroster operation. AIR CONDITIONER OPERATION (If so equipped) A visible mist may be seen coming from the ventilators in hot, humid conditions as the air is cooled rapidly. This does not indicate a malfunction. The air conditioner cooling function operates only when the engine is running. Cooling 2 Move the air control lever position. to the " 3 Turn on the fan control lever . 4 Push in the air conditioner button indicator light will come on. to For quick cooling when the outside temperature is high, move the air intake lever to the position. Be sure to to the Dehumidified heating 1 Move the air intake lever position. to the " 2 Move the air control lever position. to the " 3 Turn on the fan control lever . 4 Push in the air conditioner lever indicator light will come on. '' . The 5 Move the temperature control lever the desired position. to This mode is used to defog the windows and dehumidify. '' 1 Move the air intake lever position. to the " 2 Turn the air control lever position. to the " 3 Turn on the fan control lever . 4-4 Heater and air conditioner and audio system " '' . The 5 Move the temperature control lever the desired position. to Operating tips • Keep windows closed while conditioner is in operation. • After parking in the sun, drive for two or three minutes with the windows open to vent hot air from the passenger compartment. Then close the windows. This will allow the air conditioner to cool the interior more quickly. • The air conditioning system should be operated for about ten minutes at least once a month, especially in winter. This helps prevent damage to the system due to lack of lubrication. • If the coolant temperature gauge exceeds the "HOT'' position, turn the air conditioner off. Have your vehicle inspected by a NISSAN Dealer. See "IF YOUR VEHICLE OVERHEATS'' in the "6. In case of emergency'' section for additional information. " " . The 4 Push in the air conditioner button indicator light will come on. This mode is used to heat and dehumidify. Dehumidified defogging This mode is used to cool and dehumidify. to the " • return the air intake lever position for normal cooling. Start the engine, move the fan control lever to the desired (1 to 4) position and push in the air conditioner button to activate the air conditioner. When the air conditioner is on, cooling and dehumidifying functions will be added to the heater operation. 1 Move the air intake lever position. 5 Move the temperature control lever the desired position. the air Chapter4.fm Page 5 Thursday, April 11, 2013 2:47 PM SERVICING AIR CONDITIONER DRIVING IN DUSTY CONDITIONS The air conditioning system in your vehicle is charge with a refrigerant designed with the environment in mind. When driving in dusty conditions: • Close all the windows. This refrigerant will not harm the earth’s ozone layer. • Move the air intake lever position. to the However, special charging equipment and lubricant are required when servicing your NISSAN air conditioner. Using improper refrigerants or lubricants will cause severe damage to your air conditioning system. See “RECOMMENDED AIR CONDITIONER SYSTEM REFRIGERANT AND LUBRICANT” in the “9. Technical information” section. • Turn on the fan control lever . This will prevent dust from entering the vehicle. When approaching a dust cloud: • HEAT SWITCH (YD25DDTi engine models only) The heat switch is found on the driver side on the lower side of the instrument panel. Move the air intake lever position. to the Once clear of the dust cloud, move the air intake lever to the position. The heat switch is used when the engine is cold to speed up the heater’s operation. If the switch is turned to the ON position and the indicator illuminates, the engine electronic control unit will automatically increase the cold engine idle speed. The system works with the transmission in the N (neutral) position (manual transmission) and the accelerator off. Turn the switch off when the engine coolant temperature gauge moves. When the vehicle is being driven, the system is automatically deactivated. Heater and air conditioner and audio system 4-5 Chapter4.fm Page 6 Thursday, April 11, 2013 2:47 PM AUDIO SYSTEM (if so equipped) • Do not expose the CD to direct sunlight. AUDIO OPERATION PRECAUTIONS • CD’s that are of poor quality, dirty, scratched or covered with finger prints, or that have pin holes may not work properly • The following CD’s may not work properly. WARNING Do not adjust the audio system while driving so that full attention may be given to vehicle operation. The audio system operates when the ignition switch is in the “ACC” or “ON” position. Radio • • Radio reception is affected by station signal strength, distance from radio transmitter, buildings, bridges, mountains and other eternal influences. Intermittent changes in reception quality normally are caused by these external influences. Using a cellular phone in or near the vehicle may influence radio reception quality. Compact Disc (CD player) • During cold weather or rainy days, the player may malfunction due to the humidity. If this occurs, remove the CD and dehumidify or ventilate the player completely. • The player may skip while driving on rough roads. • The CD player sometimes may not function when the compartment temperature is extremely high. Decrease the temperature before use. - Copy control compact discs (CCCD) - Recordable compact discs (CD-R) - Rewritable compact discs (CD-RW) • Do not use the following CD’s as they may cause the CD player to malfunction. - 8 cm (3.1 in) discs with an adapter - Discs with/without an adapter - CD’s that are not round - CD’s with a paper label - CD’s that are wrapped, scratched or have unusual edges. ANTENNA Manual antenna Adjust the antenna length for the best reception. A fully extended antenna is usually best for distant reception. CAUTION: Be sure to retract the antenna before washing the car in an automatic car wash or the antenna may be damaged. 4-6 Heater and air conditioner and audio system Chapter4.fm Page 7 Thursday, April 11, 2013 2:47 PM CD PLAYER/LW-MW-FM RADIO TYPE Anti-theft system (without personal code) This unit can only be activated when the ignition key for NATS is in the ACC or ON position. Anti-theft code) system (With personal By using a personal 4-digit code known only to the vehicle owner, the possibility of the audio unit being stolen is effectively reduced, because without the code, the unit can not be activated. When used normally, the unit is unlocked and accessible in the usual way. MUTE button 11 SEEK/TRACK button 2 POWER ON/OFF button 12 MIX (Mix play) button 3 Sound preference button 13 RPT button 4 CD button 14 VOLUME control/MENU select dial 5 FM band select button 15 ENTER button 6 Radio memory buttons 16 DISP (Display) button 7 AM band select button 17 NEWS button 8 TA (Traffic Announcement) button 18 TUNE/SEARCH button 9 MENU button 1 10 CD EJECT button If however, force is used to try and remove the unit, the anti-theft system activates and the unit locks. The only way it can be unlocked is by entering the personal code number known only by the owner. This code number cannot be altered and applies only to your vehicle. This code number is shown on a radio pass card. The radio pass card is installed in the glove box at the vehicle productions site. Ask your NISSAN dealer for the location of your radio pass card. WARNING Keep the radio pass card in a safe place and refrain from keeping it in the vehicle. Contact your NISSAN dealer if you loose the radio pass card or forget the code number of your radio. Heater and air conditioner and audio system 4-7 Chapter4.fm Page 8 Thursday, April 11, 2013 2:47 PM (CODE IN is displayed). If the above is repeated 17 times, the unit will lock permanently and you will need to contact your NISSAN dealer. Unlocking the unit: CAUTION: Read this section very carefully. It is important that the instructions are followed precisely. If the battery supply to the vehicle is interrupted by accident for some reason, the unit will lock. To unlock the unit, proceed as follows: 1 Press the power ON/OFF button to turn the unit on. 2 CODE IN is displayed. 3 Press the TUNE/SEARCH TRACK button. or The audio system operates when the ignition switch is in the “ACC” or “ON” position. POWER ON/OFF button: To turn on the audio system push the POWER ON/OFF button. • SEEK/ • 4 Input your personal code by pressing the radio memory buttons 1 to 4 (thousands digit to ones digit). 5 Press the TUNE/SEARCH TRACK button. Audio main operation or SEEK/ 6 If the entered code number is correct, the radio turns on. A radio frequency appears on the display. 7 If the entered code is incorrect, the unit becomes inoperable for 10 seconds for the first three attempts, then the code input mode is automatically set (CODE IN is displayed). 8 If the code is incorrect the fourth time, the unit becomes inoperable for 60 minutes and (- - - -) is displayed. After 60 minutes, the code input mode is automatically set The system will turn on in the mode, (radio or CD) which was used immediately before the system was turned off. If there is no CD loaded, the radio will be turned on. To turn off the audio system, push the POWER ON/OFF button. Volume control: To control the volume, turn the VOLUME control dial. Turn the VOLUME control dial to make the sound louder. Turn the VOLUME control dial counterclockwise to mae the sound quieter. Sound preference button: To enter the audio mode (radio or CD), push the button. When no CD is loaded, the audio system will automatically switch to the radio mode. 4-8 Heater and air conditioner and audio system To change the audio settings (BASS, TREBLE, FADER, BALANCE, EQ), push the button or ENTER button to select the mode. BASS EQ TREBLE BASS BALANCE FADER To adjust each audio setting, turn the MENU/ VOL control dial clockwise or counterclockwise. BASS: (-) to decrease / (+) to increase TREB(LE): (-) to decrease / (+) to increase BAL(ANCE): (R) to right balance / (L) to left balance FADE(R): (F) to front fade / (R) to rear fade EQ (Equalizer): Use this control to change the preset sound mode for CD play. Turn the MENU/VOL dial clockwise or counterclockwise. The mode will change as follows: OFF LIVE ENHANCE OFF ACOUSTIC If the audio settings mode is unchanged for approximately 8 seconds, the audio settings mode will automatically return to the normal mode. Chapter4.fm Page 9 Thursday, April 11, 2013 2:47 PM Mute button: CD button: Push the MUTE button to mute the audio system and MUTE appears on the display. To unmute, use any one of the following options: When the button is pushed while the audio system is off and a CD is loaded, the audio system will turn on and a CD will start playing automatically. If the radio is already playing, it will automatically turn off and the CD will start playing. - Push the MUTE button again. - Turn the MENU/VOL dial. - Push the CD, FM or AM button. TRACK UP/ CD player operation The audio system operates when the ignition switch is in the “ACC” or “ON” position. Loading: Insert a CD into the slot with the label side facing up. The CD will be guided automatically into the slot and will start playing. If the radio is already playing, it will automatically turn off and the CD will start playing. CAUTION: DOWN button: When the button is pushed wile a CD is being played, the present track will be advanced and move to the next track. Push the button several times to skip forward tracks. The CD will advance the number of times the button is pushed. When the last track of the CD is forwarded, the first track will be played. When the button is pushed while a CD is being played, the present track will start over from the beginning. Push the button several times to skip back tracks. The CD will rewind the number of times the button is pushed. When the first track of the CD is rewound, the last track will be played. Do not force the CD into the slot. This could damage the player. Repeat/MIX button (Type A): After loading the CD, the number of tracks and the playtime will appear on the display. Push the button repeatedly to change the play mode as follows: 8 cm (3.1 in) diameter CDs can be played without using an adapter. RPT (REPEAT) TRACK (REPEAT) ALL MIX DISC RPT Heater and air conditioner and audio system 4-9 Chapter4.fm Page 10 Thursday, April 11, 2013 2:47 PM RPT ALL: RPT TRACK: The CD player plays the current track continuously. RPT ALL: All the tracks on the CD will be played in sequential order. MIX DISC: All the tracks on the CD will be played in a random order. Repeat button: Push the button repeatedly to change the play mode as follows: RPT (REPEAT) TRACK RPT (REPEAT) ALL RPT (REPEAT) TRACK All the tracks on the CD will be played in sequential order. CD EJECT button: When the button is pushed while a CD is loaded, the CD will be ejected. When the button is pushed twice, the CD will be ejected further and the CD can be removed with ease. If a CD is ejected by pushing the button and it is not taken out from the loading slot, the CD will automatically be reloaded to the slot to protect the CD. LW-MW-FM radio operation The audio system operates when the ignition switch is in the “ACC” or “ON” position. RPT TRACK: The CD player plays the current rack continuously RPT ALL: All the tracks on the CD will be played in sequential order. MIX button: Push the button repeatedly to change the play mode as follows: MIX DISC RPT ALL MIX DISC FM-AM button: When the or button is pushed while the audio system is off, the audio system will turn on and the radio will turn on. when the or button is pushed while CD is already operating, it will automatically turn off and the radio will turn on. To change the radio bands, push the or button until the desired band appears. • FM 1 MIX DISC: All the tracks on the CD will be played in a random order 4-10 Heater and air conditioner and audio system For FM • FM 2 FM T For AM MW LW MW Chapter4.fm Page 11 Thursday, April 11, 2013 2:47 PM During FM reception, when the button is pushed for longer than 1.5 seconds, stations are searched for and the 6 stations of the FM T band. The sound is muted until the auto store operation is completed, upon which preset channel 1 is automatically tuned in. TUNE button: When adjusting the broadcasting station frequency manually, push the button. until the desired frequency is achieved. The frequency changes in steps of 100 kHz on the FM band, 9 kHz on the MW band and 3 kHz on the LW band. SEEK button: When adjusting the broadcasting station frequency automatically, push the button. When the system detects a broadcasting station, it will stop at the station. 2 Push and hold a radio memory button until a beep sounds. (The radio mutes when the memory button is pushed.) 4 Perform steps 1 - 3 for all other memory buttons. If the battery cable is disconnected, or if the audio fuse blows, the radio memory will be erased. In such a case, reset the desired stations. • DISP: When the button is pushed, the display switches between FM station frequencies and PS name. Alternative Frequency (AF): • The AF function operates in the FM (radio and CD models. The audio system can store up to 18 FM station frequencies (six in each of FM 1, FM 2 and FM T), 6 MW nd 6 LW station frequencies. • When the AF mode is set to “ON” in the user setup menu mode, the AF indicator illuminates. To store the station frequency manually: 1 Tune to the desired broadcasting station frequency by using the or button. RDS functions: • Automatic switching function This function compares the strengths of the signals of all the stations on the AF list and selects the station with the optimum reception conditions. Programme Service (PS) function (station name display function) When an RDS station is tuned in with seek or manual tuning, the RDS data is received and the Program Service (PS) name is displayed. For activation or deactivation details, see “MENU button” later in this section. • Enhanced Other Network (EON) data update (This function also operates when the AF mode is off) When EON data is being received, this enables automatic retuning of other preset stations on the same network. Also, network linked services can be used. The EON indicator turns on during the reception of RDS EON stations in the FM mode. Radio data system (RDS) buttons: Program Information (PI) search Program Information (PI) search begins automatically if no suitable station is found with the above automatic switching function. The PI search function checks each RDS station with the same PI code. During this time the sound is muted and “PI SEARCH” is displayed. The PI search operation stops when a suitable station is found. If no station is found once all the frequencies have been searched, the radio returns to the previous frequency. 3 The channel indicator will display and the radio mute disengages, indicating that the memory is stored properly. memory Radio • • Emergency broadcast interrupt function (ALARM INTERRUPTION EBU SPEC FOR INFO) Heater and air conditioner and audio system 4-11 Chapter4.fm Page 12 Thursday, April 11, 2013 2:47 PM When the radio receives PTY code 31 (an emergency broadcast code), the sound is interrupted, the emergency broadcast is heard and “PTY31 ALARM” is displayed. The volume level at this time is the same as that for traffic announcements. Once the emergency broadcast is finished, the unit immediately returns to the previous source. • REG (Regional) mode Some local radio stations are linked together according to their region because they only offer limited coverage due to their limited number of transmitters. If the signal from one station becomes weak while you are driving around, RDS mode will switch to another local station in the region with a stronger signal. When the REG mode is activated in the FM band and the radio receiver is turned to a local radio station, it will keep receiving this radio station without switching to another local station. For activation or deactivation details, see “MENU button” later in this section Traffic Announcement (TA): • The TA function operates in the FM and CD modes. • The TA mode is turned on or off when the TA button is pushed or the TA/NEWS button is pushed for less than 2 seconds. • The TA mode operates regardless of whether the AF mode is on or off. • “TA ON” is displayed when the TA mode is turned on and the TA indicator turns on. “TA OFF” is displayed when the TA mode is turned off and the TA indicator turns off. The following functions operate when the TA mode is on: • Traffic function announcement interrupt When a traffic announcement is received, the announcement is tuned in and the volume increases to the set level. Once the traffic announcement is finished, the unit returns to the source which was set before the traffic announcement started and the volume returns to the previous level. For EON stations, the radio is interrupted by another EON station with traffic announcements. The traffic announcement interrupt mode is cancelled if the TA or TA/NEWS button is pushed during a traffic announcement. The TA mode returns to the standby mode and the audio unit returns to the previous source. News mode When the NEWS button is pushed or the TA/ NEWS button is pushed for longer than 2 seconds in the FM mode, the news function is activated. “NEWS” is displayed for 3 seconds and the NEWS indicator appears on the display. 4-12 Heater and air conditioner and audio system When the news function is activated, the radio receives a news code from the FM broadcasting news station and the actual playing mode will be interrupted. Once the news broadcast is finished, the unit returns to the previous mode. In some countries or regions, this service is not available or this signal is too weak to be received. 1 News standby mode • The news standby mode can be activated in the FM or CD mode. • A news interruption will be announced and “NEWS” will be displayed when the radio detects the news code from the tuned station or EON stations. The display will then change to the PS name of the interrupting station. • When pushing the NEWS button or pushing the TA/NEWS button for longer than 2 seconds, the news standby mode is turned off an the indicator disappears from the display. 2 News interruption mode • When the NEWS button or the TA/NEWS button is pushed during the news interruption mode, the radio returns to the previous source. However, the news standby mode is kept. • When the button is pushed during the news interruption mode, the radio changes to the CD mode. However, the news standby mode is kept. Chapter4.fm Page 13 Thursday, April 11, 2013 2:47 PM ENGLISH DUTCH FRENCH SPANISH GERMAN ITALIAN PORTUGUESE ENGLISH If the radio band is changed to the MW or LW, the news standby mode will be turned off. After selecting the desired language, push the ENTER button to exit the menu. MENU buttons: To configure Alternative Frequency, Regional and Language settings, perform the following procedure: 1 Push and hold the MENU button for at least 1.5 seconds. 2 Turn the MENU/VOL dial clockwise or counter clockwise. The display message will change as follows: AF • REG LANGUAGE AF To activate or deactivate the AF and REG mode, briefly push on the ENTER button when AF or REG appears on the display and turn the MENU/VOL dial clockwise or counterclockwise to switch between the off or on position. After selection, push the ENTER button to confirm the settings. - When the AF mode is enabled, the audio unit will automatically re-tune to a stronger frequency if the radio signal becomes weak. - When the REG mode is enabled, the audio unit will maintain and hold the station which is broadcasting local (regional) programmes. • To change the display language, briefly push the ENTER button when LANGUAGE appears on the display the turn the MENU/ VOL dial clockwise or counterclockwise to select the appropriate language setting. After the desired levels have been set, push the MENU button to exit the menu or wait at least for 10 seconds without pressing any buttons. Ton configure the SPEED volume and BEEP settings, perform the following procedure: 1 Push the MENU button. 2 Turn the MENU/VOL dial clockwise or counterclockwise. The display message will change as follows: SPEED VOL • BEEP When SPEED VOL appears on the display, briefly push on the ENTER button then turn the MENU/VOL dial clockwise or counterclockwise to adjust the level of the volume. Adjusting the setting to 0 (zero) turns off the speed volume feature. Increasing the speed volume setting results in the audio volume increasing more rapidly with vehicle speed. Push the ENTER button again to save the setting. • When BEEP appears on the display, briefly push the ENTER button and then turn the MENU/VOL dial clockwise or counterclockwise to switch the beep sound on or off. Push the ENTER button again to save the setting. Heater and air conditioner and audio system 4-13 Chapter4.fm Page 14 Thursday, April 11, 2013 2:47 PM FM-AM RADIO WITH COMPACT DISC (CD) PLAYER Audio main operation The audio system operates when the ignition switch is in the “ACC” or “ON” position. POWER ON/OFF button: To turn on the audio system push the POWER ON/OFF button. • The system will turn on in the mode, (radio or CD) which was used immediately before the system was turned off. • If there is no CD loaded, the radio will be turned on. To turn off the audio system, push the POWER ON/OFF button. Volume control: To control the volume, turn the VOLUME control dial. 1 MUTE button 9 SCAN button 2 FM-AM radio band select button 10 RDM (Random) button 3 CD button 11 RPT (Repeat) button 4 Radio memory buttons 12 Power button/Volume control knob 5 AUX button 13 AUX In jack 6 CD EJECT button 14 AUTO.P (Automatic Preset) button 7 DISP (Display) button 15 SCRL (Scroll) button 8 SEEK/TRACK/FILE button/APS REW button/APS FF button 16 TUNE/FF-REW/FOLDER button 17 MENU button 4-14 Heater and air conditioner and audio system Turn the VOLUME control dial to make the sound louder. Turn the VOLUME control dial counterclockwise to mae the sound quieter. MENU button: To change the audio settings (BASS, TREBLE, FADE, BALANCE, BEEP AND CLOCK), push the button or select the mode while the CD or radio is on. Push the button until the desired mode appears on the display Chapter4.fm Page 15 Thursday, April 11, 2013 2:47 PM BASS TREBLE FADE BEEP CLOCK automatically change from stereo to monaural reception. BALANCE Push the SEEK/TRACK/FILE button ( or ) or TUNE/FF-REW/FOLDER button ( or ) to adjust the audio settings. . button: When adjusting the broadcasting station frequency manually, push the or button (located on the right side). until the desired frequency is achieved. BASS: (-) to decrease / (+) to increase. TREBL: (-) to decrease / (+) to increase. FADE: (F) to front fade / (R) to rear fade. BALANCE: (R) to right balance / (L) to left balance. Once the audio settings are set to the desired level, push the button until the radio or CD display appears. If not action is performed for approximately 5 seconds, the audio settings mode will automatically return to the normal mode. To turn the beep sound off or on, push the SEEK/TRACK button or or TUNE/FFREW/FOLDER button or until the desired mode is displayed. This turns on or off the beep sound when audio buttons are pushed. Mute button: Press the MUTE button to mute the sound. Press again to restore the sound. TUNE/FF-REW/FOLDER The frequency changes in steps of 100 kHz on the FM band, 9 kHz on the MW band and 3 kHz on the LW band. TUNE/FF-REW/FOLDER FM/AM radio operation button: The audio system operates when the ignition switch is in the “ACC” or “ON” position. When adjusting the broadcasting station frequency automatically, push the or button. When the system detects a broadcasting station, it will stop at the station. FM-AM button: When the button is pushed while the audio system is off, the audio system will turn on and the radio will turn on. When the button is pushed while another audio source is playing, the other audio source will turn off and the radio will turn on. To change the radio bands, push the button. AM FM 1 FM 2 The FM stereo indicator, “ST” will display during FM stereo reception. When the stereo broadcast signal is weak, the radio will SCAN button: When the button is pushed, the system will seek and stop at the detected broadcasting station for 5 seconds, and then it will start to seek for the next broadcasting station Push the button in this 5-second period to stop seeking. Radio memory button: The audio system can store up to 12 FM station frequencies (for FM1 and FM2) and 6 AM station frequencies. Heater and air conditioner and audio system 4-15 Chapter4.fm Page 16 Thursday, April 11, 2013 2:47 PM playing automatically. If the radio is already playing, it will automatically turn off and the CD will start playing. To store the station frequency: 1 Tune to the desired broadcasting station frequency by using the or button (located on the right side). 