Nissan - 240 SX - Owners Manual - 2003 - 2003

FOREWORD READ FIRST—THEN DRIVE SAFELY Welcome to the growing family of new NISSAN owners. This vehicle is delivered to you with confidence. It was produced using the latest techniques and strict quality control. Before driving your vehicle please read this Owner’s Manual carefully. This will ensure familiarity with controls and maintenance requirements, assisting you in the safe operation of your vehicle. This manual was prepared to help you understand the operation and maintenance of your vehicle so that you may enjoy many miles (kilometers) of driving pleasure. Please read through this manual before operating your vehicle. A separate Warranty Information Booklet explains details about the warranties covering your vehicle. The “NISSAN Service and Maintenance Guide” explains details about maintaining and servicing your vehicle. Additionally, a separate Customer Care/Lemon Law Booklet (U.S. only) will explain how to resolve any concerns you may have with your vehicle, as well as clarify your rights under your state’s lemon law. Your NISSAN dealership knows your vehicle best. When you require any service or have any questions, they will be glad to assist you with the extensive resources available to them. WARNING IMPORTANT SAFETY INFORMATION REMINDERS FOR SAFETY! Follow these important driving rules to help ensure a safe and complete trip for you and your passengers! The inside pages of this manual contain a minimum of 50% recycled fibers, including 10% post-consumer fibers. MODIFICATION OF YOUR VEHICLE This vehicle should not be modified. Modification could affect its performance, safety or durability, and may even violate governmental regulations. In addition, damage or performance problems resulting from modifications may not be covered under NISSAN warranties. ● NEVER drive under the influence of alcohol or drugs. ● ALWAYS observe posted speed limits and never drive too fast for conditions. ● ALWAYS use your seat belts and appropriate child restraint systems. Preteen children should be seated in the rear seat. ● ALWAYS provide information about the proper use of vehicle safety features to all occupants of the vehicle. ● ALWAYS review this owner’s manual for important safety information. Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X The inside pages of this manual contain a minimum of 50% recycled fibers, including 10% post-consumer fibers. WHEN READING THE MANUAL CALIFORNIA PROPOSITION 65 WARNING This manual includes information for all options available on this model. Therefore, you may find some information that does not apply to your vehicle. WARNING All information, specifications and illustrations in this manual are those in effect at the time of printing. NISSAN reserves the right to change specifications or design without notice and without obligation. IMPORTANT INFORMATION ABOUT THIS MANUAL You will see various symbols in this manual. They are used in the following ways: WARNING This is used to indicate the presence of a hazard that could cause death or serious personal injury. To avoid or reduce the risk, the procedures must be followed precisely. APD1005 If you see this symbol, it means “Do not do this” or “Do not let this happen.” If you see a symbol similar to these in an illustration, it means the arrow points to the front of the vehicle. CAUTION This is used to indicate the presence of a hazard that could cause minor or moderate personal injury or damage to your vehicle. To avoid or reduce the risk, the procedures must be followed carefully. Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. In addition, certain fluids contained in vehicles and certain products of component wear contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Arrows in an illustration that are similar to these indicate movement or action. Arrows in an illustration that are similar to these call attention to an item in the illustration. © 2003 NISSAN NORTH AMERICA, INC. GARDENA, CALIFORNIA All rights reserved. No part of this Owner’s Manual may be reproduced or stored in a retrieval system, or transmitted in any form, or by any means, electronic, mechanical, photocopying, recording or otherwise, without the prior written permission of Nissan North America, Inc., Gardena, California. Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X WELCOME TO THE WORLD OF NISSAN NISSAN pioneered the use of electronics and computers in automobiles, and has led the industry in improving both performance and fuel efficiency through new engine designs and the use of synthetic materials to reduce vehicle weight. The company has also developed ways to build quality into its vehicles at each stage of the production process, both through extensive use of automation and — most importantly — through an awareness that people are the central element in quality control. WFW0014 Your new NISSAN is the result of our dedication to produce the finest in safe, reliable and economical transportation. Your vehicle is the product of a successful worldwide company that manufactures cars and trucks in over 17 countries and distributes them in 170 nations. NISSAN vehicles are designed and manufactured by Nissan Motor Co., Ltd. which was founded in Tokyo, Japan in 1933, and NISSAN affiliates worldwide, collectively growing to become the fifth largest automaker in the world. In addition to cars and trucks, NISSAN also makes forklift trucks, marine engines, boats and other diversified products. NISSAN has made a substantial and growing investment in North America. NISSAN’s commitment is over $6 billion dollars in capital investments in facilities across the continent. Some of the facilities include the Nissan Manufacturing facilities in Canton, Mississippi and in Smyrna, Tennessee, vehicle styling design at Nissan Design America, Inc. in San Diego, California, and engineering at Nissan Technical Center North America in Farmington Hills, Michigan. Additionally, NISSAN employs more than 21,000 people throughout the United States, Canada, and Mexico. An additional 60,000 people work for the 1,250 NISSAN and INFINITI dealers across North America. NISSAN is also a substantial contributor to the Canadian economy. Nissan Canada Inc., its suppliers and over 150 dealers employ approximately 4,500 people. These include company employees and the staffs of NISSAN dealers all across Canada. In addition, many Canadians work for companies that supply NISSAN and NISSAN dealers with materials and services ranging from the operation of port facilities and transportation services, to the supply of lubricants, parts and accessories. From the time the parts arrived from our suppliers until you took delivery of your new NISSAN, dozens of checks were made to ensure that only the best job was being done in producing and delivering your vehicle. NISSAN also takes great care to ensure that when you take your NISSAN to your dealer for maintenance, the service technician will perform his work according to the quality standards that have been established by NISSAN. Safety has also been built into your NISSAN. As you know, seat belts are an integral part of the safety systems that will help protect you and your passengers in the event of a sudden stop or an accident. We urge you to use the seat belts every time you drive the vehicle. The NISSAN story of growth and achievement reflects our major goal: to provide you, our customer, with a vehicle that is built with quality and craftsmanship — a product that we can be proud to build and you can be proud to own. Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X NISSAN CUSTOMER CARE PROGRAM NISSAN CARES . . . Both NISSAN and your NISSAN dealer are dedicated to serving all your automotive needs. Your satisfaction with your vehicle and your NISSAN dealer are our primary concerns. Your NISSAN dealer is always available to assist you with all your automobile sales and service needs. However, if there is something that your NISSAN dealer cannot assist you with or you would like to provide NISSAN directly with comments or questions, please contact the NISSAN Consumer Affairs Department using our toll-free number: For U.S. mainland and Alaska customers 1-800-NISSAN-1 (1-800-647-7261) 1-808-836-0888 (Oahu Number) 1-800-387-0122 – Your name, address, and telephone number – Vehicle identification number (attached to the top of the instrument panel on the driver’s side) – Date of purchase For Hawaii customers For Canadian customers The Consumer Affairs Department will ask for the following information: – Current odometer reading – Your NISSAN dealer’s name – Your comments or questions OR You can write to NISSAN with the information at: For U.S. mainland and Alaska customers Nissan North America, Inc. Consumer Affairs Department P.O. Box 191 Gardena, California 90248-0191 For Hawaii customers Nissan Motor Corporation in Hawaii 2880 Kilihau St. Honolulu, Hawaii 96819 For Canadian customers Nissan Canada Inc. 5290 Orbitor Drive Mississauga, Ontario L4W 4Z5 We appreciate your interest in NISSAN and thank you for buying a quality NISSAN vehicle. Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X Table of Contents Illustrated table of contents 0 Safety—Seats, seat belts and supplemental air bags 1 Instruments and controls 2 Pre-driving checks and adjustments 3 Display screen, heater, air conditioner and audio systems 4 Starting and driving 5 In case of emergency 6 Appearance and care 7 Maintenance and do-it-yourself 8 Technical and consumer information 9 Index 10 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X 0 Illustrated table of contents Airbags, seat belts and child restraints . . . . . . . . . . . . . . . 0-2 Exterior front . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0-3 Exterior rear. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0-4 Passenger compartment . . . . . . . . . . . . . . . . . . . . . . . . . . . 0-5 Instrument panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0-6 Engine compartment locations . . . . . . . . . . . . . . . . . . . . . . 0-8 Warning/indicator lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0-9 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X AIRBAGS, SEAT BELTS AND CHILD RESTRAINTS 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 3rd row bench center seat belt (P. 1-31) 3rd row bench seat belts (P. 1-31) Top tether strap anchor points (P. 1-53) 2nd row captain’s chair seat belts (P. 1-31) Front seat belts (P. 1-31) Supplemental curtain side-impact air bag (P. 1-15) Supplemental front impact air bags (P. 1-15) Seats (P. 1-2) Occupant classification sensor (weight sensor) (P.1-22) Seat belt pretensioners (P. 1-28) Top tether strap anchor for vehicles without 2nd or 3rd row seats (P. 1-53) Supplemental side impact air bag (if so equipped) (P. 1-15) LATCH (Lower Anchors and Tethers for CHildren) (P. 1-51) See the page number indicated in parentheses for operating details. LII0012 0-2 Illustrated table of contents Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X EXTERIOR FRONT 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. Engine hood (P. 3-14) Headlight and turn signal switch (P. 2-15) Replacing bulbs (P. 8-28) Windshield wiper and washer switch (P. 2-13) Windshield (P. 8-19) Power windows (P. 2-36) Door locks, keyfob, keys (P. 3-3, 3-9, 3-2) Mirrors (P. 3-23) Tire pressure (P. 9-11) Flat tire (P. 6-2) Tire chains (P. 8-36) Fog light switch (P. 2-19) Tie down/towing hooks (P. 6-12) See the page number indicated in parentheses for operating details. LII0013 Illustrated table of contents 0-3 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X EXTERIOR REAR 1. 2. 3. 4. 5. 6. 7. 8. Rear window defroster switch (P. 2-15) Vehicle loading (P. 9-12) Back door (P. 3-15) Back door release (P. 3-18) Replacing bulbs (P. 8-28) Fuel filler cap, fuel recommendation (P. 3-20, P. 9-3) Fuel filler lid (P. 3-20) Sliding doors (P. 3-5, P. 3-7) See the page number indicated in parentheses for operating details. LII0014 0-4 Illustrated table of contents Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X PASSENGER COMPARTMENT 1. DVD entertainment system (if so equipped) (P. 4-44) 2. Personal lights (P. 2-42) 3. Skyview roof (if so equipped) (P. 2-39) 4. Sunroof (if so equipped) (P. 2-39) 5. Map lights (P. 2-43) 6. Sun visors (P. 3-22) 7. HomeLinkT (P. 2-43) 8. Storage (P. 2-25) 9. Glove box (P. 2-28) 10. Seats (P. 1-2) 11. Cup holders (P. 2-32) See the page number indicated in parentheses for operating details. LII0018 Illustrated table of contents 0-5 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X INSTRUMENT PANEL 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. WIC0599 16. Driver side, center and passenger side ventilators (P. 4-17) Headlight and turn signal switch (P. 2-15) Steering wheel switch for audio control (if so equipped) (P. 4-41) Driver supplemental air bag/horn (P. 1-15, P. 2-20) Cruise control main/set switches (P. 5-12) Windshield wiper/washer switch and rear window wiper/washer switch (P. 2-13, 2-14) Meters and gauges (P. 2-3) Display screen/Navigation system* (P. 4-2, P. 4-8) Warning/indicator lights (P. 2-6) Front passenger supplemental air bag (P. 1-15) Glove box (P. 2-28) Climate controls (P. 4-17, 4-27) Hazard warning flasher switch (P. 2-20) Audio system controls (P. 4-30) Display screen/Navigation system* controls (P. 4-2, 4-8) Shift selector lever (P. 5-7) 0-6 Illustrated table of contents Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X 17. 18. 19. 20. 21. 22. Tilt steering wheel controls (P. 3-21) Rear sonar system off switch (if so equipped) (P. 2-22) Vehicle dynamic control (VDC) off switch (if so equipped) or Traction control system (TCS) off switch (if so equipped) (P. 2-22, P. 2-22) Lights on demand switch (P.2-41 ) Instrument brightness control (P. 2-18) Outside mirror controls (P. 3-24) *: Refer to the separate Navigation System Owner’s Manual (if so equipped). See the page number indicated in parentheses for operating details. Illustrated table of contents 0-7 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X ENGINE COMPARTMENT LOCATIONS 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. Power steering fluid reservoir (P. 8-13) Engine oil filler cap (P. 8-8) Brake fluid reservoir (P. 8-14) Air cleaner (P. 8-18) Battery (P. 8-15) Fuse/fusible link box (P. 8-23) Transmission dipstick (P. 8-11, P. 8-12) Engine oil dipstick (P. 8-8) Radiator cap (P. 8-7) Fuse block (P. 8-23) Windshield washer fluid reservoir (P. 8-14) 12. Coolant reservoir (P. 8-7) See the page number indicated in parentheses for operating details. LII0017 0-8 Illustrated table of contents Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X WARNING/INDICATOR LIGHTS Warning light or or Name Page Anti-lock brake warning light 2-6 Brake warning light 2-7 Warning light Name Page Low tire pressure warning light 2-8 Low windshield washer fluid warning light 2-9 Seat belt warning light and chime 2-9 Supplemental air bag warning light 2-9 Indicator light or Name Page Automatic transmission position indicator light 2-9 Front passenger air bag status light 2-8 Cruise main switch indicator light 2-9 2-10 2-10 Charge warning light 2-7 Door open warning light 2-7 Engine oil pressure warning light 2-7 Cruise set switch indicator light Low fuel warning light 2-8 High beam indicator light (blue) Illustrated table of contents 0-9 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X Indicator light Name Page Malfunction indicator lamp (MIL) 2-10 Overdrive off indicator light 2-10 Security indicator light (NVIS) 2-8 Slip indicator light 2-10 Traction control system off indicator light (if so equipped) 2-10 Turn signal/hazard indicator lights 2-11 Indicator light Name Vehicle dynamic control off indicator light (if so equipped) Page 2-11 0-10 Illustrated table of contents Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X 1 Safety—Seats, seat belts and supplemental air bags Seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2 Front manual seat adjustment (if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2 Front power seat adjustment (if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5 2nd row captain’s chair adjustment . . . . . . . . . . . . . . . 1-6 3rd row bench seat adjustment . . . . . . . . . . . . . . . . . . 1-8 Head restraint adjustment . . . . . . . . . . . . . . . . . . . . . . 1-10 Armrests . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-11 Flexible seating. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-11 Supplemental restraint system . . . . . . . . . . . . . . . . . . . . . 1-15 Precautions on supplemental restraint system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-15 Supplemental air bag warning labels . . . . . . . . . . . . . 1-29 Supplemental air bag warning light . . . . . . . . . . . . . . 1-30 Seat belts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-31 Precautions on seat belt usage. . . . . . . . . . . . . . . . . . 1-31 Child safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-33 Pregnant women . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-34 Injured persons. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-34 Three-point type seat belt with retractor . . . . . . . . . . 1-35 Seat belt extenders . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-40 Seat belt maintenance . . . . . . . . . . . . . . . . . . . . . . . . . 1-40 Child restraints . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-40 Precautions on child restraints . . . . . . . . . . . . . . . . . . 1-40 Installation on 2nd row captain’s chairs . . . . . . . . . . 1-42 Installation on 3rd row bench seat . . . . . . . . . . . . . . . 1-46 LATCH (Lower Anchors and Tethers for CHildren) system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-51 Top tether strap child restraint . . . . . . . . . . . . . . . . . . 1-53 Installation on front passenger seat . . . . . . . . . . . . . . 1-55 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X SEATS FRONT MANUAL SEAT ADJUSTMENT (if so equipped) WARNING ● Do not adjust the driver’s seat while driving so full attention may be given to vehicle operation. The seat may move suddenly and could cause loss of control of the vehicle. ● After adjustment, gently rock in the seat to make sure it is securely locked. ARS1152 WARNING ● Do not ride in a moving vehicle when the seatback is reclined. This can be dangerous. The shoulder belt will not be against your body. In an accident, you could be thrown into it and receive neck or other serious injuries. You could also slide under the lap belt and receive serious internal injuries. ● For the most effective protection when the vehicle is in motion, the seat should be upright. Always sit well back in the seat and adjust the seat properly. See “Precautions on Seat Belt Usage” later in this section. 1-2 Safety—Seats, seat belts and supplemental air bags Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X WARNING After adjustment, gently rock in the seat to make sure it is securely locked. WRS0274 WRS0275 Forward and backward Reclining Pull the lever up and hold it while you slide the seat forward or backward to the desired position. Release the lever to lock the seat in position. To recline the seatback, pull the lever up and lean back. To bring the seatback forward, pull the lever up and lean your body forward. Release the lever to lock the seatback in position. The reclining feature allows adjustment of the seatback for occupants of different sizes to help obtain proper seat belt fit (see “Precautions on seat belt usage” later in this section). Also, the seatback can be reclined to allow occupants to rest when the vehicle is stopped. Safety—Seats, seat belts and supplemental air bags 1-3 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X WRS0131 Seat lifter (if so equipped for driver’s seat) Turn either dial to adjust the angle and height of the seat cushion to the desired position. LRS0278 Lumbar support (driver’s seat) The lumbar support feature provides lower back support to the driver. Move the lever up or down to adjust the seat lumbar area. 1-4 Safety—Seats, seat belts and supplemental air bags Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X ● Do not operate the power seat switch for a long period of time when the engine is off. This will discharge the battery. See “Automatic drive positioner (if so equipped)” in “Pre-driving checks and adjustments” for automatic drive positioner operation. Forward and backward Moving the switch forward or backward will slide the seat forward or backward to the desired position. Reclining WRS0276 FRONT POWER SEAT ADJUSTMENT (if so equipped) WARNING ● Do not adjust the driver’s seat while driving so full attention may be given to vehicle operation. The seat may move suddenly and could cause loss of control of the vehicle. ● Do not leave children unattended inside the vehicle. They could unknowingly activate switches or controls and become trapped in a window. Unattended children could become involved in serious accidents. Operating tips ● The power seat motor has an auto-reset overload protection circuit. If the motor stops during operation, wait 30 seconds, then reactivate the switch. Move the recline switch backward until the desired angle is obtained. To bring the seatback forward again, move the switch forward and move your body forward. The seatback will move forward. The reclining feature allows adjustment of the seatback for occupants of different sizes to help obtain proper seat belt fit (see “Precautions on seat belt usage” later in this section). Also, the seatback can be reclined to allow occupants to rest when the vehicle is stopped. Safety—Seats, seat belts and supplemental air bags 1-5 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X WRS0277 Seat lifter (if so equipped for driver’s seat) Push the front or rear end of the switch up or down to adjust the angle and height of the seat cushion. LRS0278 Lumbar support (driver’s seat) The lumbar support feature provides lower back support to the driver. Move the lever up or down to adjust the seat lumbar area. LRS0279 2ND ROW CAPTAIN’S CHAIR ADJUSTMENT Forward and backward 1 and hold it while you slides 2 Pull the lever ups the seat forward or backward to the desired position. Release the lever to lock the seat in position. 1-6 Safety—Seats, seat belts and supplemental air bags Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X ● Do not ride in a moving vehicle when the seatback is reclined. This can be dangerous. The shoulder belt will not be against your body. In an accident, you could be thrown into it and receive neck or other serious injuries. You could also slide under the lap belt and receive serious internal injuries. WRS0317 LRS0283 Reclining Folding To recline the seatback, pull up on the lever and lean back. To fold the seatback forward, for cargo hauling, lift up on the recline lever and fold the seatback over the seat base. The recline feature allows adjustment of the seat back for occupants of different sizes to help obtain proper seat belt fit (see “Precautions on seat belt usage” later in this section). Also, the seatback can be reclined to allow occupants to rest when the vehicle is stopped. WARNING ● After adjustment, gently rock in the seat to make sure it is securely locked. WARNING ● Never allow anyone to ride in the cargo area or on the rear seat when it is in the fold-down position. Use of these areas by passengers without proper restraints could result in serious injury in an accident or sudden stop. Safety—Seats, seat belts and supplemental air bags 1-7 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X ● It is extremely dangerous to ride in a cargo area inside a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. ● Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. Be sure everyone in your vehicle is in a seat and using a seat belt properly. LRS0282 Tip up for easy entry to the 3rd row The 2nd row captain’s chairs can be tipped forward for easy entry or exit from the 3rd row bench seat. To enter the 3rd row bench seat lift up on the lever located on the lower base of the 2nd row captain’s chair to tip the seat forward. To exit the 3rd row bench seat pull back on the lever on the lower base of the 2nd row captain’s chair and push the seat forward. LRS0320 3RD ROW BENCH SEAT ADJUSTMENT Reclining Lift up on the latch in the center of the seatback to adjust the back of the seat. Release the latch to lock the seatback into position. WARNING ● After adjustment, gently rock in the seat to make sure it is securely locked. 1-8 Safety—Seats, seat belts and supplemental air bags Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X ● Do not ride in a moving vehicle when the seatback is reclined. This can be dangerous. The shoulder belt will not be against your body. In an accident, you could be thrown into it and receive neck or other serious injuries. You could also slide under the lap belt and receive serious internal injuries. ● It is extremely dangerous to ride in a cargo area inside a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. ● Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. Be sure everyone in your vehicle is in a seat and using a seat belt properly. LRS0284 Folding To fold the seatback forward, for cargo hauling, lift up on the latch in the center of the seatback to fold the seatback over the seat base. WARNING ● Never allow anyone to ride in the cargo area or on the rear seat when it is in the fold-down position. Use of these areas by passengers without proper restraints could result in serious injury in an accident or sudden stop. Safety—Seats, seat belts and supplemental air bags 1-9 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X WARNING Head restraints should be adjusted properly as they may provide significant protection against injury in an accident. Do not remove them. Check the adjustment after someone else uses the seat. LRS0286 HEAD RESTRAINT ADJUSTMENT To raise the head restraint, pull it up. To lower, push and hold the lock knob and push the head restraint down. WRS0134 Adjust the head restraint so the center is level with the center of your ears. The 2nd row captain’s chairs and the 3rd row bench seat head restraints are removable for stowage. The front seat head restraints are not removable. 1-10 Safety—Seats, seat belts and supplemental air bags Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X WRS0287 WRS0288 WRS0289 s ARMRESTS FLEXIBLE SEATING To use the armrests on any seat, pull them down to the resting position. Folding the 2nd row captain’s chair 3 1 s To fold the 2nd row captain’s chairs to the floor for maximum cargo hauling, remove the head restraints. Remove the head restraints by lifting up, then push and hold the release knob and place them in the storage bag. Make sure to secure the storage bag, see “Head restraint storage” in the “Instrument and controls” section of this Owner’s Manual. 2 s Lift up on the recline lever to fold the seatback forward on the seat base. Push down on the small knob on the back of the seat to release the base of the seat. Safety—Seats, seat belts and supplemental air bags 1-11 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X 5 s Reverse this process to return the 2nd row captain’s chairs to a seating position. Make sure to properly install the head restraints and to push the seats down into the floor until they latch into place. WARNING ● When returning the seatbacks to the upright position, be certain they are completely secured in the latched position. If they are not completely secured, passengers may be injured in an accident or sudden stop. ● Head restraints should be adjusted properly as they may provide significant protection against injury in an accident. Always replace and adjust them properly if they have been removed for any reason. LRS0290 s 4 Then fold the entire seat forward into the stowed position in the floor. ● If the head restraints are removed for any reason, they should be securely stored to prevent them from causing injury to passengers or damage to the vehicle in case of sudden braking or an accident. ● When the vehicle is being used to carry cargo, properly secure all cargo to help prevent it from sliding or shifting. Do not place cargo higher than the seatbacks. In a sudden stop or collision, unsecured cargo could cause personal injury. 1-12 Safety—Seats, seat belts and supplemental air bags Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X 1 s To fold the 3rd row bench seat flat into the floor, for maximum cargo hauling, remove all three head restraints. Remove the head restraint by lifting up, then push and hold the release button and continue lifting. Then place them in the storage bag. Make sure to secure the storage bag. See “Head restraint storage” in the “Instrument and controls” section of this Owner’s Manual. WARNING LRS0291 Folding the 3rd row bench seat WARNING ● The 3rd row bench seat is heavy. Be careful when folding and unfolding. ● To avoid injury to yourself or others, keep hands and body clear of floor opening when folding. If the head restraints are removed for any reason, they should be securely stored to prevent them from causing injury to passengers or damage to the vehicle in case of sudden braking or an accident. WRS0321 s 2 Disconnect and secure the center seat belt and tongues into the retractor base. See “Stowing rear center seat belt” later in this section. Then push the button in the center of the seatback while pulling back on the pull strap to release the back of the seat. Rotate the seatback toward the back of the vehicle. Safety—Seats, seat belts and supplemental air bags 1-13 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X LRS0292 s 3 Pull up on the lever located on the back of the seat base. This will fold the seat base toward the back of the vehicle. LRS0293 s 4 The entire seat will rotate toward you and stow flat in the floor. LRS0285 s 5 The rear seat anchors are spring loaded and can be folded into the side panels to maximize cargo space. The anchors are held in the folded position by the items in the cargo area. When the load is removed from the cargo area, the rear seat anchors automatically return to the unfolded position. 6. Reverse this process to return the bench seat to a seating position. Make sure to properly install the head restraints, push the bench seat down into the floor, and pull back on the seatback until they latch into place. 1-14 Safety—Seats, seat belts and supplemental air bags Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X SUPPLEMENTAL RESTRAINT SYSTEM WARNING ● When the vehicle is being used to carry cargo, properly secure all cargo to help prevent it from sliding or shifting. Do not place cargo higher than the seatbacks. In a sudden stop or collision, unsecured cargo could cause personal injury. ● When returning the seatbacks to the upright position, be certain they are completely secured in the latched position. If they are not completely secured, passengers may be injured in an accident or sudden stop. ● Head restraints should be adjusted properly as they may provide significant protection against injury in an accident. Always replace and adjust them properly if they have been removed for any reason. ● Never allow anyone to ride in the cargo area or on the rear seat when it is in the fold-down position. Use of these areas by passengers without proper restraints could result in serious injury in an accident or sudden stop. PRECAUTIONS ON SUPPLEMENTAL RESTRAINT SYSTEM This Supplemental Restraint System (SRS) section contains important information concerning the driver and passenger supplemental front air bags (NISSAN Advanced Air Bag System), supplemental side air bags, curtain side-impact air bags and pre-tensioner seat belts. Supplemental front impact air bag system: The NISSAN advanced air bag system can help cushion the impact force to the head and chest of the driver and front passenger in certain frontal collisions. Supplemental side-impact air bag system (if so equipped): This system can help cushion the impact force to the chest area of the driver and front passenger in certain side impact collisions. The supplemental side air bag is designed to inflate on the side where the vehicle is impacted. These supplemental restraint systems are designed to supplement the crash protection provided by the seat belts and are not a substitute for them. Seat belts should always be correctly worn and the occupant seated a suitable distance away from the steering wheel, instrument panel and door finishers. See “Seat belts” later in this section for instructions and precautions on seat belt usage. The supplemental air bags operate only when the ignition switch is in the ON or START position. After turning the ignition key to the ON position, the supplemental air bag warning light illuminates. The supplemental air bag warning light will turn off after about 7 seconds if the system is operational. Supplemental curtain side-impact air bag system: This system can help cushion the impact force to the head of occupants in front and rear outboard seating positions in certain side impact collisions. The curtain side-impact air bags are designed to inflate on the side where the vehicle is impacted. Safety—Seats, seat belts and supplemental air bags 1-15 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X WRS0031 WARNING ● The supplemental front air bags ordinarily will not inflate in the event of a side impact, rear impact, rollover, or lower severity frontal collision. Also, the front passenger air bag will not inflate if the passenger air bag status light is lit. Always wear your seat belts to help reduce the risk or severity of injury in various kinds of accidents. ● The seat belts and the supplemental front air bags are most effective when you are sitting well back and upright in the seat. The front air bags inflate with great force. Even with the NISSAN advanced air bag system, if you are unrestrained, leaning forward, sitting sideways or out of position in any way, you are at greater risk of injury or death in a crash. You may also receive serious or fatal injuries from the supplemental front air bag if you are up against it when it inflates. Always sit back against the seatback and as far away as practical from the steering wheel or instrument panel. Always use the seat belts. ● The driver and front passenger seat belt buckles are equipped with sensors that detect if the seat belts are fastened. The advanced air bag system monitors the severity of a collision and seat belt usage then inflates the air bags. Failure to properly wear seat belts can increase the risk or severity of injury in an accident. 1-16 Safety—Seats, seat belts and supplemental air bags Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X ● The front passenger seat is equipped with an occupant classification sensor (weight sensor) that turns the front passenger air bag OFF under some conditions. This sensor is only used in this seat. Failure to be properly seated and wearing the seat belt can increase the risk or severity of injury in an accident. See “Front Passenger air bag and status light” later in this section. ● Keep hands on the outside of the steering wheel. Placing them inside the steering wheel rim could increase the risk that they are injured when the supplemental front air bag inflates. ARS1133 Safety—Seats, seat belts and supplemental air bags 1-17 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X ARS1041 ARS1042 WARNING ● Never let children ride unrestrained or extend their hands or face out of the window. Do not attempt to hold them in your lap or arms. Some examples of dangerous riding positions are shown in the illustrations. WARNING ● Children may be severely injured or killed when the supplemental front air bags, side air bags or curtain sideimpact air bags inflate if they are not properly restrained. Pre-teens and children should be properly restrained in the rear seat, if possible. 1-18 Safety—Seats, seat belts and supplemental air bags Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X ARS1043 ARS1044 ARS1045 WRS0256 WARNING ● Even with the NISSAN Advanced Air Bag System, never install a rear-facing child restraint in the front seat. An inflating supplemental front air bag could seriously injure or kill your child. See “Child restraints” later in this section for details. Safety—Seats, seat belts and supplemental air bags 1-19 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X WARNING WRS0431 Do not lean against the door. WARNING SSS0162 ● The seat belts, the supplemental side air bags and curtain side-impact air bags are most effective when you are sitting well back and upright in the seat. The side air bag and curtain side-impact air bag inflate with great force. Do not allow anyone to place their hand, leg or face near the side air bag on the side of the seatback of the front seat or near the side roof rails. Do not allow anyone sitting in the front seats or rear outboard seats to extend their hand out of the window or lean against the door. Some examples of dangerous riding positions are shown in the previous illustrations. Supplemental side air bag (if so equipped) and curtain side-impact air bag: ● The supplemental side air bag and curtain side-impact air bag ordinarily will not inflate in the event of a frontal impact, rear impact, rollover or lower severity side collision. Always wear your seat belts to help reduce the risk or severity of injury in various kinds of accidents. 1-20 Safety—Seats, seat belts and supplemental air bags Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X WRS0306 SSS0159 WARNING ● When sitting in the 2nd row rear seat, do not hold onto the seatback of the front seat. If the side air bag inflates, you may be seriously injured. Be especially careful with children, who should always be properly restrained. Some examples of dangerous riding positions are shown in the illustrations. ● Do not use seat covers on the front seatbacks. They may interfere with supplemental side air bag inflation. Safety—Seats, seat belts and supplemental air bags 1-21 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X 10. Satellite sensors 11. Supplemental side air bag modules (if so equipped) 12. SRS curtain side-impact air bag (passenger’s side) NISSAN Advanced Air Bag System (front seats) This vehicle is equipped with the NISSAN advanced air bag system for the driver and front passenger seats. This system is designed to meet certification requirements under U.S. regulations. It is also permitted in Canada. However, all of the information, cautions and warnings in this manual still apply and must be followed. WRS0311 1. 2. 3. 4. SRS curtain side-impact air bag modules SRS curtain side-impact air bag (driver’s side) Seat belt buckle switches Supplemental front air bag modules 5. 6. 7. 8. 9. Crash zone sensor Diagnosis sensor unit Occupant classification system control unit Occupant classification sensor Pre-tensioner retractor The driver supplemental front air bag is located in the center of the steering wheel. The passenger supplemental front air bag is mounted in the dashboard above the glove box. The supplemental front air bags are designed to inflate in higher severity frontal collisions, although they may inflate if the forces in another type of collision are similar to those of a higher severity frontal impact. They may not inflate in certain frontal collisions. Vehicle damage (or lack of it) is not always an indication of proper supplemental front air bag system operation. 1-22 Safety—Seats, seat belts and supplemental air bags Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X The NISSAN advanced air bag system has dual stage inflators. It also monitors information from the crash zone sensor, the diagnosis sensor unit, seat belt buckle sensors, occupant classification sensor (weight sensor) and passenger seat belt tension sensor. Inflator operation is based on the severity of a collision and seat belt usage for the driver. For the front passenger, it additionally monitors the weight of an occupant or object on the seat and seat belt tension. Based on information from the sensors, only one front air bag may inflate in a crash, depending on the crash severity and whether the front occupants are belted or unbelted. Additionally, the front passenger air bag may be automatically turned OFF under some conditions, depending on the weight detected on the passenger seat and how the seat belt is used. If the front passenger air bag is OFF, the passenger air bag status light will be illuminated. See “Front passenger air bag and status light” later in this section for further details. One front air bag inflating does not indicate improper performance of the system. If you have any questions about your air bag system, please contact NISSAN or your NISSAN dealer. If you are considering modification of your vehicle due to a disability, you may also contact NISSAN. Contact information is contained in the front of this Owner’s Manual. When a supplemental front air bag inflates, a fairly loud noise may be heard, followed by the release of smoke. This smoke is not harmful and does not indicate a fire. Care should be taken to not inhale it, as it may cause irritation and choking. Those with a history of a breathing condition should get fresh air promptly. After turning the ignition key to the ON position, the supplemental air bag warning light illuminates. The supplemental air bag warning light will turn off after about 7 seconds if the system is operational. Supplemental front air bags, along with the use of seat belts, help to cushion the impact force on the face and chest of the front occupants. They can help save lives and reduce serious injuries. However, an inflating front air bag may cause facial abrasions or other injuries. Front air bags do not provide restraint to the lower body. Even with NISSAN advanced air bags, seat belts should be correctly worn and the driver and passenger seated upright as far as practical away from the steering wheel or instrument panel. The supplemental front air bags inflate quickly in order to help protect the front occupants. Because of this, the force of the front air bag inflating can increase the risk of injury if the occupant is too close to, or is against, the front air bag module during inflation. The front air bags deflate quickly after a collision. The supplemental front air bags operate only when the ignition switch is in the ON or START position. Safety—Seats, seat belts and supplemental air bags 1-23 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X passenger air bag is OFF, it will not inflate in a crash. The driver air bag and other air bags in your vehicle are not part of this system. The purpose of the regulation is to help reduce the risk of injury or death from an inflating air bag to certain front passenger seat occupants, such as children, by requiring the air bag to be automatically turned OFF. Certain sensors are used to meet the requirements. WRS0314 Front passenger air bag and status light WARNING The front passenger air bag is designed to automatically turn OFF under some conditions. Read this section carefully to learn how it operates. Proper use of the seat, seat belt and child restraints is necessary for most effective protection. Failure to follow all instructions in this manual concerning the use of seats, seat belts and child restraints can increase the risk or severity of injury in an accident. LRS0316 Status light The front passenger air bag status light or is located in the meters and gauges area of the instrument panel. It will illuminate to indicate that the front passenger air bag is OFF and will not inflate in a crash. The light will illuminate if the front passenger seat is unoccupied or when other conditions are met as outlined in this section. Front passenger air bag The front passenger air bag is designed to automatically turn OFF when the vehicle is operated under some conditions as described below in accordance with U.S. regulations. If the front One sensor used is the occupant classification sensor (weight sensor). It is in the bottom of the front passenger seat cushion and is designed to detect an occupant and objects on the seat by weight. It works together with seat belt sensors described later. For example, if a child is in the front passenger seat, the advanced air bag system is designed to turn the passenger air bag OFF in accordance with the regulations. Also, if a child restraint of the type specified in the regulations is on the seat, its weight and the child’s weight can be detected and cause the air bag to turn OFF. Weight sensor operation can vary depending on the front passenger seat belt sensors. The front passenger seat belt sensors are designed to detect if the seat belt is buckled and the amount of tension on the seat belt, such as when it is in the automatic locking mode (child restraint mode). Based on the weight on the seat detected by the weight sensor and the belt tension de- 1-24 Safety—Seats, seat belts and supplemental air bags Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X tected on the seat belt, the advanced air bag system determines whether the front passenger air bag should be automatically turned OFF as required by the regulations. Front passenger seat adult occupants who are properly seated and using the seat belt as outlined in this manual should not cause the passenger air bag to be automatically turned OFF. For small adults it may be turned OFF. Also, if the occupant takes his/her weight off the seat cushion (for example, by not sitting upright, by sitting on an edge of the seat, or by otherwise being out of position), this could cause the sensor to turn the air bag OFF. In addition, if the occupant improperly uses the seat belt in the automatic locking mode (child restraint mode), this could cause the air bag to be turned OFF. Always be sure to be seated and wearing the seat belt properly for the most effective protection by the seat belt and supplemental air bag. NISSAN recommends that pre-teens and children be properly restrained in a rear seat. NISSAN also recommends that appropriate child restraints and booster seats be properly installed in a rear seat. If this is not possible, the weight sensor and seat belt sensors are designed to operate as described above to turn the front passenger air bag OFF for specified child restraints as required by the regulations. Failing to properly secure child restraints and to use the automatic locking mode (child restraint mode) may allow the restraint to tip or move in an accident or sudden stop. This can also result in the passenger air bag inflating in a crash instead of being OFF. See “Child restraints” later in this section for proper use and installation. If the front passenger seat is not occupied and the seat belt is not buckled, the passenger air bag is designed not to inflate in a crash. However, heavy objects placed on the seat could result in air bag inflation, because of the object’s weight detected by the weight sensor. Other conditions could also result in air bag inflation, such as if a child is standing on the seat, or if two children are on the seat, contrary to the instructions in this manual. Always be sure that you and all vehicle occupants are seated and restrained properly. Using the passenger air bag status light, you can monitor when the front passenger air bag is automatically turned OFF. The light will illuminate (indicating the air bag is OFF and will not inflate) when the front passenger seat is not occupied. If an adult occupant is in the seat and the passenger air bag status light is illuminated (indicating that the air bag is OFF), it could be that the person is a small adult, not sitting on the seat, or using the seat belt properly. If a child restraint must be used in the front seat, but the status light is not lit (indicating that the air bag might inflate in a crash), it could be that the child restraint or seat belt is not being used properly. If such situations happen, properly position and restrain the occupant or child restraint. Otherwise reposition the occupant or child restraint in a rear seat. If a malfunction occurs in the front passenger air bag system, the passenger air bag status light or will illuminate and the , located supplemental air bag warning light in the meter and gauges area in the center of the instrument panel, will blink. Have the system checked by a NISSAN dealer. Other supplemental front air bag precautions WARNING ● Do not place any objects on the steering wheel pad or on the instrument panel. Also, do not place any objects between any occupant and the steering wheel or instrument panel. Such objects may become dangerous projectiles and cause injury if the supplemental front air bag inflates. ● Immediately after inflation, several front air bag system components will be hot. Do not touch them; you may severely burn yourself. Safety—Seats, seat belts and supplemental air bags 1-25 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X ● No unauthorized changes should be made to any components or wiring of the supplemental air bag system. This is to prevent accidental inflation of the supplemental air bag or damage to the supplemental air bag system. ● Do not make unauthorized changes to your vehicle’s electrical system, suspension system or front end structure. This could affect proper operation of the supplemental front air bag system. ● Tampering with the supplemental front air bag system may result in serious personal injury. Tampering includes changes to the steering wheel and the instrument panel assembly by placing material over the steering wheel pad and above the instrument panel or by installing additional trim material around the air bag system. ● Modifying or tampering with the front passenger seat may result in serious personal injury. For example, do not change the front seats by placing material on the seat cushion or by installing additional trim material, such as seat covers, on the seat. Additionally, do not stow any objects under the front passenger seat or the seat cushion and seatback. Such objects may interfere with the proper operation of the occupant classification system (weight sensor). ● A cracked windshield should be replaced immediately by a qualified repair facility. A cracked windshield could affect inflation of the supplemental air bag system. ● The SRS wiring harness connectors are yellow and orange for easy identification. When selling your vehicle, we request that you inform the buyer about the supplemental front air bag system and guide the buyer to the appropriate sections in this Owner’s Manual. ● No unauthorized changes should be made to any components or wiring of the seat belt system. This may affect the supplemental front air bag system. Tampering with the seat belt system may result in serious personal injury. ● Work on and around the supplemental front air bag system should be done by a NISSAN dealer. Installation of electrical equipment should also be done by a NISSAN dealer. The Supplemental Restraint System (SRS) wiring should not be modified or disconnected. Unauthorized electrical test equipment and probing devices should not be used on the air bag system. 1-26 Safety—Seats, seat belts and supplemental air bags Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X severity side collisions, although they may inflate if the forces in another type of collision are similar to those of a higher severity side impact. They are designed to inflate on the side where the vehicle is impacted. They may not inflate in certain side collisions. Vehicle damage (or lack of it) is not always an indication of proper supplemental side air bag and curtain side-impact air bag operation. Supplemental side-impact air bag (if so equipped) and curtain side-impact air bags system When the supplemental side air bag and curtain side-impact air bag inflate, a fairly loud noise may be heard, followed by release of smoke. This smoke is not harmful and does not indicate a fire. Care should be taken not to inhale it, as it may cause irritation and choking. Those with a history of a breathing condition should get fresh air promptly. The supplemental side-impact air bags are located in the outside of the seatback of the front seats. The supplemental curtain side-impact air bags are located in the side roof rails. These systems are designed to meet voluntary guidelines to help reduce the risk of injury to out-ofposition occupants. However, all of the information, cautions and warnings in this manual still apply and must be followed. The supplemental side air bags and curtain sideimpact air bags are designed to inflate in higher Supplemental side air bags, along with the use of seat belts, help to cushion the impact force on the chest of the front occupants. Curtain sideimpact air bags help to cushion the impact force to the head of occupants in the front and rear outboard seating positions. They can help save lives and reduce serious injuries. However, an inflating side air bag and curtain side-impact air bag may cause abrasions or other injuries. Supplemental side air bags and curtain sideimpact air bags do not provide restraint to the lower body. LRS0259 The seat belts should be correctly worn and the driver and passenger seated upright as far as practical away from the supplemental side air bag. Rear seat passengers should be seated as far away as practical from the door finishers and side roof rails. The side air bags and curtain side-impact air bag inflate quickly in order to help protect the front and rear outboard occupants. Because of this, the force of the side air bag and curtain side-impact air bag inflating can increase the risk of injury if the occupant is too close to, or is against, these air bag modules during inflation. The side air bag and curtain side-impact air bag will deflate quickly after the collision is over. The supplemental side air bags and curtain side-impact air bags operate only when the ignition switch is in the ON or START positions. After turning the ignition key to the ON position, the supplemental air bag warning light illuminates. The supplemental air bag warning light will turn off after about 7 seconds if the system is operational. Safety—Seats, seat belts and supplemental air bags 1-27 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X WARNING ● Do not place any objects near the seatback of the front seats. Also, do not place any objects (an umbrella, bag, etc.) between the front door finisher and the front seat. Such objects may become dangerous projectiles and cause injury if the supplemental side air bag inflates. ● Right after inflation, several side air bag and curtain side-impact air bag system components will be hot. Do not touch them; you may severely burn yourself. ● No unauthorized changes should be made to any components or wiring of the side air bag and curtain side-impact air bag system. This is to prevent accidental inflation of the side air bag and curtain side-impact air bag or damage to the side air bag and curtain sideimpact air bag system. ● Do not make unauthorized changes to your vehicle’s electrical system, suspension system or side panel. This could affect proper operation of the supplemental side air bag and curtain side-impact air bag system. ● Tampering with the supplemental side air bag system may result in serious personal injury. For example, do not change the front seats by placing material near the seatback or by installing additional trim material, such as seat covers, around the side air bag. ● Work around and on the side air bag and curtain side-impact air bag system should be done by a NISSAN dealer. Installation of electrical equipment should also be done by a NISSAN dealer. The SRS wiring harnesses* should not be modified or disconnected. Unauthorized electrical test equipment and probing devices should not be used on the side air bag system. * The SRS wiring harness connectors are yellow and orange for easy identification. When selling your vehicle, we request that you inform the buyer about the supplemental side air bag and curtain side-impact air bag system and guide the buyer to the appropriate sections in this Owner’s Manual. Pre-tensioner seat belt system (For front seats) WARNING ● The pre-tensioner seat belt cannot be reused after activation. It must be replaced together with the retractor and buckle as a unit. ● If the vehicle becomes involved in a frontal collision but the pre-tensioner is not activated, be sure to have the pretensioner system checked and, if necessary, replaced by your NISSAN dealer. ● No unauthorized changes should be made to any components or wiring of the pre-tensioner seat belt system. This is to prevent accidental activation of the pre-tensioner seat belt or damage to the pre-tensioner seat belt operation. Tampering with the pre-tensioner seat belt system may result in serious personal injury. 1-28 Safety—Seats, seat belts and supplemental air bags Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X ● Work around and on the pre-tensioner system should be done by a NISSAN dealer. Installation of electrical equipment should also be done by a NISSAN dealer. Unauthorized electrical test equipment and probing devices should not be used on the pre-tensioner seat belt system. ● If you need to dispose of the pretensioner or scrap the vehicle, contact a NISSAN dealer. Correct pre-tensioner disposal procedures are set forth in the appropriate NISSAN Service Manual. Incorrect disposal procedures could cause personal injury. The front seat pre-tensioner seat belt system activates in conjunction with the supplemental air bag systems. Working with the seat belt retractor, it helps tighten the seat belt when the vehicle becomes involved in certain types of collisions, helping to restrain front seat occupants. The pre-tensioner is encased with the seat belt’s retractor. These seat belts are used the same as conventional seat belts. cause irritation and choking. Those with a history of a breathing condition should get fresh air promptly. After the pre-tensioner seat belts have activated, load limiters allow the seat belt to release webbing (if necessary) to reduce forces against the chest. If any abnormality occurs in the pre-tensioner system, the supplemental air bag warning light will not come on, will flash intermittently or will turn on for 7 seconds and remain on after the ignition key has been turned to the ON or START position. In this case, the pre-tensioner seat belt may not function properly. They must be checked and repaired. Take your vehicle to the nearest NISSAN dealer. When selling your vehicle, we request that you inform the buyer about the pre-tensioner seat belt system and guide the buyer to the appropriate sections in this Owner’s Manual. LRS0318 1. 2. SRS Air Bag Warning Labels SRS Side Air Bag Warning Label (if so equipped) SUPPLEMENTAL AIR BAG WARNING LABELS Warning labels about the supplemental front air bag and supplemental side air bag systems (if so equipped) are placed in the vehicle as shown in the illustration. When the pre-tensioner seat belt activates, smoke is released and a loud noise may be heard. This smoke is not harmful and does not indicate a fire. Care should be taken not to inhale it, as it may Safety—Seats, seat belts and supplemental air bags 1-29 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X When the ignition key is in the ON or START position, the supplemental air bag warning light illuminates for about 7 seconds and then turns off. This means the system is operational. If any of the following conditions occur, the supplemental front air bag, supplemental side air bag and curtain side-impact air bag and pretensioner seat belt systems need servicing: ● The supplemental air bag warning light remains on after approximately 7 seconds. ● The supplemental air bag warning light flashes intermittently. LRS0100 SUPPLEMENTAL AIR BAG WARNING LIGHT The supplemental air bag warning light, displaying in the instrument panel, monitors the circuits of the supplemental front air bag, supplemental side air bag and curtain sideimpact air bag and pre-tensioner seat belt systems. The circuits monitored by the supplemental air bag warning light are the diagnosis sensor unit, crash zone sensor, satellite sensors, front air bag modules, side air bag modules, curtain sideimpact air bag modules, pre-tensioner seat belts and all related wiring. ● The supplemental air bag warning light does not come on at all. Under these conditions, the supplemental front air bag, supplemental side air bags and curtain side-impact air bag or pre-tensioner seat belt systems may not operate properly. It must be checked and repaired. Take your vehicle to the nearest NISSAN dealer. WARNING If the supplemental air bag warning light is on, it could mean that the supplemental front air bag, supplemental side air bag, curtain side-impact air bag systems and/or pre-tensioner seat belt systems will not operate in an accident. Repair and replacement procedure The supplemental front air bags, supplemental side air bags, curtain side-impact air bags and pre-tensioner seat belts are designed to inflate on a one-time-only basis. As a reminder, unless it is damaged, the supplemental air bag warning light remains illuminated after inflation has occurred. Repair and replacement of these supplemental air bag systems should be done only by a NISSAN dealer. When maintenance work is required on the vehicle, the supplemental front air bags, supplemental side air bags, curtain side-impact air bags, pre-tensioner seat belts and related parts should be pointed out to the person performing the maintenance. The ignition key should always be in the LOCK position when working under the hood or inside the vehicle. 1-30 Safety—Seats, seat belts and supplemental air bags Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X SEAT BELTS WARNING ● Once a supplemental front air bag, supplemental side air bag or curtain side-impact air bag has inflated, the air bag module will not function again and must be replaced. Additionally, if any of the supplemental front air bags inflate, the activated pre-tensioner seat belts must also be replaced. The air bag module and pre-tensioner seat belt system should be replaced by a NISSAN dealer. The air bag module and pre-tensioner seat belt system cannot be repaired. ● The supplemental front air bag, side air bag and curtain side-impact air bag systems, and the pre-tensioner seat belt system should be inspected by a NISSAN dealer if there is any damage to the front end or side portion of the vehicle. ● If you need to dispose of the supplemental air bag, pre-tensioner seat belt system or scrap the vehicle, contact a NISSAN dealer. Correct supplemental air bag and pre-tensioner seat belt system disposal procedures are set forth in the appropriate NISSAN Service Manual. Incorrect disposal procedures could cause personal injury. SSS0136 PRECAUTIONS ON SEAT BELT USAGE If you are wearing your seat belt properly adjusted and you are sitting upright and well back in your seat, your chances of being injured or killed in an accident and/or the severity of injury may be greatly reduced. NISSAN strongly encourages you and all of your passengers to buckle up every time you drive, even if your seating position includes a supplemental air bag. Most U.S. states and Canadian provinces or territories specify that seat belts be worn at all times when a vehicle is being driven. Safety—Seats, seat belts and supplemental air bags 1-31 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X SSS0134 WARNING ● Every person who drives or rides in this vehicle should use a seat belt at all times. Children should be properly restrained in the rear seat and, if appropriate, in a child restraint. SSS0016 WARNING ● The seat belt should be properly adjusted to a snug fit. Failure to do so may reduce the effectiveness of the entire restraint system and increase the chance or severity of injury in an accident. Serious injury or death can occur if the seat belt is not worn properly. 1-32 Safety—Seats, seat belts and supplemental air bags Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X ● Be sure the seat belt tongue is securely fastened to the proper buckle. ● Do not wear the seat belt inside out or twisted. Doing so may reduce its effectiveness. ● Do not allow more than one person to use the same seat belt. ● Never carry more people in the vehicle than there are seat belts. SSS0014 WARNING ● Always route the shoulder belt over your shoulder and across your chest. Never run the belt behind your back, under your arm or across your neck. The belt should be away from your face and neck, but not falling off your shoulder. ● Position the lap belt as low and snug as possible AROUND THE HIPS, NOT THE WAIST. A lap belt worn too high could increase the risk of internal injuries in an accident. ● If the seat belt warning light glows continuously while the ignition is turned ON with all doors closed and all seat belts fastened, it may indicate a malfunction in the system. Have the system checked by a NISSAN dealer. ● Once the pre-tensioner seat belt has activated, it cannot be reused and must be replaced together with the retractor. See your NISSAN dealer. ● Removal and installation of the pretensioner seat belt system components should be done by a NISSAN dealer. ● All seat belt assemblies, including retractors and attaching hardware, should be inspected after any collision by a NISSAN dealer. NISSAN recommends that all seat belt assemblies in use during a collision be replaced unless the collision was minor and the belts show no damage and continue to operate properly. Seat belt assemblies not in use during a collision should also be inspected and replaced if either damage or improper operation is noted. ● All child restraints and attaching hardware should be inspected after any collision. Always follow the restraint manufacturer’s inspection instructions and replacement recommendations. The child restraints should be replaced if they are damaged. CHILD SAFETY Children need adults to help protect them. They need to be properly restrained. The proper restraint depends on the child’s size. Generally, infants up to about 1 year and less than 20 pounds (9 kg) should be placed in rear facing child restraints. Front facing child restraints are available for children who outgrow rear facing child restraints. Safety—Seats, seat belts and supplemental air bags 1-33 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X WARNING Infants and small children Infants and children need special protection. The vehicle’s seat belts may not fit them properly. The shoulder belt may come too close to the face or neck. The lap belt may not fit over their small hip bones. In an accident, an improperly fitting seat belt could cause serious or fatal injury. Always use appropriate child restraints. NISSAN recommends that infants and small children be placed in child restraints that comply with Federal Motor Vehicle Safety Standards or Canadian Motor Vehicle Safety Standards. You should choose a child restraint that fits your vehicle and always follow the manufacturer’s instructions for installation and use. All U.S. states and Canadian provinces or territories require the use of approved child restraints for infants and small children. See “Child Restraints” later in this section. Children who are too large for child restraints should be seated and restrained by the seat belts which are provided. In addition, there are many types of child restraints available for larger children which should be used for maximum protection. NISSAN recommends that all pre-teens and children be restrained in the rear seat. According to accident statistics, children are safer when properly restrained in the rear seat than in the front seat. This is especially important because your vehicle has a supplemental restraint system (Air bag system) for the front passenger. See “Supplemental restraint system” earlier in this section. Larger children If the child’s seating position has a shoulder belt that fits close to the face or neck, the use of a booster seat (commercially available) may help overcome this. The booster seat should raise the child so that the shoulder belt is properly positioned across the top, middle portion of the shoulder and the lap belt is low on the hips. The booster seat should fit the vehicle seat and have a label certifying that it complies with Federal Motor Vehicle Safety Standards or Canadian Motor Vehicle Safety Standards. Once the child has grown so the shoulder belt is no longer on or near the face and neck, use the shoulder belt without the booster seat. WARNING Never let a child stand or kneel on any seat and do not allow a child in the cargo areas while the vehicle is moving. The child could be seriously injured or killed in an accident or sudden stop. PREGNANT WOMEN NISSAN recommends that pregnant women use seat belts. The seat belt should be worn snug, and always position the lap belt as low as possible around the hips, not the waist. Place the shoulder belt over your shoulder and across your chest. Never run the lap/shoulder belt over your abdominal area. Contact your doctor for specific recommendations. INJURED PERSONS NISSAN recommends that injured persons use seat belts. Check with your doctor for specific recommendations. 1-34 Safety—Seats, seat belts and supplemental air bags Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X THREE-POINT TYPE SEAT BELT WITH RETRACTOR WARNING ● Every person who drives or rides in this vehicle should use a seat belt at all times. ● Do not ride in a moving vehicle when the seatback is reclined. This can be dangerous. The shoulder belt will not be against your body. In an accident, you could be thrown into it and receive neck or other serious injuries. You could also slide under the lap belt and receive serious internal injuries. ● For the most effective protection when the vehicle is in motion, the seat should be upright. Always sit well back in the seat and adjust the seat belt properly. Fastening the seat belts 1. Adjust the seat. See “Seats” earlier in this section. WRS0137 s 2 Slowly pull the seat belt out of the retractor and insert the tongue into the buckle until you hear and feel the latch engage. The retractor is designed to lock during a sudden stop or on impact. A slow pulling motion permits the seat belt to move, and allows you some freedom of movement in the seat. WRS0138 3 s Position the lap belt portion low and snug on the hips as shown. 4 s Pull the shoulder belt portion toward the retractor to take up extra slack. Be sure the shoulder belt is routed over your shoulder and across your chest. The front passenger seat, 2nd row captain’s chairs and the rear bench seat three-point seat belts have a cinching mechanism for child restraint installation. It is referred to as the automatic locking mode or child restraint mode. When automatic locking mode is activated the seat belt cannot be withdrawn again until the seat belt tongue is detached from the buckle and fully Safety—Seats, seat belts and supplemental air bags 1-35 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X retracted. Once retracted, the seat belt is in the emergency locking mode. See “Child restraints” later in this section for more information. To increase your confidence in the seat belts, check the operation as follows. ● Grasp the shoulder belt and pull forward quickly. The retractor should lock and restrict further belt movement. The automatic locking mode should be used only for child restraint installation. During normal seat belt use by a passenger, the locking mode should not be activated. If it is activated it may cause uncomfortable seat belt tension. It can also change the operation of the front passenger air bag. See “Front passenger air bag and status light” earlier in this section. If the retractor does not lock during this check or if you have any questions about seat belt operation, see a NISSAN dealer. WARNING When fastening the seat belts, be certain that the seatbacks are completely secured in the latched position. If they are not completely secured, passengers may be injured in an accident or sudden stop. WRS0139 Unfastening the seat belts 1 s To unfasten the seat belt, press the button on the buckle. The seat belt automatically retracts. Checking seat belt operation Seat belt retractors are designed to lock seat belt movement by two separate methods: ● When the seat belt is pulled quickly from the retractor. ● When the vehicle slows down rapidly. 1-36 Safety—Seats, seat belts and supplemental air bags Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X SSS0240 Center of the 3rd row bench seat The 3rd row center seat belt has a connector 1 and a seat belt tongue s 2 . Both the tongue s connector tongue and the seat belt tongue must be securely latched for proper seat belt operation. SSS0241 WARNING ● Always fasten the connector tongue and the seat belt in the order shown. ● Always make sure both the connector tongue and the seat belt tongue are secured when using the seat belt. Do not use it with only the seat belt tongue attached. This could result in serious personal injury in case of an accident or a sudden stop. LRS0432 Safety—Seats, seat belts and supplemental air bags 1-37 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X Stowing the 3rd row center seat belt Attaching the 3rd row center seat belt When folding down the 3rd row seat, the rear center seat belt can be retracted into a stowed position as follows: Always be sure the 3rd row center seat belt connector tongue and connector buckle are attached. Disconnect only when folding down the rear seat. 1 s 2 s 3 s Release the connector tongue by inserting a suitable tool such as key into the connector A. buckle s To connect the buckle: Retract the seat belt up to the retractor base. Insert the seat belt tongue into the fabric sleeve so it will lay flat. Then secure the connector tongue into the retractor base. WARNING ● Do not unfasten the rear center seat belt connector except when folding down the rear seat. Pull out the connector tongue from the retractor base. 2 s Pull out the seat belt tongue from the fabric sleeve. 3 s Pull the seat belt and secure the receiver buckle until it clicks. The center seat belt connector tongue and receiver buckle are indicated by the > and < mark. The center seat belt connector tongue can be attached only into the rear center seat belt connector buckle. ● When attaching the rear center seat belt connector, be certain that the seatbacks are completely secured in the latched position and the rear center seat belt connector is completely secured. ● If the rear center seat belt connector and the seatbacks are not secured in the correct position, serious personal injury may result in an accident or sudden stop. 1 s To fasten the seat belt, see “Fastening the seat belt” earlier in this section. WARNING ● Do not unfasten the rear center seat belt connector except when folding down the rear seat. LRS0433 1-38 Safety—Seats, seat belts and supplemental air bags Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X ● When attaching the rear center seat belt connector, be certain that the seatbacks are completely secured in the latched position and the rear center seat belt connector is completely secured. ● If the rear center seat belt connector and the seatbacks are not secured in the correct position, serious personal injury may result in an accident or sudden stop. LRS0294 Front seats Shoulder belt height adjustment (For front and 2nd row seats) The shoulder belt anchor height should be adjusted to the position best for you. (See “Precautions on seat belt usage” earlier in this section.) 