2 Push and hold a memory button (1-6) until a beep sounds. 3 The switch number and frequency will appear on the display when the memory is stored properly. 4 Perform steps 1-3 for all other memory buttons. Push a memory button (1-6) to select a desired memory. If the battery cable is disconnected, or if the audio fuse blows, the radio memory will be erased. In such a case, reset the desired stations. (Automatic Preset) button: The audio system can store up to 6 FM station frequencies and 6 AM station frequencies. To store the station frequency automatically, push and hold the button until a beep sounds. The station will be automatically stored in the “AUTO.P” memory. The display indicates “AP-**”. Push the memory. button to select a desired Display button: When the button is pushed while a CD with a title is being played, the display will change as follows: CD: CD player operation CD with MP3 or WMA: The audio system operates when the ignition switch is in the “ACC” or “ON” position. Loading: Insert a CD into the slot with the label side facing up. The CD will be guided automatically into the slot and will start playing. To stop playing, push the Power button. After loading the CD, the number of tracks and the playtime will appear on the display. CAUTION: Do not force the CD into the slot. This could damage the player. CD button: When the button is pushed while the audio system is off and a CD is loaded, the audio system will turn on and a CD will start 4-16 Heater and air conditioner and audio system SEEK/TRACK/FILE button: When the button (located on the left side) is pushed wile a CD is being played, the present track will be advanced and move to the next track. Push the button several times to skip forward tracks. The CD will advance the number of times the button is pushed. When the last track of the CD is forwarded, the first track will be played. When the button is pushed while a CD is being played, the present track will start over from the beginning of the current track. Push the button several times to skip back tracks. The CD will rewind the number of times Chapter4.fm Page 17 Thursday, April 11, 2013 2:47 PM the button is pushed. When the first track of the CD is rewound, the last track will be played. TUNE/FF-REW/FOLDER button: When the or button is pushed and held while a CD is being played, the CD will be played while forwarding or rewinding. When the button is released, the CD will return to the normal play speed. When the or button (located on the right side) is pushed while a CD with MP3 or WMA is being played, the first track in the next or the previous folder will be played. SCAN button: When the button is pushed while a CD is being played, the first 10 seconds of all the tracks will be played. When the button is pushed again, the CD will return to normal play from the track which is playing REPEAT button: RPT DISC: RDM DISC: All the tracks of the CD will be played continuously in sequential order. The display indicates no symbol mark. While the button is pushed, the display indicates “RPT DISC”. All the tracks or folders (CD with MP3 or WMA only) of the CD will be played continuously in random order. While the button is pushed, the display indicates “RDM DISC”. RPT TRACK: RDM FOLDER: The selected track of the CD will be played continuously. While the button is pushed, the display indicates “RPT TRACK”. All the tracks of the selected folder will be played continuously in random order (CD with MP3 or WMA only). While the button is pushed, the display indicates “RDM FOLDER”. RPT FOLDER: All the tracks of the selected folder will be played continuously in sequential order (CD with MP3 or WMA only). While the button is pushed, the display indicates “RPT FOLDER”. RANDOM button: To change the play sequence, push the button to select the mode. To eject a CD, push the CD EJECT button. When the button is pushed twice, the CD will be ejected further and the CD can be removed with ease. RPT DISC CD with MP3 or WM: To change the play settings, push the button to select the mode. RDM DISC CD: All the tracks of the CD will be played continuously in sequential order. The display indicates no symbol mark. While the button is pushed, the display indicates “RPT DISC”. RPT DISC RPT TRACK CD with MP3 or WMA: RPT DISC RPT FOLDER RPT TRACK When the title is displayed but it is a long one, the whole title is not shown in the display. In this case, push the button to scroll the title. When the title is scrolled to the end of it, the display will stop moving and return to the first condition. CD EJECT button: CD: RDM DISC SCROLL button: RDM FOLDER RPT RPT DISC: If a CD is ejected by pushing the button and it is not taken out from the loading slot, the CD will automatically be reloaded to the slot to protect the CD (12 cm discs only). Heater and air conditioner and audio system 4-17 Chapter4.fm Page 18 Thursday, April 11, 2013 2:47 PM AUX button: The AUX In jack is located on the audio unit. The AUX IN audio input jack accepts any standard analog audio input such as from a portable casette tape, CD player, MP3 player or laptop computer. Push the AUX button to play a compatible device when it is plugged into the AUX IN jack. NISSAN strongly recommend using a stereo mini plug cable when connecting your music device to the audio system. Music may not be played properly when monaural cable is used. Push the “MENU” button until the display CAR PHONE AND CB RADIO indicates the clock adjustment mode. be adjusted in the following steps: When installing a car phone, a CB or ham radio in your NISSAN, be sure to observe the following cautions, otherwise the new equipment may adversely affect the Multiport fuel injection system and other electronic parts 4 Push the “MENU” button. 5 The time indicator will flash. CAUTION: 2 3 to turn this mode on. Then the clock can Push the “SEEK” button to adjust the hour. Then adjust the minute by pushing the “TUNE” button. Pushing time and CLOCK setting: The digital clock (in the audio unit) displays the time when the ignition switch is in the “ON” position. 6 If the battery cable is disconnected, the clock will reset its time and the display mode. 1 ADJUSTING TIME: 2 Push the “MENU” button to finish the Keep the antenna as far as possible away from the Electric Control Unit (including radio). • Keep the antenna wire more than 20 cm (8 in) away from the Multiport Fuel Injection harness. Do not route the antenna wire next to any harness. • Adjust the antenna standing-wave ratio as recommended by the manufacturer. • Connect the ground wire from the radio chassis to the body. • For details, consult your NISSAN dealer. When clock is displayed: Turn the audio unit on by pushing the ONOFF/VOLUME control knob. Push the “MENU” button until the display indicates the clock adjustment mode. 3 Perform steps 4 to 6 above to adjust the time. When clock is not displayed: If the clock is not displayed with the ignition switch in the “ACC” or “ON” position, you need to select the clock ON mode as follows: 1 • or button will advance the button will turn back the time. clock adjustment. Audio display model You can select clock display ON and OFF mode. Push the “SEEK” button or “TUNE” button Turn the audio unit on by pushing the ONOFF/VOLUME control knob. 4-18 Heater and air conditioner and audio system Chapter5TOC.fm Page 0 Tuesday, September 23, 2014 11:42 AM 5 Starting and driving Running-in schedule............................................................... 5-1 Before starting the engine ..................................................... 5-1 Precautions when starting and driving ............................... 5-2 Exhaust gas (Carbon Monoxide) .................................. 5-2 Three way catalyst (if so equipped .............................. 5-2 Fitment of Canopy ................................................................... 5-3 Turbocharger system (if so equipped) ............................... 5-3 4WD on-road and off-road driving precautions............... 5-3 Care when driving ................................................................... 5-4 Engine cold start period ................................................. 5-4 Loading the luggage........................................................ 5-4 Driving in wet conditions ................................................ 5-4 Driving in icy conditions.................................................. 5-4 Driving at the upland (Diesel engine model).............. 5-4 Trailer towing ............................................................................ 5-4 Ignition switch .......................................................................... 5-7 Key position ....................................................................... 5-8 Starting engine......................................................................... 5-8 Gasoline engine .............................................................. 5-8 Diesel engine without throttle control knob ............... 5-9 Driving vehicle .......................................................................... 5-9 Driving with Manual transmission ................................. 5-9 Suggested shift-up speeds ........................................... 5-9 Suggested maximum speed in each gear ................5-10 Allowed maximum speed in each gear ......................5-10 Four-Wheel Drive ...........................................................5-11 Transfer case shifting procedures ..............................5-11 Diff lock (if so equipped)......................................................5-12 Auto lock free running hubs(if so equipped) ...................5-12 Manual lock free running hubs............................................5-15 Driving safety precautions (4X4)........................................5-17 4X4 tyres of 4-wheel drive ..................................................5-18 Power steering system .........................................................5-18 Brake system ..........................................................................5-18 Brake precautions ..........................................................5-18 Anti-lock Brake System (ABS) (if so equipped) .....5-19 Parking .....................................................................................5-20 Headed downhill.............................................................5-21 Headed uphill ..................................................................5-21 Headed uphill or downhill, no curb.............................5-21 Vehicle security ......................................................................5-22 Cold weather driving.............................................................5-22 Anti-freeze ........................................................................5-22 Battery...............................................................................5-22 Engine coolant ................................................................5-22 Corrosion protection......................................................5-22 Chapter5TOC.fm Page 1 Tuesday, September 23, 2014 11:42 AM Chapter5.fm Page 1 Tuesday, September 23, 2014 11:44 AM RUNNING-IN SCHEDULE During the first 1 600 km (1,000 miles), follow these recommendations for the future reliability and economy of your new vehicle. Failure to follow these recommendations may result in vehicle damage or shortened engine life. • Avoid driving for long periods at constant speed, either fast or slow. • Do not accelerate at full throttle in any gear. • Avoid quick starts and full acceleration. • Avoid hard braking as much as possible. • Do not tow a trailer for the first 800 km (500 miles). BEFORE STARTING THE ENGINE • Do not place hard or heavy objects on either the front or rear parcel shelf to prevent injury in the event of a sudden stop. • Check the operation of warning lights when key is turned to the "ON'' (3) position. • Tune the radio to the desired broadcasting station before driving. WARNING The driving characteristics of your vehicle can be changed remarkably by any additional load and its distribution, as well as by adding optional equipment (trailer couplings, roof racks, etc.). Your driving style and speed have to be adjusted accordingly. ESPECIALLY WHEN CARRYING HEAVY LOADS, YOUR SPEED MUST BE REDUCED ADEQUATELY. • Make sure the area around the vehicle is clear. • Check fluid levels such as engine oil, coolant, brake and clutch fluid, window washer fluid as frequently as possible, at least whenever you refuel. • Check, to be sure that all windows and light lenses are clean. • Visually inspect tyres for their appearance and condition. Also check tyre pressure for proper inflation. • Lock all doors. • Position seats and adjust head restraints. • Adjust inside and outside mirrors. • Fasten seat belts and ask all passengers to do likewise. Starting and driving 5-1 Chapter5.fm Page 2 Tuesday, September 23, 2014 11:44 AM PRECAUTIONS WHEN STARTING AND DRIVING • WARNING Do not leave children, impaired adults, or pets alone in your vehicle. They could accidentally injure themselves or others through inadvertent operation of the vehicle. Also, on hot, sunny days, temperatures in a closed vehicle could quickly become high enough to cause severe or possibly fatal injuries to people or animals. EXHAUST GAS (Carbon Monoxide) WARNING • • Do not breathe exhaust gases; they contain colourless and odourless carbon monoxide. Carbon monoxide is dangerous. It can cause unconsciousness or death. If you suspect that exhaust fumes are entering the vehicle, drive with all windows fully open, and have the vehicle inspected immediately. • Do not run the engine in closed spaces such as a garage. • Do not park the vehicle with the engine running for any extended length of time. • It is not advisable to sit for any length of time in a parked vehicle with the engine running. 5-2 Starting and driving When a vehicle has been stopped in an open area with its engine running for any significant length of time, turn the ventilator on to force outside air into the vehicle. To help prevent damage CAUTION: • Use UNLEADED GASOLINE ONLY. See “RECOMMENDED FUEL/LUBRICANTS AND CAPACITIES” in the “9. Technical information” section for fuel recommendation. Leaded gasoline will seriously damage three-way catalyst. • Do not use leaded gasoline. THREE-WAY CATALYST (if so equipped) The three-way catalyst is an emission control device, installed in the exhaust system. Exhaust gases in the three-way catalyst are burned at high temperatures to help reduce pollutants. Deposits from leaded gasoline will seriously reduce the three-way catalyst’s ability to help reduce exhaust pollutants. CAUTION: • The exhaust gas and the exhaust system are very hot. While the engine is running, keep people or flammable materials away from the exhaust pipe. • Do not stop or park the vehicle over flammable materials such as dry grass, waste paper or rags, as they may burn easily. • When parking, ensure people or inflammable materials are kept away from the exhaust pipe. • Keep your engine tuned up. Malfunctions in the ignition, carburetion/fuel injection, or electrical systems can cause overrich fuel flow into the three-way catalyst, causing it to overheat. Do not keep driving if the engine misfires, or if noticeable loss of performance or other unusual operating conditions are detected. Have the vehicle inspected promptly by a NISSAN dealer. • Avoid driving with an extremely low fuel level. Running out of fuel could cause the engine to misfire, damaging the three-way catalyst. • Do not race the engine while warming it up. • Do not push or tow your vehicle to start the engine. Chapter5.fm Page 3 Tuesday, September 23, 2014 11:44 AM FITMENT OF CANOPY TURBOCHARGER SYSTEM (if so equipped) ON-ROAD AND OFF-ROAD DRIVING PRECAUTIONS CAUTION: The turbocharger system uses engine oil for lubrication and cooling of its rotating components. The turbocharger turbine turns at extremely high speeds and its temperature can reach extremely high degrees. It is essential to maintain a clean supply of oil flowing through the turbocharger system. Therefore, a sudden interruption of oil supply may cause a malfunction in the turbocharger. Vehicles have higher ground clearance and a wider track to make them capable of performing in a wide variety of off-road applications. Specific design characteristics give them a higher centre of gravity than ordinary cars. An advantage of higher ground clearance is a better view of the road, allowing you to anticipate problems. They are not designed for cornering at the same speeds as conventional 2-wheel drive vehicles any more than low-slung sports cars are designed to perform satisfactorily under off-road conditions. If at all possible, avoid sharp turns or abrupt manoeuvres. As with other vehicles of this type, failure to operate this vehicle correctly may result in loss of control or vehicle roll-over. Certain canopy designs may allow the ingress of exhaust gases to the interior, consequently NISSAN recommends the following: Regardless of the type of canopy to be fitted to your Nissan vehicle, please insist on the fitment of a SIDE EXIT extension to the Exhaust Tail Pipe. Side exit extensions are readily available from your local Exhaust fitment centre. For longevity and compatibility with your Nissan Exhaust system, we recommend Stainless Steel tubing for this application. To ensure prolonged life and performance of the turbocharger, it is essential to comply with the following maintenance procedure: CAUTION: • Change your engine oil according to the recommended intervals shown in a separate maintenance booklet. Use only the recommended engine oil. • If the engine had been operating at high rpm for an extended period of time, let it idle for a few minutes prior to shutdown. • Do not accelerate your engine to high rpm immediately after start. Starting and driving 5-3 Chapter5.fm Page 4 Tuesday, September 23, 2014 11:44 AM CARE WHEN DRIVING UNDER ICY CONDITIONS TRAILER TOWING Driving your vehicle to fit the circumstances is essential for your safety and comfort. As a DRIVER, you should be the one who knows best how to drive in the given circumstances. • Drive sensitively. • Avoid sudden steering actions. Your new vehicle was designed to be used primarily for carrying passengers and luggage. • Extra distance should be kept from the vehicle in front. ENGINE COLD START PERIOD Due to the higher engine speeds when the engine is cold, extra caution must be exercised when selecting gear positions during the engine warm-up period after starting the engine. LOADING THE LUGGAGE Loads and their distribution and the attachment of equipment (coupling devices, roof baggage carriers, etc.) will change the driving characteristics of the vehicle considerably. Driving style and speed must be changed according to the circumstances. DRIVING IN WET CONDITIONS and YD25DDTI engine except for high altitude specification model: Avoid driving at an altitude higher than 3,000 m (9,843 ft). It may cause loss of emission control effect and driveability, or it may be hard to start the engine. Your driving style and speed must be changed according to the circumstances. Before towing a trailer, see a NISSAN dealer for an explanation about the proper use of towing equipment OPERATING PRECAUTIONS • Avoid towing a trailer during the running-in period. • Before driving, make sure that the lighting system of the trailer works properly. • Observe the legal maximum speeds for trailer operation. • Avoid starting off, stopping suddenly. • Avoid sharp turns or lane changes. • Avoid sharp turns or lane changes. • • Extra distance should be kept from the vehicle in front. Always drive your vehicle at a moderate speed. • Take note instructions. • Choose proper coupling devices (trailer hitch, safety chain, etc.) for your vehicle and trailer. These devices are of course available at your NISSAN Dealer where you • accelerating DRIVING AT THE UPLAND (Diesel engine models) Towing a trailer will place additional loads on your vehicle's engine, drivetrain, steering, braking and other systems. The towing of a trailer will exaggerate other conditions such as sway caused by crosswinds, rough road surfaces or passing trucks. When water covers the road surface in puddles, small streams, etc., REDUCE SPEED to prevent aquaplaning which will cause skidding and loss of control. Worn tyres increase this risk. 5-4 Starting and driving of trailer manufacturer's Chapter5.fm Page 5 Tuesday, September 23, 2014 11:44 AM can obtain more detailed information on trailer towing. TOWING – LEGAL AND SAFETY ASPECTS • Never allow the total trailer load (trailer weight plus its cargo weight) to exceed the maximum set for the coupling device. • The trailer must be loaded so that heavy goods are placed over the axle. The maximum allowable vertical load on the trailer hitch must not be exceeded. The following information may be seen as the basic set of rules with which to comply, firstly to satisfy safety and legal requirements, and secondly to ensure comfortable driving. Confirm Towing Regulations with your local authorities. • Have your vehicle serviced more often than at the intervals specified in a separate maintenance booklet. • Trailer towing requires more fuel than under normal circumstances because of a considerable increase in traction power and resistance. • Use the 4L (4WD models) when starting out or driving up a steep slope. • Always block the wheels on both vehicle and trailer when parking. Apply parking brake on trailer where fitted. • Take care that the tyre pressures are at the pressure for full loading shown on the tyre placard. • Avoid abrupt starts, acceleration or stops. • Parking on a recommended. steep slope is not BRAKES AND TOWED MASS If the towed gross vehicle mass is 750 kg (1,643 lb) or less and does not exceed half of the tare of the towing vehicle, the towed vehicle MUST be equipped with either a parking device or a parking brake. If the towed gross vehicle mass is 750 kg (1,643 lb) or less and exceeds half of the tare of the towing vehicle, the towed vehicle MUST be equipped with a parking brake, as well as either an overrun brake or service brake. If the towed gross vehicle mass is between 750 kg (1,643 lb) and 3 000 kg (6,614 lb) and does not exceed the tare of the towing vehicle, the towed vehicle MUST be equipped with a parking brake, as well as either an overrun brake or a service brake. If the