1 the adjustment To adjust, push or pull outs 2 to button and move the shoulder belt anchors the desired position, so the belt passes over the center of the shoulder. The belt should be away from your face and neck, but not falling off your shoulder. Release the adjustment button to lock the shoulder belt anchor into position. LRS0242 2nd row seats WARNING ● After adjustment, release the adjustment button and try to move the shoulder belt anchor up and down to make sure it is securely fixed in position. ● The shoulder belt anchor height should be adjusted to the position best for you. Failure to do so may reduce the effectiveness of the entire restraint system and increase the chance or severity of injury in an accident. Safety—Seats, seat belts and supplemental air bags 1-39 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X CHILD RESTRAINTS SEAT BELT EXTENDERS If, because of body size or driving position, it is not possible to properly fit the lap-shoulder belt and fasten it, an extender is available which is compatible with the installed seat belts. The extender adds approximately 8 inches (200 mm) of length and may be used for either the driver or front passenger seating position. See a NISSAN dealer for assistance if an extender is required. WARNING ● Only NISSAN seat belt extenders, made by the same company which made the original equipment seat belts, should be used with NISSAN seat belts. ● Adults and children who can use the standard seat belt should not use an extender. Such unnecessary use could result in serious personal injury in the event of an accident. SEAT BELT MAINTENANCE ● To clean the seat belt webbing, apply a mild soap solution or any solution recommended for cleaning upholstery or carpet. Then wipe with a cloth and allow the seat belts to dry in the shade. Do not allow the seat belts to retract until they are completely dry. ● If dirt builds up in the shoulder belt guide of the seat belt anchors, the seat belts may retract slowly. Wipe the shoulder belt guide with a clean, dry cloth. ● Periodically check to see that the seat belt and the metal components, such as buckles, tongues, retractors, flexible wires and anchors, work properly. If loose parts, deterioration, cuts or other damage on the webbing is found, the entire seat belt assembly should be replaced. ● Never use seat belt extenders to install child restraints. If the child restraint is not secured properly, the child could be seriously injured in a collision or a sudden stop. ARS1098 PRECAUTIONS ON CHILD RESTRAINTS WARNING ● Infants and small children should always be placed in an appropriate child restraint while riding in the vehicle. Failure to use a child restraint can result in serious injury or death. 1-40 Safety—Seats, seat belts and supplemental air bags Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X ● Never install a rear-facing child restraint in the front seat. An inflating supplemental front air bag could seriously injure or kill your child. A rearfacing child restraint must only be used in the rear seat. ● NISSAN recommends that the child restraint be installed in the rear seat. According to accident statistics, children are safer when properly restrained in the rear seat than in the front seat. WRS0256 WARNING ● Infants and small children should never be carried on your lap. It is not possible for even the strongest adult to resist the forces of a severe accident. The child could be crushed between the adult and parts of the vehicle. Also, do not put the same seat belt around both your child and yourself. ● An improperly installed child restraint could lead to serious injury or death in an accident. In general, child restraints are designed to be installed with the lap portion of a three-point type seat belt. In addition, this vehicle is equipped with a universal child restraint lower anchor system, referred to as the LATCH (Lower Anchors and Tethers for CHildren) system. Some child restraints include two rigid or webbing-mounted attachments that can be connected to these lower anchors. For details, see the “LATCH (Lower Anchors and Tethers for CHildren) system” later in this section. ● Choose only a restraint with a label certifying that it complies with Federal Motor Vehicle Safety Standard 213 or Canadian Motor Vehicle Safety Standard 213. ● Check the child restraint in your vehicle to be sure it is compatible with the vehicle’s seat and seat belt system. ● If the child restraint is compatible with your vehicle, place your child in the child restraint and check the various adjustments to be sure the child restraint is compatible with your child. Always follow all recommended procedures. All U.S. states and provinces of Canada require that infants and small children be restrained in an approved child restraint at all times while the vehicle is being operated. WARNING ● Improper use of a child restraint can increase the risk or severity of injury for both the child and other occupants of the vehicle. Child restraints for infants and small children of various sizes are offered by several manufacturers. When selecting any child restraint, keep the following points in mind: Safety—Seats, seat belts and supplemental air bags 1-41 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X ● Follow all of the child restraint manufacturer’s instructions for installation and use. When purchasing a child restraint, be sure to select one which will fit your child and vehicle. It may not be possible to properly install some types of child restraints in your vehicle. ● If the child restraint is not anchored properly, the risk of a child being injured in a collision or a sudden stop greatly increases. ● Adjustable seatbacks should be positioned to fit the child restraint, but as upright as possible. ● After attaching the child restraint, test it before you place the child in it. Tilt it from side to side. Try to tug it forward and check to see if the belt holds the restraint in place. The child restraint should not move more than 1 inch. If the restraint is not secure, tighten the belt as necessary, or put the restraint in another seat and test it again. ● For a front-facing child restraint, check to make sure the shoulder belt does not go in front of the child’s face or neck. If it does, put the shoulder belt behind the child restraint. If you must install a front facing child restraint in the front seat, see “Installation on front passenger seat” later in this section. ● Failure to use the retractor’s locking mode will result in the child restraint not being properly secured. The restraint could tip over or otherwise be unsecured and cause injury to the child in a sudden stop or collision. ● When your child restraint is not in use, keep it secured with a seat belt to prevent it from being thrown around in case of a sudden stop or accident. CAUTION Remember that a child restraint left in a closed vehicle can become very hot. Check the seating surface and buckles before placing your child in the child restraint. INSTALLATION ON 2ND ROW CAPTAIN’S CHAIRS WARNING ● The three-point seat belt in your vehicle is equipped with an automatic locking mode retractor which must be used when installing a child restraint. 1-42 Safety—Seats, seat belts and supplemental air bags Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X WRS0297 Front Facing — step 1 Front facing When you install a child restraint on the 2nd row captain’s chairs, follow these steps: 1. Position the child restraint on the seat. It can be placed in a front facing direction, depending on the size of the child. Remove the head restraint from the seat back. Store it in a secure place. Always follow the restraint manufacturer’s instructions. WRS0298 Front Facing — step 2 2. Route the seat belt tongue through the child restraint and insert it into the buckle until you hear and feel the latch engage. Be sure to follow the child restraint manufacturer’s instructions for belt routing. WRS0299 Front Facing — step 3 3. Pull on the shoulder belt until all of the belt is fully extended. At this time, the seat belt retractor is in the automatic locking mode (child restraint mode). It reverts back to emergency locking mode when the seat belt is fully retracted. Safety—Seats, seat belts and supplemental air bags 1-43 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X After the child restraint is removed and the seat belt is fully retracted, the automatic locking mode (child restraint mode) is canceled. WRS0146 Front Facing — step 4 4. Allow the seat belt to retract. Pull up on the shoulder belt to remove any slack in the belt. WRS0300 Front Facing — step 5 5. Before placing the child in the child restraint, use force to tilt the child restraint from side to side, and tug it forward to make sure that it is securely held in place. It should not move more than 1 inch (25 mm). 6. Check that the retractor is in the automatic locking mode by trying to pull more seat belt out of the retractor. If you cannot pull any more belt webbing out of the retractor, the retractor is in the automatic locking mode. 7. Check to make sure that the child restraint is properly secured prior to each use. If the belt is not locked, repeat steps 3 through 6. 1-44 Safety—Seats, seat belts and supplemental air bags Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X WRS0301 Rear Facing — step 1 Rear facing When you install a child restraint on the 2nd row captain’s chair, follow these steps: 1. Position the child restraint on the seat. The direction of the child restraint depends on the type of the child restraint and the size of the child. Always follow the restraint manufacturer’s instructions. WRS0302 Rear Facing — step 2 2. Route the seat belt tongue through the child restraint and insert it into the buckle until you hear and feel the latch engage. Be sure to follow the child restraint manufacturer’s instructions for belt routing. WRS0303 Rear Facing — step 3 3. Pull on the shoulder belt until all of the belt is fully extended. At this time, the seat belt retractor is in the automatic locking mode (child restraint mode). It reverts to emergency locking mode when the seat belt is fully retracted. Safety—Seats, seat belts and supplemental air bags 1-45 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X 7. Check to make sure that the child restraint is properly secured prior to each use. If the belt is not locked, repeat steps 3 through 6. After the child restraint is removed and the seat belt fully retracted, the automatic locking mode (child restraint mode) is canceled. INSTALLATION ON 3RD ROW BENCH SEAT WARNING WRS0304 Rear Facing — step 4 4. Allow the seat belt to retract. Pull up on the shoulder belt to remove any slack in the belt. WRS0305 Rear Facing — step 5 5. Before placing the child in the child restraint, use force to tilt the child restraint from side to side, and tug it forward to make sure that it is securely held in place. It should not move more than 1 inch (25 mm). 6. Check that the retractor is in the automatic locking mode by trying to pull more seat belt out of the retractor. If you cannot pull any more seat belt webbing out of the retractor, the retractor is in the automatic locking mode. ● The three-point seat belt in your vehicle is equipped with an automatic locking mode retractor which must be used when installing a child restraint. ● Failure to use the retractor’s locking mode will result in the child restraint not being properly secured. The restraint could tip over or otherwise be unsecured and cause injury to the child in a sudden stop or collision. ● When installing a child restraint system in the rear center position, both the center seat belt connector tongue and buckle tongue must be secured. See “Attaching rear center seat belt” earlier in this section. 1-46 Safety—Seats, seat belts and supplemental air bags Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X WRS0325 Front Facing (outboard) — step 1 Front facing WARNING Front facing child restraints can be installed in all 3rd row bench seat positions. However, front facing child restraints that require the use of a top tether strap can be installed in the center 3rd row position only. Do not install a child restraint requiring a top tether strap in an outboard position and attempt to angle the tether to the 3rd row center anchor. LRS0313 Front Facing (center) — step 1 When you install a child restraint on the 3rd row bench seat, follow these steps: 1. Position the child restraint on the seat. It can be placed in a front facing direction, depending on the size of the child. Remove the head restraint from the seat back. Store it in a secure place. Always follow the restraint manufacturer’s instructions. WRS0250 Front Facing — step 2 2. Route the seat belt tongue through the child restraint and insert it into the buckle until you hear and feel the latch engage. Be sure to follow the child restraint manufacturer’s instructions for belt routing. Safety—Seats, seat belts and supplemental air bags 1-47 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X WRS0251 Front Facing — step 3 3. Pull on the shoulder belt until all of the belt is fully extended. At this time, the seat belt retractor is in the automatic locking mode (child restraint mode). It reverts back to emergency locking mode when the seat belt is fully retracted. WRS0146 Front Facing — step 4 4. Allow the seat belt to retract. Pull up on the shoulder belt to remove any slack in the belt. WRS0252 Front Facing — step 5 5. Before placing the child in the child restraint, use force to tilt the child restraint from side to side, and tug it forward to make sure that it is securely held in place. It should not move more than 1 inch (25mm). 6. Check that the retractor is in the automatic locking mode by trying to pull more seat belt out of the retractor. If you cannot pull any more belt webbing out of the retractor, the retractor is in the automatic locking mode. 7. Check to make sure that the child restraint is properly secured prior to each use. If the belt is not locked, repeat steps 3 through 6. 1-48 Safety—Seats, seat belts and supplemental air bags Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X After the child restraint is removed and the seat belt is fully retracted, the automatic locking mode (child restraint mode) is canceled. WRS0323 Rear Facing (outboard) — step 1 LRS0312 Rear Facing (center) — step 1 Rear facing When you install a child restraint on the 3rd row bench seat, follow these steps: 1. Position the child restraint on the seat. The direction of the child restraint depends on the type of the child restraint and the size of the child. Always follow the restraint manufacturer’s instructions. Safety—Seats, seat belts and supplemental air bags 1-49 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X WRS0309 Rear Facing — step 2 2. Route the seat belt tongue through the child restraint and insert it into the buckle until you hear and feel the latch engage. Be sure to follow the child restraint manufacturer’s instructions for belt routing. WRS0324 Rear Facing — step 3 3. Pull on the shoulder belt until all of the belt is fully extended. At this time, the seat belt retractor is in the automatic locking mode (child restraint mode). It reverts to emergency locking mode when the seat belt is fully retracted. WRS0253 Rear Facing — step 4 4. Allow the seat belt to retract. Pull up on the shoulder belt to remove any slack in the belt. 1-50 Safety—Seats, seat belts and supplemental air bags Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X 7. Check to make sure that the child restraint is properly secured prior to each use. If the belt is not locked, repeat steps 3 through 6. After the child restraint is removed and the seat belt fully retracted, the automatic locking mode (child restraint mode) is canceled. WRS0254 Rear Facing — step 5 5. Before placing the child in the child restraint, use force to tilt the child restraint from side to side, and tug it forward to make sure that it is securely held in place. It should not move more than 1 inch (25mm). WRS0295 LATCH anchor point label (2nd row captain’s chairs) LATCH (Lower Anchors and Tethers for CHildren) SYSTEM 6. Check that the retractor is in the automatic locking mode by trying to pull more seat belt out of the retractor. If you cannot pull any more seat belt webbing out of the retractor, the retractor is in the automatic locking mode. Safety—Seats, seat belts and supplemental air bags 1-51 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X restraint, refer to the illustration for the seating positions equipped with LATCH system anchors which can be used to secure the child restraint. The LATCH system anchors are located at the rear of the seat cushion near the seatback. A label is attached to the seatback to help you locate the LATCH system anchors. LATCH child restraints generally require the use of a top tether strap. See “Top tether strap child restraint” later in this section for installation instructions. WRS0436 LATCH anchor point label (3rd row bench seat) WARNING ● Attach LATCH system compatible child restraints only at the locations shown. If a child restraint is not secured properly, your child could be seriously injured or killed in an accident. ● The LATCH system anchors are designed to withstand only those loads imposed by correctly fitted child restraints. Under no circumstance are they to be used for adult seat belts or harnesses. WRS0315 LATCH system anchor locations Some child restraints include two rigid or webbing-mounted attachments that can be connected to two anchors located at certain seating positions in your vehicle. This system is known as the LATCH (Lower Anchors and Tethers for CHildren) system. This system may also be referred to as the ISOFIX or ISOFIX compatible system. With this system, you do not have to use a vehicle seat belt to secure the child restraint. Your vehicle is equipped with special anchor points that are used with LATCH system compatible child restraints. Check your child restraint for a label stating that it is compatible with the LATCH system. This information may also be in the child restraint owner’s manual. If you have such a child When installing a child restraint, carefully read and follow the instructions in this manual and those supplied with the child restraint. When you install a LATCH system compatible child restraint to the lower anchor attachments, follow these steps: WARNING Inspect the lower anchors by inserting your fingers into the lower anchor area and feeling to make sure there are no obstructions over the LATCH system anchors, such as seat belt webbing or seat cushion material. The child restraint will not be secured properly if the LATCH system anchors are obstructed. 1-52 Safety—Seats, seat belts and supplemental air bags Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X 1. To install the LATCH system compatible child restraint, insert the child restraint LATCH system anchor attachments into the anchor points on the seat. If the child restraint is equipped with a top tether, see “Top tether strap child restraint” later in this section for installation instructions. 2. After attaching the child restraint and before placing the child in it, use force to tilt the child restraint from side to side and tug it forward to make sure that the child restraint is securely held in place. It should not move more than 1 inch. 3. Check to make sure that the child restraint is properly secured prior to each use. TOP TETHER STRAP CHILD RESTRAINT If your child restraint has a top tether strap, it must be secured to the anchor point provided behind its position. WARNING ● Child restraint anchor points are designed to withstand only those loads imposed by correctly fitted child restraints. Under no circumstances are they to be used for adult seat belts or harnesses. ● After removing a rear seat head restraint for top tether installation, store it securely to prevent it from causing injury to passengers or damage to the vehicle in case of sudden braking or an accident. Always replace it and adjust properly when top tether is no longer in use. First, secure the child restraint with the seat belt or the LATCH system (2nd row captain’s chairs and the center position of the 3rd row bench seat only), as applicable. For the 2nd and 3rd row seats, remove the head restraint from the seatback. Store it in a secure place. Position the top tether strap over the top of the seatback and secure it to the tether anchor bracket as shown later in this section. Tighten the tether strap according to the manufacturer’s instructions to remove any slack. WARNING A child restraint with a top tether strap can only be used in the 3rd row bench seat, center position. Do not place in an outboard seating position and attempt to angle the tether strap to the center position. For best child restraint fit, see the child restraint installation instructions in this section and the child restraint manufacturer’s instructions. For the front passenger seat in the 2 passenger cargo van only, adjust the head restraint to its highest position and route the top tether strap between the head restraint and the top of the seatback. Secure the tether strap to the tether anchor point on the floor directly behind the seat. Tighten the tether strap according to the manufacturer’s instructions to remove any slack. Safety—Seats, seat belts and supplemental air bags 1-53 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X LRS0322 Front passenger seat (2 passenger cargo van only) WRS0210 Label LRS0307 2nd row captain’s chairs Anchor point locations Anchor points are located on the floor behind the front passenger seat (2 passenger cargo van only), on the back of the 2nd row captain’s chairs and the back of the center seat position on the 3rd row bench seat as shown. If you have any questions when installing a top strap child restraint on the rear seat, consult your NISSAN dealer for details. The front passenger seat and 2nd row captain’s chair anchor point locations are marked with the label shown. 1-54 Safety—Seats, seat belts and supplemental air bags Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X WRS0319 3rd row bench 1. Pull strap 2. Top tether anchor point WRS0256 INSTALLATION ON FRONT PASSENGER SEAT WARNING ● Never install a rear-facing child restraint in the front passenger seat. Supplemental front air bags inflate with great force. A rear-facing child restraint could be struck by the supplemental front air bag in a crash and could seriously injure or kill your child. WRS0378 ● NISSAN recommends that child restraints be installed in the rear seat. However, if you must install a forwardfacing child restraint in the front passenger seat, move the passenger seat to the rearmost position. Also, be sure the front passenger air bag status light is illuminated to indicate the passenger air bag is OFF. See “Front passenger air bag and status light” earlier in this section for details. Safety—Seats, seat belts and supplemental air bags 1-55 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X ● A child restraint with a top tether strap should not be used in the front passenger seat unless the vehicle is the 2 passenger cargo van only. ● The three-point seat belt in your vehicle is equipped with an automatic locking mode retractor which must be used when installing a child restraint. ● Failure to use the retractor’s locking mode will result in the child restraint not being properly secured. The restraint could tip over or otherwise be unsecured and cause injury to the child in a sudden stop or collision. WRS0379 Front Facing — step 1 If you must install a child restraint in the front seat, follow these steps: 1. Position the child restraint on the front passenger seat. It should be placed in a front-facing direction only. Move the seat to the rearmost position. Adjust the head restraint to its highest position. Always follow the child restraint manufacturer’s instructions. Child restraints for infants must be used in the rear-facing direction and therefore must not be used in the front seat. WRS0159 Front Facing — step 2 2. Route the seat belt tongue through the child restraint and insert it into the buckle until you hear and feel the latch engage. Be sure to follow the child restraint manufacturer’s instructions for belt routing. 1-56 Safety—Seats, seat belts and supplemental air bags Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X WRS0160 Front Facing — step 3 3. Pull on the shoulder belt until all of the belt is fully extended. At this time, the seat belt retractor is in the automatic locking mode (child restraint mode). It reverts to emergency locking mode when the seat belt is fully retracted. WRS0161 Front Facing — step 4 4. Allow the seat belt to retract slightly. Pull up on the shoulder belt to remove any slack in the belt. WRS0380 Front Facing — step 5 5. Before placing the child in the child restraint, use force to tilt the child restraint from side to side, and tug it forward to make sure that it is securely held in place. It should not move more than 1 inch. 6. Check that the retractor is in the automatic locking mode by trying to pull more seat belt out of the retractor. If you cannot pull any more belt webbing out of the retractor, the retractor is in the automatic locking mode. Safety—Seats, seat belts and supplemental air bags 1-57 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X 7. Check to make sure the child restraint is properly secured prior to each use. If the seat belt is not locked, repeat steps 3 through 6. 8. Turn the ignition to the ON position. The passenger air bag status light should say “PASS AIR BAG OFF” or . If this light is not illuminated it may indicate a malfunction. Move the child restraint to another seating position. Have the system checked by a NISSAN dealer. After the child restraint is removed and the seat belt is fully retracted, the automatic locking mode (child restraint mode) is canceled. 1-58 Safety—Seats, seat belts and supplemental air bags Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X MEMO Safety—Seats, seat belts and supplemental air bags 1-59 2 Instruments and controls Instrument panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2 Meters and gauges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3 Speedometer and odometer . . . . . . . . . . . . . . . . . . . . . 2-4 Tachometer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4 Engine coolant temperature gauge . . . . . . . . . . . . . . . 2-4 Fuel gauge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5 Warning/indicator lights and audible reminders . . . . . . . 2-6 Checking bulbs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6 Warning lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6 Indicator lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-9 Audible reminders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-12 Security system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-12 Nissan vehicle immobilizer system (NVIS) . . . . . . . . 2-12 Windshield wiper and washer switch . . . . . . . . . . . . . . . 2-13 Switch operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-13 Rear window wiper and washer switch. . . . . . . . . . . . . . 2-14 Rear window and outside mirror (if so equipped) defroster switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-15 Headlight and turn signal switch. . . . . . . . . . . . . . . . . . . . 2-15 Headlight control switch. . . . . . . . . . . . . . . . . . . . . . . . 2-15 Daytime running light system (Canada only) . . . . . . 2-18 Instrument brightness control . . . . . . . . . . . . . . . . . . . 2-18 Turn signal switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-19 Fog light switch (if so equipped) . . . . . . . . . . . . . . . . 2-19 Cornering light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-19 Hazard warning flasher switch . . . . . . . . . . . . . . . . . . . . . 2-20 Horn . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-20 Heated seat (if so equipped). . . . . . . . . . . . . . . . . . . . . . . 2-21 Traction control system (TCS) off switch (if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-22 Vehicle dynamic control (VDC) off switch (if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-22 Rear sonar system off switch (if so equipped). . . . . . . . 2-22 Power outlet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-23 Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-25 Note holder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-25 Upper instrument panel storage compartment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-25 Lower instrument panel storage trays . . . . . . . . . . . . 2-26 Passenger seat storage tray (if so equipped) . . . . . 2-26 Center console. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-27 Glove box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-28 Sunglasses holder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-28 Convenience hook. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-29 Map pockets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-29 Seatback pockets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-30 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X Grocery hooks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-30 Umbrella holder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-30 Overhead console . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-31 Cup holders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-32 3rd row armrest bin . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-33 Cargo area storage bin. . . . . . . . . . . . . . . . . . . . . . . . . 2-34 Garment hook. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-34 Head restraint storage . . . . . . . . . . . . . . . . . . . . . . . . . 2-34 Roof rack (if so equipped) . . . . . . . . . . . . . . . . . . . . . . 2-35 Windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-36 Power windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-36 Power vent windows (if so equipped) . . . . . . . . . . . . 2-38 Manual vent windows (if so equipped) . . . . . . . . . . . 2-38 Skyview™ roof (if so equipped) . . . . . . . . . . . . . . . . . . . . . 2-39 Sunroof (if so equipped). . . . . . . . . . . . . . . . . . . . . . . . . . . 2-39 Automatic sunroof . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-39 Lights on demand switch . . . . . . . . . . . . . . . . . . . . . . . . . . 2-41 Personal lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-42 Map lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-43 HomelinkT universal transceiver (if so equipped) . . . . . 2-43 Programming HomeLinkT. . . . . . . . . . . . . . . . . . . . . . . 2-44 Programming HomeLinkT for Canadian customers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-45 Operating the HomeLinkT universal transceiver. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-45 Programming trouble-diagnosis . . . . . . . . . . . . . . . . . 2-45 Clearing the programmed information . . . . . . . . . . . . 2-46 Reprogramming a single HomeLinkT button . . . . . . 2-46 If your vehicle is stolen . . . . . . . . . . . . . . . . . . . . . . . . . 2-46 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X INSTRUMENT PANEL 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. WIC0599 16. Driver side, center and passenger side ventilators (P. 4-17) Headlight and turn signal switch (P. 2-15) Steering wheel switch for audio control (if so equipped) (P. 4-41) Driver supplemental air bag/horn (P. 1-15, P. 2-20) Cruise control main/set switches (P. 5-12) Windshield wiper/washer switch and rear window wiper/washer switch (P. 2-13, 2-14) Meters and gauges (P. 2-3) Display screen/Navigation system* (P. 4-2, P. 4-8) Warning/indicator lights (P. 2-6) Front passenger supplemental air bag (P. 1-15) Glove box (P. 2-28) Climate controls (P. 4-17, 4-27) Hazard warning flasher switch (P. 2-20) Audio system controls (P. 4-30) Display screen/Navigation system* controls (P. 4-2, 4-8) Shift selector lever (P. 5-7) 2-2 Instruments and controls Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X METERS AND GAUGES 17. 18. 19. 20. 21. 22. Tilt steering wheel control (P. 3-21) Rear sonar system off switch (if so equipped) (P. 2-22) Vehicle dynamic control (VDC) off switch (if so equipped) or Traction control system (TCS) off switch (if so equipped) (P. 2-22, P. 2-22) Lights on demand switch (P. 2-41) Instrument brightness control (P. 2-18) Outside mirror controls (P. 3-24) *: Refer to the separate Navigation System Owner’s Manual (if so equipped). See the page number indicated in parentheses for operating details. LIC0459 1. 2. 3. 4. 5. Tachometer Warning/indicator lights Speedometer Odometer Engine coolant temperature gauge/Fuel gauge Instruments and controls 2-3 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X LIC0460 1. 2. Speedometer Odometer SPEEDOMETER AND ODOMETER Speedometer The speedometer indicates vehicle speed in miles per hour (MPH) and kilometers per hour (km/h). Odometer The odometer records the total distance the vehicle has been driven. LIC0461 TACHOMETER The tachometer indicates engine speed in revolutions per minute (r/min). Do not rev engine into 1 . the red zone s CAUTION When engine speed approaches the red zone, shift to a higher gear. Operating the engine in the red zone may cause serious engine damage. LIC0462 ENGINE COOLANT TEMPERATURE GAUGE NOTE: The ignition key must be in the ON position for the gauge to give a reading. The gauge indicates the engine coolant temperature. The engine coolant temperature is within the 1 when the reading is within the normal range s zone shown in the illustration. The engine coolant temperature varies with the outside air temperature and driving conditions. 2-4 Instruments and controls Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X CAUTION CAUTION ● If the vehicle runs out of fuel, the malfunction indicator lamp (MIL) may come on. Refuel as soon as possible. After a few driving trips, the lamp should turn off. If the lamp remains on after a few driving trips, have the vehicle inspected by a NISSAN dealer. If the gauge indicates engine coolant temperature over the normal range, stop the vehicle as soon as safely possible. If the engine is overheated, continued operation of the vehicle may seriously damage the engine. See “If your vehicle overheats” in the “In case of emergency” section for immediate action required. LIC0463 ● For additional information, see “Malfunction indicator lamp (MIL)” later in this section. FUEL GAUGE NOTE: The ignition key must be in the ON position for the gauge to give a reading. The gauge indicates the approximate fuel level in the tank. The low fuel warning light comes on when the amount of fuel in the tank is getting low. Refill the fuel tank before the gauge registers E (Empty). The indicates that the fuel filler lid is located on the driver’s side of the vehicle. Instruments and controls 2-5 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X WARNING/INDICATOR LIGHTS AND AUDIBLE REMINDERS or Anti-lock brake warning light Seat belt warning light and chime or or Brake warning light Supplemental air bag warning light Security indicator light (NVIS) Charge warning light Automatic transmission position indicator light Slip indicator light Door open warning light Cruise main switch indicator light Traction control system off indicator light (if so equipped) Engine oil pressure warning light Cruise set switch indicator light Turn signal/hazard indicator lights Low fuel warning light High beam indicator light (Blue) Vehicle dynamic control off indicator light (if so equipped) Low tire pressure warning light Malfunction indicator lamp (MIL) Low windshield washer fluid warning light Overdrive off indicator light CHECKING BULBS With all doors closed, apply the parking brake and turn the ignition key to the ON position without starting the engine. The following lights will come on: , or , , , The following lights come on briefly and then go off: , or , , , , , If any light fails to come on, it may indicate a burned-out bulb or an open circuit in the electrical system. Have the system repaired promptly. Front passenger air bag status light WARNING LIGHTS or Anti-lock brake warning light If the light comes on while the engine is running, it may indicate the anti-lock brake system is not functioning properly. Have the system checked by a NISSAN dealer. 2-6 Instruments and controls Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X Turn off the engine, and start it again by slowly turning the ignition key (quickly doing so may cause the ABS light to stay on when there is nothing wrong). If the light stays on, have the system checked by a NISSAN dealer. If an abnormality occurs in the system, the antilock function ceases, but the regular braking system continues to operate. If the light comes on while you are driving, contact a NISSAN dealer for repair. or Brake warning light This light functions for both the parking brake and the foot brake systems. When the ignition key is in the ON position, the light comes on when the parking brake is applied, and also warns of a low brake fluid level. If the light comes on while the engine is running with the parking brake not applied, stop the vehicle and perform the following: 1. Check the brake fluid level. Add brake fluid as necessary. See “Brake fluid” in the “Maintenance and do-it-yourself” section of this manual. 2. If the brake fluid level is correct, have the brake system checked by a NISSAN dealer. WARNING ● Your vehicle is equipped with an automatic engine cooling fan. It may come on at any time without warning, even if the ignition key is in the OFF position and the engine is not running. To avoid injury, always disconnect the negative battery cable before working near the fan. ● Pressing the brake pedal with the engine stopped and/or a low brake fluid level may increase your stopping distance and braking will require greater pedal effort as well as pedal travel. ● If the brake fluid MINIMUM or MIN fluid reservoir, do brake system has NISSAN dealer. level is below the mark on the brake not drive until the been checked at a Charge warning light If this light comes on while the engine is running, it may indicate the charging system is not functioning properly. Turn the engine off and check the generator belt. If the belt is loose, broken, missing, or if the light remains on, see a NISSAN dealer immediately. CAUTION Do not continue driving if the generator belt is loose, broken or missing. Door open warning light This light comes on when any of the doors are not closed securely while the ignition key is in the ON position. Engine oil pressure warning light This light warns of low engine oil pressure. If the light flickers or comes on during normal driving, pull off the road in a safe area, stop the engine immediately and call a NISSAN dealer or other authorized repair shop. The engine oil pressure warning light is not designed to indicate a low oil level. Use the dipstick to check the oil level. See “Engine oil” in the “Maintenance and do-it-yourself” section of this manual. Instruments and controls 2-7 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X CAUTION Running the engine with the engine oil pressure warning light on could cause serious damage to the engine almost immediately. Such damage is not covered by warranty. Turn off the engine as soon as it is safe to do so. Low fuel warning light This light comes on when the fuel level in the fuel tank is getting low. Refuel as soon as it is convenient, preferably before the fuel gauge reaches E (Empty). There will be a small reserve of fuel in the tank when the fuel gauge needle reaches E (Empty). Low tire pressure warning light This light warns of low tire pressure. NISSAN’s low tire pressure warning system is a tire pressure monitoring system. It monitors tire pressure of all tires except the spare. When the tire pressure monitoring system warning light is lit, one or more of your tires is significantly underinflated. You should stop and check your tires as soon as possible, and inflate them to the proper pressure as indicated on the vehicle’s tire information placard. Driving on a significantly under- inflated tire causes the tire to overheat and can lead to tire failure. Under-inflation also reduces fuel efficiency and tire tread life, and may affect the vehicle’s handling and stopping ability. Each tire, including the spare, should be checked monthly when cold and set to the recommended inflation pressure as specified in the vehicle placard and owner’s manual. The recommended inflation pressure may also be found on the Tire and Loading Information Label. Low tire pressure warning: If the vehicle is being driven with very low tire pressure (lower than 28 psi, 193 kPa), the light will illuminate and the chime will sound for about 10 seconds. For additional information, see “Low tire pressure warning system” in the “Starting and driving” section and “Low tire pressure warning system” in the “In case of emergency” section. WARNING ● If the light does not come on with the key switch turned ON, have the vehicle checked by a NISSAN dealer as soon as possible. ● If the light comes on while driving, avoid sudden steering maneuvers or abrupt braking, reduce vehicle speed, pull off the road to a safe location and stop the vehicle as soon as possible. Serious vehicle damage could occur and may lead to an accident and could result in serious personal injury. Check the tire pressure for all four tires. Adjust the tire pressure to the recommended COLD tire pressure shown on the Tire and Loading Information label to turn the low tire pressure warning light OFF. If the light still comes on while driving after adjusting the tire pressure, a tire may be flat. If you have a flat tire, replace it with a spare tire as soon as possible. ● When a spare tire is mounted or a wheel is replaced, tire pressure will not be indicated and the low tire pressure warning system will not function. Contact your NISSAN dealer as soon as possible for tire replacement and/or system resetting. 2-8 Instruments and controls Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X CAUTION ● The low tire pressure warning system is not a substitute for the regular tire pressure check. Be sure to check the tire pressure regularly. ● If the vehicle is being driven at speeds of less than 20 MPH (32 km/h), the low tire pressure warning system may not operate correctly. ● Be sure to install the specified size of tires to the 4 wheels correctly. Low windshield washer fluid warning light This light comes on when the windshield washer fluid is at a low level. Add windshield washer fluid as necessary. See the “Maintenance and do-ityourself” section of this manual. Seat belt warning light and chime The light and chime remind you to fasten your seat belts. The light illuminates whenever the ignition key is turned to the ON or START position and remains illuminated until the driver’s seat belt is fastened. At the same time, the chime sounds for about 7 seconds unless the driver’s seat belt is securely fastened. Refer to “Seat belts” in the “Safety—Seats, seat belts and supplemental air bags” section for precautions on seat belt usage. Supplemental air bag warning light When the ignition key is in the ON or START position, the supplemental air bag warning light illuminates for about 7 seconds and then turns off. This means the system is operational. If any of the following conditions occur, the supplemental front air bag, supplemental side air bag (if so equipped), curtain side-impact air bags, and pre-tensioner seat belt systems need servicing and your vehicle must be taken to a NISSAN dealer: ● The supplemental air bag warning light remains on after approximately 7 seconds. ● The supplemental air bag warning light flashes intermittently. ● The supplemental air bag warning light does not come on at all. Unless checked and repaired, the supplemental restraint system (air bag system) and/or the pretensioner seat belts may not function properly. For additional details see “Supplemental restraint system” in the “Safety—Seats, seat belts and supplemental air bags” section of this manual. WARNING If the supplemental air bag warning light is on, it could mean that the supplemental front air bag, supplemental side air bag, curtain side-impact air bag systems (if so equipped) and/or pre-tensioner seat belt systems will not operate in an accident. INDICATOR LIGHTS Automatic transmission position indicator light When the ignition key is turned to the ON position, the indicator in the tachometer shows the automatic transmission selector lever position. See “Driving the vehicle” in the “Starting and driving” section of this manual. Cruise main switch indicator light The light comes on when the cruise control main switch is pushed. The light goes out when the main switch is pushed again. When the cruise main switch indicator light comes on, the cruise control system is operational. Instruments and controls 2-9 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X Cruise set switch indicator light The light comes on while the vehicle speed is controlled by the cruise control system. If the light blinks while the engine is running, it may indicate the cruise control system is not functioning properly. Have the system checked by a NISSAN dealer. High beam indicator light (Blue) This blue light comes on when the headlight high beams are on and goes out when the low beams are selected. The high beam indicator light also comes on when the passing signal is activated. Malfunction indicator lamp (MIL) If this indicator lamp comes on steady or blinks while the engine is running, it may indicate a potential emission control malfunction. The malfunction indicator lamp may also come on steady if the fuel filler cap is loose or missing, or if the vehicle runs out of fuel. Check to make sure the fuel filler cap is installed and closed tightly, and that the vehicle has at least 3 gallons of fuel in the fuel tank. lamp should After a few driving trips, the turn off if no other potential emission control system malfunction exists. Operation The malfunction indicator lamp will come on in one of two ways: ● Malfunction indicator lamp on steady — An emission control system malfunction has been detected. Check the fuel filler cap. If the fuel filler cap is loose or missing, tighten or install the cap and continue to drive the vehicle. The lamp should turn off after a few driving trips. If the lamp does not turn off after a few driving trips, have the vehicle inspected by a NISSAN dealer. You do not need to have your vehicle towed to the dealer. ● Malfunction indicator lamp blinking — An engine misfire has been detected which may damage the emission control system. To reduce or avoid emission control system damage: – do not drive at speeds above 45 MPH (72 km/h). – avoid hard acceleration or deceleration. – avoid steep uphill grades. – if possible, reduce the amount of cargo being hauled or towed. The malfunction indicator lamp may stop blinking and come on steady. Have the vehicle inspected by a NISSAN dealer. You do not need to have your vehicle towed to the dealer. CAUTION Continued vehicle operation without having the emission control system checked and repaired as necessary could lead to poor driveability, reduced fuel economy, and possible damage to the emission control system. Overdrive off indicator light This light comes on when the overdrive function is OFF. The automatic transmission overdrive function is controlled by the overdrive switch. See “Driving the vehicle” in the “Starting and driving” section of this manual. or Front passenger air bag status light The front passenger air bag status light ( or ) will be lit and the passenger front air bag will be OFF depending on how the front passenger seat is being used. 2-10 Instruments and controls Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X For front passenger air bag status light operation, see “Front passenger air bag and status light” in the “Safety — Seats, seat belts and supplemental air bags” section of this manual. Security indicator light (NVIS) This light blinks whenever the ignition switch is in the LOCK, OFF or ACC position. This function indicates the security system equipped on the vehicle is operational. For additional information, see “Security system” later in this section. Slip indicator light This indicator light will blink when the traction control system is limiting wheel spin. Slippery road conditions may exist if the slip indicator blinks on. If this happens, adjust your driving accordingly. The slip indicator light also comes on when you turn the ignition key to the ON position. The light will turn off after about 2 seconds if the system is operational. If the light does not come on or go off, have the traction control system checked by a NISSAN dealer. The system operates in all transmission shift lever positions, but the system can upshift the transmission only as high as the indicated shift lever position. Traction control system off indicator light (if so equipped) This indicator light comes on when the traction control off switch is pushed to OFF. This indicates the traction control system is not operating. Push the traction control off switch again or restart the engine and the system will operate normally. See “Traction control system (TCS)” in the “Starting and driving” section of this manual. The traction control light also comes on when you turn the ignition key to the ON position. The light will turn off after about 2 seconds if the traction control system (TCS) is operational. If the light stays on or comes on along with the SLIP indicator light while you are driving, have the traction control system checked by a NISSAN dealer. While the traction control system is operating, you might feel slight vibration or hear the system working when starting the vehicle or accelerating, but this is normal. Turn signal/hazard indicator lights The appropriate light flashes when the turn signal switch is activated. Both lights flash when the hazard switch is turned on. Vehicle dynamic control off indicator light (if so equipped) This indicator light comes on when the vehicle dynamic control off switch is pushed to OFF. This indicates the vehicle dynamic control system is not operating. Push the vehicle dynamic control off switch again or restart the engine and the system will operate normally. See “Vehicle dynamic control (VDC) system” in the “Starting and driving” section of this manual. The vehicle dynamic control light also comes on when you turn the ignition key to the ON position. The light will turn off after about 2 seconds if the system is operational. If the light stays on or comes on along with the SLIP indicator light while you are driving, have the vehicle dynamic control system checked by a NISSAN dealer. Instruments and controls 2-11 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X SECURITY SYSTEM While the vehicle dynamic control system is operating, you might feel slight vibration or hear the system working when starting the vehicle or accelerating, but this is normal. AUDIBLE REMINDERS Brake pad wear warning The front disc brake pads have audible wear warnings. When a front brake pad requires replacement, it makes a high pitched scraping sound when the vehicle is in motion, whether or not the brake pedal is depressed. Have the brakes checked as soon as possible if the warning sound is heard. Key reminder chime A chime sounds if the driver’s door is opened while the key is left in the ignition switch. Remove the key and take it with you when leaving the vehicle. Light reminder chime With the ignition switch in the OFF position, a chime sounds when the driver’s door is opened if the headlights or parking lights are on. Turn the headlight control switch off before leaving the vehicle. NISSAN VEHICLE IMMOBILIZER SYSTEM (NVIS) The NISSAN Vehicle Immobilizer System (NVIS) will not allow the engine to start without the use of a registered NVIS key. If the engine fails to start using a registered NVIS key (for example, when interference is caused by another NVIS key, an automated toll road device or automatic payment device on the key ring), restart the engine using the following procedures: 1. Leave the ignition switch in the ON position for approximately 5 seconds. 2. Turn the ignition switch to the OFF or LOCK position, and wait approximately 5 seconds. 3. Repeat steps 1 and 2. 4. Restart the engine while holding the device (which may have caused the interference) separate from the registered NVIS key. Statement related to Section 15 of FCC Rules for NISSAN Vehicle Immobilizer System (CONT ASSY — IMMOBILIZER, ANT ASSY — IMMOBILIZER) This device complies with part 15 of the FCC Rules and RSS-210 of Industry Canada. Operation is subject to the following two conditions; (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation of the device. CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE MANUFACTURER FOR COMPLIANCE COULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT. If the no start condition re-occurs, NISSAN recommends placing the registered NVIS key on a separate key ring to avoid interference from other devices. 2-12 Instruments and controls Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X WINDSHIELD WIPER AND WASHER SWITCH NOTE: You can turn on or turn off the driving speed dependent intermittent wiper function. Refer to “Personalized settings menu” (vehicles without navigation system) or “Vehicle electronic systems” (vehicles with navigation system) in the “Display screen, heater, air conditioner and audio systems” section later in this manual. 2 s 3 s LIC0474 LIC0386 Security indicator light SWITCH OPERATION The security indicator light blinks whenever the ignition switch is in the LOCK, OFF or ACC position. This function indicates the NISSAN Vehicle Immobilizer System (NVIS) is operational. The windshield wiper and washer operates when the ignition switch is in the ON position. If the NVIS is malfunctioning, the light will remain on while the ignition key is in the ON position. If the light still remains on and/or the engine will not start, see a NISSAN dealer for NVIS service as soon as possible. Please bring all NVIS keys that you have when visiting your NISSAN dealer for service. Push the lever down to operate the wiper at the following speed: 1 s Intermittent — intermittent operation can be A adjusted by turning the knob toward s B (Faster). Also, the intermit(Slower) or s tent operation speed varies in accordance with the vehicle speed. (For example, when the vehicle speed is high, the intermittent operation speed will be faster.) Low — continuous low speed operation High — continuous high speed operation 4 to have one sweep operaPush the lever up s tion of the wiper. 5 to operate the Pull the lever toward you s washer. The wiper will also operate several times. WARNING In freezing temperatures the washer solution may freeze on the windshield and obscure your vision which may lead to an accident. Warm the windshield with the defroster before you wash the windshield. CAUTION ● Do not operate the washer continuously for more than 30 seconds. Instruments and controls 2-13 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X REAR WINDOW WIPER AND WASHER SWITCH ● Do not operate the washer if the reservoir tank is empty. WARNING In freezing temperatures the washer solution may freeze on the window and obscure your vision. Warm the rear window with the defroster before you wash the rear window. ● Do not fill the window washer reservoir tank with washer fluid concentrates at full strength. Some methyl alcohol based washer fluid concentrates may permanently stain the grille if spilled while filling the window washer reservoir tank. ● Pre-mix washer fluid concentrates with water to the manufacturer’s recommended levels before pouring the fluid into the window washer reservoir tank. Do not use the window washer reservoir tank to mix the washer fluid concentrate and water. CAUTION ● Do not operate the washer continuously for more than 30 seconds. ● Do not operate the washer if the reservoir tank is empty. LIC0468 The rear window wiper and washer operate when the ignition switch is in the ON position. Turn the switch clockwise from the OFF position to operate the wiper. 1 s Intermittent – intermittent operation (not adjustable) 2 s Low – continuous low speed operation 3 to operate the Push the switch forward s washer. The wiper will also operate several times. ● Do not fill the window washer reservoir tank with washer fluid concentrates at full strength. Some methyl alcohol based washer fluid concentrates may permanently stain the grille if spilled while filling the window washer reservoir tank. ● Pre-mix washer fluid concentrates with water to the manufacturer’s recommended levels before pouring the fluid into the window washer reservoir tank. Do not use the window washer reservoir tank to mix the washer fluid concentrate and water. 2-14 Instruments and controls Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X REAR WINDOW AND OUTSIDE MIRROR (if so equipped) DEFROSTER SWITCH HEADLIGHT AND TURN SIGNAL SWITCH LIC0487 Type A To defrost the rear window glass and outside mirrors (if so equipped), start the engine and turn the rear window defroster switch clockwise (Type A), or push the rear window defroster switch on (Type B). The rear window defroster indicator light on the display screen comes on. Turn (Type A) or push (Type B) the switch again to turn the defroster off. The rear window defroster automatically turns off after approximately 15 minutes. LIC0488 LIC0560 Type B Type A CAUTION When cleaning the inner side of the rear window, be careful not to scratch or damage the rear window defroster. HEADLIGHT CONTROL SWITCH Lighting 1 s When turning the switch to the position, the front parking, tail, license plate and instrument panel lights come on. 2 s When turning the switch to the position, the headlights come on and all the other lights remain on. Instruments and controls 2-15 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X LIC0687 Type B LIC0688 Type C LIC0515 Autolight system (if so equipped) 1 is located on top of the The autolight sensor s instrument panel. The autolight system allows the headlights to be set so they turn on and off automatically. The autolight system can: ● Turn on the headlights, front parking, tail, license plate and instrument panel lights automatically when it is dark. ● Turn off all the lights when it is light. ● Keep all the lights on for up to 180 seconds after you turn the key to OFF and all doors are closed. 2-16 Instruments and controls Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X NOTE: Autolight activation sensitivity and the time delay for autolight shutoff can be adjusted. See “Personalized settings menu” (vehicles without navigation system) or “Vehicle electronic systems” (vehicles with navigation system) in the “Display screen, heater, air conditioner and audio systems” section later in this manual. Be sure you do not put anything on top of the autolight sensor located on top of the instrument panel. The autolight sensor controls the autolight; if it is covered, the autolight sensor reacts as if it is dark out and the headlights will illuminate. If this occurs while parked with the engine off and the key in the ON position, your vehicle’s battery could become discharged. To turn on the autolight system: 1. Make sure the headlight switch is in the AUTO position. 2. Turn the ignition key to ON. 3. The autolight system automatically turns the headlights on and off. LIC0390 Headlight beam select 1 s To select the high beam function, push the lever forward. The high beam lights come on light illuminates. and the ● if all doors are closed, the headlights remain on for 45 seconds, then turn off. 2 s 3 s Pull the lever back to select the low beam. ● if another door is opened, then the 5 minute timer is reset. Battery saver system Initially, if the ignition switch is turned OFF and a door is opened and left open, the headlights remain on for 5 minutes. During that 5 minutes: To turn the autolight system off, turn the switch to the OFF, , or position. Pulling and releasing the lever flashes the headlight high beams on and off. If the ignition switch is turned OFF while the headlight switch is in the or position, the headlights will turn off after 5 minutes. Instruments and controls 2-17 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X After the headlights automatically turn off with the headlight switch in the or position, the headlights will illuminate again for 5 minutes if the headlight switch is moved to the OFF position and then turned to the or position. CAUTION ● Be sure to turn the light switch to the OFF position when you leave the vehicle for extended periods of time, otherwise the battery will go dead. ● Never leave the light switch on when the engine is not running for extended periods of time even if the headlights turn off automatically. DAYTIME RUNNING LIGHT SYSTEM (Canada only) The headlights automatically illuminate at a reduced intensity when the engine is started with the parking brake released. The daytime running lights operate with the headlight switch in the OFF position or in the position. Turn the headlight switch to the position for full illumination when driving at night. If the parking brake is applied before the engine is started, the daytime running lights do not illuminate. The daytime running lights illuminate when the parking brake is released. The daytime running lights will remain on until the ignition switch is turned off. WARNING When the daytime running light system is active, tail lights on your vehicle are not on. It is necessary at dusk to turn on your headlights. Failure to do so could cause an accident injuring yourself and others. LIC0392 INSTRUMENT BRIGHTNESS CONTROL The instrument cluster illuminates when the ignition switch is in ON position. The instrument brightness control operates when the headlight control switch is in the AUTO, or position. Turn the control to adjust the brightness of instrument panel lights when driving at night. The instrument brightness control will not adjust the brightness when the headlights or parking lights are off. 2-18 Instruments and controls Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X LIC0391 LIC0393 AIC0102 TURN SIGNAL SWITCH FOG LIGHT SWITCH (if so equipped) CORNERING LIGHT Turn signal To turn the fog lights on, turn the headlight switch to the position, then turn the fog light switch to the position. To turn them off, turn the fog light switch to the OFF position. The cornering light provides additional illumination toward the turning direction. The cornering light will illuminate on the turning direction side when a turn is signaled with the headlights on. 1 s Move the lever up or down to signal the turning direction. When the turn is completed, the turn signals cancel automatically. Lane change signal 2 s The headlights must be on for the fog lights to operate. To signal a lane change, move the lever up or down to the point where the indicator light begins to flash, but the lever does not latch. Instruments and controls 2-19 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X HAZARD WARNING FLASHER SWITCH HORN ● Turn signals do not work when the hazard warning flasher lights are on. The flashers will operate with the ignition switch in any position. Some state laws may prohibit the use of the hazard warning flasher switch while driving. LIC0394 LIC0395 Push the switch on to warn other drivers when you must stop or park under emergency conditions. All turn signal lights flash. To sound the horn, push the center pad area of the steering wheel. WARNING ● If stopping for an emergency, be sure to move the vehicle well off the road. ● Do not use the hazard warning flashers while moving on the highway unless unusual circumstances force you to drive so slowly that your vehicle might become a hazard to other traffic. WARNING Do not disassemble the horn. Doing so could affect proper operation of the supplemental front air bag system. Tampering with the supplemental front air bag system may result in serious personal injury. 2-20 Instruments and controls Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X HEATED SEAT (if so equipped) 3. When the seat is warmed or before you leave the vehicle, be sure to turn the switch off. ● The battery could run down if the seat heater is operated while the engine is not running. CAUTION ● Do not use the seat heater for extended periods or when no one is using the seat. ● Do not put anything on the seat which insulates heat, such as a blanket, cushion, seat cover, etc. Otherwise, the seat may become overheated. LIC0469 The front seats are warmed by built-in heaters (if so equipped). The switches are located at the sides of the seats. 1. Start the engine. 2. Push the (low) or (high) position of the switch, as desired, depending on the temperature. The indicator light in the switch will illuminate. The heater is controlled by a thermostat, automatically turning the heater on and off. The indicator light will remain on as long as the switch is on. ● Do not place anything hard or heavy on the seat or pierce it with a pin or similar object. This may result in damage to the heater. ● Any liquid spilled on the heated seat should be removed immediately with a dry cloth. ● When cleaning the seat, never use gasoline, benzine, thinner, or any similar materials. ● If any abnormalities are found or the heated seat does not operate, turn the switch off and have the system checked by your NISSAN dealer. Instruments and controls 2-21 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X TRACTION CONTROL SYSTEM (TCS) OFF SWITCH (if so equipped) VEHICLE DYNAMIC CONTROL (VDC) OFF SWITCH (if so equipped) LIC0451 WIC0534 The vehicle should be driven with the Traction Control System (TCS) on for most driving conditions. The vehicle should be driven with the Vehicle Dynamic Control (VDC) system on for most driving conditions. If the vehicle is stuck in mud or snow, the VDC system reduces the engine output to reduce wheel spin. The engine speed will be reduced even if the accelerator is depressed to the floor. If maximum engine power is needed to free a stuck vehicle, turn the VDC system off. To turn off the VDC system, push the VDC OFF switch. The indicator will come on. Push the VDC OFF switch again or restart the engine and the system will operate normally. See “Vehicle dynamic control (VDC) system” in the “Starting and driving” section. When the vehicle is stuck in mud or snow, the TCS reduces the engine output to reduce wheel spin. The engine speed will be reduced even if the accelerator is depressed to the floor. If maximum engine power is needed to free a stuck vehicle, turn the TCS off. To turn off the TCS, push the TCS OFF switch. The indicator will come on. Push the “TCS OFF” switch again or restart the engine and the system will operate normally. See “Traction control system (TCS)” in the “Starting and driving” section. REAR SONAR SYSTEM OFF SWITCH (if so equipped) LIC0471 WARNING The rear sonar system is a convenience but it is not a substitute for proper backing. Always turn and check that it is safe to do so before backing up. Always back up slowly. The rear sonar system (if so equipped) is active when the ignition is in the ON position and the shift selector lever is in R (Reverse). When sensors detect obstacles within 6 ft (1.8 m) of the rear bumper, a beeping tone is emitted. 2-22 Instruments and controls Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X POWER OUTLET The rear sonar system can be disabled by pushing the OFF switch. When the system is disabled, the indicator light on the switch will illuminate. The system will automatically reset the next time the ignition switch is turned on. See “Rear sonar system” in the “Starting and driving” section. LIC0486 Passenger compartment The power outlets are for powering electrical accessories such as cellular telephones. The power outlets located inside the center console storage bin and in the cargo area are powered directly by the vehicle’s battery. The power outlets located on the side of the center console and in the 2nd row are powered only when the ignition key is in the ACC or ON position. Open the cap to use a power outlet. LIC0485 Inside center console storage bin CAUTION ● The outlet and plug may be hot during or immediately after use. ● This power outlet is not designed for use with a cigarette lighter unit. ● Do not use with accessories that exceed a 12 volt, 120W (10A) power draw. Do not use double adapters or more than one electrical accessory. ● Use this power outlet with the engine running. (If the engine is stopped, this could result in a discharged battery.) Instruments and controls 2-23 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X ● When not in use, be sure to close the cap. Do not allow water to contact the outlet. LIC0516 2nd row LIC0517 Cargo area ● Avoid using when the air conditioner, headlights or rear window defroster is on. ● Before inserting or disconnecting a plug, be sure the electrical accessory being used is turned OFF. ● Push the plug in as far as it will go. If good contact is not made, the plug may overheat or the internal temperature fuse may blow. 2-24 Instruments and controls Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X STORAGE WARNING Keep storage bins closed while driving to help prevent injury in an accident or a sudden stop. LIC0498 NOTE HOLDER Insert a card or photograph into the note holder. WARNING Do not use note holder while driving so full attention may be given to vehicle operation. LIC0495 UPPER INSTRUMENT PANEL STORAGE COMPARTMENT Push the button to release the lid to the 1st open position. You can raise and hold the lid by hand to the 2nd open position for improved access to the compartment. Push the lid down to close. Instruments and controls 2-25 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X LIC0501 Driver’s side LOWER INSTRUMENT PANEL STORAGE TRAYS LIC0500 Passenger’s side LIC0518 PASSENGER SEAT STORAGE TRAY (if so equipped) Pull the tray to open it. WARNING Do not place sharp objects in the trays to help prevent injury in an accident or sudden stop. 2-26 Instruments and controls Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X WARNING The storage tray should not be used while driving so full attention may be given to vehicle operation. LIC0496 LIC0497 CENTER CONSOLE Lower storage bin Storage tray Open the lower storage bin by pressing the button down. The center console storage tray can be used to store a cellular telephone and other small items. A cord can be routed to the power outlet through the notch on the side of the tray or through the access hole on the bottom of the tray. (Remove the access hole cover first.) A coin holder is also located inside the tray. Push to close. Pull the tray open to the 1st or 2nd position. Push the tray to close. Instruments and controls 2-27 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X ● Do not leave sunglasses in the sunglasses holder while parking in direct sunlight. The heat may damage the sunglasses. LIC0499 LIC0508 GLOVE BOX SUNGLASSES HOLDER Open the glove box by pulling the handle. Use the 1 or unlocking s 2 the master key when locking s glove box. The valet key cannot be used to lock or unlock the glove box. To open the sunglasses holder, push and release. WARNING Keep glove box lid closed while driving to help prevent injury in an accident or a sudden stop. WARNING The sunglasses case should not be used while driving so full attention may be given to vehicle operation. CAUTION ● Do not use for anything other than sunglasses. 2-28 Instruments and controls Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X LIC0519 LIC0502 CONVENIENCE HOOK Use the convenience hook to store items such as a purse, hat or small trash bag. Front door LIC0520 Sliding door MAP POCKETS CAUTION Do not apply a total load of more than 10 lbs (4.5 kg) to the convenience hook. Instruments and controls 2-29 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X LIC0503 LIC0504 LIC0505 SEATBACK POCKETS GROCERY HOOKS UMBRELLA HOLDER The seatback pockets are located on the back of the driver and passenger seats. The pockets can be used to store maps. The grocery hooks allow for standard size plastic grocery bags to hang side by side. The net located on the back of the driver’s seat can be used to hold an umbrella. Slide the umbrella in and out of either end. CAUTION Do not apply a total load of more than 18 lbs (8 kg) to a single grocery hook. 2-30 Instruments and controls Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X LIC0513 OVERHEAD CONSOLE WARNING Keep storage bins closed while driving to help prevent injury in an accident or a sudden stop. LIC0512 Small storage bin Push the button to open the small storage bin. Push the lid up to close. Large storage bin Push the button to open the storage bin. Use the net to keep small items in place. Push the lid up to close. Instruments and controls 2-31 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X LIC0510 Front CUP HOLDERS To open the front cup holders, push the button. The lid springs open automatically. Push the lid to the full open position. To store another cup, fold down the second cup holder ring. To close, pull the entire cupholder unit up to the original position. LIC0509 2nd row WARNING The cup holder should not be used while driving so full attention may be given to vehicle operation. CAUTION ● Use only soft cups in the cup holder. Hard objects can injure you in an accident. CAUTION ● Avoid abrupt starting and braking when the cup holder is being used to prevent spilling the drink. If the liquid is hot, it can scald you or your passenger. 2-32 Instruments and controls Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X LIC0521 Sliding door bottle holder CAUTION LIC0507 3rd row LIC0506 3RD ROW ARMREST BIN Raise the lid to open the 3rd row armrest bin. Do not use bottle holder for any other objects that could be thrown about in the vehicle and possibly injure people during sudden braking or an accident. Instruments and controls 2-33 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X LIC0514 LIC0511 LIC0522 CARGO AREA STORAGE BIN GARMENT HOOK HEAD RESTRAINT STORAGE To open the cargo area storage bin, turn the knob 1 . The lid can be removed. counterclockwise s To store garments, pull the garment hook down to the use position. The storage bag can be used to store up to three head restraints or other items. To close, replace the lid and turn the knob clock2 . wise s CAUTION Do not apply a total load of more than 55 lbs (25 kg) to the hook. The bag can be retained on the universal fasteners located on the trim in the cargo area. CAUTION ● The cargo contained in the storage bag must not exceed 5 lbs (2.2 kg). ● Do not apply a total load of more than 55 lbs (25 kg) to the universal fasteners. 