towed gross vehicle mass exceeds the towing vehicle tare, or 3 500 kg (7,716 lb), it MUST be equipped with a parking brake AS WELL AS a service brake. CAUTION: The tare mass is supplied on the licence disk as well as the Registration Certificate of your vehicle. NISSAN recommends that the mass of the trailer or caravan (Towed gross vehicle mass) must NOT exceed the difference between the GCM (Gross Combined Mass) and GVM (Gross Vehicle Mass). See Section “9. Technical Information” for the Vehicle Identification plate position on which the GVM and GCM are displayed. Thus the towed gross vehicle mass must not exceed the following: Engine type: 2.0 Gasoline 2.4 Gasoline 2.5 Turbo Diesel 1 250 kg (2,756 lb) 1 400 kg (3,087 lb) 1 400 kg (3,087 lb) It is dangerous to overload a towbar and failure to adhere to this load limit will void the warranty on the towbar. All the models/variants are fitted with a rear bumper/towbar combination, but not with the tow-ball, drop-plate, fasteners, socket and wiring harness. These mentioned parts are available as an appropriate P&A item/kit available from NISSAN Parts and Accessories Division. This kit has been designed specifically to suit the original equipment towbar and also contains a data plate indicating the maximum loads for the towbar. It is strongly recommended that this P&A kit be used, instead of any other “aftermarket” tow-ball kits. NISSAN is not responsible for Starting and driving 5-5 Chapter5.fm Page 6 Tuesday, September 23, 2014 11:44 AM any damage to the vehicle or loss of property that may result from fitting any kit other than the approved P&A kit. NOSE MASS The nose mass, that is the total mass on the ball coupling, shall not be less than 25 kg (55 lb) and not more than 90 kg (199 lb). CAUTION: Have your NISSAN Hardbody headlight beam settings checked by an authorised NISSAN dealer with the loaded caravan or trailer coupled to your vehicle, as the settings may need adjustment to compensate for the added weights pressing down on the towing hitch of the vehicle. The correct nose mass is achieved by proper storage and/or loading of the caravan or trailer. MIRRORS TOWING HEIGHT Extended rear-view mirrors must be fitted to both sides (left and right) of the towing vehicle. The minimum towing height is 350 mm (14 in), and the maximum 420 mm (17 in) from the road surface to the centre of the towing ball. The towing vehicle must not sag, and the towed vehicle should be horizontal or slightly nose-down. LIGHTS Ensure that the tail lights, brake lights, reverse light (if fitted) and indicator lights on the towed vehicle work. SPEED LIMITS The maximum speed limits in force when towing a caravan or trailer, are those posted on the highways, main roads, roads or in urban areas. CAUTION: NISSAN recommends that a maximum towing speed of 90 km/h (56 mph) should not be exceeded under the most favourable conditions. Reduce speed at the first sign of adverse conditions ahead. LOADING THE CARAVAN OR TRAILER The payload or contents of the caravan or trailer should be stored as low and as close to the middle as possible, to ensure a low centre of gravity. This will result in greater stability when travelling. Light items should be loaded in the front and rear. All items must be secured properly to prevent sideways or fore/aft movement. WARNING Do not exceed the individual Gross Vehicle Mass or the Gross Combined Mass of your NISSAN Hardbody and caravan / trailer. TYRE PRESSURES Inflate the tyres of the caravan or trailer when cold to the pressures recommended by the manufacturer. Inflate the rear tyres of your NISSAN Hardbody to the maximum load pressures indicated in the TECHNICAL SPECIFICATIONS. WARNING Uneven tyre pressures can cause the caravan or trailer to sway. 5-6 Starting and driving Chapter5.fm Page 7 Tuesday, September 23, 2014 11:44 AM DRIVING RECOMMENDATIONS WHEN TOWING SWAY PREVENTION AND CONTROL Pull-away should be gentle and smooth. Smooth, steady braking will yield the shortest stopping distances. Swaying should not occur when your NISSAN Hardbody and caravan or trailer is properly matched. WARNING Hard braking can cause jack-knifing or set up a whiplash effect. DO NOT push engine speed into the red zone of the tachometer. When going uphill, change down early, to ascend without strain. When going downhill, DO NOT accelerate, but let the engine run against compression. IGNITION SWITCH Should the combination tend to sway, however, an anti-sway device can be fitted. Sway can also be caused by excessive downhill speed, uneven braking, uneven tyre pressures, or a badly loaded or nose heavy caravan or trailer. Should the combination start to sway: • STAY CALM. • Hold the steering wheel firmly. • Steer a STRAIGHT line. Overtaking should ONLY be undertaken on level, straight stretches of road, or on gentle, long uphill gradients. • DO NOT brake hard. • DO NOT steer movement. NO passengers are allowed in the caravan or trailer whilst travelling. • DO NOT attempt acceleration to pull the combination straight. WARNING DO NOT overtake on a downhill – this is extremely dangerous. into the Type A sway Type B Starting and driving 5-7 Chapter5.fm Page 8 Tuesday, September 23, 2014 11:44 AM The switch includes an anti-theft steering lock device. The ignition key can only be removed when the switch is in the “LOCK” normal parking position (0). Type A: To turn the ignition switch to the “LOCK” position from the “ACC” or “ON” position, turn the key to the “OFF” position, then turn the key to the “LOCK” position. Type B: To turn the ignition switch to the “LOCK” position from the “ACC” or “ON” position, turn the key to the “OFF” position, push the key in, then turn the key to the “LOCK” position. There is an “OFF” position in between LOCK and ACC, although it does not show on the lock cylinder. When the ignition is in “OFF” the steering wheel is not locked. In order for the steering wheel to be locked, it must be turned about 1/6 of a turn clockwise from the straight up position. To lock the steering wheel, remove the key. To unlock the steering wheel, insert the key and turn it gently while rotating the steering wheel slightly right and left. WARNING Never remove the key while driving. If the key is removed, the steering wheel will lock. This may cause the driver to lose control of the vehicle and could result in serious vehicle damage or personal injury. 5-8 Starting and driving KEY POSITIONS engine starts. If the engine starts, but fails to run, repeat the above procedure. - If the engine is very hard to start in extremely cold or hot weather or when restarting, depress the accelerator pedal a little (approximately 1/3 to the floor) and hold it and then crank the engine. Release the key and the accelerator pedal when the engine starts. LOCK (Normal parking position) (0): The ignition key can only be removed at this position. OFF (1) The engine can be turned off without locking the steering wheel. - If the engine is very hard to start because it is flooded, depress the accelerator pedal all the way to the floor and hold it. Crank the engine for 5-6 seconds. After cranking the engine, release the accelerator pedal. Crank the engine with your foot off the accelerator pedal by turning the ignition key to START. Release the key when the engine starts. If the engine starts, but fails to run, repeat the above procedure. ACC (Accessories) (2) This position activates electrical accessories such as the radio when the engine is not running. ON (Normal operating position) (3) This position turns on the glow plug system and electrical accessories. START (4) Do not operate the starter for more that 15 seconds at a time. If the engine does not start, turn the key off and wait 10 seconds before cranking again, otherwise the starter could be damaged. This position starts the engine. As soon as the engine has started, release the key immediately. It will automatically return to the "ON" position. STARTING THE ENGINE GASOLINE ENGINE 1 2 3 Apply the parking brake. Move the shift lever to “N” (Neutral). Depress the clutch pedal to the floor while cranking the engine. Crank the engine with your foot off the accelerator pedal by turning the ignition key to “START”. Release the key when the 4 Allow the engine to idle for at least 30 seconds after starting. Do not race the engine while warming it up. Drive at a moderate speed for a short distance first, especially in cold weather. Chapter5.fm Page 9 Tuesday, September 23, 2014 11:44 AM DIESEL ENGINE WITHOUT THROTTLE CONTROL KNOB 1 Apply the parking brake. 2 Move the gearshift lever to "N" (Neutral), and depress the clutch pedal to the floor while cranking the engine. 3 Turn the ignition key to "ON" and wait until the glow plug indicator light goes out. 4 • • 5 DRIVING WITH MANUAL TRANSMISSION If it is difficult to move the shift lever into Reverse or 1st, shift into Neutral, then release the clutch pedal. Fully depress the clutch pedal again and shift into Reverse or 1st again. On the 5-speed transmission model, you cannot shift directly from 5th gear into Reverse. First shift into Neutral, then into Reverse after stopping the vehicle completely. After the glow plug indicator light goes out, crank the engine with your foot off the accelerator pedal by turning the ignition key to "START". Release the key when the engine starts. Do not crank the engine for more than 20 seconds at a time. If the engine does not start, turn the key off and wait 20 seconds before cranking again, otherwise the starter could be damaged. If the engine is very hard to start in extremely cold weather, use the accelerator pedal to help start the engine Allow the engine to idle for about 30 seconds. may be heard. Transmission damage could occur. CAUTION: Starting the vehicle 1 Depress the clutch pedal to the floor and move the shift lever to the "1'' or "R'' position. 2 Slowly depress the accelerator pedal, releasing the clutch pedal and parking brake lever at the same time. • Do not rest your foot on the clutch pedal while driving. This may cause clutch damage. • Fully depress the clutch pedal before shifting to help prevent transmission damage. • Stop your vehicle completely before shifting into reverse. • When you are shifting from one gear to another, be certain to press the clutch pedal all the way to the floor to avoid clashing or chipping the gears. • Avoid abrupt starts and acceleration for your safety. Shifting the gear To change gears, fully depress the clutch pedal, then move the gearshift lever. After shifting, release the clutch slowly and smoothly. To ensure smooth gear changes, fully depress the clutch pedal before operating the shift lever. If the clutch pedal is not fully depressed before the transmission is shifted, a gear noise When quick acceleration is required for some reason, shift to a lower gear and accelerate until the vehicle reaches the maximum speed in each gear. Do not exceed the speed limit of any gear. Pay special attention when accelerating or Starting and driving 5-9 Chapter5.fm Page 10 Tuesday, September 23, 2014 11:44 AM when shifting into a lower gear on slippery surfaces. Sudden acceleration or down shifting could cause the wheels to skid and result in loss of control. SUGGESTED SHIFT-UP SPEEDS The following provides suggested speed ranges for shifting into a higher gear. These suggestions relate to fuel economy and vehicle performance. Actual shift ranges should be adjusted for specific road conditions, the weather and individual driving habits. 2-WHEEL/4-WHEEL DRIVE MODELS (2H and 4H POSITION) GEAR Km/h (MPH) 1st to 2nd 24 (15) 2nd to 3rd 40 (25) 3rd to 4th 64 (40) 4th to 5th 72 (45) 4-WHEEL DRIVE MODELS (4L POSITION) GEAR Km/h (MPH) 1st to 2nd 13 (8) 2nd to 3rd 20 (12) 5-10 Starting and driving 4-WHEEL DRIVE MODELS (4L POSITION) 3rd to 4th 32 (20) 4th to 5th 36 (22) The figures listed in the chart refer to potential speed ranges for each gear. The speed at which you drive, however, should conform to all federal, government, province and territory laws, and to the condition which will permit safe operation. SUGGESTED MAXIMUM SPEED IN EACH GEAR Downshift to a lower gear if the engine is not running smoothly, or if you need to accelerate. Do not exceed the maximum suggested speed (shown below) in any gear. For level road driving, use the highest gear suggested for that speed. Always observe posted speed limits, and drive according to the road conditions which will ensure safe operation. Do not over-rev the engine when shifting to a lower gear as it may cause engine damage or loss of vehicle control. ALLOWABLE MAXIMUM SPEED IN EACH GEAR 2-WHEEL/4-WHEEL DRIVE MODELS (2H POSITION) GEAR Km/h (MPH) 1st 45 (28) 2nd 70 (44) 3rd 115 (71) 4th 160 (99) 4-WHEEL DRIVE MODELS (4H POSITION) GEAR Km/h (MPH) 1st 35 (22) 2nd 60 (38) 3rd 80 (50) 4th & 5th 80 (50) Chapter5.fm Page 11 Tuesday, September 23, 2014 11:44 AM 4-WHEEL DRIVE MODELS (4L POSITION) GEAR Km/h (MPH) 1st 15 (9) 2nd 30 (19) 3rd 45 (28) 4th & 5th 50 (30) TRANSFER CASE SHIFTING PROCEDURES FOR 4-WHEEL DRIVE VEHICLES • 2 – Shifting between 4H and 4L must always be done whilst stationary. (Standing still) 4L – (4WD, low range) Four wheels are driven. Use when climbing or descending steep hills, or during hard driving in sand, mud or deep snow. The “4L” position provides maximum power and traction. Avoid raising vehicle speed excessively, as the maximum speed in 5th gear is approximately 50 km/h (30 MPH). N- 2H- (2WD, high range) Only the rear wheels are driven. Use when driving under the same conditions as standard 2WD vehicle. 4H- (4WD, high range) Four wheels are driven. Use when driving on roads where it is difficult to drive in the 2H position (i.e. driving at normal speeds on snow covered, icy, wet, muddy or sandy roads). The “4H” position provides maximum power and traction. Avoid excessive speed, as it will cause loss of traction. Speed over 80 km/h (50 MPH) in 4H is not recommended. • 1 – Shifting between 2H and 4H can be done whilst moving [Max speed = 40 km/h (25 MPH)] No wheels are driven. Always leave the transfer lever out of the “N” position, Shift the lever quickly and smoothly when moving across the “N” position with the vehicle stopped. If the lever is stopped during shifting, gears may grind. Note: You must push down (depress) on the shift (transfer) lever and shift quickly and smoothly (one continuous movement) back & forth between 4H, N & 4L. CAUTION: • Do not drive on dry hard surface roads in 4-wheel drive. Driving on dry hard surfaces in “4H” or “4L” may cause unnecessary noise and tyre wear as well as increased fuel consumption. NISSAN Starting and driving 5-11 Chapter5.fm Page 12 Tuesday, September 23, 2014 11:44 AM recommends driving in the “2H” position under these conditions. • To lubricate the front wheel drive system, drive the vehicle in 4-wheel drive at least once a month. WARNING • • • DIFF LOCK (If so equipped) To prevent the rear wheel from spinning in poor traction conditions (e.g. Mud, sand or grass) Only "Engage" or "Disengage" DIFF LOCK at low speed [Max. 30 km/h (19 MPH)] or when stopped. When parking the vehicle, apply the parking brake and shift the transfer control lever in the “2H”, “4H” or “4L” position, CAUTION: • One wheel is jacked up, Do not leave the transfer control lever in the “N” position. Otherwise, the vehicle could roll unexpectedly even if the transmission is in a gear. • On firm surfaces with good traction, • While rear wheel is spinning Failure to engage the transfer control lever in “2H”, “4H” or “4L” could result in the vehicle moving unexpectedly, which could cause serious personal injury or property damage. Do not move the transfer lever from “4H” or “4L” to “4L” or “4H”, from “2H” to “4L” and from “4L” to “2H” with the engine turned off. Otherwise, you may have difficulty in moving the transfer lever to the desired position. Do not leave the transfer lever in the N position with the engine running. Stopping with the transfer case in the N position may cause gear grinding when selecting another gear. Changing the transfer case gear quickly and smoothly will eliminate this. 5-12 Starting and driving Do not engage DIFF LOCK when: Also see DIFF LOCK warning label on inside of windscreen. AUTO-LOCK FREE-RUNNING HUBS (If so equipped) The auto-lock free-running hub is designed to allow for automatic 4-wheel drive engagement when the shift lever is moved to the "4H" or "4L" position. If your vehicle is equipped with this system, follow these operational cautions: CAUTION: • When engaging and disengaging, the auto-lock hubs will make a clicking noise. This is normal. • Accelerating the vehicle suddenly from a stop with the transfer lever in the "4H" or "4L" position may not engage the auto-lock free-running hub and may cause a clattering noise. Continued use of the vehicle with this noise may damage the hub lock. In such case, release the accelerator pedal to reduce the engine speed. Chapter5.fm Page 13 Tuesday, September 23, 2014 11:44 AM • If the auto-lock hubs make a clattering noise while driving in the "2H" position, stop and move the vehicle about 2 to 3 metres (7 to 10 ft) in the opposite direction of travel. • Under extremely cold conditions [below -15 C (5°F)], when the vehicle is driven in 2-wheel drive at high speeds without first warming up the vehicle and gear oil, the axle shafts may rotate, causing the hubs to make a clattering noise. To avoid this, first drive in 4-wheel drive, then shift to 2wheel drive. • When shifting from the "2H" to "4H" position while driving, do not stop shift lever movement midway. An incomplete shift from the "2H" to "4H" position or disengagement of only one hub lock may cause a clattering noise from the auto-lock hubs. Continued use of the vehicle with this noise may damage the hub lock. Shift to 4-wheel drive to stop the noise; unlock hubs as described. Also in cold weather, if difficulty is encountered in shifting from "2H" to "4H", it may be necessary to reduce speed or stop the vehicle. Starting and driving 5-13 Chapter5.fm Page 14 Tuesday, September 23, 2014 11:44 AM TO SHIFT TRANSFER: SHIFT PROCEDURE FOR AUTO-LOCK FREE-RUNNING HUBS From "2H" to "4H" Move the transfer case shift lever to “4H” at speeds below 40 km/h (25 MPH). It is not necessary to depress the clutch pedal or to move the selector lever to the N position. Perform this operation when driving straight. Move the transfer case shift lever to "2H". This can be done at any speed up to 80 km/h (50 MPH) and it is not necessary to depress the clutch pedal or move the selector lever to the N position. Perform this operation when driving straight. NOTE: • From "4H" to "2H" From "4H" or "4L" to "4L" or "4H" From "2H" to "4L" For 2-wheel drive operation, set the free-running hubs in the disengaged position. AUTOLOCK hubs will not disengage until the vehicle is moved about 1 m (3 feet) in the opposite direction of travel: - When driving forward, stop and move 1 m (3 feet) in reverse. - When backing up, stop and move 1 m (3 feet) forward, then move the vehicle about 1 m (3 feet) in reverse. • If the 4-wheel drive indicator light remains on when shifting from 4H, the 2-wheel drive is not selected. Ensure safety and either accelerate, decelerate or back up the vehicle to change to 2-wheel drive. 1 Stop the vehicle. Keep the engine running. 2 Depress the clutch pedal, or move the transmission selector lever in the N (Neutral) position. 3 Depress the transfer case shift lever and move it to the desired "4L" or "4H" position. Change gears quickly and smoothly. 1 Stop the vehicle. Keep the engine running. 2 Depress the clutch pedal, or move the transmission selector lever in the N (Neutral) position. 3 Depress the transfer case shift lever and move it to "4L" position. Change gears quickly and smoothly. 1 Stop the vehicle. Keep the engine running. 2 Depress the clutch pedal, or move the transmission selector lever in the N (Neutral) position. 3 Depress the transfer case shift lever and move it to "2H" position. Change gears quickly and smoothly. From "4L" to "2H" NOTE: • • 5-14 Starting and driving Follow the “NOTE” shown in shifting from 4H to 2H. If the 4-wheel drive indicator light remains on when shifting from 4H to 2H, the 2-wheel drive is not selected. Ensure safety and either accelerate, decelerate or back up the vehicle to change to 2-wheel drive. Chapter5.fm Page 15 Tuesday, September 23, 2014 11:44 AM CAUTION: MANUAL-LOCK FREE-RUNNING HUBS (if so equipped) The manual-lock free-running hubs are designed to allow you to engage or disengage the front drive shaft to the front wheels. Before driving, set the free-running hub to the desired position: • 2-wheel operation - Turn the knob to the FREE position. • 4-wheel operation - Turn the knob to the LOCK position. • Never drive in 4-wheel drive ("4H" or "4L") with the free-running hubs in the FREE position. • Do not drive your vehicle with the left and right free-running hub set to different positions. • For the first 500 km (300 miles) it is recommended that you drive in the "2H" position, with the free-running hubs set in the LOCK position. • To ensure proper lubrication of front drive components, drive in the LOCK position for at least 16 km (10 miles) each month. NOTE: If knob is difficult to turn when dis-engaging (unlock), move the vehicle forward for ½ to ¾ of a wheel turn until knob turns easily (i.e. until 4 wheel drive light is switch off). Be certain to align the " " mark on the knob with the " " mark on the wheel hub. Starting and driving 5-15 Chapter5.fm Page 16 Tuesday, September 23, 2014 11:44 AM TO SHIFT TRANSFER: From "2H" to "4H" From "4H" to "2H" SHIFT PROCEDURE FOR MANUAL-LOCK FREE-RUNNING HUBS 1 2 3 Move the transfer lever to "2H". This can be done at any speed up to 80 km/h (50 MPH) and it is not necessary to depress the clutch pedal or move the selector lever to the N position. Perform this operation when driving straight. NOTE: • For 2-wheel drive operation, set the free-running hubs in the FREE position. This will allow for better fuel economy, quieter ride and less component wear. • If the 4-wheel drive indicator light remains on when shifting from "4H" to "2H", the 2-wheel drive is not selected. Ensure safety and either accelerate, decelerate or reverse the vehicle to change to 2-wheel drive. 