2-34 Instruments and controls Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X The front and rear cross bars (if so equipped) can be adjusted forward and backward by loosening 1 with the tool provided the TorxT head fastener s in the jack tool kit. Place your luggage on the bars, adjust the bars, and secure the luggage 2 on the bars. with rope to the utility loops s Always check the tightness of the crossbar TorxT head fasteners. WARNING Properly secure all cargo with ropes or straps to help prevent it from sliding or shifting. In a sudden stop or collision, unsecured cargo could cause personal injury. CAUTION Use care when placing or removing items from the roof rack. If you cannot comfortably lift the items onto the roof rack from the ground, use a ladder or stool. LIC0530 ROOF RACK (if so equipped) Always distribute the luggage evenly on the roof rack. Do not load more than 125 pounds (56 kg). Be careful that your vehicle does not exceed the Gross Vehicle Weight Rating (GVWR) or its Gross Axle Weight Rating (GAWR front and rear). The GVWR and GAWR are located on the Safety Compliance Certification Label (located on the driver’s door pillar). For more information regarding GVWR and GAWR, refer to “Technical and consumer information.” Instruments and controls 2-35 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X WINDOWS POWER WINDOWS seconds after the ignition switch is turned to the OFF position. If the driver’s or passenger’s door is opened during this period of about 45 seconds, power to the windows is canceled. To open a window, push the switch and hold it down. To close a window, pull the switch and hold it up. To stop the opening or closing function at any time, simply release the switch. WARNING ● Make sure that all passengers have their hands, etc. inside the vehicle while it is in motion and before closing the windows. Use the window lock switch to prevent unexpected use of the power windows. ● Do not leave children unattended inside the vehicle. They could unknowingly activate switches or controls and become trapped in a window. Unattended children could become involved in serious accidents. LIC0489 1. 2. 3. 4. 5. 6. Window lock button Door lock/unlock button Front passenger side automatic switch Right rear power vent window switch (if so equipped) Left rear power vent window switch (if so equipped) Driver side automatic switch Driver’s side power window switch The driver’s side control panel is equipped with switches to open or close all of the windows. The power windows operate when the ignition switch is in the ON position, or for about 45 2-36 Instruments and controls Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X Depending on the environment or driving conditions, the auto-reverse function may be activated if an impact or load similar to something being caught in the window occurs. WARNING There are some small distances immediately before the closed position which cannot be detected. Make sure that all passengers have their hands, etc., inside the vehicle before closing the window. LIC0490 LIC0410 Front passenger power window switch Automatic operation The passenger window switch operates only the corresponding passenger window. To open the 1 . To window, push the switch and hold it down s 2 . close the window, pull the switch up s To fully open a window equipped with automatic operation, press the window switch down (only driver’s side shown) to the second detent and release it; it need not be held. The window automatically opens all the way. To stop the window, lift the switch up while the window is opening. Locking passengers’ windows When the window lock button is depressed, only the driver side window can be opened or closed. Push it again to cancel the window lock function. If the control unit detects something caught in a window equipped with automatic operation as it is closing, the window will be immediately lowered. To fully close a window equipped with automatic operation, pull the switch up to the second detent and release it; it need not be held. Auto-reverse function The auto-reverse function can be activated when a window is closed by automatic operation. Instruments and controls 2-37 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X during this 45 second period, power to the vent windows is cancelled. LIC0523 LIC0524 POWER VENT WINDOWS (if so equipped) MANUAL VENT WINDOWS (if so equipped) Use the vent window switches on the driver’s side window controls to open and close the power vent windows. To open a manual vent window, pull the latch handle toward you until it releases. To open a power vent window, press the switch 1 . down s To close the window, lift the switch up s. 2 The power vent windows operate when the ignition key is in the ON position, or for 45 seconds after the ignition key is turned to the OFF position. If the driver’s or passenger’s door is opened To lock the window in the open position, push the latch handle rearward until it locks. To close a manual vent window, pull the latch handle toward you and push the rear portion of the latch toward the rear of the vehicle until it locks. 2-38 Instruments and controls Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X SKYVIEW™ ROOF (if so equipped) SUNROOF (if so equipped) To close the sunroof, slide the switch to the CLOSE position. The position of the sliding sunroof lid can be chosen by the position of the sliding switch. To fully open or close the sunroof, completely move the switch to the open or closed position. Tilting the sunroof To tilt the sunroof up, push the tilt switch to the UP position. When the roof is open, it will automatically close and then tilt up. To tilt the sunroof down, push the tilt switch to the DOWN position. LIC0525 To close the skyview roof shade, pull the tab to draw out the shade. Lock the shade in place by positioning the rod on the holder. To open the shade, lift the rod from the holder and ease the shade back into its stored position. CAUTION Do not pull the skyroof sun shade straight down. This can damage the shade. LIC0473 AUTOMATIC SUNROOF The sunroof will only operate when the ignition key is in the ON position. The automatic sunroof is operational for about 45 seconds, even if the ignition key is turned to the ACC or OFF position. If the driver’s door or the front passenger’s door is opened during this period of about 45 seconds, power to the sunroof is canceled. Sliding the sunroof To open the sunroof, slide the switch to the OPEN position. When the sunroof is tilted up, it will automatically tilt down and then open. Restarting the sunroof sliding switch The sliding switch will become inoperable after the battery terminal is disconnected, the electrical supply interrupted and/or some abnormality detected. Use the following reset procedure to return sunroof operation to normal. 1. If the sunroof lid is open, push the tilting switch repeatedly toward DOWN to fully close the lid. 2. Finally, push and hold the tilting switch for more than 2 seconds toward DOWN to reestablish the lid’s home position. The sunroof should now operate normally. Instruments and controls 2-39 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X Auto reverse function (when closing or tilting down the sunroof) The auto reverse function can be activated when the sunroof is closed or tilted down by automatic operation when the ignition key is in the ON position or for about 45 seconds after the ignition key is turned to the OFF position. Depending on the environment or driving conditions, the auto reverse function may be activated if an impact or load similar to something being caught in the sunroof occurs. WARNING There are some small distances immediately before the closed position which cannot be detected. Make sure that all passengers have their hands, etc., inside the vehicle before closing the sunroof. If the auto reverse function malfunctions and repeats opening or tilting up the sunroof, keep pushing the tilt down switch within 5 seconds after it happens, then the sunroof will fully close gradually. In this case, make sure nothing is caught in the sunroof. WARNING ● Do not allow anyone to stand up or extend any portion of their body out of the sunroof opening while the vehicle is in motion or while the sunroof is closing. CAUTION When closing: If the control unit detects something caught in the sunroof as it moves to the front, the sunroof will immediately open backward. ● Do not place heavy objects on the sunroof or surrounding area. If the control unit detects something caught in the sunroof as it tilts down, the sunroof will immediately tilt up. Have your NISSAN dealer check and repair the sunroof. ● In an accident you could be thrown from the vehicle through an open sunroof. Always use seat belts and child restraints. ● Remove water drops, snow, ice or sand from the sunroof before opening. When tilting down: If the sunroof does not close Sun shade Open and close the sun shade by sliding it forward or backward. 2-40 Instruments and controls Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X LIGHTS ON DEMAND SWITCH If the lights on demand switch is in the position, the lights will stay on for about 30 seconds when: ● The doors are unlocked by the keyfob, a key or the power door lock switch while all doors are closed and the ignition switch is in the OFF position. ● The driver’s door is opened and then closed while the key is removed from the ignition switch. NOTE: The foot well and door step lights illuminate when the driver and passenger doors are open regardless of the lights on demand switch position. These lights will turn off automatically after 30 minutes while doors are open to prevent the battery from becoming discharged. ● The key is removed from the ignition switch while all doors are closed. LIC0472 The lights on demand switch allows the driver to select one of three lighting modes for the room lights. The room lights are the map lights, personal lights and puddle lamps (if so equipped). The lights on demand switch operates regardless of ignition switch position. : The room lights illuminate. The lights will turn off automatically after 30 minutes to prevent the battery from becoming discharged. The room lights will turn off while the 30 second timer is activated when: ● The driver’s door is locked by the keyfob, a key, or the power door lock switch. ● The ignition switch is turned ON. The lights will turn off automatically after 30 minutes while doors are open to prevent the battery from becoming discharged. OFF: The room lights do not illuminate. : The room lights illuminate when a door is opened. Instruments and controls 2-41 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X PERSONAL LIGHTS LIC0492 Type A The rear seating positions have personal lights located on the headliner or on the overhead console. There is also a light above the cargo area on the overhead trim. To operate a personal light located on the headliner (Type A), push the light. LIC0493 Type B The personal lights on the overhead console (Type B) can be swiveled 360 degrees. To turn on the light, press the button. Press the button again to turn off the light. LIC0492 Type C The cargo light on the overhead trim (Type C) has a three-position switch. To operate, push the light. On: The light is illuminated Normal: The light illuminates when any door is opened or unlocked by the keyfob. The light turns off after 30 seconds or when all doors are closed. Off: The light does not illluminate, regardless of door position or lock status. 2-42 Instruments and controls Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X MAP LIGHTS HOMELINKT UNIVERSAL TRANSCEIVER (if so equipped) The HomeLinkT Universal Transceiver provides a convenient way to consolidate the functions of up to three individual hand-held transmitters into one built-in device. HomeLinkT Universal Transceiver: ● Will operate most Radio Frequency (RF) devices such as garage doors, gates, home and office lighting, entry door locks and security systems. LIC0491 To turn the map lights on, press the switches. To turn them off, press the switches again. CAUTION Do not use for extended periods of time with the engine stopped. This could result in a discharged battery. ● Is powered by your vehicle’s battery. No separate batteries are required. If the vehicle’s battery is discharged or is disconnected, HomeLinkT will retain all programming. Once the HomeLinkT Universal Transceiver is programmed, retain the original transmitter for future programming procedures (i.e., new vehicle purchases). Upon sale of the vehicle, the programmed HomeLinkT Universal Transceiver buttons should be erased for security purposes. For additional information refer to “Programming HomeLinkT” later in this section. WARNING ● Do not use the HomeLinkT Universal Transceiver with any garage door opener that lacks safety stop and reverse features as required by federal safety standards. (These standards became effective for opener models manufactured after April 1, 1982). A garage door opener which cannot detect an object in the path of a closing garage door and then automatically stop and reverse, does not meet current federal safety standards. Using a garage door opener without these features increases the risk of serious injury or death. ● During the programming procedure your garage door or security gate will open and close (if the transmitter is within range). Make sure that people or objects are clear of the garage door, gate, etc. that you are programming. ● Your vehicle’s engine should be turned off while programming the HomeLinkT Universal Transceiver. Instruments and controls 2-43 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X 4. Hold down both buttons until the indicator light on the HomeLinkT flashes, changing from a “slow blink” to a “rapidly flashing blink”. This could take up to 90 seconds. When the indicator light flashes rapidly, both buttons may be released. The rapidly flashing light indicates successful programming. To activate the garage door or other programmed device, press and hold the programmed HomeLinkT button — releasing when the device begins to activate. LIC0526 PROGRAMMING HOMELINKT 1. To begin, press and hold the two outer HomeLinkT buttons (to clear the memory) 1 blinks slowly (after until the indicator light s 20 seconds). Release both buttons. 2. Position the end of the hand-held transmitter 1 - 3 inches (26 - 76 mm) away from the HomeLinkT surface. LIC0527 3. Using both hands, simultaneously press and hold both the HomeLinkT button you want to program and the hand-held transmitter button. DO NOT release the buttons until step 4 has been completed. 5. If the indicator light on the HomeLinkT blinks rapidly for 2 seconds and then turns solid, HomeLinkT has picked up a “rolling code” garage door opener signal. You will need to proceed with the next steps to train the HomeLinkT to complete the programming which may require a ladder and another person for convenience. 6. Press and release the “smart” or “learn” program button located on the garage door opener’s motor to activate the “training mode”. This button is usually located near the antenna wire that hangs down from the motor. If the wire originates from under a light lens, you will need to remove the lens to access the program button. 2-44 Instruments and controls Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X NOTE: Once you have pressed and released the program button on the garage door opener’s motor and the “training light” is lit, you have 30 seconds in which to perform step 7. Use the help of a second person for convenience to assist when performing this step. 7. Within 30 seconds of pressing and releasing the garage door opener program button, quickly and firmly press and release the HomeLinkT button you’ve just programmed. Press and release the HomeLinkT button up to 3 times to complete the training. 8. Your HomeLinkT button should now be programmed. (To program the remaining HomeLinkT buttons for additional door or gate openers, follow steps 2-8 only.) NOTE: Do not repeat step 1 unless you want to “clear” all previously programmed HomeLinkT buttons. If you have any questions or are having difficulty programming your HomeLinkT buttons, please refer to the HomeLinkT web site at: www.homelink.com or call 1-800-NISSAN-1 (1800-647-7261). PROGRAMMING HOMELINKT FOR CANADIAN CUSTOMERS PROGRAMMING TROUBLEDIAGNOSIS Prior to 1992, D.O.C. regulations required handheld transmitters to stop transmitting after 2 seconds. To program your hand-held transmitter to HomeLinkT, continue to press and hold the HomeLinkT button (note steps 2 - 4 under “Programming HomeLinkT”) while you press and repress (“cycle”) your hand-held transmitters every 2 seconds until the indicator light flashes rapidly (indicating successful programming). If the HomeLinkT does not quickly learn the handheld transmitter information: NOTE: When programming a garage door opener, etc., it is advised to unplug the device during the “cycling” process to prevent possible damage to the garage door opener components. OPERATING THE HOMELINKT UNIVERSAL TRANSCEIVER The HomeLinkT Universal Transceiver (once programmed) may now be used to activate the garage door, etc. To operate, simply press the appropriate programmed HomeLinkT Universal Transceiver button. The red indicator light will illuminate while the signal is being transmitted. ● replace the hand-held transmitter batteries with new batteries. ● position the hand-held transmitter with its battery area facing away from the HomeLinkT surface. ● press and hold both the HomeLinkT and hand-held transmitter buttons without interruption. ● position the hand-held transmitter 1 - 3 inches (26 - 76 mm) away from the HomeLinkT surface. Hold the transmitter in that position for up to 15 seconds. If HomeLinkT is not programmed within that time, try holding the transmitter in another position – keeping the indicator light in view at all times. If you continue to have programming difficulties, please contact the NISSAN Consumer Affairs Department. The phone numbers are located in the Foreword of this manual. Instruments and controls 2-45 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X CLEARING THE PROGRAMMED INFORMATION Individual buttons cannot be cleared. However, to clear all programming, press and hold the two outside buttons and release when the indicator light begins to flash (approximately 20 seconds). REPROGRAMMING A SINGLE HOMELINKT BUTTON To reprogram a HomeLinkT Universal Transceiver button, complete the following. 1. Press and hold the desired HomeLinkT button. Do not release the button until step 4 has been completed. 2. When the indicator light begins to flash slowly (after 20 seconds), position the hand-held transmitter 1 - 3 inches (26 - 76 mm) away from the HomeLinkT surface. 3. Press and hold the hand-held transmitter button. 4. The HomeLinkT indicator light will flash, first slowly and then rapidly. When the indicator light begins to flash rapidly, release both buttons. The HomeLinkT Universal Transceiver button has now been reprogrammed. The new device can be activated by pushing the HomeLinkT button that was just programmed. This procedure will not affect any other programmed HomeLinkT buttons. This transmitter has been tested and complies with FCC and DOC/MDC rules. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the device. IF YOUR VEHICLE IS STOLEN DOC: ISTC 1763K1313 If your vehicle is stolen, you should change the codes of any non-rolling code device that has been programmed into HomeLinkT. Consult the Owner’s Manual of each device or call the manufacturer or dealer of those devices for additional information. FCC I.D. CV2V67690 When your vehicle is recovered, you will need to reprogram the HomeLinkT Universal Transceiver with your new transmitter information. FCC Notice: This device complies with FCC rules part 15. Operation is subject to the following two conditions: (1) This device may not cause harmful interference and (2) This device must accept any interference that may be received, including interference that may cause undesired operation. 2-46 Instruments and controls Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X 3 Pre-driving checks and adjustments Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2 Nissan vehicle immobilizer system (NVIS) keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2 Doors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3 Locking with key. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3 Locking with inside lock knob . . . . . . . . . . . . . . . . . . . . 3-4 Locking with power door lock switch . . . . . . . . . . . . . 3-5 Operating the manual sliding door (if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5 Using the main ON/OFF switch for the power sliding door. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6 Operating the power sliding door (if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-7 Child safety sliding door lock . . . . . . . . . . . . . . . . . . . . 3-9 Remote keyless entry system . . . . . . . . . . . . . . . . . . . . . . . 3-9 How to use remote keyless entry system . . . . . . . . . 3-10 Battery replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-13 Hood . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-14 Back door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-15 Operating the manual back door . . . . . . . . . . . . . . . . 3-15 Using the main ON/OFF switch for the power back door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-16 Operating the power back door (if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-16 Back door release . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-18 Fuel filler lid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-20 Opener operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-20 Fuel filler cap. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-20 Steering wheel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-21 Tilt operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-21 Pedal position adjustment (if so equipped) . . . . . . . . . . 3-22 Sun visors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-22 Vanity mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-23 Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-23 Inside mirror (if so equipped). . . . . . . . . . . . . . . . . . . . 3-23 Automatic anti-glare inside mirror (if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-23 Outside mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-24 Automatic drive positioner (if so equipped) . . . . . . . . . . 3-25 Memory storage function . . . . . . . . . . . . . . . . . . . . . . . 3-26 Entry/exit function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-27 System operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-28 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X KEYS A key number is only necessary when you have lost all keys and do not have one to duplicate from. If you still have a key, your NISSAN dealer can duplicate it. NISSAN VEHICLE IMMOBILIZER SYSTEM (NVIS) KEYS You can only drive your vehicle using the master or valet keys which are registered to the NISSAN Vehicle Immobilizer System components in your vehicle. These keys have a transponder chip in the key head. WPD0128 1. 2. 3. 4. Two master keys (black) with transponder chip and chrome NISSAN brand symbol on one side Valet key (black) with transponder chip Key number plate Transponder chip A key number plate is supplied with your keys. Record the key number and keep it in a safe place (such as your wallet), not in the vehicle. If you lose your keys, see a NISSAN dealer for duplicates by using the key number. NISSAN does not record key numbers so it is very important to keep track of your key number plate. previously registered into the NISSAN Vehicle Immobilizer System. After the registration process, these components will only recognize keys coded into the NISSAN Vehicle Immobilizer System (NVIS) during registration. Any key that is not given to your dealer at the time of registration will no longer be able to start your vehicle. Do not allow the immobilizer system key, which contains an electrical transponder, to come into contact with salt water. This could affect system function. The master key can be used for all the locks. The valet key cannot be used for the glove box lock. To protect belongings when you leave a key with someone, give them the valet key only. Never leave these keys in the vehicle. Additional or replacement keys: If you still have a key, the key number is not necessary when you need extra NISSAN Vehicle Immobilizer System keys. Your dealer can duplicate your existing key. As many as five NVIS keys can be used with one vehicle. You should bring all NVIS keys that you have to your NISSAN dealer for registration. This is because the registration process will erase the memory of all key codes 3-2 Pre-driving checks and adjustments Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X DOORS WARNING ● Always have the doors locked while driving. Along with the use of seat belts, this provides greater safety in the event of an accident by helping to prevent persons from being thrown from the vehicle. This also helps keep children and others from unintentionally opening the doors, and will help keep out intruders. ● When opening a sliding door on a slope, ensure that it is fully open and that it does not close by itself. ● Before opening any door, always look for and avoid oncoming traffic. ● Do not leave children unattended inside the vehicle. They could unknowingly activate switches or controls. Unattended children could become involved in serious accidents. CAUTION ● Always use the door handle to open or close a sliding door. Do not attempt to open or close the doors by merely placing your hand on the door edge or door slide roller, as this may cause injury. ● Always be sure that hands and feet are clear of the door frame to avoid injury while closing a sliding door. LPD0181 Driver’s side LOCKING WITH KEY The power door lock system allows you to lock or unlock all doors at the same time. 1 of the vehicle Turning the key toward the front s locks all doors. 2 of the Turning the key one time toward the rear s vehicle unlocks that door. From that position, 3 (where the key can returning the key to neutral s only be removed and inserted) and turning it toward the rear again within 5 seconds unlocks 4 . all doors s Pre-driving checks and adjustments 3-3 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X Opening and closing windows The driver’s door key operation allows you to open and close windows equipped with automatic operation at the same time. ● To open the windows, turn the driver’s door key toward the rear of the vehicle for longer than 1 second after the door is unlocked. ● To close the windows, turn the driver’s door key to the front of the vehicle for longer than 1 second after the door is locked. Windows stop when the key cylinder is released. LPD0208 Inside lock for front doors LPD0224 Inside lock for sliding doors LOCKING WITH INSIDE LOCK KNOB To lock the door without the key, move the inside 1 , then close the lock knob to the lock position s door. To unlock the door without the key, move the 2 . inside lock knob to the unlock position s 3-4 Pre-driving checks and adjustments Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X key in the ignition and any door open, all doors will lock and unlock automatically. This helps to prevent the keys from being accidently locked inside the vehicle. LPD0183 Door lock switch LOCKING WITH POWER DOOR LOCK SWITCH To lock all the doors without a key, push the door lock switch (driver or front passenger side), to the 1 . When locking the door this way, lock position s be certain not to leave the key inside the vehicle. To unlock all the doors without a key, push the door lock switch (driver or front passenger side) 2 . to the unlock position s Lockout protection When the power door lock switch (driver or front passenger) is moved to the lock position with the LPD0233 OPERATING THE MANUAL SLIDING DOOR (if so equipped) WARNING Make sure that all passengers have their hands, etc. inside the vehicle before closing the sliding doors. The manual sliding door can be opened from the inside or the outside. To open a sliding door from the inside, push the 1 and pull the handle toward the rear of button s the vehicle. Pre-driving checks and adjustments 3-5 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X To open a sliding door from the outside, pull out the outside handle. When the switch is in the OFF position, the sliding door can still be opened with the keyfob or overhead console switch. The sliding door can also be opened manually with the inside or outside handle. The driver side sliding door cannot be opened fully when the fuel lid door is open. NOTE: If the child safety lock is in the lock position, the door pillar switch will not operate the sliding door regardless of the main ON/OFF switch position. LPD0222 USING THE MAIN ON/OFF SWITCH FOR THE POWER SLIDING DOOR The main ON/OFF switch is located in the overhead console. Push the switch ON to enable the door pillar switches and the power assist feature. An indicator light will illuminate when the switch is in the ON position. Push the switch OFF to disable the door pillar switches and the power assist feature. An indicator light will illuminate when the switch is in the OFF position. 3-6 Pre-driving checks and adjustments Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X Power Open: The door automatically moves from the fully closed position to the fully open position in approximately 4 seconds. The power open feature can be activated by the switches on the keyfob, the overhead console and the door pillar. ● A sliding door can be opened by the overhead console switch and the keyfob even if the vehicle is locked. The door will individually unlock and open. When the sliding door is closed, it will remain unlocked. The vehicle must be re-locked to lock the door. LPD0225 LPD0226 Door pillar switch OPERATING THE POWER SLIDING DOOR (if so equipped) WARNING ● Make sure that all passengers have their hands, etc. inside the vehicle before closing the sliding doors. ● Do not leave children unattended inside the vehicle. They could unknowingly activate switches or controls. Unattended children could become involved in serious accidents. Overhead console switch NOTE: To open, close or reverse a power sliding door, the shift selector lever must be in P (Park). Also, the power sliding doors will not operate if battery voltage is low. Power Assist: If the main on/off switch is ON and a sliding door is unlocked and manually moved toward the open or close position using the inside or outside handle, the power assist feature will be activated and the door will complete its motion automatically. ● The keyfob button must be held for 0.5 second before the door opens. ● The switch on the door pillar can only be used to open the door if the main ON/OFF switch is ON, the door is unlocked and the child lockout switch is not set. A warning chime will sound if the shift selector lever is moved out of P (Park) during a power open operation. The driver’s side power sliding door cannot be power opened when the fuel lid door is open. A warning chime will sound if an open operation is attempted. The door can be opened manually part way. Pre-driving checks and adjustments 3-7 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X Power Close: The door automatically moves from the fully open position to the secondary position. When the sliding door reaches the secondary position, the cinching motor engages and pulls the door to its primary latch position. Power close takes approximately 5 seconds. The power close feature can be activated by the switches on the keyfob, the overhead console and the door pillar. ● If the inside or outside handle is activated while the cinching motor is engaged, the cinching motor will disengage and release the latch. ● The keyfob button must be held for 0.5 second before the door closes. ● The switch on the door pillar can only be used to close the door if the main ON/OFF switch is ON. Reverse: The door will reverse direction immediately during power open or power close if the keyfob, overhead console or door pillar switch is pressed. A chime will sound to announce the reversal. Auto Reverse: If an obstacle is detected during power open or power close, a warning chime will sound and the door will reverse direction and return to the full open or full close position. If a second obstacle is detected, the door motion will stop and the clutch mode will be engaged. WARNING There are some small distances immediately before the closed position which cannot be detected. Make sure that all passengers have their hands, etc., inside the vehicle before closing the door. Clutch Mode: To help prevent unexpected slams due to gravity, the clutch mode is engaged intermittently for up to 6 seconds when power open or close is interrupted due to multiple obstacles, low battery voltage or the main ON/OFF switch turned to OFF. The door must then be opened or closed manually. Restarting the power sliding door Some power sliding door functions will become disabled after the battery terminal is disconnected and/or the electrical supply is interrupted. 2. If the power sliding door is open, press and hold the power sliding door switch on the overhead console until the door closes. 3. Release the switch. 4. Press and hold the power sliding door switch on the overhead console until the door opens as far as it can. 5. Release the switch. 6. Press and hold the power sliding door switch on the overhead console until the door closes. 7. Release the switch. The power sliding door should now work properly. NOTE: The restarting procedure must be completed for both the left-hand and righthand power sliding doors (if so equipped). The following procedure must be used to restart the power sliding door so that all functions are enabled. 1. Turn the main on/off switch to ON. 3-8 Pre-driving checks and adjustments Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X REMOTE KEYLESS ENTRY SYSTEM It is possible to lock/unlock all doors, turn on the interior lights and puddle lamps (if so equipped), and activate the panic alarm by using the keyfob from outside the vehicle. Some settings for the keyfob, such as horn beep and unlock driver’s door 1st, can be adjusted. Refer to “Personalized settings menu” (vehicles without navigation) or “Vehicle electronic systems” (vehicles with navigation system) in the “Display screen, heater, air conditioner and audio systems” section later in this manual. Be sure to remove the key from the vehicle before locking the doors. The keyfob can operate at a distance of approximately 33 ft (10 m) from the vehicle. The effective distance depends upon the conditions around the vehicle. As many as 5 keyfobs can be used with one vehicle. For information concerning the purchase and use of additional keyfobs, contact a NISSAN dealer. LPD0231 CHILD SAFETY SLIDING DOOR LOCK The child safety lock levers are located on the edge of the sliding doors. The child safety lock helps prevent the sliding door from being opened accidentally, especially when small children are in the vehicle. When the lever is in the lock position, the door can be opened only from the outside, by the overhead console switch or using the keyfob. The keyfob will not function when: ● the battery is discharged ● the distance between the vehicle and the keyfob is over 33 ft (10 m) The panic alarm will not activate when the key is in the ignition switch. Pre-driving checks and adjustments 3-9 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X twice and the horn beeps once as a reminder that the doors are already locked. CAUTION Listed below are conditions or occurrences which will damage the keyfob: ● If a door is open and you push the button, the doors will lock but the horn will not beep and the hazard warning lights will not flash. ● Do not allow the keyfob to become wet. ● Do not drop the keyfob. The horn may or may not beep. Refer to “Personalized settings menu” (vehicles without navigation system) or “Vehicle electronic systems” (vehicles with navigation system) in the “Display screen, heater, air conditioner and audio systems” section later in this manual. ● Do not strike the keyfob sharply against another object. ● Do not place the keyfob for an extended period in an area where temperatures exceed 140°F (60°C). If a keyfob is lost or stolen, NISSAN recommends erasing the ID code of that keyfob. This will prevent the keyfob from unauthorized use to unlock the vehicle. For information regarding the erasing procedure, please contact a NISSAN dealer. LPD0209 HOW TO USE REMOTE KEYLESS ENTRY SYSTEM Locking doors 1. Close all windows 2. Remove the key from the ignition switch. 3. Close the hood and all doors. 