1 From "4H" or "4L" to "4L" or "4H" 2 3 1 From "2H" to "4L" 2 3 1 2 3 From "4L" to "2H" Stop the vehicle. Keep the engine running. Depress the clutch pedal, or move the transmission selector lever in the N (Neutral) position. Depress the transfer lever and move it to the desired "4L" or "4H" position. Change gears quickly and smoothly. Stop the vehicle. Keep the engine running. Depress the clutch pedal, or move the transmission selector lever in the N (Neutral) position. Depress the transfer lever and move it to "4L". Change gears quickly and smoothly. Stop the vehicle. Keep the engine running Depress the clutch pedal, or move the transmission selector lever in the N (Neutral) position. Depress the transfer lever and move it to "2H". Change gears quickly and smoothly. NOTE: • Follow the "NOTE" shown in shifting from "4H" to "2H". • 5-16 Starting and driving Stop the vehicle. Set free-running hubs in the LOCK position. Move the transfer lever to "4H". This can be done at any speed up to 80 km/h (50 MPH) and it is not necessary to depress the clutch pedal or move the selector lever to the N position. Perform this operation when driving straight. If the 4-wheel drive indicator light remains on when shifting from "4H" to "2H", then 2-wheel drive is not selected. Ensure safety and either accelerate, decelerate or reverse the vehicle to change to 2-wheel drive. Chapter5.fm Page 17 Tuesday, September 23, 2014 11:44 AM DRIVING SAFETY PRECAUTIONS • Your NISSAN is designed for both normal and off-road use. However, avoid driving in deep water or mud as your NISSAN is mainly designed for leisure use, unlike a conventional off-road vehicle. Remember that two-wheel drive models are less capable than four-wheel drive models for rough road driving and extrication when stuck in deep snow or mud, or the like. • Please observe the following precautions: • • • Heavy braking going down a hill could cause the brakes to overheat and fade, resulting in loss of control and an accident. Apply brakes lightly and use a low gear to control your speed. • Drive carefully when off the road and avoid dangerous areas. Always wear your seat belts to help keep you and your passengers in position when driving over rough terrain. Unsecured cargo can be thrown around when driving over rough terrain. Properly secure it so that it will not be thrown forward and cause injury to you or your passengers. • Do not drive across steep slopes. Instead, drive either straight up or straight down the slopes. Off-road vehicles can tip over sideways much more easily than they can forward or backward. Avoid raising the centre of gravity by loading things on the roof or equipping the vehicle with tyres larger than specified in this manual. This could cause your vehicle to roll over. Put heavy loads in the cargo area as far forward and as low as possible, • Do not grip the inside or spokes of the steering wheel when driving off-road. The steering wheel could jerk and injure your hands. Instead drive with your fingers and thumbs on the outside of the rim. • Before operating the vehicle, ensure that the driver and all passengers have their seat belts fastened. • Always drive with the floor mats in place as the floor may become very hot. Particular care should be taken if you are barefoot. CAUTION: • If your engine stalls or you cannot make it to the top of a steep hill, never attempt to turn around. Your vehicle could tip or roll over. Always back straight down in reverse gear. Never back down in neutral (N) or with the clutch depressed, using only the brake, as this could cause loss of control. Many hills are too steep for any vehicle. If you drive up them, the engine may stall. If you drive down them, you may not be able to control your speed. If you drive across them, the vehicle may roll over. Stay alert when driving to the top of a hill. At the top there could be a dropoff or other hazard that could cause an accident. • Lower your speed when encountering strong crosswinds. With its higher centre of gravity, your Nissan is more affected by gusty side winds. Slower speeds ensure better vehicle control. • Do not drive beyond the performance of the tyres even with 4WD. Sudden acceleration, sharp steering manoeuvres or sudden braking may cause loss of control. • Be sure to check the brakes immediately after driving in mud or water as specified in "WET BRAKES” later in this section. • Whenever you drive off-road through sand, mud or water as deep as the wheel hub, more frequent maintenance may be required. For details, refer to “Maintenance under severe driving conditions” in a separate maintenance booklet. • Avoid parking your vehicle on steep hills. If you get out of the vehicle and it rolls forward, backward or sideways, you could be injured. Starting and driving 5-17 Chapter5.fm Page 18 Tuesday, September 23, 2014 11:44 AM TYRES OF 4-WHEEL DRIVE VEHICLES CAUTION: Always use tyres of the same size, brand, construction (bias, bias-belted or radial) and tread pattern on all four wheels. Failure to do so may result in a circumference difference between tyres on the front and rear axles which will cause excessive tyre wear and may damage the transmission, transfer case and differential gears. If excessive tyre wear is found, it is recommended that all four tyres be replaced with tyres of the same size, brand, construction and tread pattern. The tyre pressure and wheel alignment should also be checked and corrected as necessary. Contact your NISSAN Dealer. Tyre inflation pressure Check the pressure in all tyres, including the spare, with a gauge periodically when at a service station. Adjust to the specified pressure if necessary. Tyre pressures are shown on the tyre placard affixed. For tyre placard location information, refer to “TYRE PLACARD” in the “9. Technical information” section. POWER STEERING SYSTEM BRAKE SYSTEM The power assisted steering is designed to use a hydraulic pump, driven by the engine, to assist steering. PRECAUTIONS WHEN DRIVING Vacuum assisted brakes If the engine stops or dive belt breaks, you will still have control of the vehicle. However, much greater steering effort is needed, especially in sharp turns or at low speeds. The brake booster aids braking by using engine vacuum. If the engine stops or the drive belt is broken, you can stop the vehicle by depressing the brake pedal. However, greater foot pressure on the brake pedal will be required to stop the vehicle and the stopping distance will be longer. WARNING Do not coast with the engine stopped. Wet brakes When the vehicle is washed or driven through water, the brakes may get wet. As a result, your braking distance will be longer and the vehicle may pull to one side during braking. To dry brakes, drive the vehicle at a safe speed while lightly pressing the brake pedal to heat up the brakes. Do this until the brakes return to normal. Avoid driving the vehicle at high speeds until the brakes function correctly. CAUTION: • Avoid resting your foot on the brake pedal while driving. This will overheat the brakes, wear out the brake linings and pads faster and increase fuel consumption. • To help save the brakes and to prevent the brakes from overheating, reduce speed and downshift to a Tyre rotation NISSAN recommends that tyres be rotated periodically. Do not include the temporary spare tyre in the tyre rotation. 5-18 Starting and driving Chapter5.fm Page 19 Tuesday, September 23, 2014 11:44 AM lower gear before going down a slope or long grade. Overheated brakes may reduce braking performance and could result in loss of vehicle control. • While driving on a slippery surface, be careful when braking, accelerating or downshifting. Abrupt braking actions or sudden acceleration could cause the wheels to skid. Driving uphill When starting on a steep grade, it is sometimes difficult to operate both the brake and clutch. Use the parking brake to hold the vehicle. Do not slip the clutch. When ready to start, slowly release the parking brake while depressing the accelerator pedal and releasing the clutch. Driving downhill The engine braking action is effective for controlling the vehicle while descending hills. The gearshift lever should be placed in the lower speed position prior to descending. ANTI-LOCK BRAKE SYSTEM (ABS) (if so equipped) The anti-lock brake system controls the brakes at each wheel so the wheels will not lock when braking abruptly or when braking on slippery surfaces. The system detects the rotation speed at each wheel and varies the brake fluid pressure to prevent each wheel from locking and sliding. By preventing wheel lockup, the system helps the driver maintain steering control and helps to minimize swerving and spinning on slippery surfaces. If a tyre slips on rough roads for more than approximately 40 seconds, the ABS warning light may come on. Turn OFF the ignition key, restart the engine and drive the vehicle at speeds above 30 km/h (20 MPH). If the warning light does not go out, have the vehicle checked at a NISSAN dealer. Self-test function The anti-lock brake system consists of electronic sensors, electric pumps, and hydraulic solenoids controlled by a computer. The computer has a built-in diagnostic feature that tests the system each time you start the engine and move the vehicle at a low speed in forward or reverse. When the "self-test'' occurs, you may hear a "clunk'' noise and/or feel a "pulsation'' in the brake pedal. This is normal and is not an indication of any malfunction. If the computer senses any malfunction, it switches the anti-lock brake system OFF and turns on the "ABS'' warning light in the dashboard. The brake system will then behave normally, but without anti-lock assistance. If the light comes on during the self check, or while you are driving, you should take your vehicle to your NISSAN Dealer for repair at your earliest convenience. Normal operation The anti-lock brake system will not operate at speeds below 5 to 10 km/h (3 to 6 MPH) to completely stop the vehicle. (The speeds will vary according to road conditions.) When the anti-lock system senses that one or more wheels are close to locking up, the actuator (under the hood) rapidly applies and releases hydraulic pressure (like pumping the brakes very quickly). While the actuator is working, you may feel a pulsation in the brake pedal and hear a noise or vibration from the actuator under the hood. This is normal and indicates that the anti-lock system is working properly. However, the pulsation may indicate that road conditions are hazardous and extra care is required while driving. WARNING The anti-lock brake system is a sophisticated device, but cannot prevent accidents resulting from careless or dangerous driving techniques. It can help maintain vehicle control during braking on slippery surfaces, but remember that the stopping distance on slippery surfaces and gravel roads will be longer than on normal surfaces, even with the anti-lock system. Ultimately, the responsibility for safety of self and others rests in the hands of the driver. Tyre type and condition may also affect braking effectiveness. Starting and driving 5-19 Chapter5.fm Page 20 Tuesday, September 23, 2014 11:44 AM • • When replacing tyres, install the specified size of tyres on all the 4 wheels. PARKING When installing a spare tyre, make sure it is the proper size and type as specified on the tyre placard. For tyre placard location information, refer to “TYRE PLACARD” in the “9. Technical information” section. • Do not park the vehicle over flammable materials such as dry grass, waste paper or rags, as they may burn easily. • Never leave the engine running while the vehicle is unattended. • Never leave children unattended in the vehicle. WARNING Safe parking procedures require that the parking brake be set and the gear shift lever placed in the proper position. 1 Firmly apply the parking brake. 2 Place the transmission shift lever in the "REVERSE'' position when parking on a down hill grade. 3 When parking on an uphill grade, place the shift lever in the "1st'' (Low gear) position. 4 Turn the ignition key to the "LOCK'' position and remove the key. WARNING 5-20 Starting and driving • The transfer control lever must be in the "2H", "4H" or "4L" position to prevent the vehicle from moving. . • Never place it in the "N" neutral position. Chapter5.fm Page 21 Tuesday, September 23, 2014 11:44 AM When parked on a sloping driveway, turn the wheels so the vehicle will not roll into the street in case it moves. HEADED DOWNHILL: Turn the wheels into the curb , allow the vehicle to move forward until the curb side wheel gently touches the curb. Then set the parking brake. HEADED UPHILL: Right-hand drive models Turn the wheels away from the curb and allow the vehicle to move back until the curb side wheel gently touches the curb. Then set the parking brake. HEADED UPHILL OR DOWNHILL, NO CURB: Turn the wheels toward the side of the road so the vehicle will move away from the centre of the road if it moves. Then set the parking brake. Left-hand drive models Starting and driving 5-21 Chapter5.fm Page 22 Tuesday, September 23, 2014 11:44 AM VEHICLE SECURITY COLD WEATHER DRIVING When leaving your vehicle unoccupied: Anti-freeze • Always remove the ignition key - even in your own garage. • Close all windows completely and lock all doors. • Always park your vehicle where it can be seen. At night, park in a well lit area. • If you have an alarm or immobilization device, use it - even for short periods. • Do not leave children and pets in the vehicle unattended. • Do not leave valuables on view to tempt a thief. Always take your valuables with you. If you must leave something in your vehicle, hide it out of sight. • Do not leave the vehicle documents in your vehicle. In the unfortunate event of your vehicle being stolen the documents will only help a thief to sell the vehicle. • Do not leave articles on a roof rack as they are particularly vulnerable. If possible, remove them from the rack and lock them inside the vehicle. • Do not leave the spare key in the vehicle keep it in a safe place in your home. • Do not leave a note of your vehicle key number in the vehicle. A thief may break into the vehicle, note the key number and return with a key to enter and drive the vehicle. 5-22 Starting and driving In the winter when it is anticipated that the temperature will drop below 0 C (32 F), check anti-freeze to ensure proper winter protection. For details, see “ENGINE COOLING SYSTEM” in the “8. Maintenance and do-it-yourself” section. Battery If the battery is not fully charged during extremely cold weather conditions, the battery fluid may freeze and damage the battery. To maintain maximum efficiency, the battery should be checked regularly. For details, see "BATTERY'' in the “8. Maintenance and do-ityourself” section. Engine coolant If the vehicle is to be left outside without antifreeze, drain the cooling system by opening the drain valves located under the radiator and on the engine block. Refill before operating the vehicle. See "CHANGING ENGINE COOLANT'' in the “8. Maintenance and do-ityourself” section. CORROSION PROTECTION For additional protection against rust and corrosion, which may be required in some areas, consult your local NISSAN Dealer. Chapter6TOC.fm Page 0 Thursday, April 11, 2013 2:50 PM 6 In case of emergency Flat tyre ...................................................................................... 6-1 Stopping the vehicle........................................................ 6-1 Tools storage location..................................................... 6-1 Preparing the tools and spare tyre............................... 6-2 Blocking the wheels ........................................................ 6-2 Removing the tyre ............................................................ 6-3 Installing the spare tyre ................................................... 6-5 Jump starting ............................................................................ 6-5 Push starting............................................................................. 6-6 Gasoline engine with manual transmission ................ 6-6 If your vehicle overheats ................................................. 6-6 Tow Truck towing .................................................................... 6-7 Towing precautions.......................................................... 6-7 Recommended towing for 2-wheel drive models................................................................................. 6-8 Recommended towing for 4-wheel drive models................................................................................. 6-8 Freeing trapped vehicle .................................................. 6-9 Chapter6TOC.fm Page 1 Thursday, April 11, 2013 2:50 PM Chapter6.fm Page 1 Thursday, April 11, 2013 2:50 PM FLAT TYRE If you have a flat tyre, follow the instructions below. Stopping the vehicle 1 Safely move the vehicle off the road away from traffic. 2 Turn on the hazard warning flasher. 3 Park on a level surface and apply the parking brake. Shift the gearshift lever into the “R” (Reverse) position. WARNING The transfer control lever must be in the “2H”, “4H” or “4L” position to prevent the vehicle from rolling. Never place it in the “N” position. 4 Turn off the engine. 5 Have all passengers get out of the vehicle and stand in a safe place, away from traffic and clear of the vehicle. • Make sure that the parking brake is securely applied. • Be sure to shift the gearshift lever to the “R” (Reverse) position. • Never change tyres when the vehicle is on a slope, icy or a slippery area. This is dangerous. • Never change tyres if oncoming traffic is close to your vehicle. Wait for professional road assistance. • Raise the hood to warn other traffic and to signal professional road assistance personnel that you require assistance. • Place emergency Triangles The storage area for the Jack, Jack rod and Wheel nut wrench is located behind the driver’s seat. For seat tilting procedures, refer to “SEATS” in the “1. Safety - seats, seat belts and supplemental restraint system” section. 1 Jack 2 Jack rod 3 Wheel nut wrench WARNING In case of emergency 6-1 Chapter6.fm Page 2 Thursday, April 11, 2013 2:50 PM PREPARING THE TOOLS AND SPARE TYRE 1 Remove jacking tools from storage area. 2 Remove the spare wheel lock if fitted. 3 Remove the wheel nut wrench from the tool bag. Fit the square end of the jack rod into the square hole of the wheel spanner to form a handle. 4 Find the oval shaped opening under the middle of the tailgate. Pass the T-shaped end of the jack rod through the opening, and direct it towards the spare tyre winch, located directly above the spare tyre. 5 Seat the T-shaped end of the jack rod into the T-shaped opening of the spare tyre winch, and turn the jack rod anti-clockwise to lower the spare tyre. 6 Once the spare tyre is completely lowered, reach under the vehicle, remove the retainer chain and carefully slide the tyre from under the rear of the vehicle. Tightening torque of wheel nuts: 132 Nm (13.5 kg-m, 98 ft-lb) When installing securely. 6-2 In case of emergency the tyre, tighten BLOCKING THE WHEELS WARNING Be sure to block the appropriate wheel as the vehicle may move and could cause personal injury. Place suitable blocks at both the front and back of the wheel diagonally opposite the flat tyre to prevent the vehicle from moving when it is jacked up. Chapter6.fm Page 3 Thursday, April 11, 2013 2:50 PM Type A Type A Type B Type B: REMOVING TYRE Removing the wheel cap (if so equipped). Use a waste cloth to prevent scratches. Type A: 1 Loosen one wheel nut at the “U” shape shown above. 2 Turn the cap anti-clockwise and remove. Replacing the wheel cap. 1 Loosen the wheel nut as illustrated. 2 Turn the wheel cap clockwise so that the “U” shape is opposite the loosened nut. 3 Tighten nut. In case of emergency 6-3 Chapter6.fm Page 4 Thursday, April 11, 2013 2:50 PM jack contacts the vehicle at the jack up point. Align the centre of both the jack head and the jack up point as shown. The jack should be used on level firm ground. 2 Remove the centre cap. 3 Loosen each wheel nut one or two turns by turning anti-clockwise with the wheel nut wrench (jack handle). Do not remove the wheel nuts until the tyre is off the ground. 4 Front wheel of 2WD models and 4WD models Rear wheel of 2WD models Rear wheel of 4WD models Jack-up point • Never jack up the vehicle more than necessary. • Never use blocks on or under the jack. • Do not start or run engine while vehicle is on the jack, as it may cause the vehicle to move. This is especially true for vehicles with limited slip differential carriers. Jacking up and removing tyre WARNING • Never get under the vehicle while it is supported only by the jack; use a vehicle support stand. • Do not allow passengers to stay in the vehicle while it is on the jack. • Remove all loads. • Use the jack provided with your vehicle. Do not use the jack provided with your vehicle on other vehicles. The jack is designed only for lifting your vehicle during a tyre change. • Never run the engine with the wheels off the ground. It may cause the vehicle to move. • Carefully read the caution label attached to the jack body and the following instructions. • Use the correct jack up points; never use any other part of the vehicle for jack support. 6-4 In case of emergency 1 Place the jack directly under the jack-up point as illustrated above so that top of the Carefully raise the vehicle until the tyre clears the ground. Remove the wheel nuts, and then remove the wheel. Do not remove the brake drum with the wheel. Removing the damaged tyre 1 Remove the wheel nuts. 2 Remove the damaged tyre. CAUTION: The tyre is heavy. Be sure that your feet are clear from the tyre and use gloves as necessary to avoid injury. Chapter6.fm Page 5 Thursday, April 11, 2013 2:50 PM • Adjust tyre pressure to the COLD pressure. JUMP STARTING COLD pressure: After vehicle has been parked for 3 hours or more or driven less than 1,6 km (1 mile). COLD tyre pressures are shown on the tyre placard. (See “9. Technical Information” Section for location of placard) 3 WARNING INSTALLING THE SPARE TYRE 1 Clean any mud or dirt from the surface between the wheel and hub. 2 Carefully put the wheel on and tighten the wheel nuts finger tight. 3 With the wheel nut wrench, tighten wheel nuts alternately and evenly until they are tight. 4 Lower the vehicle slowly until the tyre touches the ground. Then, with the wheel nut wrench, tighten the wheel nuts securely in the sequence as illustrated. CAUTION: • • Retighten the wheel nuts when the vehicle has been driven for 1,000 km (600 miles). 5 Install the centre wheel cap securely. 6 Securely store the spare tyre and jacking equipment in the vehicle. CAUTION: Use a battery rated at 12 volts for a booster. 1 Prepare a vehicle with the battery as booster for the vehicle being jump started. Do not allow the vehicles to touch each other. 2 Remove vent caps on the battery (if so equipped). Cover the battery with a moist cloth that has been wrung out. 3 Connect jumper cables in the sequence ( ) as illustrated. WARNING Always make sure that the spare tyre and jacking equipment are properly secured after use. Such items can become dangerous projectiles in an accident or sudden stop. As soon as possible tighten the wheel nuts to the specified torque with a torque wrench. CAUTION: Wheel nut tightening torque: 4 132 Nm (13.5 kg-m, 98 ft-lb) An incorrect connection could result in damage to the charging system. Start the engine of the other vehicle and let it run for a few minutes. Keep the In case of emergency 6-5 Chapter6.fm Page 6 Thursday, April 11, 2013 2:50 PM engine speed at about 2 000 rpm, and start your engine in the normal manner. 5 After starting your engine, carefully disconnect the negative lead and then the positive lead. 6 Replace the vent caps (if so equipped). CAUTION: Be careful not to allow contact of the positive jump lead connector with the vehicle or the negative lead during connection and disconnection. PUSH STARTING IF YOUR VEHICLE OVERHEATS CAUTION: • Catalytic converter equipped models should not be started by pushing since the catalytic converter may be damaged. • Never try to start the vehicle by towing it; when the engine starts, the forward surge could cause the vehicle to collide with the tow vehicle. WARNING To avoid the danger of being burned, never remove the radiator cap while the engine is still hot. 1 Do not stop the engine. 2 Turn off the air conditioner switch. Open all the windows, move the heater or air conditioner temperature control to "maximum hot'' and fan control to "high speed''. 3 Open the hood. If steam or water is coming from the engine, stand clear to prevent getting burned. 4 If engine overheating is caused by climbing a long hill on a hot day, run the engine at a fast idle (approximately 1 500 rpm) until the temperature gauge indicator returns to normal. 5 Visually check drive belts for damage or looseness. Also, check if the cooling fan is running. The radiator hoses and radiator should not leak water. Gasoline engine with Manual transmission (Except catalytic converter equipped models) 1 Turn the ignition key to “ON”. 2 Hold the clutch fully depressed and shift into second or third. Place the transfer in "2H" and freerunning hubs in the "FREE" position (models with manual-lock free-running hub) 3 Hold the accelerator pedal about halfway. 4 Start pushing and when the vehicle reaches a speed of about 16 km/h (10 MPH), turn the ignition key to "ON" and slowly release the clutch pedal to start the engine. Move the vehicle safely off the road, apply the parking brake and move the shift lever to the “N” (neutral) position. WARNING • 6-6 In case of emergency Be careful not to allow your hands, hair or clothing to come into contact with the fan, belts, or other moving parts. Chapter6.fm Page 7 Thursday, April 11, 2013 2:50 PM If coolant is leaking, the cooling fan belt is missing or loose, or the cooling fan does not run, stop the engine. 6 After the engine cools down, check the coolant level in the reservoir tank with the engine running. Add coolant to the reservoir tank if necessary. Have your vehicle repaired at the nearest NISSAN Dealer. TOW TRUCK TOWING CAUTION: When towing your vehicle, local regulations for towing must be followed. Incorrect towing equipment could damage your vehicle. To assure proper towing and to prevent accidental damage to your vehicle, NISSAN recommends that you have a service operator tow your vehicle. It is advisable to have the service operator carefully read the following precautions. • Do not shift the transfer lever to the "4L" position. This will cause damage to the transmission. • Attach safety chains for all towing. Towing precautions • When towing, make sure that the transmission, axles, steering system and power train are in working condition. If any unit is damaged, a dolly or flatbed must be used. • When towing with the front wheels on the ground: Turn the ignition key to the "OFF'' position and secure the steering wheel in a straightahead position with a rope or similar device. Never place the ignition key in the "LOCK'' position. This will result in damage to the steering lock mechanism. Move the shift lever to neutral ("N'' position). • For 4-wheel drive model: Set the free-running hubs to the free position. Move the transfer case shift lever into the "2H" position and the transmission shift lever into the "N" neutral position. In case of emergency 6-7 Chapter6.fm Page 8 Thursday, April 11, 2013 2:50 PM If you have to tow your vehicle with four wheels on the ground or rear wheels on the ground 1 Release the parking brake and move the gearshift lever to the "N" (neutral) position. 