4. Push the button on the keyfob. All the doors lock. The hazard warning lights flash twice and the horn beeps once to indicate all doors are locked. ● When the button is pushed with all doors locked, the hazard warning lights flash 3-10 Pre-driving checks and adjustments Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X Push the 5 seconds. button on the keyfob again within ● All doors unlock. ● The hazard indicator flashes once if all doors are completely closed. The interior lights and puddle lamps (if so equipped) can be turned off without waiting 30 seconds by inserting the key into the ignition and turning to the ON or START position, locking the doors with the keyfob or pushing the interior light switch to the OFF position. Auto relock LPD0210 Unlocking doors Push the button on the keyfob once. ● Only the driver’s door unlocks. ● The hazard indicator flashes once if all doors are completely closed with the ignition key in any position except the ON position. ● The interior lights and puddle lamps (if so equipped) turn on and the light timer activates for 30 seconds when the lights on demand switch is in the position with the ignition key in any position except the ON position. When the button on the keyfob is pushed, all doors will lock automatically within 1 minute unless one of the following operations is performed: ● Any door is opened. ● A key is inserted into the ignition switch and the key is turned from OFF to ON. Opening windows The keyfob allows you to open windows equipped with automatic operation simultaneously. ● To open the windows, press the button on the keyfob for longer than 3 seconds after all doors are unlocked. The door windows will open while pressing the button on the keyfob. This opening windows function of the keyfob can be suspended using a CONSULT-II diagnostic tool. Please contact a NISSAN dealer. The door windows cannot be closed by using the keyfob. Linking the keyfob to automatic drive positioner memory If the vehicle is equipped with automatic drive positioner, the keyfob can be linked to a memory setting. See “Automatic driver positioner” later in this section. Pre-driving checks and adjustments 3-11 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X LPD0212 LPD0213 Operating the power sliding door (if so equipped) Operating the power back door (if so equipped) Push and hold the button on the keyfob for about 0.5 second to open or close the power sliding door. Push and hold the button on the keyfob for about 0.5 second to open or close the back door. The hazard warning lights flash and a chime sounds to indicate the power open or power close sequence has started. The door will reverse direction immediately during power open or power close if the keyfob button is pressed. A chime will sound to announce the reversal. For more information, see “Operating the power sliding door” earlier in this section. The door will reverse direction immediately during power open or power close if the keyfob button is pressed. A chime will sound to announce the reversal. For more information, see “Back door” later in this section. LPD0211 Using the panic alarm If you are near your vehicle and feel threatened, you may activate the panic alarm to call attention button on the by pushing and holding the keyfob for longer than 0.5 second. The panic alarm and headlights will stay on for 25 seconds. The panic alarm stops when: ● it has run for 25 seconds, or ● any button is pushed on the keyfob. 3-12 Pre-driving checks and adjustments Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X Using the interior lights Push the button on the keyfob once to turn on the interior lights and puddle lamps (if so equipped). The interior lights and puddle lamps (if so equipped) can be turned off without waiting 30 seconds by inserting the key into the ignition, locking the doors with the keyfob or pushing the interior light button to OFF. LPD0214 BATTERY REPLACEMENT Replace the battery in the keyfob as follows: 1 s 2 s s 3 Install a new battery with the “+” facing down. Open the lid using a coin. Recommended battery: Sanyo CR2025 or equivalent. Remove the battery. 4 s Close the lid securely. Pre-driving checks and adjustments 3-13 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X HOOD 5. Press the LOCK button, then the UNLOCK button two or three times to check the keyfob operation. If the battery is removed for any reason other than replacement, perform step 5. ● An improperly disposed battery can hurt the environment. Always confirm local regulations for battery disposal. ● The keyfob is water-resistant; however, if it does get wet, immediately wipe completely dry. ● The operational range of the keyfob extends to approximately 33 ft (10 m) from the vehicle. This range may vary with conditions. FCC Notice: Changes or modifications not expressly approved by the manufacturer for compliance could void the user’s authority to operate the equipment. LPD0215 s 1 Pull the hood lock release handle located below the driver side instrument panel. The hood will spring up slightly. 2 s Push the lever at the front of the hood to the side as illustrated with your fingertips and raise the hood. This device complies with Part 15 of the FCC Rules and RSS-210 of Industry Canada. 3 s Insert the support rod into the slot on the underside of the hood. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation of the device. When closing the hood, lower it slowly and make sure it locks into place. WARNING ● Make sure the hood is completely closed and latched before driving. Failure to do so could cause the hood to fly open and result in an accident. ● If you see steam or smoke coming from the engine compartment, to avoid injury do not open the hood. 3-14 Pre-driving checks and adjustments Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X BACK DOOR To close, lower and push the back door down securely. WARNING ● Always be sure the back door has been closed securely to prevent it from opening while driving. ● Do not drive with the back door open. This could allow dangerous exhaust gases to be drawn into the vehicle. See “Exhaust gas” in the “Starting and driving” section of this manual. LPD0221 OPERATING THE MANUAL BACK DOOR WARNING Make sure that all passengers have their hands, etc. inside the vehicle before closing the back door. The power door lock system allows you to lock or unlock all doors including the back door simultaneously. To open the back door, depress the opener handle and lift up. Pre-driving checks and adjustments 3-15 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X When the switch is in the OFF position, the rear door can still be opened with the keyfob or overhead console switch. The rear door can also be opened manually with the outside handle if the door is unlocked. LPD0229 LPD0222 USING THE MAIN ON/OFF SWITCH FOR THE POWER BACK DOOR The main ON/OFF switch is located in the overhead console. Rear pillar switch OPERATING THE POWER BACK DOOR (if so equipped) WARNING Push the switch ON to enable the rear pillar switch. An indicator light will illuminate when the switch is in the ON position. ● Make sure that all passengers have their hands, etc. inside the vehicle before closing the back door. Push the switch OFF to disable the rear pillar switch. An indicator light will illuminate when the switch is in the OFF position. Pushing the switch OFF while the door is opening or closing will cancel the operation and the door will go to manual mode. ● Do not leave children unattended inside the vehicle. They could unknowingly activate switches or controls. Unattended children could become involved in serious accidents. 3-16 Pre-driving checks and adjustments Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X and a chime sounds to indicate the power open sequence has been started. ● The back door can be opened by the overhead console switch and the keyfob even if the vehicle is locked. The door will individually unlock and open. Once the back door is closed, its lock will align to the vehicle’s lock or unlock status. ● The keyfob button must be held for 0.5 second before the door opens. ● The back door must be unlocked to open it with the outside opener handle. LPD0223 Overhead console switch NOTE: To open, close or reverse the power back door, the shift selector lever must be in P (Park). Also, the power back door will not operate if battery voltage is low. Power Open: The power back door automatically moves from the fully closed position to the fully open position in approximately 6 seconds. The power open feature can be activated by the switch on the keyfob and the overhead console and by the outside opener handle. The hazard lights flash ● The switch on the rear pillar cannot be used to open the back door. A warning chime will sound if the shift selector lever is moved out of P (Park) during a power open operation. Power Close: The power back door automatically moves from the fully open position to the secondary position. When the door reaches the secondary position, the cinching motor engages and pulls the door to its primary latch position. Power close takes approximately 8 seconds. The power close feature can be activated by the switch on the keyfob, the overhead console and the rear pillar. The hazard lights flash and a chime sounds to indicate the power close sequence has been started. ● If the outside opener handle is activated while the cinching motor is engaged, the cinching motor will disengage and release the latch. ● The keyfob button must be held for 0.5 second before the door closes. ● The switch on the rear pillar can only be used to close the back door if the main ON/OFF switch is ON. Reverse: The power back door will reverse direction immediately during power open or power close if the keyfob, overhead console or rear pillar switch is pressed. A chime will sound to announce the reversal. Auto Reverse: If an obstacle is detected during power open or power close, a warning chime will sound and the door will reverse direction and return to the full open or full close position. If a second obstacle is detected, the door motion will stop and the drive motor will disengage. The back door will enter manual mode. A pinch strip is mounted on each side of the back door. If an obstacle is detected by a pinch strip during power close, the door will reverse direction and return to the full open position. Pre-driving checks and adjustments 3-17 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X NOTE: CAUTION If the pinch strip is damaged or removed, the power close function will not operate. ● If the power back door does not stay open or if the door unexpectedly closes at any time while a continuous warning chime sounds, do not operate the back door. There may be a pressure loss in one or both of the back door gas stays. Have the back door inspected by a NISSAN dealer. WARNING There are some small distances immediately before the closed position which cannot be detected. Make sure that all passengers have their hands, etc., inside the vehicle before closing the door. Manual Mode: If power operation is not available, the back door may be operated manually. Power operation may not be available if the main ON/OFF switch is in the OFF position, if multiple obstacles have been detected in a single power cycle, or if battery voltage is low. LPD0238 Safe Mode: 1 lose pressure, the If the back door gas stays s power back door safe mode is activated. When the safe mode is activated, the back door slowly closes. A continuous warning chime sounds until the door is in the fully down position. Then the door will be pulled to the closed and latched position by a motor. The power back door cannot be opened using the switches at any time in the safe mode. The auto reverse function remains active while the door is closing in the safe mode. ● Do not activate the power back door if one or both of the back door gas stays are removed. Damage to the back door or power back door mechanisms may occur. BACK DOOR RELEASE WARNING ● Always be sure the back door has been closed securely to prevent it from opening while driving. ● Do not drive with the back door open. This could allow dangerous exhaust gases to be drawn into the vehicle. See “Exhaust gas” in the “Starting and driving” section of this manual. Do not operate the back door again until it is checked by your NISSAN dealer. 3-18 Pre-driving checks and adjustments Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X CAUTION ● If the power back door does not stay open or if the door unexpectedly closes at any time while a continuous warning chime sounds, do not operate the back door. There may be a pressure loss in one or both of the back door gas stays. Have the back door inspected by a NISSAN dealer. ● Do not activate the power back door if one or both of the back door gas stays are removed. Damage to the back door or power back door mechanisms may occur. LPD0230 Manual release LPD0236 Power release Manual back door (if so equipped) Power back door (if so equipped) If the back door cannot be locked or unlocked with the door lock switch or the keyfob due to a discharged battery, follow these steps: If the back door cannot be opened with the door lock switch or keyfob due to a discharged battery, follow these steps: 1. Remove the cover on the inside of the back door. 1. Remove the cover on the inside of the back door. 2. Move the lever down to lock or up to unlock. 2. Move the lever up to open the door. Pre-driving checks and adjustments 3-19 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X FUEL FILLER LID WARNING ● Gasoline is extremely flammable and highly explosive under certain conditions. You could be burned or seriously injured if it is misused or mishandled. Always stop the engine and do not smoke or allow open flames or sparks near the vehicle when refueling. ● Fuel may be under pressure. Turn the cap a third of a turn, and wait for any “hissing” sound to stop to prevent fuel from spraying out and possibly causing personal injury. Then remove the cap. LPD0220 LPD0232 OPENER OPERATION FUEL FILLER CAP The fuel filler lid release is located on the driver’s door. To open the fuel filler lid, push the release. To lock, close the fuel filler lid securely. The fuel filler cap is a ratcheting type. Turn the cap counterclockwise to remove. To tighten, turn the cap clockwise until ratcheting clicks are heard. 1 while Put the fuel filler cap on the cap holder s refueling. ● Do not attempt to top off the fuel tank after the fuel pump nozzle shuts off automatically. Continued refueling may cause fuel overflow, resulting in fuel spray and possibly a fire. ● Use only an original equipment type fuel filler cap as a replacement. It has a built-in safety valve needed for proper operation of the fuel system and emission control system. An incorrect cap can result in a serious malfunction and possible injury. It could also cause the malfunction indicator lamp to come on. ● Never pour fuel into the throttle body to attempt to start your vehicle. 3-20 Pre-driving checks and adjustments Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X STEERING WHEEL ● Do not fill a portable fuel container in the vehicle or trailer. Static electricity can cause an explosion of flammable liquid, vapor or gas in any vehicle or trailer. To reduce the risk of serious injury or death when filling portable fuel containers: – Always place the container on the ground when filling. – Do not use electronic devices when filling. – Keep the pump nozzle in contact with the container while you are filling it. – Use only approved portable fuel containers for flammable liquid. CAUTION ● If fuel is spilled on the vehicle body, flush it away with water to avoid paint damage. ● Tighten until the fuel filler cap clicks. Failure to tighten the fuel filler cap malproperly may cause the function indicator lamp (MIL) to illuminate. If the lamp illuminates because the fuel filler cap is loose or missing, tighten or install the cap and continue to drive the vehicle. The lamp should turn off after a lamp few driving trips. If the does not turn off after a few driving trips, have the vehicle inspected by a NISSAN dealer. ● For additional information, see the “Malfunction indicator lamp (MIL)” in the “Instruments and Controls” section earlier in this manual. LPD0216 TILT OPERATION Pull the lock lever forward and adjust the steering wheel up or down to the desired position. Push the lock lever back to lock the steering wheel in place. WARNING Do not adjust the steering wheel while driving. You could lose control of your vehicle and cause an accident. Pre-driving checks and adjustments 3-21 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X PEDAL POSITION ADJUSTMENT (if so equipped) SUN VISORS 1 s To block glare from the front, swing down the main sun visor. 2 s To block glare from the side, remove the main sun visor from the center mount and swing the visor to the side. 3 s Slide the extension sun visor in or out as needed. CAUTION ● Do not store the sun visor before returning it to its original position. ● Do not store the main sun visor before storing the extension sun visor. LPD0227 The accelerator and brake pedals can be adjusted for driving comfort. Use the pedal adjusting switch to adjust the 1 brake and accelerator pedal position forward s 2 . Pedal adjustment can only be or backward s performed when: ● Ignition switch is in the OFF or ACC position ● Ignition switch is ON and the selector lever is in the P (Park) position The brake and accelerator pedals cannot be adjusted separately. ● Do not pull the extension sun visor forcedly downward. CAUTION Do not adjust the pedal position with your foot on the pedal. LPD0217 3-22 Pre-driving checks and adjustments Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X MIRRORS LPD0218 WPD0126 VANITY MIRRORS INSIDE MIRROR (if so equipped) To access the vanity mirror, pull the sun visor down and flip open the mirror cover. The vanity mirror will illuminate when the mirror cover is open. 1 reduces glare from the The night position s headlights of vehicles behind you at night. 2 when driving in daylight Use the day position s hours. WARNING Use the night position only when necessary, because it reduces rear view clarity. LPD0194 AUTOMATIC ANTI-GLARE INSIDE MIRROR (if so equipped) The inside mirror is designed so that it automatically changes reflection according to the intensity of the headlights of the vehicle following you. When the AUTO switch is in the ON position, the 1 will illuminate and excessive indicator light s glare from the headlights of the vehicle behind you will be reduced. When the switch of the inside mirror is in the OFF position, the inside mirror will operate normally. Pre-driving checks and adjustments 3-23 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X For information on HomeLinkT Universal Transceiver operation, see the “HomeLinkT Universal Transceiver” in the “Instrument and controls” section of this manual. WARNING ● Objects viewed in the outside mirror on the passenger side are closer than they appear. Be careful when moving to the right. Using only this mirror could cause an accident. Use the inside mirror or glance over your shoulder to properly judge distances to other objects. ● Do not adjust the mirrors while driving. You could lose control of your vehicle and cause an accident. LPD0237 OUTSIDE MIRRORS The outside mirror remote control will operate only when the ignition switch is in the ACC or ON position. 1 to select the right or left Move the small switch s mirror. Adjust each mirror to the desired position 2 . using the large switch s 3-24 Pre-driving checks and adjustments Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X AUTOMATIC DRIVE POSITIONER (if so equipped) Move the shift selector lever to R (Reverse). The selected mirror will turn downward. The selected mirror surface will return to its original position when any of the following have occurred: The automatic drive positioner system has two features: ● Memory storage function ● Entry/exit function ● The shift selector lever is moved to any position other than R (Reverse). ● The outside mirror control switch is set to the neutral position. ● The ignition switch is turned OFF. NOTE: MPA0008 Foldable outside mirrors Push the mirrors backward to fold them. Reverse tilt-down feature (if so equipped) The reverse tilt-down feature will turn the selected outside mirror surface downward to provide better rear visibility close to the vehicle. If the outside mirror control switch is in the neutral position, neither mirror will turn downward when the shift selector lever is moved to R (Reverse). For more information regarding this feature and how to save the R (Reverse) mirror tilt-down adjustment in the automatic drive positioner memory, refer to “Automatic drive positioner” later in this section. When the ignition switch is in the ON position, turn the outside mirror control switch to the left or right position. Only one mirror can be selected at a time. Pre-driving checks and adjustments 3-25 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X 3. Adjust the driver’s seat, accelerator and brake pedals, and outside mirrors to the desired positions by manually operating each adjusting switch. For additional information, see “Seats” in the “Safety—Seats, seat belts and supplemental air bags” section and “Pedal position adjustment” and “Outside mirrors” earlier in this section. During this step, do not turn the ignition to any position other than ON. 4. Push the SET switch and, within 5 seconds, push the memory switch (1 or 2) fully for at least 1 second. LPD0219 MEMORY STORAGE FUNCTION Two positions for the driver’s seat, accelerator and brake pedals, and outside mirrors can be stored in the automatic drive positioner memory. Follow these procedures to use the memory system. 1. Set the automatic transmission selector lever to the P (Park) position. 2. Turn the ignition ON. The indicator light for the pushed memory switch will come on and stay on for approximately 5 seconds after pushing the switch. After the indicator light goes off, the selected positions are stored in the selected memory (1 or 2). 2. While the indicator light for the memory switch being set is illuminated for 5 secbutton on the keyfob. onds, press the The indicator light will blink. After the indicator light goes off, the keyfob is linked to that memory setting. With the key removed from the ignition switch, press the button on the keyfob. The driver’s seat and outside mirrors will move to the memorized position. Procedure for storing the outside mirror positions for best visibility when backing up Two outside mirror positions for backing up can be stored in the automatic drive positioner memory. 1. Set the parking brake. If memory is stored in the same memory switch, the previous memory will be deleted. 2. Turn the ignition ON. (Do not start the engine.) Linking a keyfob to a stored memory position 3. Push the memory switch 1 or 2 fully for at least 1 second to operate the automatic drive positioner. A keyfob can be linked to a stored memory position with the following procedure. 1. Follow the steps for storing a memory position. 4. Turn the outside mirror control switch to L (left). 5. Depress the brake pedal. 3-26 Pre-driving checks and adjustments Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X 6. Move the automatic transmission shift lever to R (Reverse). 7. Adjust the mirror to the desired viewing position for backing up by operating the outside mirror control switch. 8. Push the SET switch and, within 5 seconds, push the memory switch 1 or 2 selected in step 3 fully for at least 1 second. ● The indicator light for the pushed memory switch will come on and stay on for approximately 5 seconds after pushing the switch. After the indicator light goes off, the selected mirror position is stored in the selected memory (1 or 2). 9. Turn the outside mirror control switch to R (right). Repeat the above procedure to adjust the right mirror position and store in the selected memory. ● When the driver’s seat, outside mirror and steering column are not in the memorized position, the outside mirror will move with the initial tilt-down angle. Confirming memory storage ● Turn the ignition ON and push the SET switch. If the main memory has not been stored, the indicator light will come on for approximately 0.5 seconds. When the memory has stored the position, the indicator light will stay on for approximately 5 seconds. ● If the battery cable is disconnected, or if the fuse blows, the memory will be canceled. In such a case, reset the desired positions using the following procedures. 1. Open and close the driver’s door more than two times with the ignition key in the LOCK position. 2. Reset the desired position using the previous procedure. Selecting the memorized position 1. Set the automatic transmission selector lever to the P (Park) position. ENTRY/EXIT FUNCTION This system is designed so that the driver’s seat will automatically move when the automatic transmission selector lever is in the P (Park) position. This allows the driver to get into and out of the driver’s seat more easily. The driver’s seat will slide backward: ● When the key is removed from the ignition switch. ● When the driver’s door is opened with the key turned to LOCK. ● When the key is turned from ACC to LOCK with the driver’s door open while the automatic transmission selector lever is in the P (Park) position. The driver’s seat will return to previous position: 2. Turn the ignition ON. 3. Push the memory switch (1 or 2) fully for at least 1 second. ● When the key is inserted into the ignition switch. The driver’s seat, accelerator and brake pedals, and outside mirrors will move to the memorized position with the indicator light blinking, and then the light will stay on for approximately 5 seconds. ● When the driver’s door is closed with the key turned to LOCK. ● When the key is turned from ACC to ON while the automatic transmission selector lever is in the P (Park) position. The entry/exit function can be adjusted or canceled. See “Personalized settings menu” (vehicles without navigation system) or “Vehicle Pre-driving checks and adjustments 3-27 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X electronic systems” (vehicles with navigation system) in the “Display screen, heater, air conditioner and audio systems” section of this manual. navigation system) in the “Display screen, heater, air conditioner and audio systems” section of this manual. SYSTEM OPERATION The automatic drive positioner system will not work or will stop operating under the following conditions: ● when the vehicle speed is above 4 MPH (7 km/h). ● when any two or more of the memory switches are simultaneously pushed while the automatic drive positioner is operating. ● when the adjusting switch for the driver’s seat is turned on while the automatic drive positioner is operating. ● when the memory switch (1 or 2) is not pushed for at least 1 second. ● when the seat has been already moved to the memorized position. ● when no seat position is stored in the memory switch. The automatic drive positioner system can be adjusted and canceled. See “Personalized settings menu” (vehicles without navigation system) or “Vehicle electronic systems” (vehicles with 3-28 Pre-driving checks and adjustments Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X MEMO Pre-driving checks and adjustments 3-29 4 Display screen, heater, air conditioner and audio systems Control panel buttons — without navigation system. . . . 4-2 Names of components . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3 How to use JOYSTICK and “ENTER” button . . . . . . . 4-3 How to use “PREV” button . . . . . . . . . . . . . . . . . . . . . . 4-3 How to use “TRIP” button . . . . . . . . . . . . . . . . . . . . . . . 4-3 How to use “FUEL ECON” button . . . . . . . . . . . . . . . . 4-4 Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4 How to use “E/M” button . . . . . . . . . . . . . . . . . . . . . . . . 4-4 How to use (maintenance) button . . . . . . . . . . 4-5 How to use the “SETTING” button. . . . . . . . . . . . . . . . 4-5 button. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-7 Control panel buttons — with navigation system. . . . . . . 4-8 Names of the components. . . . . . . . . . . . . . . . . . . . . . . 4-8 How to use joystick and “ENTER” button . . . . . . . . . . 4-9 How to use “PREV” button . . . . . . . . . . . . . . . . . . . . . . 4-9 Setting up the start-up screen . . . . . . . . . . . . . . . . . . . 4-9 How to use the “TRIP” button . . . . . . . . . . . . . . . . . . . . 4-9 How to use the “SETTING” button. . . . . . . . . . . . . . . 4-12 button. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-16 Ventilators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-17 Heater and air conditioner (manual). . . . . . . . . . . . . . . . . 4-17 Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-18 Heater operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-19 Air conditioner operation . . . . . . . . . . . . . . . . . . . . . . . 4-20 Air flow charts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-21 Heater and air conditioner (automatic) (if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-27 Automatic operation . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-27 Manual operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-28 Rear control button . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-29 Operating tips. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-29 Rear seat air conditioner . . . . . . . . . . . . . . . . . . . . . . . . . . 4-29 Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-30 Servicing air conditioner. . . . . . . . . . . . . . . . . . . . . . . . . . . 4-30 Audio system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-30 Radio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-30 FM radio reception . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-31 AM radio reception . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-31 Satellite radio reception (if so equipped) . . . . . . . . . 4-31 Audio operation precautions . . . . . . . . . . . . . . . . . . . . 4-32 FM-AM-SAT radio with compact disc (CD) player (Type A)/CD changer (Type B) . . . . . . . . . . . . 4-34 CD care and cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . 4-41 Steering wheel switch for audio control (if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-41 Rear audio controls (if so equipped) . . . . . . . . . . . . . 4-43 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X Antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-43 DVD entertainment system (if so equipped). . . . . . . . . . 4-44 Digital video disc (DVD) player controls . . . . . . . . . . 4-45 Remote control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-46 Flip-down screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-46 Playing a digital video disc (DVD) . . . . . . . . . . . . . . . 4-48 Care and maintenance . . . . . . . . . . . . . . . . . . . . . . . . . 4-51 How to handle the DVD . . . . . . . . . . . . . . . . . . . . . . . . 4-52 Car phone or CB radio . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-53 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X CONTROL PANEL BUTTONS — WITHOUT NAVIGATION SYSTEM WARNING ● Positioning of the heating or air conditioning controls and display controls should not be done while driving in order that full attention may be given to the driving operation. ● Do not disassemble or modify this system. If you do, it may result in accidents, fire, or electrical shock. ● Do not use this system if you notice any abnormality, such as a frozen screen or lack of sound. Continued use of the system may result in accident, fire or electric shock. ● In case you notice any foreign object in the system hardware, spill liquid on it, or notice smoke or smell coming from it, stop using the system immediately and contact your nearest NISSAN dealer. Ignoring such conditions may lead to accidents, fire or electrical shock. LHA0326 When you use this system, make sure the engine is running. If you use the system with the engine not running (ignition ON or ACC) for a long time, it will use up all the battery power, and the engine will not start. Reference symbols: “ENTER” button — This is a button on the control panel. 4-2 Display screen, heater, air conditioner and audio systems Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X “Display” key — This is a select key on the screen. By selecting this key you can proceed to the next function. NAMES OF COMPONENTS 1. brightness control button (P. 4-7) HOW TO USE JOYSTICK AND “ENTER” BUTTON Choose an item on the display using the joystick. Push the “ENTER” button only when the use of it is instructed on the display. 2. PREV (previous) button (P. 4-3) HOW TO USE “PREV” BUTTON 3. Joystick and ENTER push button (P. 4-3) Finish setup: 4. SETTING button (P. 4-5) If you touch “PREV” button after the setup is completed, the setup will start over. 5. (maintenance) button (P. 4-5) 6. TRIP drive computer button (P. 4-3) 7. E/M (English/Metric) button (P. 4-4) LHA0252 8. FUEL ECON button (P. 4-4) HOW TO USE “TRIP” BUTTON 9. TRIP RESET button (P. 4-3) When the “TRIP” button is pushed, the following modes will display on the screen. 10. Clock adjust button (hours/minutes) (P. 4-4) To turn off the screen, push the button for more than approximately 1.5 seconds. The screen will change to “CONFIRM DISPLAY OFF YES or NO”. TRIP 1 (TIME, DIST, AVG) → TRIP 2 (TIME, DIST, AVG) → OFF TRIP 1 and TRIP 2 record journey time (TIME — max 99 hours 59 minutes), trip odometer (DIST — mile or km) and average speed (AVG — MPH or km/h). To reset the TRIP 1 or TRIP 2, push the “TRIP” button or the “TRIP RESET” button for more than approximately 1.5 seconds. Display screen, heater, air conditioner and audio systems 4-3 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X The display is updated every 30 seconds. For approximately the first 30 seconds and 1/3 miles (500 m) after a reset or connecting the battery cables, the display will show (----). CLOCK Distance to empty (dte — mile or km) If the power supply is disconnected, the clock will not indicate the correct time. Readjust the time. The distance to empty (dte) mode provides you with an estimation of the distance that can be driven before refueling. The dte is constantly being calculated based on the amount of fuel in the fuel tank and the actual fuel consumption. The display is updated every 30 seconds. LHA0253 HOW TO USE “FUEL ECON” BUTTON The average fuel consumption (MPG or L/100 km) and the distance to empty (dte — mi or km) will appear on the screen when the “FUEL ECON” button is pushed. Average fuel consumption (MPG or L/100 km) The digital clock displays time when the ignition key is in ACC or ON. Adjusting the time To adjust the time, push the “H” or “M” button for more than approximately 1.5 seconds. The time indicator will flash. When the fuel level is low, the dte display will change to (*). Touch the “H” button to adjust the hour. NOTE: To finish the adjusting, press the “PREV” button or the screen will return to normal after 10 seconds. ● If the amount of fuel added while the ignition switch is OFF is small, the display just before the ignition switch is turned OFF may continue to be displayed. ● When driving uphill or rounding curves, the fuel in the tank shifts, which may momentarily change the display. Touch the “M” button to adjust the minute. HOW TO USE “E/M” BUTTON You can change the unit as follows using the “E/M” (English/Metric) button. Unit: US — mile, °F, MPG Metric — km, °C, L/100 km The average fuel consumption mode shows the average fuel consumption since the last reset. Resetting is done by pressing the “TRIP RESET” or “FUEL ECON” button for more than approximately 1.5 seconds. 4-4 Display screen, heater, air conditioner and audio systems Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X In case of low tire pressure, a message (FLAT TIRE or CHECK ALL TIRE) is displayed on the screen: FLAT TIRE — very low tire air pressure. WARNING When a spare tire is mounted or a wheel is replaced, tire pressure will not be indicated and the low tire pressure warning system will not function. Contact your NISSAN dealer as soon as possible for tire replacement and/or system resetting. LHA0250 HOW TO USE (maintenance) BUTTON Pushing the button will change the maintenance menu as follows: ENGINE OIL → TIRE ROTATION→ TIRE PRESSURE To reset the driving distance, push the button or “TRIP RESET” button for more than approximately 1.5 seconds. To set the distance, push the joystick to left or right. LHA0383 Tire pressure information Pressure indication in **psi on the screen indicates that the pressure is being measured. After a few driving trips, the pressure for each tire will be displayed randomly. The order of the tire pressure figures displayed on the screen does not correspond with the actual order of the tire position. Tire pressure rises and falls depending on the heat caused by the vehicle’s operation and the outside temperature. HOW TO USE THE “SETTING” BUTTON Pushing the “SETTING” button will change the settings menu as follows: DISPLAY ON/OFF LANGUAGE BEEP SET SERVICE ALERT PERSONALIZED SETTINGS MENU Display ON/OFF To turn off the screen, select the OFF key of the “Display ON/OFF” using the joystick. Display screen, heater, air conditioner and audio systems 4-5 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X The screen will change to “CONFIRM DISPLAY OFF YES or NO”. If YES key is selected using the joystick, the screen will turn off after a 2 beep sound and approximately 1 second. To turn on the screen, push the “SETTING” , trip control, air conditioner (except rear window defogger button) or audio button. Language The language can be changed to “English” or “Français” using the joystick. Beep set If the beep set “OFF” key is selected using the joystick, the beep sound will not operate (except some caution beep sounds). Service alert If the service alert “ON” key is selected, the information will be displayed when the engine oil and the tire rotation periods reach the preset driving distance. Personalized settings menu You can set the following electronic systems operating conditions using the joystick. Slide back DR (driver’s) seat on exit: NOTE: The driver’s seat automatically moves back and returns to the original position for exceptional ease of exit and entry. If you change the horn beep or the lamp flash feature with the keyfob, the mode will not be changed with the display. Use the keyfob to return to the previous mode and re-enable the display control. Remote unlock door logic: This option allows you to select which doors will unlock first during an unlocking operation: Only the driver’s door ←→ All the doors Horn chirp with remote: This option allows you to select the horn chirp mode that occurs when the LOCK or UNLOCK button on the keyfob is pressed. Auto relock time: This option allows you to set the length of time before the doors lock with the auto re-lock function. Auto headlamp sensitivity: This option allows you to set the sensitivity of the autolights. Auto headlamp off delay: NOTE: If you change the horn beep or the lamp flash feature with the keyfob, the mode will not be changed with the display. Use the keyfob to return to the previous mode and re-enable the display control. Lamps flash with remote: This option allows you to select the hazard indicator flash mode that occurs when the LOCK or UNLOCK button on the keyfob is pressed. This option allows you to select the length of time before the autolights turn off. Speed sensing wiper interval: This option allows you to turn on or turn off the driving speed dependent intermittent wiper function. Confirm reset settings: This option allows you to reset all options to their default settings. 