2 Observe the following restricted towing speeds and distances: • Speed: Below 95 km/h (60 MPH) • Distance: miles) Less than 800 km (500 If the speed or distance must necessarily be greater, remove the propeller shaft beforehand to prevent damage to the transmission. WARNING Never tow your vehicle from the rear (i.e. backward) with four wheels on the ground as this may cause serious and expensive damage to the transmission. RECOMMENDED TOWING FOR 2-WHEEL DRIVE MODELS NISSAN recommends that your vehicle be towed with the driving (rear) wheels off the ground as illustrated. RECOMMENDED TOWING FOR 4-WHEEL DRIVE MODELS NISSAN recommends that a dolly be used as illustrated when towing your vehicle. If you have to tow your vehicle with four wheels on the ground or front or rear wheels on the ground 6-8 In case of emergency 1 Release the parking brake and move the gearshift lever to the "N" (neutral) position. 2 Observe the following restricted towing speeds and distances. Chapter6.fm Page 9 Thursday, April 11, 2013 2:50 PM • Speed: Below 95 km/h (60 MPH) • Distance: miles) Less than 800 km (500 If the speed or distance must necessarily be greater, remove the propeller shaft beforehand to prevent damage to the transmission. WARNING • Never tow your vehicle from the rear (i.e. backward) with four wheels on the ground as this may cause serious and expensive damage to the transmission. • Be sure to place the transfer case shift lever into the "2H" position and the transmission shift lever into the "N" neutral position if the vehicle is to be towed. Front Rear FREEING TRAPPED VEHICLE • Use the towing hooks only, not other parts of the vehicle. Otherwise, the vehicle body will be damaged. • Use the towing hooks only to free a vehicle stuck in sand, snow, mud, etc. Never tow the vehicle a long distance using only the towing hooks. • The towing hook is under tremendous force when used to free a stuck vehicle. Always pull the cable straight out from the front or rear of the vehicle. Never pull on the hook at a sideways angle. WARNING Do not allow anyone to stand near the towing line during this operation. In case of emergency 6-9 Chapter6.fm Page 10 Thursday, April 11, 2013 2:50 PM 6-10 In case of emergency Chapter7TOC.fm Page 0 Thursday, April 11, 2013 2:51 PM 7 Appearance and care Cleaning exterior...................................................................... 7-1 Washing ............................................................................. 7-1 Removing spots................................................................ 7-1 Waxing................................................................................ 7-1 Glass ................................................................................... 7-1 Chrome Parts .................................................................... 7-1 Plastic parts....................................................................... 7-1 Cleaning interior....................................................................... 7-2 Glass ................................................................................... 7-2 Seat belts ........................................................................... 7-2 Floor mats........................................................................... 7-2 Corrosion protection............................................................... 7-2 Most common factors contributing to vehicle corrosion............................................................................. 7-2 Environmental factors influence the rate of corrosion............................................................................. 7-2 To protect your vehicle from corrosion........................ 7-3 Chapter7TOC.fm Page 1 Thursday, April 11, 2013 2:51 PM Chapter7.fm Page 1 Thursday, April 11, 2013 2:50 PM CLEANING EXTERIOR CAUTION: In order to maintain the appearance of your vehicle, it is important to take proper care of it. • In the following cases, please wash your vehicle as soon as possible to protect the paint surface. • After a rainfall to prevent possible damage from acid rain • After driving on coastal roads • When things such as soot, bird droppings, tree sap, metal particles or bugs get on the paint surface • When dust or mud builds up on the surface Whenever possible, store or park your vehicle inside a garage or in a covered area. When it is necessary to park outside, park in a shady area or protect the vehicle with a body cover. Be careful not to scratch the paint surface when putting on or removing the body cover. WASHING Wash dirt off with a wet sponge and plenty of water. Clean the vehicle thoroughly using a mild soap or detergent (a special vehicle soap or general purpose dishwashing liquid) mixed with clean, lukewarm (never hot) water. • • Do not use strong household soap, strong chemical detergents, gasoline or solvents. Do not wash your vehicle in the direct sunlight or while the vehicle body is hot, as the surface may become water-spotted. Avoid using tigh-napped or rough cloths, such as washing mitts. Care must be taken when removing cakedon dirt or other foreign substances so that the paint surface is not scratched or damaged. Your NISSAN Dealer can assist you in choosing the proper product. • Wax your vehicle only after a thorough washing. Follow the instructions supplied with the wax. • Do not use a wax containing any abrasives, cutting compounds or cleaners that may damage the vehicle finish. • If the surface does not polish easily, use a "road tar'' remover and wax again. Machine compounding or aggressive polishing on a base coat/clear coat paint finish may dull the finish or leave swirl marks. Rinse the vehicle thoroughly with plenty of clean water. Only use black wax or black shoe polish on black urethane or polypropylene bumpers. A damp chamois can be used to dry the vehicle to avoid water spots. GLASS REMOVING SPOTS Remove tar and oil spots, industrial dust, insects, and tree sap as quickly as possible from the surface of the paint to avoid lasting damage or staining. Special cleaning products are available at your NISSAN Dealer or any automotive accessory store. WAXING Regular waxing protects the paint surface and helps retain new vehicle appearance. After waxing, polishing is recommended to remove built-up residue and to avoid a "weathered'' appearance. Use glass cleaner to remove smoke and dust film from the glass surfaces. It is normal for glass to become coated with a film after the vehicle is parked in the hot sun. Glass cleaner and a soft cloth will easily remove this film. CHROME PARTS Clean all chrome parts regularly with a nonabrasive chrome polish to maintain the finish. PLASTIC PARTS Plastic parts can be cleaned with a mild soap solution. If the dirt cannot be easily removed, use a plastic cleaner. Do not use any solvents. Appearance and care 7-1 Chapter7.fm Page 2 Thursday, April 11, 2013 2:50 PM CLEANING INTERIOR SEAT BELTS Occasionally remove loose dust from the interior trim and seats using a vacuum cleaner or soft brush. Wipe the vinyl and leather surfaces with a clean, soft cloth dampened in mild soap solution, then wipe clean with a dry soft cloth. Before using any fabric protector, read the manufacturer's recommendations. Some fabric protectors contain chemicals that may stain or bleach the seat material. The seat belts can be cleaned by wiping them with a sponge dampened in a mild soap solution. Allow the belts to dry completely before using them. Do not allow wet belts to roll up in the retractor. NEVER use bleach, dye, or chemical solvents since these may severely weaken the seat belt webbing. • Never use benzine, thinners, or any similar fluids. • The leather seats should be regularly coated with a leather wax like saddle soap. Never use car wax. • Never use fabric protectors unless recommended by the manufacturer. The use of Genuine NISSAN floor mats can extend the life of your vehicle carpet and make it easier to clean the interior. No matter what mats are used, be sure they are fitted for your vehicle and are properly positioned in the footwell to prevent interference with pedal operation. Mats should be maintained with regular cleaning and replaced if they become excessively worn. GLASS Use glass cleaner to remove smoke and dust film from the glass surfaces. It is normal for glass to become coated with a film after the vehicle is parked in the hot sun. Glass cleaner and a soft cloth will easily remove this film. When cleaning the inside of the window, do not use sharpedged tools, abrasive cleaners or chlorine based disinfectant cleaners. They could damage electrical conductors or rear window defogger elements. 7-2 Appearance and care FLOOR MATS CORROSION PROTECTION MOST COMMON FACTORS CONTRIBUTING TO VEHICLE CORROSION 1 The accumulation of moisture-retaining dirt and debris in body panel sections, cavities, and other areas. 2 Damage to paint and other protective coatings caused by gravel and stone chips or minor traffic accidents. ENVIRONMENTAL FACTORS INFLUENCE THE RATE OF CORROSION Moisture Accumulation of sand, dirt and water on the vehicle body underside can accelerate corrosion. Wet floor coverings will not dry completely inside the vehicle, and should be removed for drying to avoid floor panel corrosion. Relative humidity Corrosion will be accelerated in areas of high relative humidity, especially those areas where the temperatures stay above freezing and where atmospheric pollution exists. Chapter7.fm Page 3 Thursday, April 11, 2013 2:50 PM Temperature A temperature increase will accelerate the rate of corrosion to those parts which are not well ventilated. For additional protection against rust and corrosion, which may be required in some areas, consult your local NISSAN Dealer. Air pollution Industrial pollution and the presence of salt in the air in coastal areas will accelerate the corrosion process. TO PROTECT YOUR VEHICLE FROM CORROSION • Wash and wax your vehicle often to keep the vehicle clean. • Always check for minor damage to the paint and repair it as soon as possible. • Keep drain holes at the bottom of the doors and tailgate open to avoid water accumulation. • Check the underbody for accumulation of sand, dirt or salt. If present, wash with water as soon as possible. • NEVER remove dirt, sand or other debris from the passenger compartment by washing it out with a hose. Remove dirt with a vacuum cleaner or broom. • Never allow water or other liquids to come in contact with electronic components inside the vehicle. In winter, the underbody cleaned periodically. must be Appearance and care 7-3 Chapter7.fm Page 4 Thursday, April 11, 2013 2:50 PM 7-4 Appearance and care Chapter8TOC.fm Page 0 Thursday, April 11, 2013 2:52 PM 8 Maintenance and do-it-yourself Maintenance requirements .................................................... 8-1 Scheduled maintenance ................................................. 8-1 General maintenance ...................................................... 8-1 Where to go for service .................................................. 8-1 General maintenance.............................................................. 8-1 Explanation of general maintenance items ................. 8-1 Maintenance precautions ............................................... 8-2 Engine compartment check locations KA20 gasoline engine..................................................... 8-4 KA24 gasoline engine..................................................... 8-5 YD25DDTi diesel engine................................................ 8-6 Engine cooling system ........................................................... 8-7 Checking engine coolant level ...................................... 8-7 Changing engine coolant ............................................... 8-8 Engine oil................................................................................... 8-9 Checking engine oil level................................................ 8-9 Facts about oil and oil consumption ..........................8-10 Changing engine oil.......................................................8-10 Changing engine oil filter..............................................8-12 Protect the environment ...............................................8-13 Fuel filter...........................................................................8-13 Draining water.................................................................8-13 Bleeding the fuel system ..............................................8-14 Drive belts ...............................................................................8-15 Spark plugs.............................................................................8-15 Spark plug replacement ...............................................8-15 Recommended heat range ..........................................8-16 Brake ........................................................................................8-16 Checking parking brake ................................................8-16 Checking brake pedal....................................................8-16 Brake booster ..................................................................8-16 Brake and clutch fluid ...........................................................8-17 Power steering fluid ..............................................................8-18 Air cleaner filter ......................................................................8-18 Wiper blades ..........................................................................8-20 Cleaning............................................................................8-20 Replacement....................................................................8-20 Windshield washer nozzle ............................................8-21 Window washer fluid ............................................................8-21 Battery ......................................................................................8-22 Vehicle battery.................................................................8-22 Fuses ........................................................................................8-24 Engine compartment......................................................8-24 Passenger compartment...............................................8-24 Lights ........................................................................................8-25 Headlights ........................................................................8-25 Front clearance light & Front turn signal lights ........8-26 Other lights ......................................................................8-27 Light locations .................................................................8-28 Wheels and tyres...................................................................8-30 Tyre inflation pressure ...................................................8-30 Tyre rotation .....................................................................8-30 Tyre wear and damage .........................................................8-30 Tyre age ...................................................................................8-30 Chapter8TOC.fm Page 1 Thursday, April 11, 2013 2:52 PM Changing tyres and wheels.................................................8-31 4-wheel drive model .............................................................8-31 Wheel balance .......................................................................8-31 Care of wheels .......................................................................8-31 4X4 Clutch housing ..............................................................8-31 Chapter8.fm Page 1 Thursday, April 11, 2013 2:51 PM MAINTENANCE REQUIREMENTS Your new NISSAN has been designed to have minimum maintenance requirements with longer service intervals to save you both time and money. However, some day-to-day and regular maintenance is essential to maintain your NISSAN's good mechanical condition, as well as its emission and engine performance. It is the owner's responsibility to make sure that scheduled maintenance, as well as general maintenance, is performed. As a vehicle owner, you are the only one who can ensure that your vehicle receives the proper maintenance care. You are a vital link in the maintenance chain. SCHEDULED MAINTENANCE For your convenience, the required schedule maintenance items are described and listed in a separate maintenance booklet. You must refer to that booklet to ensure that necessary maintenance is performed on your NISSAN at regular intervals. GENERAL MAINTENANCE General maintenance includes those items that should be checked during normal day-today operation of the vehicle. They are essential if your vehicle is to continue to operate properly. It is your responsibility to perform these procedures regularly as prescribed. Performing general maintenance checks require minimal mechanical skill and only a few general automotive tools. These checks or inspections can be done by yourself, a qualified technician, or if you prefer, your NISSAN Dealer. WHERE TO GO FOR SERVICE If maintenance service is required or your vehicle appears to malfunction, have the systems checked and tuned by an authorised NISSAN Dealer. NISSAN technicians are well-trained specialists and are kept up to date with the latest service information through technical bulletins, service tips, and training programs. They are completely qualified to work on NISSAN vehicles before they work on your vehicle, rather than after they have worked on it. You can be confident that your NISSAN Dealer's service department performs the best job to meet the maintenance requirement on your vehicle - in a reliable and economic way. GENERAL MAINTENANCE During the normal day-to-day operation of the vehicle, general maintenance should be performed regularly as prescribed in this section. If you detect any unusual sounds, vibration or smell, be sure to check for the cause or have your NISSAN Dealer do it promptly. In addition, you should notify your NISSAN Dealer if you think that repairs are required. When performing any checks or maintenance work, closely observe "MAINTENANCE PRECAUTIONS" later in this section. EXPLANATION OF GENERAL MAINTENANCE ITEMS Additional information on the following items with "*" is found later in this section. Outside the vehicle The maintenance items listed here should be performed from time to time, unless otherwise specified. Doors and engine hood: Check that all doors and the engine hood operate properly. Also ensure that all latches lock securely. Lubricate hinges and latches if necessary. Make sure that the secondary latch keeps the hood from opening when the primary latch is released. Maintenance and do-it-yourself 8-1 Chapter8.fm Page 2 Thursday, April 11, 2013 2:51 PM Lights*: Steering wheel: MAINTENANCE PRECAUTIONS Make sure that the headlights, stop lights, tail lights, turn signal lights and other lights are all operating properly and installed securely. Also check headlight aim. Check for change in the steering conditions, such as excessive free play, hard steering or strange noises. When performing any inspection or maintenance work on your vehicle, always take care to prevent serious accidental injury to yourself or damage to the vehicle. The following are general precautions which should be closely observed. Tyres*: Check the pressure with a gauge periodically when at a service station (including the spare) and adjust to the specified pressure if necessary. Check carefully for damage, cuts or excessive wear. Tyre rotation*: Tyres should be rotated frequently. The timing for tyre rotation may vary according to your driving habits and road surface conditions. Windshield wiper blades*: The life of windscreen wiper blades is dependent on the amount of use and climatic conditions. For safety reasons these items should be replaced when wear impairs their function to clear the windscreen effectively. Inside the vehicle The maintenance items listed here should be checked on a regular basis, such as when performing periodic maintenance, cleaning the vehicle, etc. Seat belts: Check that all parts of the seat belts system, (e.g. buckles, anchors, adjusters and retractors) operate properly and smoothly and are installed securely. Check the belt webbing for cuts, fraying, wear or damage. 8-2 Maintenance and do-it-yourself Warning/indicator lights and buzzers/ chimes: Make sure that all warning/indicator lights and buzzers/chimes are operating properly. • Park the vehicle on a level surface, apply the parking brake securely and block the wheels to prevent the vehicle from moving. For a manual transmission, move the shift lever to neutral. • Do not work under the hood while the engine is hot. Turn off the engine and wait until it cools down. • Be sure to turn the ignition key to the "OFF'' or "LOCK'' position. • When the ignition key is in the "ON'' or "ACC'' position, the cooling fan may start to operate suddenly even when the engine is not running. • If you must work with the engine running, keep your hands, clothing, hair and tools away from moving fans, belts and any other moving parts. • It is advisable to remove ties and any jewelry, such as rings, watches, etc. before working on your vehicle. • If you must run the engine in an enclosed space such as a garage, be sure there is proper ventilation for exhaust gases. Under the hood and vehicle The maintenance items listed here should be checked periodically, e.g. each time you check the engine oil or refuel. Battery*: Check the fluid level in each cell. It should be between the MAX and MIN lines. Brake and clutch fluid level*: Make sure that the brake and clutch fluid level is between the MAX and MIN lines on the reservoir. Engine coolant level*: Check the coolant level when the engine is cold. Engine oil level*: Check the level after parking the vehicle on a level spot and turning off the engine. Windshield washer fluid*: Check that there is adequate fluid in the tank. Chapter8.fm Page 3 Thursday, April 11, 2013 2:51 PM • Never get under the vehicle while it is supported only by a jack. If it is necessary to work under the vehicle, support it with safety stands. You should be aware that incomplete or improper servicing may result in operating difficulties or excessive emissions and could affect your warranty coverage. • Keep smoking materials, flame and sparks away from fuel and battery. If in doubt about any servicing, have it done by your NISSAN Dealer. • Never connect or disconnect either the battery or any transistorized component connector while the ignition is on. • Always apply the parking brake and block the wheels to prevent the vehicle from moving. • On gasoline engine models with the multiport fuel injection (MFI) system, the fuel filter or fuel lines should be serviced by a NISSAN dealer because the fuel lines are under high pressure even when the engine is off. • Failure to follow these or other common sense guidelines may lead to serious injury or vehicle damage. • Improperly disposed motor oil and/or other vehicle fluids can hurt the environment. Always conform to local regulations for disposal of vehicle fluid. • Avoid direct contact with used engine oil. This "8. Maintenance and do-it-yourself'' section gives instructions regarding only those items which are relatively easy for an owner to perform. Maintenance and do-it-yourself 8-3 Chapter8.fm Page 4 Thursday, April 11, 2013 2:51 PM ENGINE COMPARTMENT CHECK LOCATIONS KA20 GASOLINE ENGINE 1. Fuse box 2. Power steering fluid reservoir 3. Brake fluid reservoir* 4. Clutch fluid reservoir* 5. Engine oil dipstick 6. Battery 7. Engine coolant reservoir 8. Radiator cap 9. Engine oil filler cap 10. Windshield washer reservoir 11. Air cleaner 12. Air intake duct *:This layout is for RHD models. 