4-6 Display screen, heater, air conditioner and audio systems Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X BUTTON To change the display brightness, push the button. Pushing the button again will change the display to DAY or NIGHT display. Then, adjust the brightness moving the joystick right or left. If no operation is done within 10 seconds, or if the “PREV” button is pushed, the display will return to the previous display. ● In case you notice any foreign object in the system hardware, spill liquid on it, or notice smoke or smell coming from it, stop using the system immediately and contact your nearest NISSAN dealer. Ignoring such conditions may lead to accidents, fire or electrical shock. WARNING ● Positioning of the heating or air conditioning controls and display controls should not be done while driving in order that full attention may be given to the driving operation. ● Do not disassemble or modify this system. If you do, it may result in accidents, fire, or electrical shock. ● Do not use this system if you notice any abnormality, such as a frozen screen or lack of sound. Continued use of the system may result in accident, fire or electric shock. Display screen, heater, air conditioner and audio systems 4-7 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X CONTROL PANEL BUTTONS — WITH NAVIGATION SYSTEM “Display” key — This is a select key on the screen. By selecting this key you can proceed to the next function. NAMES OF THE COMPONENTS 1. brightness control button (P. 4-16) 2. PREV (previous) button (P. 4-9) 3. Joystick and ENTER push button (P. 4-9) 4. SETTING button (P. 4-12) 5. TRIP drive computer button (P. 4-9) 6. DEST button* 7. ROUTE button* 8. MAP button* 9. GUIDE VOICE button* LHA0377 When you use this system, make sure the engine is running. If you use the system with the engine not running (ignition ON or ACC) for a long time, it will use up all the battery power, and the engine will not start. Reference symbols: 10. zoom out button* 11. zoom in button* *For Navigation system control buttons, refer to the separate Navigation System Owner’s Manual. “ENTER” button — This is a button on the control panel. 4-8 Display screen, heater, air conditioner and audio systems Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X HOW TO USE JOYSTICK AND “ENTER” BUTTON Choose an item on the display using the joystick and push the “ENTER” button for operation. HOW TO USE “PREV” BUTTON If you do not touch the button or screen key for more than 1 minute on the TRIP, SETTING or START-UP screen, the screen will change to TRIP screen automatically. To proceed to the next step, refer to the separate Navigation System Owner’s Manual. This button has two functions. ● Go back to the previous display (cancel). If you touch “PREV” button during setup, the setup will be canceled and/or the display will return to the previous screen. ● Finish setup. If you touch this button after the setup is completed, the setup will start over, and the display will return to the climate control or audio mode and Navigation screen. SETTING UP THE START-UP SCREEN When you turn the ignition key to ACC or ON, the SYSTEM START-UP warning is displayed on the screen. Read the warning and select the “I AGREE” (English) or “ENTER” (Français) key then push the “ENTER” button. LHA0263 HOW TO USE THE “TRIP” BUTTON When the “TRIP” button is pushed, the following modes will display on the screen. Warning message (if there are any) → TRIP 1 (Elapsed Time, Driving Distance, Average Speed) → TRIP 2 → FUEL ECONOMY (Average Fuel Economy, Distance to Empty) → MAINTENANCE (Engine Oil, Tire Rotation) → OFF. If you do not push the “ENTER” button, the Navigation system will not proceed to the next step display. Display screen, heater, air conditioner and audio systems 4-9 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X LHA0264 LHA0320 Trip 1, trip 2 and fuel economy items Maintenance items To reset the TRIP 1, TRIP 2 and FUEL ECONOMY, select the “RESET” key using the joystick and push the “ENTER” button or push the “TRIP” button for more than approximately 1.5 seconds. You can set the engine oil and the tire rotation interval. To display the setting of the maintenance interval, select the “Engine Oil” or “Tire Rotation” key using the joystick and push the “ENTER” button. LHA0266 To set the maintenance interval, select the “Maintenance Schedule” key by using the joystick and push the joystick to right or left. To reset the maintenance interval, select the “Reset” key using the joystick and push the “ENTER” button. To display the MAINTENANCE INFORMATION automatically when set trip distance is reached, select the “Display Maintenance Notification” key and push the “ENTER” button. 4-10 Display screen, heater, air conditioner and audio systems Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X In case of low tire pressure, a message is displayed on the screen: FLAT TIRE — very low tire air pressure. WARNING When a spare tire is mounted or a wheel is replaced, tire pressure will not be indicated and the low tire pressure warning system will not function. Contact your NISSAN dealer as soon as possible for tire replacement and/or system resetting. LHA0267 LHA0362 Tire pressure information Pressure indication in ** psi on the screen indicates that the pressure is being measured. After a few driving trips, the pressure for each tire will be displayed randomly. The order of tire pressure figures displayed on the screen does not correspond with the actual order of the tire position. Tire pressure rises and falls depending on the heat caused by the vehicle’s operation and the outside temperature. Display screen, heater, air conditioner and audio systems 4-11 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X and push the “ENTER” button. You can then use the joystick to adjust the brightness to Darker or Brighter and the contrast to Lower or Higher. For information on Map Background, please refer to the separate Navigation System Owner’s Manual. Display Off: LHA0268 HOW TO USE THE “SETTING” BUTTON The SETTING screen will appear when the “SETTING” button is pushed. Display settings The DISPLAY SETTINGS screen will appear after pushing the “SETTING” button, selecting “Display” key and pushing the “ENTER” button. Brightness/Contrast/Map Background: To adjust the brightness and contrast of the screen, select the “Brightness/contrast” key To turn off the screen, push the “SETTING” button and select the “Display” key and “Display Off” key. The indicator of the “Display Off” will turn to amber. When any mode button is pushed with the screen off, the screen turns on for further operation. The screen will turn off automatically 5 seconds after the operation is finished on the map display in the Audio, HVAC (Heater and air conditioner), SETTING or VEHICLE INFO modes. To turn on the screen, push the “SETTING” button and select the “Display” key and “Display Off” key, then set the screen to on by pushing the “ENTER” button. Setting Audio or HVAC display: Choose the “Audio” or “HVAC” (Heater and air conditioner) key to be displayed at the bottom, by using the joystick. The audio or HVAC setting condition will normally appear on the screen. To return to the setting screen, push the “SETTING” button or “PREV” button. LHA0382 Vehicle electronic systems The VEHICLE ELECTRONIC SYSTEMS screen will appear when selecting the “Vehicle Electronic Systems” key with the joystick and pushing the “ENTER” button. To set the various electronic systems operating conditions, select the applicable item using the joystick, and push the “ENTER” button. The indicator light, box at left of selected item, alternately turns on and off each time the “ENTER” button is pressed. Indicator light is illuminated — ON 4-12 Display screen, heater, air conditioner and audio systems Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X NOTE: If you change the horn beep or the lamp flash feature with the keyfob, the mode will not be changed with the display. Use the keyfob to return to the previous mode and re-enable the display control. Keyless remote response — lights: This key allows you to change the hazard indicator flash mode that occurs when pressing the LOCK or UNLOCK button on the keyfob. NOTE: LHA0381 Indicator light is not illuminated — OFF LHA0261 With this option ON, the driver’s seat automatically moves back and returns to the original position for ease of exit and entry. If you change the horn beep or the lamp flash feature with the keyfob, the mode will not be changed with the display. Use the keyfob to return to the previous mode and re-enable the display control. Remote unlock driver’s door first: Auto re-lock time: Adjust driver seat when exiting vehicle: This option allows you to select which doors will unlock first during an unlocking operation: Only the driver’s door ←→ All the doors Keyless remote response — horn: This key allows you to change the horn chirp mode that occurs when pressing the LOCK or UNLOCK button on the keyfob. This key allows you to set the length of time before doors auto re-lock. Sensitivity of automatic headlights: This key allows you to set the sensitivity of the automatic headlights: ● Lower- less sensitive, automatic headlights will take longer to come on when the headlight sensor senses less ambient light. Display screen, heater, air conditioner and audio systems 4-13 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X ● Higher- more sensitive, automatic headlights will come on quicker when the headlight sensor senses less ambient light. Automatic headlights off delay: This key allows you to set the length of time before the automatic headlights turn off after exiting the vehicle. Speed dependent wiper: This key allows you to turn on or turn off the driving speed dependent intermittent wiper function. Return all settings to default: When this key is selected and turned on using the “ENTER” button, all settings made by VEHICLE ELECTRONICS will return to the default settings. LHA0262 LHA0270 System settings Clock Language/Unit Adjusting the time: The LANGUAGE/UNIT screen will appear when selecting the “Language/Unit” key and pushing the “ENTER” button. Select the “Hours” or “Minutes” key and move the joystick to the right or left to adjust the time. Language: English or French After completion of the setting, press the “PREV” button. Unit: US — mile, °F, MPG Metric — km, °C, L/100 km The time will change step by step. You can select the language and unit using the joystick and “ENTER” button. 4-14 Display screen, heater, air conditioner and audio systems Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X LHA0271 LHA0272 Setting daylight savings time: Adjusting the time to the GPS: Use the “Daylight Saving Time” key to adjust the clock to daylight savings time. Select the “Auto Adjust” key. ON: The displayed time advances by 1 hour. The time will be reset to the GPS time. LHA0273 Selecting the time zone: 1. Select the “Select Time Zone” key. The [TIME ZONE] screen will appear. OFF: The current time is displayed. Display screen, heater, air conditioner and audio systems 4-15 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X The GPS time (manual time) corresponding to the selected zone will be displayed. Pacific zone has been set as the initial (default) setting. Beep setting With this option ON, a beep will sound if any audio button is pushed. BUTTON To change the display brightness, push the button. Pushing the button again will change the display to DAY or NIGHT display. Then, adjust the brightness moving the joystick right or left. LHA0274 2. Select one of the following zones depending on the current location. If no operation is done within 10 seconds, or if the “PREV” button is pushed, the display will return to the previous display. ● Pacific zone ● Mountain zone ● Central zone ● Eastern zone ● Atlantic zone ● Newfoundland zone After selection, the [CLOCK SETTINGS] screen will appear. 4-16 Display screen, heater, air conditioner and audio systems Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X VENTILATORS HEATER AND AIR CONDITIONER (manual) WARNING ● The air conditioner cooling function operates only when the engine is running. LHA0328 Adjust air flow direction for the driver and pas1 , center s 2 , and rear passenger senger sides 3 ventilators by moving the ventilator slide s and/or ventilator assemblies. ● Do not leave children or adults who would normally require the support of others alone in your vehicle. Pets should not be left alone either. They could accidentally injure themselves or others through inadvertent operation of the vehicle. Also, on hot, sunny days, temperatures in a closed vehicle could quickly become high enough to cause severe or possibly fatal injuries to people or animals. ● Do not use the recirculation mode for long periods as it may cause the interior air to become stale and the windows to fog up. ● Positioning of the heater and/or air conditioner controls should not be done while driving so full attention may be given to vehicle operation. Display screen, heater, air conditioner and audio systems 4-17 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X — Air flows from center and side ventilators and the front and rear floor outlets. — Air flows mainly from the front and rear floor outlets. — Air flows from defroster outlets and the front and rear floor outlets. — Air flows mainly from defroster outlets. LHA0312 1. 2. 3. 4. 5. 6. 7. 8. Fan speed control dial Air recirculation button Temperature control dial Air conditioner button Air flow control dial Rear window defroster switch Rear fan speed dial Rear mode control and temperature dial CONTROLS Temperature control dial Fan control dial The fan control dial turns the fan on and off, and controls fan speed. Air flow control dial The air flow control dial allows you to select the air flow outlets. MAX A/C The air flow control dial also has intermediate positions which allow the air flow to be distributed between 2 of the icon positions on the air flow control dial. — Air flows from center and side vents with maximum cooling (air conditioning). — Air flows from center and side ventilators. The temperature control dial allows you to adjust the temperature of the outlet air. Air recirculation button ON position: Push the the vehicle. ( Push the button to recirculate air inside will appear on the display.) button to the on position when: ● driving on a dusty road. ● to prevent traffic fumes from entering passenger compartment. 4-18 Display screen, heater, air conditioner and audio systems Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X ● for maximum cooling when using the air conditioner. OFF position: Push the button again to turn air recirculation off. ( will appear on the display.) Outside air is drawn into the passenger compartment and distributed through the selected outlet. Use the off position for normal heater or air conditioner operation. Air conditioner button Start the engine, turn the fan control dial to the desired (1 to 4) position and push the button to turn on the air conditioner. A/C will appear on the display when the air conditioner is operating. To turn off the air conditioner, push the button again, the display will show A/C OFF. The air conditioner cooling function operates only when the engine is running. Rear window defroster switch For more information about the rear window defroster switch, see “Rear window defroster switch” in the “Instruments and controls” section of this manual. HEATER OPERATION Heating 4. Turn the temperature control dial to the desired position. This mode is used to direct heated air to the foot outlets. Some air also flows from the defrost outlets. 1. Push the button to the OFF position for normal heating ( shown on display). 2. Turn the air flow control dial to the position. 3. Turn the fan control dial to the desired position. 4. Turn the temperature control dial to the desired position between the middle and the hot position. Ventilation This mode directs outside air to the side and center ventilators. 1. Push the button to the OFF position ( shown on display). 2. Turn the air flow control dial to the position. 3. Turn the fan control dial to the desired position. Defrosting or defogging This mode directs the air to the defrost outlets to defrost/defog the windows. 1. Turn the air flow control dial to the position. 2. Turn the fan control dial to the desired position. 3. Turn the temperature control dial to the desired position between the middle and the hot position. ● To quickly remove ice or fog from the windows, turn the fan control dial to 4 and the temperature control lever to the full HOT position. ● When the position is selected, the air conditioner automatically turns on (however, A/C will not appear on the display) if the outside temperature is more than 36°F (2°C). The air conditioning system will continue to operate until the fan control dial is turned to OFF or the vehicle is shut off, even if the air flow control dial is turned to a position other than the position. This dehumidifies the air which helps defog the windshield. The mode automatically Display screen, heater, air conditioner and audio systems 4-19 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X turns off, allowing outside air to be drawn into the passenger compartment to further improve the defogging performance. Bi-level heating The bi-level mode directs warmed air to the side and center vents and to the front and rear floor outlets. 1. Push the button to the OFF position ( shown on display). 2. Turn the air flow control dial to the position. 3. Turn the fan control dial to the desired position. 4. Turn the temperature control dial to the desired position. Heating and defogging This mode heats the interior and defogs the windshield. 1. Turn the air flow control dial to the position. 2. Turn the fan control dial to the desired position. 3. Turn the temperature control dial to the desired position between the middle and the hot position. position is selected, the air ● When the conditioner automatically turns on (however, A/C will not appear on the display) if the outside temperature is more than 36°F (2°C). The air conditioning system will continue to operate until the fan control dial is turned to OFF or the vehicle is shut off, even if the air flow control dial is turned to a position other than the position. This dehumidifies the air which helps defog the mode automatically windshield. The turns off, allowing outside air to be drawn into the passenger compartment to further improve the defogging performance. Operating tips Clear snow and ice from the wiper blades and air inlet in front of the windshield. This improves heater operation. AIR CONDITIONER OPERATION Start the engine, turn the fan control dial to the desired (1 to 4) position, and push in the button to activate the air conditioner. When the air conditioner is on, cooling and dehumidifying functions are added to the heater operation. The air conditioner cooling function operates only when the engine is running. Cooling This mode is used to cool and dehumidify the air. 1. Push the button to the OFF position. 2. Turn the air flow control dial to the position. 3. Turn the fan control dial to the desired position. 4. Push the the display. button. A/C will appear on 5. Turn the temperature control dial to the desired position. ● For quick cooling when the outside temperature is high, push the button to the ON position ( shown on display). Be sure to return the to the OFF position for normal cooling ( shown on display). You may also select MAX A/C for quick cooling. Dehumidified heating This mode is used to heat and dehumidify the air. 1. Push the button to the OFF position ( shown on display). 2. Turn the air flow control dial to the position. 4-20 Display screen, heater, air conditioner and audio systems Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X 3. Turn the fan control dial to the desired position. 4. Push the A/C. button. The display shows 5. Turn the temperature control dial to the desired position. Operating tips ● Keep the windows and sunroof (if so equipped) closed while the air conditioner is in operation. AIR FLOW CHARTS The following charts show the button and dial positions for MAXIMUM AND QUICK heating, cooling or defrosting. For additional information on heating and cooling see “Heating” on page 4-19 and “Cooling” on page 4-20. The air recirculation ( ) button should always be in the OFF position for heating and defrosting. ● After parking in the sun, drive for 2 or 3 minutes with the windows open to vent hot air from the passenger compartment. Then, close the windows. This allows the air conditioner to cool the interior more quickly. ● The air conditioning system should be operated for approximately 10 minutes at least once a month. This helps prevent damage to the system due to lack of lubrication. ● If the engine coolant temperature gauge indicates engine coolant temperature over the normal range, turn the air conditioner off. See “If your vehicle overheats” in the “In case of emergency” section of this manual. Display screen, heater, air conditioner and audio systems 4-21 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X LHA0346 LHA0349 4-22 Display screen, heater, air conditioner and audio systems Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X LHA0348 LHA0347 Display screen, heater, air conditioner and audio systems 4-23 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X LHA0350 4-24 Display screen, heater, air conditioner and audio systems Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X LHA0351 Display screen, heater, air conditioner and audio systems 4-25 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X LHA0352 4-26 Display screen, heater, air conditioner and audio systems Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X HEATER AND AIR CONDITIONER (automatic) (if so equipped) ● Do not use the recirculation mode for long periods as it may cause the interior air to become stale and the windows to fog up. ● Positioning of the heater and/or air conditioner controls should not be done while driving so full attention may be given to vehicle operation. Start the engine and operate the controls to activate the air conditioner. AUTOMATIC OPERATION LHA0418 1. 2. 3. 4. 5. 6. 7. 8. Driver temperature control dial Fan control buttons and system OFF button Rear window and front window defroster dial MODE button and AUTO button Passenger temperature control dial A/C ON/OFF button and air recirculation button Rear control and fan speed dial Rear mode and temperature control dial WARNING ● The air conditioner cooling function operates only when the engine is running. ● Do not leave children or adults who would normally require the support of others alone in your vehicle. Pets should not be left alone either. They could accidentally injure themselves or others through inadvertent operation of the vehicle. Also, on hot, sunny days, temperatures in a closed vehicle could quickly become high enough to cause severe or possibly fatal injuries to people or animals. Cooling or heating (auto) This mode may be normally used all year round as the system automatically works to keep a constant temperature. Air flow distribution and fan speed are also controlled automatically. 1. Push the AUTO button on. (AUTO will be displayed.) 2. Turn the temperature dial to the left or right to set the desired temperature. Driver and passenger temperatures can be set independently. ● Adjust the temperature dial to about 75°F (24°C) for normal operation. Display screen, heater, air conditioner and audio systems 4-27 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X ● The temperature of the passenger compartment will be maintained automatically. Air flow distribution, fan speed and A/C on/off are also controlled automatically. Dehumidified defrosting or defogging 1. Turn the defroster control dial to the left. The display will show the defrost icon. 2. Turn the temperature dial to the left or right to set the desired temperature. ● To quickly remove ice from the outside of the windows, push the manual fan control button and set to the maximum position. ● As soon as possible after the windshield is clean, push the AUTO button to return to the auto mode. ● When the DEF control is activated, the air conditioner will automatically be turned on at outside temperatures above 36°F (2°C). If in defrost mode for more than one minute, the air conditioning system will continue to operate until the fan control is turned OFF or the vehicle is shut off, even if the air flow mode control button is used to select a position other than the position. This dehumidifies the air which helps defog the windshield. The air recirculate mode automatically turns off, allowing out- side air to be drawn into the passenger compartment to further improve the defogging performance. MANUAL OPERATION — Air flows from defroster and foot outlets. To turn system off Push and hold the fan down button until the system turns off. Fan speed control Push the fan control button to manually control the fan speed. up or down Push the AUTO button to return to automatic control of the fan speed. Air recirculation Push the air recirculation button to recirculate interior air inside the vehicle. Push the AUTO button to return to automatic mode. The air recirculation button will not be activated when the air conditioner is in DEF mode. Air flow control Pushing the MODE button manually controls air flow and selects the air outlet to: — Air flows from center and side ventilators. — Air flows from center and side ventilators and foot outlets. — Air flows mainly from foot outlets. 4-28 Display screen, heater, air conditioner and audio systems Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X REAR SEAT AIR CONDITIONER To operate the rear air conditioner, the engine must be running and the front air conditioner system must be on. The rear seat air conditioner can be turned on and off from the front controls. If the rear seat fan control dial is set to (0), the air conditioner is turned off. If it is set to any of the fan speed positions, air is discharged from the rear vents at the corresponding speed. When the rear seat fan control dial is set to (R), the rear seat passengers control their own fan speed. The rear seat air conditioner only works when the front seat air conditioner is operating. LHA0356 REAR CONTROL BUTTON You can adjust the climate control system for rear seat passengers using the buttons on the main control panel. Front passengers can control the rear functions by placing the controls on any setting other than the “R”. LIC0515 1 , located on the top center The sunload sensor s of the instrument panel, helps the system maintain a constant temperature. Do not put anything on or around this sensor. OPERATING TIPS ● When the engine coolant temperature and outside air temperature are low, the air flow from the foot outlets may not operate for a maximum of 150 seconds. However, this is not a malfunction. After the coolant temperature warms up, air flow from the foot outlets will operate normally. Display screen, heater, air conditioner and audio systems 4-29 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X SERVICING AIR CONDITIONER AUDIO SYSTEM The air conditioner system in your NISSAN vehicle is charged with a refrigerant designed with the environment in mind. RADIO This refrigerant does not harm the earth’s ozone layer. Special charging equipment and lubricant is required when servicing your NISSAN air conditioner. Using improper refrigerants or lubricants will cause severe damage to your air conditioner system. See “Air conditioner system refrigerant and lubricant recommendations” in the “Technical and consumer information” section of this manual. LHA0310 CONTROLS Fan control dial 1 turns the rear vent fan on The fan control dial s and off, and controls fan speed. Temperature control dial 2 allows rear pasThe temperature control dial s sengers to adjust the temperature and mode of the outlet air. A NISSAN dealer is able to service your “environmentally friendly” air conditioning system. WARNING The air conditioner system contains refrigerant under high pressure. To avoid personal injury, any air conditioner service should be done only by an experienced technician with proper equipment. Turn the ignition key to the ACC or ON position and press the ON·OFF/VOLUME control knob to turn the radio on. If you listen to the radio with the engine not running, the key should be turned to the ACC position. Radio reception is affected by station signal strength, distance from radio transmitter, buildings, bridges, mountains and other external influences. Intermittent changes in reception quality normally are caused by these external influences. Using a cellular phone in or near the vehicle may influence radio reception quality. Radio reception Your NISSAN radio system is equipped with state-of-the-art electronic circuits to enhance radio reception. These circuits are designed to extend reception range, and to enhance the quality of that reception. However there are some general characteristics of both FM and AM radio signals that can affect radio reception quality in a moving vehicle, even when the finest equipment is used. These characteristics are completely normal in a given reception area, and do not indicate any malfunction in your NISSAN radio system. 4-30 Display screen, heater, air conditioner and audio systems Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X Reception conditions will constantly change because of vehicle movement. Buildings, terrain, signal distance and interference from other vehicles can work against ideal reception. Described below are some of the factors that can affect your radio reception. FM RADIO RECEPTION Range: FM range is normally limited to 25 - 30 miles (40 - 48 km), with monaural (single channel) FM having slightly more range than stereo FM. External influences may sometimes interfere with FM station reception even if the FM station is within 25 miles (40 km). The strength of the FM signal is directly related to the distance between the transmitter and receiver. FM signals follow a line-of-sight path, exhibiting many of the same characteristics as light. For example they will reflect off objects. Fade and drift: As your vehicle moves away from a station transmitter, the signals will tend to fade and/or drift. Static and flutter: During signal interference from buildings, large hills or due to antenna position (usually in conjunction with increased distance from the station transmitter) static or flutter can be heard. This can be reduced by adjusting the treble control to reduce treble response. Multipath reception: Because of the reflective characteristics of FM signals, direct and reflected signals reach the receiver at the same time. The signals may cancel each other, resulting in momentary flutter or loss of sound. AM RADIO RECEPTION AM signals, because of their low frequency, can bend around objects and skip along the ground. In addition, the signals can be bounced off the ionosphere and bent back to earth. Because of these characteristics, AM signals are also subject to interference as they travel from transmitter to receiver. Fading: Occurs while the vehicle is passing through freeway underpasses or in areas with many tall buildings. It can also occur for several seconds during ionospheric turbulence even in areas where no obstacles exist. the vehicle outside of any metal or large building for satellite radio to receive all of the necessary data. No satellite radio reception is available and “NO SAT” is displayed when the SAT band option is selected unless optional satellite receiver and antenna are installed (retrofit unavailable without factory satellite radio pre-wiring), and an XMT or SIRIUS™ satellite radio service subscription is active. Satellite radio performance may be affected if cargo carried on the roof blocks the satellite radio signal. If possible, do not put cargo over the satellite antenna. Static: Caused by thunderstorms, electrical power lines, electric signs and even traffic lights. SATELLITE RADIO RECEPTION (if so equipped) When the satellite radio is first installed or the battery has been replaced, the satellite radio may not work properly. This is not a malfunction. Wait more than 10 minutes with satellite radio ON and Display screen, heater, air conditioner and audio systems 4-31 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X disc DIGITAL AUDIO” logo on the disc or packaging. ● During cold weather or rainy days, the player may malfunction due to the humidity. If this occurs, remove the CD and dehumidify or ventilate the player completely. ● The player may skip while driving on rough roads. ● Do not use the following CDs as they may cause the CD player to malfunction: ● 3.1 in (8 cm) discs with an adapter ● CDs that are not round ● CDs with a paper label ● CDs that are warped, scratched, or have abnormal edges ● The CD player sometimes cannot function when the compartment temperature is extremely high. Decrease the temperature before use. ● Do not expose the CD to direct sunlight. ● CDs that are in poor condition or are dirty, scratched or covered with fingerprints may not work properly. ● The following CDs may not work properly: LHA0099 AUDIO OPERATION PRECAUTIONS Compact disc (CD) player ● Copy control compact discs (CCCD) ● Recordable compact discs (CD-R) ● Rewritable compact discs (CD-RW) ● Only use high quality 4.7 inches (12 cm) round discs that have the “COMPACT 4-32 Display screen, heater, air conditioner and audio systems Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X 11. REAR AV button speaker control button 12. 13. Tuning and AUDIO control knob (BASS, TREBLE, FADE and BALANCE) 14. CD insert slot 15. CD eject button *No satellite radio reception is available and “NO SAT” is displayed when the SAT button is pressed unless optional satellite receiver and antenna are installed (retrofit unavailable without factory satellite radio pre-wiring), and an XMT or SIRIUS™ satellite radio service subscription is active. LHA0355 Type A 1. 2. 3. 4. 5. SEEK/TRACK change button TUNE/REW/FF button PAUSE/MUTE button PROG/RPT button ON·OFF/VOLUME control knob 6. 7. 8. 9. 10. PRESET A-B-C select button Station select buttons (1 - 6) CD play button FM-AM band select button SAT (satellite) radio select button* Display screen, heater, air conditioner and audio systems 4-33 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X 11. REAR AV button speaker control button 12. 13. Tuning and AUDIO control knob (BASS, TREBLE, FADE and BALANCE) 14. CD load button 15. CD insert slot 16. CD eject button *No satellite radio reception is available and “NO SAT” is displayed when the SAT button is pressed unless optional satellite receiver and antenna are installed (retrofit unavailable without factory satellite radio pre-wiring), and an XMT or SIRIUS™ satellite radio service subscription is active. LHA0321 Type B 1. 2. 3. 4. 5. SEEK/TRACK change button TUNE/REW/FF button PAUSE/MUTE button PROG/RPT button ON·OFF/VOLUME control knob 6. 7. 8. 9. 10. PRESET A-B-C select button Station and CD select buttons (1 - 6) CD play button FM-AM band select button SAT (satellite) radio select button* FM-AM-SAT RADIO WITH COMPACT DISC (CD) PLAYER (Type A)/CD CHANGER (Type B) No satellite radio reception is available and “NO SAT” is displayed when the SAT button is pressed unless optional satellite receiver and antenna are installed (retrofit unavailable without factory satellite radio pre-wiring), and an XMT or SIRIUS™ satellite radio service subscription is active. 