8-4 Maintenance and do-it-yourself Chapter8.fm Page 5 Thursday, April 11, 2013 2:51 PM KA24 GASOLINE ENGINE 1. Fuse box 2. Power steering fluid reservoir 3. Brake fluid reservoir* 4. Clutch fluid reservoir* 5. Engine oil dipstick 6. Battery 7. Engine coolant reservoir 8. Radiator cap 9. Engine oil filler cap 10. Windshield washer reservoir 11. Air cleaner 12. Air intake duct *:This layout is for LHD models. For KA24 RHD models, these components are located on the opposite side. Maintenance and do-it-yourself 8-5 Chapter8.fm Page 6 Thursday, June 18, 2015 8:54 AM vaORaaqá=afbpbi=bkdfkb NK cìëÉ=Äçñ OK _ê~âÉ=ÑäìáÇ=êÉëÉêîçáêG PK `äìíÅÜ=ÑäìáÇ=êÉëÉêîçáêG QK båÖáåÉ=çáä=ÇáéëíáÅâ RK cìÉä=ÑáäíÉêGLGG SK ^áê=ÅäÉ~åÉê TK _~ííÉêó UK båÖáåÉ=Åççä~åí=êÉëÉêîçáê VK mçïÉê=ëíÉÉêáåÖ=ÑäìáÇ=êÉëÉêîçáê NMK o~Çá~íçê=Å~é NNK båÖáåÉ=çáä=ÑáääÉê=Å~é NOK táåÇëÜáÉäÇ=ï~ëÜÉê=êÉëÉêîçáê GW= qÜáë= ä~óçìí= áë= Ñçê= oea= ãçÇÉäëK= cçê= iea ãçÇÉäëI= íÜÉëÉ= ÅçãéçåÉåíë= ~êÉ= äçÅ~íÉÇ= çå íÜÉ=çééçëáíÉ=ëáÇÉK GGWNK oea= ãçÇÉäë= ïáíÜ= ÅçãÄáåÉÇ=ÑìÉä=ÑáäíÉêK ^_pW= páåÖäÉ OK oea= ãçÇÉäë= ïáíÜçìí= ^_pW= páåÖäÉ ÅçãÄáåÉÇ=ÑìÉä=ÑáäíÉêK PK iea= ~ää= ãçÇÉäëW= páåÖäÉ= ÅçãÄáåÉÇ= ÑìÉä ÑáäíÉêK 8-6 Maintenance and do-it-yourself Chapter8.fm Page 7 Thursday, April 11, 2013 2:51 PM ENGINE COOLING SYSTEM WARNING • • Never remove the radiator cap when the engine is hot. Serious burns could be caused by high-pressure fluid escaping from the radiator. Wait until the engine and radiator cool down. See precautions in "IF YOUR VEHICLE OVERHEATS'' found in the "6. In case of emergency'' section. Engine coolant is poisonous and should be stored carefully in marked containers out of the reach of children. The engine cooling system is filled at the factory with a high-quality, year-round and extended life engine coolant. The high quality engine coolant contains the specific solutions effective for the anti-corrosion and the antifreeze function. Therefore, additional cooling system additives are not necessary. CAUTION: When adding or replacing coolant, be sure to use only a NISSAN Genuine Engine Coolant or equivalent in its quality with the proper mixture ratio. Examples are shown below: Outside temperature down to Composition ºC (°F) Engine coolant (concentrated) Demineralized water or distilled Water -15 (5) 30% 70% -35 (-30) 50% 50% The use of other types of engine coolant may damage your cooling system. The radiator is equipped with a pressure cap. Use a NISSAN genuine cap when replacement is required. CHECKING ENGINE COOLANT LEVEL Coolant reservoir Check the coolant level in the reservoir tank when the engine is cold. If the coolant level is below "MIN'', add coolant up to the "MAX'' level. If the reservoir tank is empty, check the coolant level in the radiator when the engine is cold. If there is insufficient coolant in the radiator, fill the radiator with coolant up to the filler opening and also add it to the reservoir tank up to the "MAX'' level. CAUTION: If the cooling system frequently requires coolant, have it checked by your NISSAN Dealer. Maintenance and do-it-yourself 8-7 Chapter8.fm Page 8 Thursday, April 11, 2013 2:51 PM Watch the coolant temperature gauge for signs of overheating. 5 Stop the engine. After it completely cools down, refill the radiator up to the filler opening. Fill the reservoir tank up to the "MAX'' level. 6 Check the drain plug leakage. for any sign of 7 Recheck the coolant level after the vehicle has been driving for a day. CHANGING ENGINE COOLANT Your NISSAN Dealer should perform major cooling system repairs. The service procedures can be found in the appropriate NISSAN Service Manual. Improper servicing can result in reduced heater performance and engine overheating. WARNING • To avoid the danger of being scalded, never change the coolant when the engine is hot. • Never remove the radiator cap when the engine is hot. Serious burns could be caused by high-pressure fluid escaping from the radiator. 8-8 Maintenance and do-it-yourself 1 Open the drain plug at the bottom of the radiator and the radiator cap . • Be careful not to allow coolant to contact drive belts. • Waste coolant must be disposed of properly. Check your local regulations. 2 Close the radiator drain plug securely. 3 See the "Technical information'' section for cooling system capacity. Fill the radiator slowly with the proper mixture of coolant and water. Fill the reservoir tank up to the "MAX'' level. Then install the radiator cap . 4 Start the engine, and warm it up until it reaches normal operating temperature. Then race the engine 2 or 3 times under no load. Chapter8.fm Page 9 Thursday, April 11, 2013 2:51 PM ENGINE OIL CHECKING ENGINE OIL LEVEL 1 Park the vehicle on a level surface and apply parking brake. 2 Run the engine until it reaches operating temperature. 3 Turn off the engine. Wait at least 10 minutes for the oil to drain back into the oil pan. 4 Remove the dipstick and wipe it clean. Reinsert it all the way. 5 Remove the dipstick again and check the oil level. It should be between the "H'' and "L'' marks. If the oil level is below the "L'' mark, remove the oil filler cap and pour recommended oil through the opening. Do not overfill. YD25DDTi engine 6 Recheck oil level with dipstick. CAUTION: • Oil level should be checked regularly. Operating with insufficient amount of oil can damage the engine, and such damage is not covered by warranty. • It is normal to add some oil between oil maintenance intervals or during the run-in period, depending on the severity of operating conditions. KA20/KA24 engine Maintenance and do-it-yourself 8-9 Chapter8.fm Page 10 Thursday, April 11, 2013 2:51 PM FACTS ABOUT OIL AND OIL CONSUMPTION Diesel combustion engines depend upon oil to lubricate cylinder walls, pistons and rings. With each stroke of the piston, a thin film of oil is left on the cylinder walls and on the firing stroke the combustion flame burns it. If an engine burned just one drop of oil on every firing stroke, it would need approximately 400 ml per kilometre/mile. Consumption of this amount is unheard of in the internal combustion engine, but all efficient engines do, however, use some oil to prevent rapid engine wear. The rate of consumption depends upon the quality and viscosity of the oil, engine rpm, the temperature and the amount of dilution and oxidation in the crankcase. If the engine oil is checked it may indicate full on the dipstick, but this could be misleading due to the vehicle being operated for 2,000 km (1,243 miles) or more in city or congested road conditions, which causes a build up of condensation and unburned fuel in the combustion chamber, which passes into the crankcase, and thus gives a false dipstick reading. If the vehicle should then be driven at high engine rpm for a fairly long journey the unburned fuel will boil off rapidly and the vehicle then appears to consume oil. High speed operating conditions will greatly accelerate oil consumption due to the inability 8-10 Maintenance and do-it-yourself of the piston rings to scavenge the oil completely at higher rpm and high engine temperature. Automobile manufacturers have proved in tests that an internal combustion engine uses seven times the quantity of oil at 100 km/h (62 MPH) than it does at 60 km/h 37 MPH). No standard rate of consumption can be established because of the varying combinations and conditions and as a guide we consider the following as normal oil consumption on gasoline engines. Oil consumption of up to 1,5 litres per 1,000 km (621 miles) during the first 10,000 km (6,214 miles) of vehicle life is considered normal, as it takes approximately 10 000 km (6,214 miles) for the piston rings to bed in to the cylinder walls, and the normal consumption should then drop to approximately 1 litre per 1 000 km (621 miles). CHANGING ENGINE OIL WARNING Used oil must not be poured into the ground, canals, rivers, etc. It should be disposed of at a rubbish tip having proper facilities. We recommend having your oil changed by a NISSAN Dealer. 1 Park the vehicle on a level surface and apply the parking brake. 2 Run the engine until it reaches operating temperature and then turn it off. Wait for more than 10 minutes. 3 Place a large drain pan under the drain plug. 4 Remove the oil filler cap . 5 Remove the drain plug with a wrench and completely drain the oil. If oil filter is to be changed, remove and replace it at this time. See "CHANGING OIL FILTER'' in the “8. Maintenance and do-ityourself” section. WARNING Be careful not to burn yourself, as the engine oil is hot. CAUTION: Waste oil must be disposed of properly. Check your local regulations. 6 Clean and re-install the drain plug with a new washer. Securely tighten the drain plug with a wrench. Do not use excessive force. Chapter8.fm Page 11 Thursday, April 11, 2013 2:51 PM YD25DDTi engine KA20/KA24 (2WD) engine Drain plug tightening torque: KA24 (4WD) engine WARNING Gasoline engines and YD25DDTi engine 29 to 39 Nm (3.0 to 4.0 kg-m, 22 to 29 ft-lb) • Prolonged and repeated contact with used engine oil may cause skin cancer. 7 Refill engine with recommended oil and install the cap securely. See the "9. Technical Information'' section for refill capacity. 8 Start the engine. Check for leakage around the drain plug. Correct as required. 9 Turn the engine off and wait several minutes. Check the oil level with the dipstick. Add engine oil if necessary. • Try to avoid direct skin contact with used oil. If skin contact is made, wash thoroughly with soap or hand cleaner as soon as possible. Keep used engine oil out of reach of children. Maintenance and do-it-yourself 8-11 Chapter8.fm Page 12 Thursday, April 11, 2013 2:51 PM Be sure to remove any old rubber gasket remaining on the mounting surface of the engine. 5 Coat the rubber gasket on the new filter with clean engine oil. 6 Screw in the oil filter until a slight resistance is felt, then tighten additionally more than 2/3 turn. 7 Start the engine and check for leakage around the oil filter. Correct as required. KA20/KA24 engine CHANGING ENGINE OIL FILTER A used oil filter should be disposed of at a rubbish tip having proper facilities. We recommend having your oil filter changed by a NISSAN Dealer. Except YD25DDTi engine 1 Park the vehicle on a level surface and apply the parking brake. 2 Turn the engine off. 3 Loosen the oil filter with an oil filter wrench. Remove the oil filter by turning it by hand. Be careful not to burn yourself, as the engine oil may be hot. 4 Wipe the engine oil filter mounting surface with a clean rag. 8-12 Maintenance and do-it-yourself 8 Turn the engine off and wait several minutes. Check the oil level. Add engine oil if necessary. YD25DDTi engine YD25DDTi type engines Removal: 1 Turn the engine off. 2 Using a socket wrench, loosen the filter body. 3 Catch the oil in a container or with waste rags. 4 Remove the filter body and remove the oil filter element. 5 Remove the O-ring from the filter body. Chapter8.fm Page 13 Thursday, April 11, 2013 2:51 PM Securely push the oil filter element into the filter body. FUEL FILTER (Diesel engine) 3 Install the filter body to the oil filter bracket. Tightening torque for YD25DDTi type: 15 to 21 N.m (1.6 to 2.1 kg-m, 11 to 15 ft-lb)) After the engine has been warmed up, make sure there are no oil leaks. PROTECT THE ENVIRONMENT Push the O-ring with your hand to separate it from the filter body . Then grab and hold of it with your fingertips and remove it. It is illegal to pollute drains, water courses and soil. Use authorized waste collection facilities, including civic amenity sites and garages providing facilities for disposal of used oil and used oil filters. If in doubt, contact your local authority for advice on disposal. Do not use a wire or screwdriver will damage the filter body. The regulations concerning the pollution of the environment will vary from country to country. Type A Combined type for RHD ABS models DRAINING WATER If engine oil gets on the engine or vehicle body, wipe it completely clean. If the water-in-fuel warning light (YD25DDTi engines) or the malfunction indicator light (YD25DDTi engine) comes on (and a chime sound, if so equipped) while the engine is running, drain the water in the fuel filter as follows: Installation: Type A as it 1 Remove foreign materials thoroughly from inside the filter body and O-ring mounting portions (on the body and bracket sides). 2 Install a new oil filter element and a new O-ring to the filter body. 1 Place a container under the fuel filter. 2 Loosen the drain valve 4 to 5 turns to drain the water. To avoid dropping it, do not loosen the drain valve too much. If water does not drain properly, move the priming pump up and down. 3 After the water has been completely drained, close the drain valve . Maintenance and do-it-yourself 8-13 Chapter8.fm Page 14 Thursday, April 11, 2013 2:51 PM 4 Bleed any air from the fuel system. (See "BLEEDING THE FUEL SYSTEM" later in this section). Type B Seperate type BLEEDING THE FUEL SYSTEM Type B 1 Place a container under the drain valve. 2 Loosen the drain support screw and drain valve 4 to 5 turns to drain the water. To avoid dropping it, do not loosen the drain valve too much. 3 After the water has been completely drained, close the drain valve and drain support screw . 4 Bleed any air from the fuel system. (Refer to “BLEEDING THE FUEL SYSTEM” later in this section.) NISSAN recommends draining water in the fuel filter according to the maintenance intervals shown in a separate maintenance booklet. 8-14 Maintenance and do-it-yourself Bleed air out of the fuel system after refilling an empty fuel tank by the following action: 1 Move the priming pump up and down until a resistance occurs, then stop the pumping. 2 Crank the engine until the engine starts. Do not crank the engine for more than 30 seconds. 3 If the engine does not start, stop cranking and repeat step 1 above. 4 If the engine does not operate smoothly after it has started, race it two or three times. Chapter8.fm Page 15 Thursday, April 11, 2013 2:51 PM DRIVE BELTS SPARK PLUGS Be sure the ignition key is "OFF''. 1 Visually inspect each belt for signs of unusual wear, cuts, fraying or looseness. If the belt is in poor condition or loose, have it replaced or adjusted by your NISSAN Dealer. 2 Have the belts checked regularly for condition and tension in accordance with the maintenance intervals shown in a separate maintenance booklet. WARNING Be sure the engine and ignition switch are off and that the parking brake is engaged securely. CAUTION: • Be sure to use the correct socket to remove the spark plugs. An incorrect socket can cause damage to the spark plugs. • Always replace spark plugs with recommended or equivalent ones. SPARK PLUG REPLACEMENT Replace the spark plugs according to the maintenance log shown in a separate maintenance booklet. CAUTION: Be sure the ignition key is "OFF". 1 Disconnect spark plug cables. Keep track of the original cable location. When disconnecting, always hold the boots - not the cables . Mark all cables to identify. 2 Remove spark plugs with a spark plug wrench. Maintenance and do-it-yourself 8-15 Chapter8.fm Page 16 Thursday, April 11, 2013 2:51 PM BRAKE 3 Check each new spark plug gap with a feeler gauge . (The spark plug gap is shown in the "Technical Information'' section.) Adjust it as required. 4 Install spark plugs. CAUTION: When installing a plug, turn it in two or three turns by hand and then tighten with a spark plug wrench. Be careful not to over-tighten it. Spark plug tightening torque: 20 to 29 Nm (2.0 to 3.0 kg-m, 14 to 22 ft-lb) 5 Reconnect the spark plug cables to their original positions. 8-16 Maintenance and do-it-yourself RECOMMENDED HEAT RANGE CHECKING PARKING BRAKE The factory-installed spark plugs on your vehicle are designed to meet normal driving conditions. If your vehicle is operated under either of the following conditions, it is recommended that optional spark plugs of the proper heat range be installed. Periodically check the holding ability of the parking brake by parking on a steep hill and holding the vehicle by using only the parking brake. If it does not hold satisfactorily, see your NISSAN Dealer. 1 When the vehicle is used primarily for short distance travel, so that the engine does not run long enough to reach its normal operating temperature, use hottype spark plugs. 2 When the vehicle is frequently operated with throttle wide open for long periods of time, use cold-type spark plugs. For spark plug types, please consult your NISSAN dealer. CHECKING BRAKE PEDAL If the brake pedal suddenly goes down further than normal, the pedal feels "spongy'' or the vehicle seems to take longer to stop, see your NISSAN Dealer immediately. BRAKE BOOSTER Check the brake booster function with the following steps: 1 With the engine off, depress the brake pedal several times to make sure that the pedal travel distance does not change. 2 While depressing the brake pedal, start the engine. The pedal height should drop a little. 3 With the brake pedal depressed, stop the engine. Keeping the pedal depressed for about 30 seconds, the pedal height should not change. Chapter8.fm Page 17 Thursday, April 11, 2013 2:51 PM BRAKE AND CLUTCH FLUID 4 Run the engine for one minute without depressing the brake pedal, then turn it off. Depress the brake pedal several times. The pedal travel distance will decrease gradually with each depression as the vacuum is released from the booster. • Do not spill the fluid on painted surfaces. This will damage the paint. If fluid is spilled, wash with water. WARNING • Use only new fluid. Old, inferior, or contaminated fluid may damage the brake and clutch systems. The use of improper fluids can damage the clutch and brake systems and affect the vehicle's stopping ability. • Brake and clutch fluids are poisonous and should be stored carefully in marked containers out of the reach of children. If the brakes do not operate properly, see your NISSAN dealer. Check the fluid levels in the brake fluid! reservoir and clutch fluid reservoir . If! the fluid is below the MIN line or the warning! light comes on, add fluid up to the MAX line. If fluid must be added frequently, the system! should be thoroughly checked by your! NISSAN Dealer. CAUTION: • NISSAN recommends that refilling and checking the brake and clutch systems be left to a NISSAN Dealer who will have the necessary brake and clutch fluids and technical knowledge. Maintenance and do-it-yourself 8-17 Chapter8.fm Page 18 Thursday, April 11, 2013 2:51 PM POWER STEERING FLUID AIR CLEANER YD25 Diesel engines Check the fluid level in the reservoir. The fluid level should be checked using the "HOT'' range on the fluid reservoir at fluid temperatures of 50ºC to 80ºC (122 to 176 °F) or using the "COLD'' range on the fluid reservoir at fluid temperatures of 0ºC to 30ºC (32 to 86°F). CAUTION: • Do not overfill. • Use only "Type DEXRON TMIIE' , or DEXRON TMIII' equivalent. WARNING Power steering fluid is poisonous and should be stored carefully in marked containers out of the reach of children. 8-18 Maintenance and do-it-yourself KA20 Gasoline engines KA24 Gasoline engines Chapter8.fm Page 19 Thursday, April 11, 2013 2:51 PM VISCOUS PAPER TYPE The filter element should not be cleaned and reused as it is given a special treatment. We recommend it be replaced according to the maintenance intervals shown in a separate maintenance booklet. When replacing the filter, wipe the inside of the air cleaner housing and the cover with a damp cloth. DRY PAPER TYPE Check the filter element to see if ti is dirty. If it is dirty, shake the element to remove dust. We recommend it be cleaned or replaced according to the maintenance intervals shown in a separate maintenance booklet. When cleaning or replacing the filter, wipe the inside of the air cleaner housing and the cover with a damp cloth. WARNING Operating the engine with the air cleaner filter off can cause you or others to be burned. The air cleaner not only cleans the intake air, it also stops flame if the engine backfires. If it is not here and the engine backfires, you could be burned. Don’t drive with it off and be careful working on the engine with the air cleaner off. CYCLONE AIR CLEANER (if so equipped) Periodically pinch the rubber cap located under the cyclone to remove dust from the cyclone. Maintenance and do-it-yourself 8-19 Chapter8.fm Page 20 Thursday, April 11, 2013 2:51 PM WIPER BLADES REPLACEMENT 1 Pull the wiper arm up. 2 Push the lock pin wiper blade . , then remove the 3 Insert the new wiper blade to the wiper arm until a click sounds. CAUTION: Left-hand drive models Right-hand drive models CLEANING If your windshield is not clear after using the windshield washer or if the wiper blade chatters when running, wax or other material may be on the blade or windshield. Clean the outside of the windshield with a washer solution or a mild detergent. Your 8-20 Maintenance and do-it-yourself windshield is clean if beads do not form when rinsing with clear water. Clean the blade by wiping it with a cloth soaked in a washer solution or a mild detergent. Then rinse the blade with clear water. If your windshield is still not clear after cleaning the blades and using the wiper, replace the blades. • After wiper blade replacement, return the wiper arm to its original position. Otherwise it may be damaged when the engine hood (bonnet) is opened. • Make sure the wiper blade contacts the glass, otherwise the arm may be damaged from wind pressure. Chapter8.fm Page 21 Thursday, April 11, 2013 2:51 PM WINDOW WASHER FLUID Check the fluid level in the reservoir tank and add fluid if necessary. Add a washer solvent to the water for better cleaning. In the winter season, add a window washer anti-freeze. Follow the manufacturer’s instructions for the mixture ratio. CAUTION: WINDSHIELD WASHER NOZZLE If you wax the surface of the hood, be careful not to let wax get into the washer nozzle. This may cause clogging or improper windshield washer operation. If wax gets into the nozzle, remove it with a needle or small pin . Do not substitute engine anti-freeze coolant for window washer solution. This may result in damage to the paint. WARNING Anti-freeze is poisonous and should be stored carefully in marked containers out of the reach of children. Maintenance and do-it-yourself 8-21 Chapter8.fm Page 22 Thursday, April 11, 2013 2:51 PM BATTERY VEHICLE BATTERY • Make certain the terminal connections are clean and securely tightened. • If the vehicle is not to be used for 30 days or longer, disconnect the "-'' negative battery terminal cable to prevent discharge. WARNING Do not operate the vehicle if the fluid in the battery is low. Low battery fluid can cause a higher load on the battery which can generate heat, reduce battery life and in some cases lead to an explosion. • Keep the battery surface clean and dry. Any corrosion should be washed off with a solution of baking soda and water. 8-22 Maintenance and do-it-yourself Chapter8.fm Page 23 Thursday, April 11, 2013 2:51 PM It is necessary to add fluid, add only distilled water to bring the level to the indicator in each filler opening. Don not overfill. WARNING • Do not expose the battery to flames or electrical sparks. Hydrogen gas generated by battery action is explosive. Do not allow battery fluid to contact your skin, eyes, fabrics, or painted surfaces. After touching a battery or battery cap, do not touch or rub your eyes. Thoroughly wash your hands. If the acid contacts your eyes, skin or clothing, immediately flush with water for at least 15 minutes and seek medical attention. • Keep the battery out of reach of children. Vehicles operated in high temperatures or under severe conditions require frequent checks of the battery fluid level. 1 Remove the cell plugs . 2 Add distilled water up to the UPPER LEVEL . If the side of the battery is not visible, the electrolyte level can be checked through each filler opening as illustrated. The indicator shows that the electrolyte level reaches to the upper level. Otherwise, the indicator means the electrolyte needs to be added. 3 Tighten cell plugs . CAUTION: Do not overfill battery cells. Excessive electrolyte may leak out of the battery during charging and cause paint damage. Jump starting If jump starting is necessary, see the “6. In case of emergency” section. If the engine does not start by jump starting, the battery may have to be replaced. Contact your NISSAN dealer. Check the fluid level in each cell. It should be between the UPPER LEVEL and LOWER LEVEL lines. Maintenance and do-it-yourself 8-23 Chapter8.fm Page 24 Thursday, April 11, 2013 2:51 PM FUSES WARNING Never use a fuse of higher amperage rating than that specified on the fuse box cover. ENGINE COMPARTMENT If the electrical equipment does not operate, check for a burnt fuse. 1 Be sure the ignition key and the headlight switch are "OFF''. 6 If a new fuse burns again, have the electrical system checked and repaired by your NISSAN Dealer. PASSENGER COMPARTMENT If any electrical equipment does not operate, check for a burnt fuse. 1 Be sure the ignition key and the headlight switch are "OFF''. 2 Open the fuse box lid. 2 Open the engine hood. 3 Remove the fuse with the fuse puller 3 Remove the fusible link cover. 4 If the fuse is burnt, replace it with a new fuse . 4 Remove the fuse with the fuse puller. 5 If the fuse is burnt, replace it with a new fuse. 8-24 Maintenance and do-it-yourself . 5 If a new fuse burns again , have the electrical system checked and repaired by your NISSAN Dealer. Chapter8.fm Page 25 Thursday, April 11, 2013 2:51 PM LIGHTS HEADLIGHTS CAUTION: Replace the halogen headlight bulb Use only genuine NISSAN or equivalent bulb as a replacement. Using an incorrect bulb can result in damage to the light. The halogen headlight is a semi-sealed beam type that uses a replaceable headlight bulb. A bulb can be replaced from inside the engine compartment without removing the headlight assembly. CAUTION: • High-pressure halogen gas is sealed inside the halogen bulb. The bulb may break if the glass envelope is scratched or the bulb is dropped. • DO NOT TOUCH THE BULB. • Use the same number and wattage as originally installed: • Aiming is usually not necessary after replacing the bulb. When aiming adjustment is necessary, contact your NISSAN Dealer. • Do not leave the bulb out of the headlight reflector for a long period of time as dust, moisture, and smoke may enter the headlight body and affect the performance of the headlight. Wattage 60/55 Maintenance and do-it-yourself 8-25 Chapter8.fm Page 26 Thursday, April 11, 2013 2:51 PM 1 Disconnect the battery negative (-) cable. 2 Disconnect the electrical connector from the rear end of the bulb and remove the rubber cap . 3 Push and turn the retaining pin loosen it. to 4 Remove the headlight bulb. Do not shake or rotate the bulb when removing it. 5 Install the new bulb in the reverse order of removal. Press the rubber cap firmly so the lip comes into contact with the headlight body. FRONT CLEARANCE LIGHTS AND FRONT TURN SIGNAL LIGHTS (if so equipped) Replacing the front clearance light bulb and front turn signal light bulb 1 Disconnect the battery negative cable. 2 Remove the clips attaching the radiator grille, then remove the radiator grille. 3 Remove the screws unit. on the headlight 4 Turn and remove the bulb socket. 8-26 Maintenance and do-it-yourself 5 Remove the front clearance light bulb or front turn signal light bulb . 6 Install the new bulb in the reverse order of removal. Chapter8.fm Page 27 Thursday, April 11, 2013 2:51 PM OTHER LIGHTS Item Wattage (W) Front turn signal light 21 Front clearance light 5 Side turn signal light 5 Front fog light* 55 Rear combination light Turn signal 21 Stop / tail 21 / 5 Reverse 18 Number plate light 5 Interior light 10 Personal light 8 *: if so equipped Maintenance and do-it-yourself 8-27 Chapter8.fm Page 28 Thursday, April 11, 2013 2:51 PM LIGHT LOCATION 1 Headlight Replacement procedures 2 Clearance/turn signal light All lights are either types A, B, C or D. When replacing a bulb, first remove the lens and/or cover. 3 Personal light 4 Interior light 5 Side turn signal light (if so equipped) 6 Rear combination light 7 License plate light 8-28 Maintenance and do-it-yourself Chapter8.fm Page 29 Thursday, April 11, 2013 2:51 PM Maintenance and do-it-yourself 8-29 Chapter8.fm Page 30 Thursday, April 11, 2013 2:51 PM WHEELS AND TYRES If you have a flat tyre, see "6. In case of emergency'' section. TYRE INFLATION PRESSURE Periodically check the tyre pressure (including spare). Tyre pressure should be checked when tyres are COLD. Tyres are considered COLD after the vehicle has been parked for three or more hours, or driven less than 1,6 km. COLD tyre pressures are shown on the tyre placard. CAUTION: Incorrect tyre pressure may adversely affect tyre life and vehicle handling. Insufficient pressure can lead to an overheating of the tyre and subsequent internal damage. At high speeds, this could result in tread separation and even bursting of the tyre. CAUTION: When changing or replacing tyres, be sure all four tyres are of the same type and construction. Your NISSAN Dealer may be able to help you with information about tyre type, size, speed rating and availability. Replacement tyres may have a lower speed rating than the factory equipped tyres, and may not match the potential maximum vehicle speed. Never exceed the maximum speed rating of the tyre. 8-30 Maintenance and do-it-yourself TYRE ROTATION TYRE WEAR AND DAMAGE NISSAN recommends that tyres be rotated: Except South Africa: 2WD - every 10 000 km. 4WD - every 5 000 km. For South Africa: 2WD - every 15 000 km. 4WD - every 7 500 km. See "Flat tyre'' in the "In case of emergency'' section for tyre replacing procedures. • After rotating the tyres, adjust the tyre pressure. Tyres should be periodically inspected for wear, cracking, bulging, or objects caught in the tread. If excessive wear, cracks, bulging, or deep cuts are found, the tyre should be replaced. • Retighten the wheel nuts after the vehicle has been driven for 1 000 km (600 miles) (also in cases of a flat tyre, etc.). WARNING Incorrect tyre selection, fitting, care or maintenance can affect vehicle safety with risk of accident and injury. If in doubt, consult your NISSAN Dealer or the tyre manufacturer. The original tyres have a built-in tread wear indicator . When the wear indicator is visible, the tyre should be replaced. The wear indictor locator locations are shown by the location marks . TYRE AGE Remember tyre age. Never use a tyre over six years old, regardless of whether it has been used or not. Chapter8.fm Page 31 Thursday, April 11, 2013 2:51 PM Tyres degrade with age as well as the use they are subjected to. Have your tyres checked and balanced frequently by a recognized tyre agent. Report all accidents where the tyre is knocked however minor. CHANGING TYRES AND WHEELS When replacing a tyre, use the same size, speed rating and load carrying capacity as originally equipped. Recommended types and sizes are shown in "TYRES AND WHEELS'' in the "9. Technical Information'' section. The use of tyres other than those recommended or the mixed use of tyres of different brands, construction (bias, bias-belted or radial), or tread patterns can adversely affect the ride, braking, handling, ground clearance, body-totyre clearance, speedometer calibration, headlight aim and bumper height. Some of these effects may lead to accidents and could result in serious personal injury. If the wheels are changed for any reason, always replace with wheels that have the same offset dimension. Wheels of a different offset could cause early tyre wear, possibly degraded vehicle handling characteristics and/or interference with the brake discs/ drums. Such interference can lead to decreased braking efficiency and/or early brake pad/shoe wear. 4-WHEEL DRIVE MODEL CAUTION: Always use tyres of the same size, brand, construction (bias, bias-belted or radial), and tread pattern on all four wheels. Failure to do so may result in a circumference difference between tyres on the front and rear axles that will cause excessive tyre wear and may damage the transmission, transfer case and differential gears. ONLY use spare tyres specified for each 4-wheel drive model. WHEEL BALANCE Unbalanced wheels may affect vehicle handling and tyre life. Even with regular use, wheels can get out of balance. Therefore, they should be balanced as required. CARE OF WHEELS • Wash the wheels when washing the vehicle to maintain their appearance. • Clean the inner side of the wheels when the wheel is changed or the underside of the vehicle is washed. • Do not use abrasive cleaners when washing the wheels. • Inspect wheel rims regularly for dents or corrosion. This may cause loss of pressure or damage the tyre bead. WARNING Do not install a deformed wheel or tyre even if it has been repaired. Such wheels or tyres could have structural damage and could fail without warning. CLUTCH HOUSING Checking water entry Whenever you drive in deep water or mud, check water entry in the clutch housing by removing the blind plug at the bottom of the transmission case. After checking, be sure to reinstall the plug. Maintenance and do-it-yourself 8-31 Chapter8.fm Page 32 Thursday, April 11, 2013 2:51 PM 8-32 Maintenance and do-it-yourself Chapter9TOC.fm Page 0 Thursday, April 11, 2013 2:53 PM 9 Technical information Recommended fuel/lubricants and capacities ................. 9-1 Recommended fuel ......................................................... 9-3 Recommended SAE viscosity number........................ 9-3 Recommended air conditioner system refrigerant and lubricant ................................................. 9-4 Air conditioner specification label ................................ 9-4 Engine ........................................................................................ 9-5 Wheels and Tyres.................................................................... 9-6 Dimensions ............................................................................... 9-7 When travelling or registering in another country ............ 9-8 Vehicle identification ............................................................... 9-8 Vehicle identification plate ............................................. 9-8 Vehicle identification number (Chassis number) ...... 9-9 Engine serial number....................................................... 9-9 Tyre placard ............................................................................9-10 NATS immobilizer radio apporval number........................9-10 Remote control radio approval number ............................9-10 Security Information ..............................................................9-13 Chapter9TOC.fm Page 1 Thursday, April 11, 2013 2:53 PM Chapter9.fm Page 1 Thursday, April 11, 2013 2:53 PM CAPACITIES AND RECOMMENDED FUEL/LUBRICANTS The following are approximate capacities. The “actual” refill capacities may be a little different. When refilling, follow the procedure instructed in the "Do-it-yourself operations'' section to Nissan recommended Spec *2: Contact a Nissan dealership for more information regarding suitable fluid, including recommended brands of DEXTRON™III. See “Fuel recommendations” *3: Never use CG-4 grade oil. determine the proper refill capacity. Model Fuel Diesel engine oil 2wd YD25 4wd Gasoline engine oil Manual gear oil transmission KA20 & KA24 2wd KA24 4wd KA24 2wd Differential carrier gear oil (Without limited slip differential) Front Diff gear oil Power steering fluid (with oil filter) (without oil filter) 3.6 3.3 4.2 3.9 (with oil filter) (without oil filter) (with oil filter) (without oil filter) 2.0 Except for Middle East For Middle East Transfer fluid Rear Diff gear oil 4.3 4.0 1.3 (Front) 1.3 (Rear) Differential carrier gear oil (With limited slip differential) Rear Diff gear oil Capacity (Approximate) in liters 60 - Short Wheel Base 75 - Long Wheel Base 75 - Double Cab 5.6 (with oil filter) 5.3 (without oil filter) KA20, KA24 & YD25 KA24 & YD25 KA24 & YD25 Models with Power Steering YD Type engine: Genuine NISSAN engine oil*1 API CF-4*1,*3 JASO DH-1*1 ACEA B1, B3, B4 or B5*1 Genuine NISSAN engine oil*1 API SE; SF; SG; SH; SJ; SL or SM*1 ILSAC grade GF-1; GF-2; GF-3; gf-4 or SG+*1 Genuine NISSAN Manual Transmission Fluid (MTF) HQ Multi 75W-85. Front: Except 4WD models for Middle East: Genuine NISSAN Differential Oil Hypoid Super GL-5 80W-90 or API GL-5, Viscosity SAE 80W-90. 4WD models for Middle East: API GL-5, Viscosity SAE 140 Rear: API GL-5*1 Genuine NISSAN Differential Oil Hypoid LSD GL-5 80W-90 or equivalent API GL-5 LSD oil, Viscosity SAE 140 or equivalent*1 Genuine NISSAN Matic D ATF (Part no KLE22-00004, 4Lt can; KLE22-00002;20Lt can) or equivalent*2 or API GL-4*1 Viscosity SAE 75W-90 2wd 1.5 Castrol Multitrax GMTM; Caltex EP Plus 460TM 4wd 1.45 Castrol Multitrax GM; Caltex EP Plus 460 1.3 API GL-5*1 4wd *1: For further detail, see SAE viscosity number charts in the Owners manual. CG-4 or higher spec oil can be used on condition that the container has the notation “JASO DH-1” *4: Use Nissan Genuine Long Life Coolant, Part no KQ10020001, in order to avoid possible aluminium corrosion within the engine cooling system caused by the use of non genuine engine coolant. Note that any repairs for the incidents within the cooling system while using non genuine engine coolant may not be covered by the warranty, even if such incidents occurred during the warranty period. Refill to the proper oil level according to “Do it TM yourself” Owners manual Type DEXTRON III or equivalent*2 section Table continue on next page. Technical information 9-1 Chapter9.fm Page 2 Thursday, April 11, 2013 2:53 PM Model Cooling System KA20 KA24 YD25 Brake and clutch fluid - Propeller shaft grease Multi purpose grease Air conditioning system refrigerant Air conditioning system lubricants - Capacity (Approximate) in liters 2wd 6.9 2wd & 4wd 6.9 2wd & 4wd 8.6 Refill to the proper oil level according to “Do it yourself” Owners manual section - Nissan recommended Spec Use Nissan LLC (Part no KQ10020001)*4 30%-LLC; 70%-water DOT 3!nq!CNS!3!!' Cn!mns!l hw!aq` j d!ekt hcr ( NLGI No 2 (Lithium soap base) NLGI No 2 (Lithium soap base) - - - HFC-134a (R-134a) - - - NISSAN A/C System Oil Type S or exact equivalent 9-2 Technical information Chapter9.fm Page 3 Thursday, April 11, 2013 2:53 PM FUEL RECOMMENDATION RECOMMENDED SAE VISCOSITY NUMBER Gasoline engine: Model with three-way catalyst: Unleaded gasoline of above 91 octane (RON). CAUTION: Do not use a leaded gasoline. Using a leaded gasoline will damage the threeway catalyst. Model without three-way catalyst: Use unleaded or leaded gasoline of above 88 octane (RON). Use unleaded fuel if instructed on the Fuel filler lid. Diesel engine: • YD25DDTi engine models Diesel fuel of above 50 cetane must be used. If fuel other than the specified fuel is used, white smoke could be emitted. For cold areas: For cold and warm areas: 5W-30 is preferable. 5W-20 is not recommended. 10W-30 is preferable for temperatures above -20ºC (-4ºF). For hot and warm areas: 5W-30 will positively improve fuel economy. 20W-40 and 20W-50 are suitable. For hot areas: ambient 20W-40 and 20W-50 are suitable. Technical information 9-3 Chapter9.fm Page 4 Thursday, April 11, 2013 2:53 PM RECOMMENDED AIR CONDITIONING SYSTEM REFRIGERANT AND LUBRICANT (If so equipped) VEHICLE IDENTIFICATION The air conditioning system in this NISSAN vehicle must be charged with the refrigerant HFC-134a (R-134a) and the lubricant, NISSAN A/C System Oil Type S or the exact equivalents. Use of any other refrigerants or lubricants will cause severe damage and you will need to replace your vehicle's entire air conditioning system. The release of refrigerant into the atmosphere is not recommended. The new refrigerant HFC-134a (R-134a) in your NISSAN vehicle will not harm the earth's ozone layer. However, it may contribute in a small part to global warming. NISSAN recommends that the refrigerant be recovered and recycled. Contact your NISSAN Dealer when servicing your air conditioning system. Rear differential For cold and warm areas: 90 or 80W-90 is preferable. For hot areas: 90 is suitable for ambient temperatures below 40ºC (104ºF). For extremely hot areas and the Middle East: 140 is preferable. 9-4 Technical information AIR CONDITIONER SPECIFICATION LABEL The air conditioner specification label affixed as shown. is Chapter9.fm Page 5 Thursday, April 11, 2013 2:53 PM ENGINE MODEL YD25DDTi KA20DE KA24DE Type Diesel, 4-cycle Gasoline, 4-cycle Gasoline, 4-cycle 4-cylinder, in-line 4-cylinder, in-line 4-cylinder, in-line 86 X 86 (3.39 x 3.39) 89 X 96 (3.50 x 3.78) 1,998 (121.88) 2,389 (145.78) 1-3-4-2 1-3-4-2 700 650 20 15 1.0 to 1.1 (0.039 to 0.043) 1.0 to 1.1 (0.039 to 0.043) BKR5E-II BKR5E-II Timing chain Timing chain Cylinder arrangement Bore X stroke mm (in) 89 X 100 (3.504 x 3.94) Displacement cm3(cu in) 2,488 (151.82) Firing order 1-3-4-2 Idling speed Ignition (BTDC) rpm 750 timing Spark plug gap Spark plugs Camshaft operation at idle mm Standard Chain drive Technical information 9-5 Chapter9.fm Page 6 Thursday, November 9, 2017 12:59 PM WHEELS AND TYRES Except for South Africa: 2wd 4wd S/Cab S/Cab D/Cab D/Cab S/Cab D/Cab D/Cab D/Cab STD STD STD GL STD STD STD GL GL KA24 YD25 YD25 YD25 YD25 KA24 YD25 KA24 YD25 X X X X X (*) MODEL Tyre Wheel 195R 14-8/8 14 inch Steel X 195 R15 5.5JJ-15 Steel X 215 R15 6JJ-15 Steel X 245/70 R16 7JJ-16 Alu 245/70 R16 7JJ-16 Steel X (**) D/Cab X (**) X (**) Opt - (*) = With ABS Opt - (**) = With Steel wheel For South Africa: 2wd MODEL Tyre Wheel 195R15 5.5JJ-15 245/70R16 7JJ-16 215R15 6JJ-15 Opt - (*) = With ABS Opt - (**) = With Alloy wheel 4wd S/Cab S/Cab S/Cab S/Cab S/Cab S/Cab S/Cab S/Cab D/Cab D/Cab S/Cab S/Cab D/Cab STD STD OPT SE STD STD OPT SE STD STD STD STD STD SWB LWB LWB LWB LWB LWB LWB LWB LWB LWB LWB LWB LWB KA20 KA20 KA20 KA20 KA24 YD25 YD25 YD25 KA24 YD25 KA24 YD25 KA24 X X X X X X (*) X Opt - 3 spoke steering wheel; 15” wheels, Diff lock and Tubular RR Bumper 9-6 Technical information X (*) X X (**) X Chapter9.fm Page 7 Thursday, April 11, 2013 2:53 PM DIMENSIONS Unit: mm (in) Vehicle type 2-wheel drive model Item Wheelbase Short Long Long Cab Single cab or bed type Single cab Double cab Long Single or Double cab Hi-Rider Single Cab Double Cab Overall length mm (in) 4600 (181.1) 4900 (181.1) 4960 (195.3) 4660 (183.5)*1 4960 (183.5)*1 5175 (203.7)*2 4900 (192.9) 5085 (200.1)*1 5085 (200.1)*1 Overall width mm (in) 1690 (66.5) 1690 (66.5) 1690 (66.5) 1825 (71.9) 1825 (71.9) 1825 (71.9) Overall height mm (in) 1620 (63.8) 1615 (63.6) 1645 (64.8) 1700 (66.9)*2 1790 (70.5)*4 1670 (65.7)*3 1790 (70.5) Overall height of vehicle can change due to local size tyres Wheelbase mm (in) 2650 (104.3) 2950 (104.3) 2950 (104.3) 2950 (104.3) 2950 (104.3) 2950 (104.3) Track 1395 (54.9) 1415 (55.7)*4 1395 (54.9) 1415 (55.7) 1530 (60.2) 1530 (60.2) 1530 (60.2) 1390 (54.7) 1410 (55.5)*4 1390 (54.7) 1410 (55.5) 1505 (59.3) 1505 (59.3) 1505 (59.3) 185 (7.3) 210 (8.3)*4 185 (7.3) 210 (8.3)*3 210 (8.3) 220 (8.7) 205 (8.1) 220 (8.7) 220 (8.7) Front: mm (in) Rear: mm (in) Ground clearance mm (in) *1 *2 *3 *4 4-wheel drive model RR bumper equipped models Single cab Hi Rider models 15” wheel models Double cab Hi Rider models Technical information 9-7 Chapter9.fm Page 8 Thursday, April 11, 2013 2:53 PM WHEN TRAVELLING OR REGISTERED IN ANOTHER COUNTRY VEHICLE IDENTIFICATION When planning to travel in another country, you should first find out if the fuel available is suitable for your vehicle's engine. Using fuel with too low an octane/cetane rating may cause engine damage. Therefore, avoid taking your vehicle to areas where appropriate fuel is not available. When transferring the registration of your vehicle to another country, state, province or district, check with the appropriate authorities that the vehicle complies with the requirements and it may not be possible to adapt the vehicle. In some cases, a vehicle cannot meet the legal requirements and in others it may be necessary to modify the vehicle to meet local laws and regulations. The laws and regulations for motor vehicle emission control and safety standards vary according to the country, state, province or district; therefore, vehicle specifications may differ. When any vehicle is to be taken into another country, state, province or district and registered, its modifications, transportation, and registration are the responsibility of the user. NISSAN is not responsible for any inconvenience that may result. 9-8 Technical information VEHICLE IDENTIFICATION PLATE 1 Vehicle type and chassis number (VIN The vehicle identification plate shown. 2 Gross vehicle mass is affixed as For South Africa only: The vehicle identification number (VIN number) is also displayed on the inside of the front- and rear windows of the vehicle. This is a Legal Requirement. Please do not tamper with the stickers. number) 3 Gross combination mass (vehicle full loaded, with trailer) 4 Maximum permissible weight on front axle. 5 Maximum permissible weight on rear axle. 6 Vehicle type 7 Model variation code 8 Bar code 9 Body & Trim colour codes Chapter9.fm Page 9 Thursday, April 11, 2013 2:53 PM YD25DDTi engine VEHICLE IDENTIFICATION NUMBER (VIN) ENGINE SERIAL NUMBER The vehicle identification number (Chassis number/VIN number) is stamped on the frame as shown. The engine serial number is stamped on the engine as shown. KA20DE/KA24DE engine Technical information 9-9 Chapter9.fm Page 10 Thursday, April 11, 2013 2:53 PM TYRE PLACARD NATS IMMOBILIZER RADIO APPROVAL NUMBER The cold tyre pressure is shown on the tyre placard . Remote keyless entry system. Your vehicle is equipped with one of the immobilizer systems shown above. See also NATS control unit additional approval numbers 9-10 Technical information REMOTE CONTROL RADIO APPROVAL NUMBER (for South Africa) Chapter9.fm Page 11 Thursday, April 11, 2013 2:53 PM REMOTE CONTROL RADIO APPROVAL NUMBER (for Nigeria) REMOTE CONTROL RADIO APPROVAL NUMBER KEYLESS ENTRY SYSTEM MODEL No. TWB1U761, TWD1G703 Connection and use of this communications Equipment is permitted by the Nigerian Communications Commission Remote keyless entry system. Technical information 9-11 Chapter9.fm Page 12 Thursday, April 11, 2013 2:53 PM 9-12 Technical information Chapter9.fm Page 13 Thursday, April 11, 2013 2:53 PM SECURITY INFORMATION As the Owner of this vehicle, a number of important codes have been supplied to you that you may require in case your radio needs to be repaired OR in case you need to duplicate a NATS key. SECURITY INFORMATION Radio security code (if so equipped) Please fill in the allocated areas for radio security code, key code and NATS PIN code* or attach the sticker(s) if available. For key code and NATS PIN code, see "Keys'' in the "2. Pre-driving checks and adjustments'' section. Remove the page from this manual and keep it in a safe place, not in the vehicle. Key Code When selling your vehicle, we kindly request you to hand over this page to the buyer. Remove the page from the manual and keep it in a safe place, not in the vehicle. * If so equipped for models with NATS When selling your vehicle, we kindly request you to hand over this page to the buyer. NATS - Nissan Anti Theft System * If so equipped for models with NATS Technical information 9-13 Chapter9.fm Page 14 Thursday, April 11, 2013 2:53 PM 9-14 Technical information Gas station information.fm Page 1 Thursday, April 11, 2013 2:55 PM GAS STATION INFORMATION RECOMMENDED ENGINE OIL QUICK REFERENCE RECOMMENDED FUEL Gasoline engine • Gasoline engine: Genuine NISSAN engine oil Model with three-way catalyst: API grade SE, SF, SG, SH, SJ, SL or SM Unleaded gasoline of above 91 octane (RON). ILSAC grade GF-1, GF-2, GF-3, GF-4 or SG+ CAUTION: Do not use a leaded gasoline. Using a leaded gasoline will damage the threeway catalyst. Diesel engine Model without three-way catalyst: Genuine NISSAN engine oil Use unleaded or leaded gasoline of above 88 octane (RON). API CF-4 Use unleaded fuel if instructed on the Fuel filler lid. ACEA B1, B3, B4 or B5 JASO DH-1 YD25DDTi engine models For further details, see “RECOMMENDED SAE VISCOSITY NUMBER” in the “9. Technical information” section. Diesel fuel of above 50 cetane must be used. TYRE COLD PRESSURE If fuel other than the specified fuel is used, white smoke could be emitted. See the tyre placard affixed to the driver’s side center pillar. Diesel engine: • YD with common rail: In case of emergency.... 6-1 (Flat tyre, engine will not start, overheating, towing) • How to start the engine.... 5-1 • How to read the meters and gauges.... 2-1 • Technical information.... 9-1 Gas station information.fm Page 2 Thursday, April 11, 2013 2:55 PM INDEX.fm Page 1 Tuesday, September 23, 2014 11:46 AM 10 Index A Adjustable head restraints .............................................1-2 Air bag warning label (if so equipped)..................... 1-18 Air bag warning light (if so equipped)...................... 1-18 Air cleaner filter ............................................................. 8-18 Air conditioner Air conditioner specification label .........................9-4 Heater and air conditioner.......................................4-2 Heater and manual air conditioner ........................4-2 Recommended air conditioner system refrigerant and lubricant...........................................9-4 Servicing air conditioner..........................................4-5 Antenna..............................................................................4-6 Anti-freeze ...................................................................... 5-22 Anti-lock Brake System(if so equipped).................. 5-19 Ashtrays .......................................................................... 2-18 Audio operation precautions.........................................4-6 Audio system (if so equipped)......................................4-6 Auto-lock free running hubs (if so equipped) ........ 5-12 B Battery ..................................................................5-22, 8-22 Battery replacement .................................................3-5 Vehicle battery ........................................................ 8-22 Before starting the engine .............................................5-1 Bleeding the fuel system............................................. 8-14 Blocking the wheels........................................................6-2 Brake ............................................................................... 8-16 Anti-lock Brake System (if so equipped).......... 5-20 Brake and clutch fluid ........................................... 8-17 Brake booster.......................................................... 8-16 Brake precautions.................................................. 5-18 Brake system........................................................... 5-18 Checking brake pedal ........................................... 8-16 Checking parking brake........................................ 8-16 Parking brake .......................................................... 3-12 C Car phone and CB radio............................................. 4-18 Care of wheels .............................................................. 8-31 Care when driving............................................................5-4 CD-player/LW-MW-FM radio type..............................4-7 Changing Changing engine coolant .......................................8-8 Changing engine oil .............................................. 8-10 Changing engine oil filter..................................... 8-12 Changing tyres and wheels................................. 8-31 Checking Checking brake pedal .......................................... 8-16 Checking bulbs .........................................................2-9 Checking engine coolant level ..............................8-7 Checking engine oil level........................................8-9 Checking parking brake ....................................... 8-16 Child restraints .................................................................1-7 Child safety rear door lock.............................................3-3 Chrome parts....................................................................7-1 Cleaning exterior ..............................................................7-1 Cleaning interior...............................................................7-2 Clock ..................................................................................2-8 Closing the hood .............................................................3-6 Clutch housing .............................................................. 8-31 Cold weather driving.................................................... 5-22 Coolant Changing engine coolant .......................................8-8 Checking engine coolant level ..............................8-7 Engine coolant ....................................................... 5-22 Engine coolant Temperature gauge .....................2-7 Corrosion protection........................................... 5-22, 7-2 Cup holder (if so equipped) ....................................... 2-19 Cyclone air cleaner....................................................... 8-18 D Gasoline engine with Manual Transmission ..............6-6 Diesel engine without throttle control knob...............5-9 Dimensions........................................................................9-7 Door locks .........................................................................3-2 Draining water ............................................................... 8-13 Drive belts ...................................................................... 8-15 Driver air bag system ................................................... 1-15 Driver and front passenger air bag system............. 1-12 Driving 4WD on-road and off-road driving precautions ................................................................5-3 Care when driving ....................................................5-4 Cold weather driving............................................. 5-22 Driving in dusty conditions .....................................4-5 Driving at the upland................................................5-4 Driving in wet conditions.........................................5-4 Driving in icy conditions ..........................................5-4 Driving safety precautions ................................... 5-17 Driving vehicle ...........................................................5-9 Driving with Manual Transmission.........................5-9 Precautions when starting and driving ................5-2 E Engine ................................................................................9-5 Before starting the engine ......................................5-1 Changing engine coolant ........................................8-8 Changing engine oil .............................................. 8-10 Checking engine coolant level...............................8-7 Checking engine oil level ........................................8-9 Gasoline engine with Manual Transmission........6-6 Diesel engine without throttle control knob ........5-9 Driving at the upland ................................................5-4 Engine cold start period ..........................................5-4 Engine compartment check locations..................8-4 INDEX.fm Page 2 Tuesday, September 23, 2014 11:46 AM Engine coolant ........................................................ 5-22 Engine coolant temperature gauge...................... 2-7 Engine cooling system ............................................ 8-7 Engine oil.................................................................... 8-9 Engine serial number............................................... 9-9 Fuel filter................................................................... 8-13 Gasoline engine ...................................................... 5-8 Starting engine.......................................................... 5-8 Environmental factors the rate of corrosion ........................................................................... 7-2 Exhaust gas ...................................................................... 5-2 Explanation of general maintenance items................ 8-1 F 4WD on-road and off-road driving precautions....................................................................... 5-3 Facts about oil and oil consumption......................... 8-10 Fitment of canopy ........................................................... 5-3 Flat tyre.............................................................................. 6-1 Fluid Brake and clutch fluid............................................ 8-17 Power steering fluid ............................................... 8-18 Window washer fluid .............................................8-21 FM-AM radio with Compact Disc changer .............4-14 Fog light switch (if so equipped)...............................2-15 Four-Wheel Drive..........................................................5-11 Freeing trapped vehicle ................................................. 6-9 Fuel Bleeding the fuel system....................................... 8-14 Fuel filler lid ................................................................ 3-7 Fuel filter ................................................................... 8-13 Fuel gauge ................................................................. 2-7 Recommended fuel .................................................. 9-3 Recommended fuel/lubricants and capacities ................................................................... 9-1 Fuses ............................................................................... 8-24 G K Gasoline engine ...............................................................5-8 Gasoline engine with Manual Transmission...............6-6 Gauge Engine coolant temperature gauge .......................2-7 Fuel gauge...................................................................2-7 Meters and gauges....................................................2-3 General maintenance ......................................................8-1 Glass..........................................................................7-1, 7-2 Glove box........................................................................ 2-19 Key Key positions ..............................................................5-8 Keys ..............................................................................3-1 Locking with key ........................................................3-2 H Hazard indicator flasher switch ................................. 2-15 Headed downhill ........................................................... 5-21 Headed uphill................................................................. 5-21 Headed uphill or downhill, no curb ........................... 5-21 Headlight Headlight and turn signal switch ......................... 2-14 Headlight switch...................................................... 2-14 Headlights................................................................. 8-25 Heater and air conditioner .............................................4-2 Heater and manual air conditioner...............................4-2 Hood ...................................................................................3-6 I If your vehicle overheats .................................................6-6 Ignition switch...................................................................5-7 Indicator lights ............................................................... 2-11 Inside rearview mirror ................................................... 3-11 Installation of child restraint system.............................1-9 Installing the spare tyre...................................................6-5 Instrument panel...............................................................2-1 Interior lights................................................................... 2-19 J Jump starting.....................................................................6-5 10-2 L Light Air bag warning light............................................. 1-18 Front clearance & Front turn signal lights ........ 8-26 Headlight and turn signal switch........................ 2-14 Headlight switch .................................................... 2-14 Headlights ............................................................... 8-25 Indicator lights ........................................................ 2-11 Interior lights ........................................................... 2-19 Light locations ........................................................ 8-28 Lights........................................................................ 8-25 Other lights ............................................................. 8-27 Security indicator light.......................................... 2-12 Warning lights ...........................................................2-9 Warning/indicator lights and audible reminders....................................................................2-9 Loading the luggage .......................................................5-4 Lock Anti-lock Brake System (if so equipped) ......... 5-19 Child safety rear door lock .....................................3-3 Locking doors............................................................3-2 Locking with inside lock knob................................3-2 Locking with key .......................................................3-2 Locking with power door lock switch (if so equipped) ...................................................................3-3 Remote control door lock system (if so equipped) ...................................................................3-4 Unlocking doors........................................................3-5 INDEX.fm Page 3 Tuesday, September 23, 2014 11:46 AM M P Maintenance Explanation of general maintenance items..........8-1 General maintenance...............................................8-1 Maintenance precautions........................................8-2 Maintenance requirements .....................................8-1 Scheduled maintenance..........................................8-1 Seat belt maintenance.............................................1-4 Manual-lock free running hubs .................................. 5-15 Manual Transmission.......................................................5-9 Manual windows ........................................................... 2-16 Meters and gauges .........................................................2-3 Mirror Inside rearview mirror............................................ 3-11 Mirrors ...................................................................... 3-10 Outside rearview mirrors...................................... 3-10 Vanity mirror (if so equipped) .............................. 3-12 Most common factors contributing to vehicle corrosion............................................................................7-2 Parking Checking parking brake....................................... 8-16 Parking brake ......................................................... 3-12 Passenger compartment............................................. 8-24 Plastic parts ......................................................................7-1 Power Power steering fluid.............................................. 8-18 Power steering system......................................... 5-18 Power windows (if so equipped)....................... 2-16 Power point .................................................................... 2-18 Pre-tensioner seat belt system (if so equipped) ... 1-19 Precautions 4WD on-road and off-road driving precautions ................................................................5-3 Audio operation precautions .................................4-6 Brake precautions................................................. 5-18 Driving safety precautions................................... 5-17 Maintenance precautions .......................................8-2 Operating precautions ............................................5-4 Precautions on child restraints usage .................1-7 Precautions on seat belt usage ............................1-3 Precautions when starting and driving................5-2 Preparing the tools and spare tyre.......................6-2 Protect the environment .............................................. 8-13 Push starting.....................................................................6-6 N NATS ..................................................................................3-2 NATS immobilizer radio apporval number............... 9-10 O Oil Changing engine oil............................................... 8-10 Changing engine oil filter...................................... 8-12 Checking engine oil level.........................................8-9 Engine oil.....................................................................8-9 Opening the hood ...........................................................3-7 Operating precautions....................................................5-4 Other lights .................................................................... 8-27 Outside rearview mirrors............................................. 3-10 Overheat If your vehicle overheats ..........................................6-6 R Radio CD player/FM-AM radio type ................................4-7 Rear sliding window..................................................... 2-18 Recommended air conditioner system refrigerant and lubricant .................................................9-4 Recommended fuel .........................................................9-3 Recommended fuel/lubricants and capacities..........9-1 Recommended heat range ......................................... 8-16 Recommended SAE viscosity number .......................9-3 Recommended towing for 2-wheel drive models................................................................................6-8 Recommended towing for 4-wheel drive models................................................................................6-8 Remote control door lock system (if so equipped) 3-4 Remote control radio approval number ................... 9-10 Removing spots ...............................................................7-1 Removing the tyre............................................................6-3 Replacing spark plugs ................................................. 8-15 Running-in schedule .......................................................5-1 S 2-point type seat belts....................................................1-5 Safety Child safety rear door lock ....................................3-3 Driving safety precautions (4X4) ...................... 5-17 Scheduled maintenance ........................................8-1 Seat 2-point type seat belts ...........................................1-5 3-point type seat belts ...........................................1-4 Pre-tensioner seat belt systemm (if so equipped) ............................................................... 1-19 Precautions on seat belt usage............................1-3 Seat adjustment.......................................................1-1 Seat belt maintenance............................................1-4 Seat belts ..................................................................1-3 Seats ..........................................................................1-1 Tilting bench seat ....................................................1-2 Tilting front bucket seat (if so equipped) ...........1-1 Seat belt 2-point type seat belts ...........................................1-5 3-point type seat belts ...........................................1-4 Pre-tension seat belt system (if so equipped)..................................................... 1-19 Precautions on seat belt usage............................1-3 Seat belt maintenance............................................1-4 Seat belts ..................................................................1-3 Security indicator light................................................. 2-12 Security system (if so equipped) .............................. 2-12 Servicing air conditioner ................................................4-5 Speedometer and odometer.........................................2-6 Starting Before starting the engine .....................................5-1 Jump starting ............................................................6-5 10-3 INDEX.fm Page 4 Tuesday, September 23, 2014 11:46 AM Precautions when staring and driving................ 5-2 Push starting ............................................................ 6-6 Starting engine ........................................................ 5-8 Steering Power steering fluid.............................................. 8-18 Power steering system ........................................5-18 Steering wheel.......................................................3-10 Tilting steering wheel (if so equipped).............3-10 Stopping the vehicle ...................................................... 6-1 Supplement restraint system (if so equipped) ....... 1-12 Switch Hazard indicator flasher switch ......................... 2-14 Headlight and turn signal switch.......................2-14 Headlight switch ................................................... 2-14 Ignition switch.......................................................... 5-8 Locking with power door lock switch (if so equipped) ................................................................. 3-3 Turn signal switch ................................................. 2-14 Windshield wiper and washer switch .............. 2-13 Wiper and washer switch ................................... 2-13 4 x 4 tyres of 4-wheel drive ................................. 5-18 Wheels and tyres ......................................................9-6 To protect your vehicle from corrosion .......................7-3 Towing Recommended towing for 2-wheel drive models .........................................................................6-8 Recommended towing for 4-wheel drive models .........................................................................6-8 Towing precautions...................................................6-7 Trailer towing ..............................................................5-4 Transfer case shifting procedures............................. 5-11 Transmission Gasoline engine with Manual Transmission........6-6 Driving with Manual Transmission .........................5-9 Turbocharger system (if so equipped) ........................5-3 Turn signal switch ......................................................... 2-14 U Unlocking doors ...............................................................3-5 T V 3-point type seat belts................................................... 1-4 Tachometer (if so equipped) ........................................ 2-6 Tailgate .............................................................................. 3-9 Tie down hooks (if so equipped)................................. 3-9 Tilting bench seat............................................................ 1-2 Tilting front bucket seat (if so equipped)................... 1-1 Tilting steering wheel (if so equipped).....................3-10 Tyre Changing tyre and wheels ................................... 8-31 Flat tyre ....................................................................... 6-1 Installing the spare tyre........................................... 6-5 Preparing the tools and spare tyre....................... 6-2 Removing the tyre .................................................... 6-3 Tyre age ....................................................................8-30 Tyre inflation pressure ...........................................8-30 Tyre placard ............................................................. 9-10 Tyre pressure............................................................. 5-6 Tyre rotation ............................................................. 8-30 Tyre wear and damage.......................................... 8-30 Vanity mirror (if so equipped) ..................................... 3-12 Vehicle battery ............................................................... 8-22 Vehicle identification Vehicle identification number ...................................9-9 Vehicle identification plate ........................................9-8 Vehicle security.............................................................. 5-22 Ventilators ..........................................................................4-1 10-4 W Warning Air bag warning label............................................. 1-18 Air bag warning light.............................................. 1-18 Warning lights ............................................................2-9 Warning/indicator lights and audible reminders.....................................................................2-9 Washing .............................................................................7-1 Waxing................................................................................7-1 Wheel balance............................................................... 8-31 Wheels and tyres .............................................................9-6 When travelling or registering in another country................................................................................9-8 Where to go for service..................................................8-1 Window washer fluid ................................................... 8-21 Windows......................................................................... 2-16 Windshield washer nozzle .......................................... 8-21 Windshield wiper and washer switch ...................... 2-13 Wiper Windshield wiper and washer switch .............. 2-13 Wiper and washer switch ................................... 2-13 Wiper blades ......................................................... 8-20