4-34 Display screen, heater, air conditioner and audio systems Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X Audio main operation ON·OFF/Volume control: Turn the ignition key to ACC or ON, and then push the ON·OFF/Volume control knob while the system is off to call up the mode (radio or CD) which was playing immediately before the system was turned off. To turn the system off, press the ON·OFF/Volume control knob. Turn the ON·OFF/Volume control knob to adjust the volume. This vehicle has speed sensitive control volume (SSV) for audio. The audio volume changes as the driving speed changes. AUDIO knob (BASS, TREBLE, FADE, BALANCE and SSV): Press the AUDIO knob to change the mode as follows: BASS → TREBLE → FADE → BALANCE → SSV To adjust Bass, Treble, Fade and Balance, press the AUDIO knob until the desired mode appears in the display. Turn the Tuning knob to adjust Bass and Treble to the desired level. You can also use the Tuning knob to adjust Fader and Balance modes. Fader adjusts the sound level between the front and rear speakers and Balance adjusts the sound between the right and left speakers. To change the SSV mode to OFF, LOW, MID or HIGH, turn the Tuning knob to the right or left. Once you have adjusted the sound quality to the desired level, press the AUDIO knob repeatedly until the radio or CD display reappears. Otherwise, the radio or CD display will automatically reappear after about 10 seconds. Display CD text: To change the text displayed while playing a CD, press the AUDIO knob until “Display Mode” appears. Turn the Tuning knob within 2 seconds. The text will change as follows: Track number ←→ Track title ←→ Disc title ←→ Track number Display satellite radio text (if so equipped): Pause/mute button: To mute or pause the audio sound, push the PAUSE/MUTE button. To release the mute or pause, push the button again. FM/AM/SAT radio operation FM/AM/SAT band select: Pushing the FM-AM or SAT radio select button will change the band as follows: AM ←→ FM or SAT (Satellite- if so equipped) When FM-AM or SAT radio select button is pushed while the ignition switch is in the ACC or ON, the radio will come on at the station last played. The last station played will also come on when the ON·OFF/Volume control knob is depressed to ON. Turn the Tuning knob within 2 seconds. The text will change as follows: No satellite radio reception is available and “NO SAT” is displayed when the SAT button is pressed unless optional satellite receiver and antenna are installed (retrofit unavailable withouth factory satellite radio pre-wiring), and an XMT or SIRIUS™ satellite radio service subscription is active. Channel number ←→ Channel name ←→ Artist ←→ Title ←→ Channel number If a compact disc is playing when the FM-AM or SAT radio select button is pushed, the compact To change the text displayed while listening to satellite radio, press the AUDIO knob until “Display Mode” appears. Display screen, heater, air conditioner and audio systems 4-35 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X disc will automatically be turned off and the last radio station played will come on. The FM stereo indicator ST will glow during FM stereo reception. When the stereo broadcast signal is weak, the radio will automatically change from stereo to monaural reception. TUNE (Tuning): WARNING The radio should not be tuned while driving so full attention may be given to vehicle operation. To manually tune the radio, push the TUNE button ( or ) or turn the tuning knob to right or left. To move quickly through the channels, hold either the or button down for more than 1.5 seconds. SEEK tuning: Push the SEEK/TRACK button ( or ) for less than 1.5 seconds to tune from high to low or low to high frequencies and stop at the next broadcasting station. SCAN tuning: Radio data system (RDS): or button for more than Push the 1.5 seconds to stop at each broadcasting station for 5 seconds. Pushing the button again during this 5 second period will stop SCAN tuning and the radio will remain tuned to that station. If the or button is not pushed within 5 seconds, SCAN tuning moves to the next station. RDS stands for Radio Data System, and is a data information service transmitted by some radio stations on the FM band (not AM band) and/or SAT radio encoded within a regular radio broadcast. Currently, most RDS stations are in large cities, but many stations are now considering broadcasting RDS data. Station memory operations: RDS can display: 18 stations can be set for the FM, AM and SAT radio to the A, B and C preset button in any combination of AM or FM stations. ● Station call sign, such as “WHFR 98.3”. ● Station name, such as “The Groove”. 1. Choose preset channel A, B or C using the preset select button. ● Music or programming type such as “Classical”, “Country”, or “Rock”. 2. Tune to the desired station using manual, SEEK or SCAN tuning. Push and hold any of the desired station memory buttons (1 - 6) until a beep sound is heard. (The radio mutes when the select button is pushed.) ● Traffic reports about delays or construction. 3. The channel indicator will then come on and the sound will resume. Memorizing is now complete. 4. Other buttons can be set in the same manner. If the battery cable is disconnected, or if the fuse blows, the radio memory will be canceled. In that case, reset the desired stations. If the station broadcasts RDS information, the RDS icon is displayed. Program type (PTY): PTY can be used to search for a certain program type. Certain areas have a limited number of stations that transmit RDS. Many stations transmit call letters and frequencies only. Searching or scanning by program type may yield a limited number of selections. When PROG/RPT button is pressed for more than 1.5 seconds during FM or SAT (if so 4-36 Display screen, heater, air conditioner and audio systems Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X equipped) mode, the PTY name of the current tuned station is displayed. During this time if the PTY data code is zero or the data is unreadable, the display will show NONE. SEEK tuning: 3. After selecting a program type, push the or ) for less than SEEK button ( 1.5 seconds within 10 seconds. Tuning to the PTY station will start. If you do not push the SEEK button within the 10 second period, the PTY mode will be canceled. To change the PTY: 1. Press the PROG/RPT button. SCAN tuning: 4. Push the or button for more than 1.5 seconds to scan the PTY name stations and stop at each broadcasting station for 5 seconds. Pushing the button again during this 5 second period will stop SCAN tuning and the radio will remain tuned to that or button is not station. If the pushed within 5 seconds, SCAN tuning moves to the next station. Compact disc (CD) player operation (Type A) LHA0275 2. Press the TUNE button ( or ) to chose a specific program type. Refer to the illustration. The display will show “SEEK, SCAN?” CAUTION ● Do not force the compact disc into the slot. This could damage the player. ● Trying to load a CD with the CD door closed could damage the CD and/or CD changer. Display screen, heater, air conditioner and audio systems 4-37 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X Turn the ignition key to the ACC or ON position and insert the compact disc into the slot with the label side facing up. The compact disc will be guided automatically into the slot and start playing. If the radio is already operating, it will automatically turn off and the compact disc will play. If the system has been turned off while the compact disc was playing, pushing the ON·OFF/VOL control knob will start the compact disc. 3.1 in (8 cm) diameter compact discs can also be used without an adapter. CD button: When the CD button is pushed with the system off and the compact disc loaded, the system will turn on and the compact disc will start to play. When the CD button is pushed with the compact disc loaded but the radio playing, the radio will automatically be turned off and the compact disc will start to play. REW (Rewind), FF (Fast Forward): When the (rewind) or (fast forward) button is pushed while the compact disc is being played, the compact disc will play while rewinding or fast forwarding. When the button is released, the compact disc will return to normal play speed. SEEK/TRACK: button is pushed for less than When the 1.5 seconds while a compact disc is playing, the track being played returns to its beginning. Push several times to skip back through tracks. The compact disc will go back the number of times the button is pushed. When the button is pushed for less than 1.5 seconds while a compact disc is playing, the next track will start to play from its beginning. Push several times to skip through tracks. The compact disc will advance the number of times the button is pushed. (When the last track on the compact disc is skipped through, the first track will be played.) When the or button is pushed for more than 1.5 seconds, each track will play for about 10 seconds. To stop playing, push button. the REPEAT (RPT): ALL DISC RPT: the entire disk will be repeated 1 TRACK RPT: the current track will be repeated 1 DISC RDM: all tracks will be played randomly REAR AV: Pushing the REAR AV button for less than 1.5 seconds turns the rear seat audio controller on. Pushing it again will turn the rear seat audio controller off. If the vehicle is not equipped with a rear seat audio controller, the display will show “REAR AV N/A”. If a DVD is loaded in the DVD entertainment system (if so equipped), pushing the REAR AV button for more than 1.5 seconds will turn the DVD player on. When the REAR AV button is pushed for more than 1.5 seconds with a DVD loaded and another audio source playing, the other source will automatically be turned off and the DVD will start to play. (SPEAKER CONTROL) button: When the PROG/RPT button is pushed while the compact disc is being played, the play pattern can be changed as follows: ALL DISC RPT → 1 TRACK RPT → 1 DISC RDM → ALL DISC RPT Push this button to turn the rear speakers off and headphones on. Push this button again to turn rear seat speakers back on and headphones off. 4-38 Display screen, heater, air conditioner and audio systems Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X CD EJECT: button is pushed with the comWhen the pact disc loaded, the compact disc will be ejected. When button is pushed while the compact disc is being played, the compact disc will eject and the system will turn off. If the compact disc ejects and is not removed, it will be pulled back into the slot to protect it (except 3.1 in (8 cm) diameter compact discs). CD IN indicator: CD IN indicator appears on the display when the CD is loaded with the system on. Compact disc (CD) changer operation (Type B) CAUTION ● Do not force a compact disc into the CD insert slot. This could damage the CD and/or CD changer/player. ● Trying to load a CD with the CD door closed could damage the CD and/or CD changer. Turn the ignition key to the ACC or ON position and insert the compact disc into the slot with the label side facing up. The compact disc will be guided automatically into the slot and start playing. To insert the disc, first push the LOAD button. If the radio is already operating, it will automatically turn off and the compact disc will play. If the system has been turned off while the compact disc was playing, pushing the ON·OFF/VOL control knob will start the compact disc. LOAD button: To insert a CD in the CD changer, push the LOAD button for less than 1.5 seconds. Select the loading slot by pushing the CD insert select button (1 - 6), then insert the CD. To insert 6 CDs to the CD changer, push the LOAD button for more than 1.5 seconds. The slot numbers (1 - 6) will illuminate on the display when CDs are loaded into the changer. CD button: When the CD button is pushed with the system off and the compact disc loaded, the system will turn on and the compact disc will start to play. When the CD button is pushed with the compact disc loaded with the radio playing, the radio will automatically be turned off and the compact disc will start to play. REW (Rewind), FF (Fast Forward): When the (rewind) or (fast forward) button is pushed while a compact disc is playing, the compact disc will play while rewinding or fast forwarding . When the button is released, the compact disc will return to normal play speed. When the CD button is pushed with the system off and the compact disc loaded, the system will turn on and the compact disc will start to play. When the CD button is pushed with the compact disc loaded with the tape or the radio playing, the tape or radio will automatically be turned off and the compact disc will start to play. SEEK/TRACK: When the button is pushed for less than 1.5 seconds while a compact disc is playing, the track being played returns to its beginning. Push several times to skip back through tracks. The compact disc will go back the number of times the button is pushed. Display screen, heater, air conditioner and audio systems 4-39 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X When the button is pushed for less than 1.5 seconds while the compact disc is playing, the next track will start to play from its beginning. Push several times to skip through tracks. The compact disc will advance the number of times the button is pushed. (When the last track on the compact disc is skipped through, the first track will be played.) When pushing the or button for more than 1.5 seconds, each track will play for about 10 seconds. To stop playing, push the button again. CD select buttons: To play another CD that has been loaded, push a CD select button (1 - 6). REPEAT (RPT): When the PROG/RPT play button is pushed while the compact disc is played, the play pattern can be changed as follows: ALL DISC RPT → 1 DISC RPT→ 1 TRACK RPT → ALL DISC RDM → 1 DISC RDM → ALL DISC RPT ALL DISC RPT: All discs loaded will be repeated. 1 DISC RPT: The disc that is currently playing will be repeated. 1 TRACK RPT: The track that is currently playing will be repeated ALL DISC RDM: Tracks from all discs will be played randomly 1 DISC RDM: Tracks from the disc that is currently playing will be played randomly REAR AV: Pushing the REAR AV button for less than 1.5 seconds turns the rear seat audio controller on. Pushing it again will turn the rear seat audio controller off. If the vehicle is not equipped with a rear seat audio controller, the display will show “REAR AV N/A”. If a DVD is loaded in the DVD entertainment system (if so equipped), pushing the REAR AV button for more than 1.5 seconds will turn the DVD player on. When the REAR AV button is pushed for more than 1.5 seconds with a DVD loaded and another audio source playing, the other source will automatically be turned off and the DVD will start to play. (SPEAKER CONTROL) button: Push this button to turn the rear speakers off and headphones on. Push this button again to turn rear seat speakers back on and headphones off. CD EJECT: Current disc: ● Press the slot number (1 - 6) for the desired disc, then press the button. The compact disc will be ejected. If the disc is not removed within 15 seconds, the disc will reload (except 3.1 in [8 cm] diameter compact discs). All discs: ● Press and hold the button for more than 1.5 seconds. The compact discs will be ejected one by one. If a disc is not removed within 15 seconds, or the button is pressed again during the eject sequence, the entire disc eject sequence will be canceled. When this button is pushed while the compact disc is being played, the compact disc will eject and the last source will be played. CD IN indicator: The slot numbers (1 - 6) will illuminate if CDs have been loaded into the changer. 4-40 Display screen, heater, air conditioner and audio systems Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X MODE select switch Push the mode select switch to change the mode in the following sequence: AM, FM, SAT and CD. Volume control switch Push the volume control switch up or down to increase or decrease the volume. Tuning Memory change (radio): Push the tuning switch ( or ) for less than 1.5 seconds to change the radio frequency. LHA0049 CD CARE AND CLEANING ● Handle a CD by its edges. Do not bend the disc. Never touch the surface of the disc. ● Always place the discs in the storage case when they are not being used. ● To clean a disc, wipe the surface from the center to the outer edge using a clean, soft cloth. Do not wipe the disc using a circular motion. ● Do not use a conventional record cleaner or alcohol intended for industrial use. ● A new disc may be rough on the inner and outer edges. Remove the rough edges by rubbing the inner and outer edges with the side of a pen or pencil as illustrated. LHA0269 1. 2. 3. 4. Volume control switch MODE select switch POWER on/off switch Tuning switch STEERING WHEEL SWITCH FOR AUDIO CONTROL (if so equipped) The audio system can be operated using the controls on the steering wheel. POWER on/off switch With the ignition key turned to the ACC or ON position, push the POWER switch to turn the audio system on or off. Seek tuning (radio): Push the tuning switch ( or ) for more than 1.5 seconds to seek the next or previous radio station. FF, REW: Push the tuning switch ( or ) for less 1.5 seconds to return to the beginning of the present program or skip to the next program. Push several times to skip back or skip through programs. To stop the FF or REW function, press the or button for less than 1.5 seconds again. Display screen, heater, air conditioner and audio systems 4-41 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X When playing a CD in the CD changer (if so equipped), push the tuning switch ( or ) for more than 1.5 seconds to change between discs when multiple CDs are loaded. LHA0322 1. 2. 3. 4. 5. 6. VOL (volume) control button MODE select button speaker control button NEXT button SEEK button Headphone jacks 7. Infrared headphone transmitter lens* *Red transmitters will be visible when infrared headphones are on. 4-42 Display screen, heater, air conditioner and audio systems Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X REAR AUDIO CONTROLS (if so equipped) Push the REAR AV button on the front radio control panel to turn the rear controls on. Push the button again to turn rear controls off. The headphones symbol illuminates on the front display when the rear audio controls are on. Two headphone jacks are provided so two rear seat passengers may listen to the audio system privately. The rear volume controls can only increase the volume to the level at which the front radio volume control is set. One or two infrared headphones are included if the vehicle is equipped with the DVD entertainment system. Most portable radio headphones work with the rear audio controls. For vehicles equipped with the FM/AM/SAT radio with compact disc player, if the rear passengers turn off the rear speakers and are using headphones they may choose to listen to a different media than the front passengers. The rear passengers can listen to the radio while the front passengers can listen to the same thing, a CD or SAT radio (if so equipped). VOL (volume) button: The VOL button allows the rear passengers to adjust the headphone volume level. (SPEAKER CONTROL) button: Push this button to turn the rear speakers off and headphones on. Push this button again to turn rear seat speakers back on and headphones off. MODE button: The MODE button allows the rear passengers to change between AM, FM, CD, DVD and AUX. The media options are listed on the face plate of the rear audio controls. When a source of media is selected, the media label will be illuminated. SEEK button: ANTENNA Window antenna The antenna pattern is printed inside the rear passenger and driver side windows. CAUTION ● Do not place metalized film near the rear driver or passenger side window glass or attach any metal parts to it. This may cause poor reception or noise. ● When cleaning the inside of the rear driver or passenger side window, be careful not to scratch or damage the window antenna. Lightly wipe along the antenna with a dampened soft cloth. In AM or FM mode the SEEK button allows the rear seat passengers to find the next radio station up or down the station band frequency. In CD mode the SEEK button allows the rear passengers to find the next or previous selection on the CD. NEXT button: When the NEXT button is pushed while in AM or FM mode, the radio will change to the next preset. The NEXT button does not function while in SAT radio mode or when playing a DVD or CD. Display screen, heater, air conditioner and audio systems 4-43 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X DVD ENTERTAINMENT SYSTEM (if so equipped) CAUTION ● The glass screen on the liquid crystal display may break if hit with a hard or sharp object. If the glass breaks, do not touch the liquid crystalline material, which contains a small amount of mercury. In case of contact with skin, wash immediately with soap and water. ● Use a damp, soft cloth when cleaning the DVD Entertainment System components. Do not use solvents or cleaning solutions. LHA0327 WARNING ● The DVD Entertainment System is designed for rear seat passenger viewing only. ● Do not attempt to use the system in extreme temperature conditions [below -4°F (-20°C) or above 158°F (70°C)]. ● To avoid draining the vehicle battery, do not operate the system more than 15 minutes without starting the engine. ● The driver must not attempt to operate the DVD Entertainment System while the vehicle is in motion so that full attention may be given to vehicle operation. 4-44 Display screen, heater, air conditioner and audio systems Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X DIGITAL VIDEO DISC (DVD) PLAYER CONTROLS LHA0316 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. EJECT button DVD slot ENTER button POWER on/off button MODE button Input jacks STOP button PLAY/PAUSE button MENU button DISPLAY button NAVIGATION keys Display screen, heater, air conditioner and audio systems 4-45 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. DISPLAY button MODE button SUBTITLE button AUDIO button ANGLE button CLEAR button PAUSE button PLAY button FAST FORWARD/FAST REVERSE button MENU button NAVIGATION keys BACK button NUMERIC KEYPAD REMOTE CONTROL LHA0317 1. 2. 3. 4. 5. LHA0315 FLIP-DOWN SCREEN The flip-down screen has a wireless remote con1 located at the bottom of the trol receiver s screen. On vehicles equipped with 2 screens for second and third row passengers, both screens will have a remote control receiver. POWER button STOP button NEXT TRACK/CHAPTER and PREVIOUS TRACK/CHAPTER button TITLE button ENTER button 4-46 Display screen, heater, air conditioner and audio systems Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X CAUTION ● The glass screen on the liquid crystal display may break if hit with a hard or sharp object. If the glass breaks, do not touch the liquid crystalline material, which contains a small amount of mercury. In case of contact with skin, wash immediately with soap and water. ● The screen rotates down to view and up into the housing to store when not in use. Ensure that the screen is latched securely into the housing when stored. SAA0720 SAA0721 Headphones Display screen, heater, air conditioner and audio systems 4-47 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X Power ON/OFF: NOTE: Push the power button to turn the headphones on or off. For optimum infrared headphone performance, increase the volume on the rear seat controller to the maximum level and adjust the infrared headphone volume using the volume control on the headphones. Using a lower volume setting on the rear seat controller can cause static noise in the infrared headphones. Volume control: Turn the volume control knob to adjust the volume. The headphones will automatically be turned off in 30 seconds if there is no sound during that period. To prevent the battery from being discharged, keep the power suppy turned off when not in use. PLAYING A DIGITAL VIDEO DISC (DVD) CAUTION ● Only operate the DVD while the vehicle engine is running. Operating the DVD for extended periods of time with the engine OFF can discharge the vehicle battery. ● Do not allow the system to get wet. Excessive moisture such as spilled liquids may cause the system to malfunction. ● The driver must not attempt to wear the headphones while the vehicle is in motion so that full attention may be given to vehicle operation. ● While playing video CD media, this DVD player does not guarantee complete functionality of all video CD formats. With the DVD player, you can hear DVD videos, video CDs and CDs using headphones. Passengers in the rear seat can enjoy the sound independently of the front seat. Press the REAR AV button located on the front controls for more than 1.5 seconds to hear the sound of the DVD player through the speakers. Pushing the button on the front controls turns the rear speakers on and off. It is possible to operate the DVD player by remote control. Headphones are a wireless type and no cables are necessary. You can use them in almost all the ranges in the rear seat. (It is not possible to use the headphones in the front seat.) POWER on/off button: With the ignition switch turned to the ACC or ON position, push the POWER button to turn the DVD player on or off. Insert the DVD into the slot with the label side facing up. The DVD will be guided automatically into the slot. 4-48 Display screen, heater, air conditioner and audio systems Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X If the DVD player is off and a DVD is inserted, the DVD player will automatically turn on. CAUTION Do not force the compact disc into the slot. This could damage the player. MODE select button: Push the Mode button to select Audio/Video source between DVD and AUX input (input jacks on the faceplate, Red = right channel audio input, White = left channel audio input, and Yellow = Video input). The display will show the “AUX” in the upper left corner of the display for 4 seconds once the Mode is changed to AUX. To use the input jacks, refer to “Auxiliary input jacks” in this section. or PLAY: When the PLAY/PAUSE button on the player or the PLAY button on the remote control is pushed, the player will play. In play mode, the display will briefly show on the upper left corner of the display. FF (Fast Forward), REW (Remote control only): Push FAST FORWARD/FAST REVERSE buttons to carry out the fast forward or fast reverse presentation at 5 times normal play speed. Push FAST FORWARD/FAST REVERSE buttons again or PLAY button to resume the normal play speed. NEXT CHAPTER/ PREVIOUS CHAPTER (Remote control only): When the (NEXT CHAPTER) button is pushed while the DVD is being played, the program next to the present one will start to play from its beginning. Push several times to skip through programs. The DVD will advance the number of times the button is pushed. When the (PREVIOUS CHAPTER) button is pushed, the program being played returns to its beginning. Push several times to skip back through programs. The DVD will go back the number of times the button is pushed. or PAUSE: When the PLAY/PAUSE button on the player or the PAUSE button on the remote control is pushed, the player will pause playing of the media. In pause mode, the player will show on the upper left corner of the display until the player is changed to another mode. STOP: Push the STOP button once to stop playing the media. The display will show in the upper left corner of the display for 4 seconds, and the last disc position will be stored. When the PLAY button is pushed again, it will resume at the stored disc track and time position. If the STOP button is pushed again when the player is already in Stop mode, it will reinitialize the pointer to the beginning of the disc. In effect it will ignore the last stored disc position and upon receipt of the next play message it will begin at the Title Menu, or at “the beginning of the disc”. EJECT: When the EJECT button is pushed with the DVD loaded, it will be ejected. The display will show the EJECT symbol in the upper left corner of the display for 4 seconds once the EJECT button is pushed. If the DVD is not loaded, the display will show “NO DISC”. If the DVD comes out and is not removed within 25 seconds, it will be pulled back into the slot to protect it. Display screen, heater, air conditioner and audio systems 4-49 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X DISPLAY: If the DISPLAY control is pushed for less than 2 seconds, the display menu will appear on the screen. ● The display menu will remain on the screen for 10 seconds if no subsequent control activations occur. ● Use NAVIGATION KEYS to navigate within the display menu, and use ENTER to select the item. ● Holding the DISPLAY control on the faceplate for longer than approximately 2 seconds while in the display menu will reset the display characteristics to their nominal values. (Faceplate feature only) If the DISPLAY control button on the faceplate is pushed for more than 2 seconds, the media track/time information will be displayed along the bottom of the display. Pushing the DISPLAY control for more than 2 seconds will remove the media track/time information from the display. (Faceplate feature only) NAVIGATION KEYS: If media is in PLAY mode, activation of the NAVIGATION KEYS (Up, Down, Left, and Right) will perform the following functions: next chapter/track, previous chapter/track, fast re- verse and fast forward, and the display will show , , and respectively in the upper left corner of the display for 4 seconds. (Faceplate feature only) If media is in PAUSE mode, activation of the NAVIGATION KEYS (Up, Down and Right) will perform the following functions: next chapter/track, previous chapter/track and slow forward, and the display will show , and a forward arrow symbol respectively in the upper left corner of the display for 4 seconds. (Faceplate feature only) If media is in activated MENU mode, the NAVIGATION KEYS will be used to navigate Up, Down, Left, and Right within the menu. If display control menu is on, the NAVIGATION KEYS will be used to navigate Up, Down, Left, and Right within the menu. the screen. Use Navigation Keys to navigate within the menu, and use ENTER to select the item. Push the MENU button again to return to PLAY mode. TITLE (Remote control only): Push TITLE button to return the DVD media to the “title” of the DVD. Push TITLE button again to return to the previous stop point and play. BACK (Remote control only): Push the BACK button to exit the current active menu and return to the previous menu. SUBTITLE (Remote control only): ENTER: Push the SUBTITLE button to call up subtitle selection menu. In MENU mode, push the ENTER button to select MENU items. Repeatedly press the SUBTITLE button to cycle through each available subtitle. In the display menu, push the ENTER button to select items for modification, as per the onscreen instructions. AUDIO (Remote control only): MENU: If the media is in PLAY mode and the MENU button is pressed, the DVD menu will appear on Push the AUDIO button to call up audio menu. Repeatedly press the AUDIO button to cycle through each available audio track. 4-50 Display screen, heater, air conditioner and audio systems Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X ANGLE (Remote control only): Push the ANGLE button to call up camera angle menu. Repeatedly press the ANGLE button to cycle through each available angle. CLEAR (Remote control only): Push the CLEAR button to clear all numeric inputs, if actuated prior to expiration of the 3-second timer. NUMERIC KEYPAD (0–9 & ≥10) (Remote control only): Push the NUMERIC KEYPAD to directly access disc chapters, titles or tracks by inputting their numeric value. The operator can cancel the input chapter/title/track number by actuating the CLEAR control prior to the expiration of the 3-second timer. These functions can be used only for the DVD discs which correspond to them. Auxiliary input jacks The auxiliary input jacks are located on the control panel. Compatible devices such as video games camcorders and portable video players can be connected to the auxiliary jacks. ● Avoid touching or scratching the monitor screen as it may become dirty or damaged. ● Do not attempt to use the system in extreme temperature conditions [below -4°F (-20°C) or above 158°F (70°C)]. ● Do not attempt to operate the system in extreme humidity conditions (less than 10% or more than 75%). The auxiliary jacks are color coded for identification purposes. ● Yellow - video input ● White - left channel audio input The “≥10” button input numbers greater than or equal to 10, allowing up three digits to be input for selecting chapter/title/track number. CARE AND MAINTENANCE The subsequent actuation of numeric buttons will continuously shift the previously input number to the “left”. Use a lightly dampened, lint free cloth to clean the surfaces of your DVD Entertainment System. (DVD player face, screen, remote control, etc.) The chapter/title/track number will be automatically selected (if valid, based on media content) if 3 seconds expire without any keypad inputs. ● Do not use excessive force on the monitor screen. ● Red - right channel audio input CAUTION ● Do not use any solvents or cleaning solutions when cleaning the video system. Display screen, heater, air conditioner and audio systems 4-51 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X ● A new disc may be rough on its inner and outer edges. Remove the rough edges using the side of a pen or pencil as illustrated. ● Never attempt to use a DVD that has been cracked, deformed, or repaired using adhesive. Doing so may cause damage to the equipment. ● Handle the DVD carefully to avoid contamination or flaws. Otherwise, signals may not be read properly. LHA0049 HOW TO HANDLE THE DVD CAUTION ● Handle a DVD by its edges. Never touch the surface of the disc. ● To clean a disc, wipe the surface from the center to the outer edge using a clean, soft cloth. Do not wipe the disc using a circular motion. ● Do not write, draw or attach anything on any side of the DVD. ● Do not store the DVD in locations with direct sunlight or in high temperatures or humidity. ● Always place discs in the storage case when they are not being used. ● Do not put on any sticker or write anything on either surface of the DVD. ● Do not use a conventional record cleaner, benzine, thinner or alcohol intended for industrial use. LHA0318 Remote control and headphones battery replacement Replace the battery as follows: 1. Open the lid. 2. Replace batteries with new ones. ● Size AA (remote control) ● Size AAA (headphones) Make sure that the and ends on the batteries match the markings inside the compartment. 3. Close the lid securely. 4-52 Display screen, heater, air conditioner and audio systems Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X CAR PHONE OR CB RADIO ● When changing batteries, do not let dust or oil get on the remote control and headphones. FCC Notice: SAA0723 If the battery is removed for any reason other than replacement close the lid securely. ● If you will not be using the remote control for long periods of time, remove the batteries. ● Replacement of the batteries is needed when the remote control only functions at extremely close distances to the DVD player or not at all. ● Be careful not to touch the battery terminal. ● An improperly disposed battery can harm the environment. Always confirm local regulations for battery disposal. Changes or modifications not expressly approved by the manufacturer compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules and RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation of the device. When installing a CB, ham radio or car phone in your NISSAN, be sure to observe the following cautions, otherwise the new equipment may adversely affect the MFI (Multiport Fuel Injection) system and other electronic parts. WARNING ● A cellular telephone should not be used while driving so full attention may be given to vehicle operation. Some jurisdictions prohibit the use of cellular telephones while driving. ● If you must make a call while your vehicle is in motion, the hands free cellular phone operational mode (if so equipped) is highly recommended. Exercise extreme caution at all times so full attention may be given to vehicle operation. ● If a conversation in a moving vehicle requires you to take notes, pull off the road to a safe location and stop your vehicle before doing so. CAUTION ● Keep the antenna as far away as possible from the Engine Control Module (ECM). Display screen, heater, air conditioner and audio systems 4-53 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X ● Keep the antenna wire more than 8 in (20 cm) away from the Multiport Fuel Injection harness. Do not route the antenna wire next to any harness. ● Adjust the antenna standing-wave ratio as recommended by the manufacturer. ● Connect the ground wire from the CB radio chassis to the body. ● For details, consult a NISSAN dealer. 4-54 Display screen, heater, air conditioner and audio systems Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X 5 Starting and driving Precautions when starting and driving. . . . . . . . . . . . . . . . 5-2 Exhaust gas (carbon monoxide) . . . . . . . . . . . . . . . . . . 5-2 Three-way catalyst. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2 Low tire pressure warning system . . . . . . . . . . . . . . . . 5-3 Avoiding collision and rollover . . . . . . . . . . . . . . . . . . . . 5-4 Drinking alcohol/drugs and driving. . . . . . . . . . . . . . . . 5-5 Ignition switch. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5 Automatic transmission. . . . . . . . . . . . . . . . . . . . . . . . . . 5-5 Key positions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6 Nissan vehicle immobilizer system (NVIS) . . . . . . . . . 5-6 Before starting the engine . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6 Starting the engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-7 Driving the vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-7 Automatic transmission. . . . . . . . . . . . . . . . . . . . . . . . . . 5-7 Parking brake . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-11 Cruise control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-12 Precautions on cruise control . . . . . . . . . . . . . . . . . . . 5-12 Cruise control operations. . . . . . . . . . . . . . . . . . . . . . . 5-12 Break-in schedule . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-13 Increasing fuel economy. . . . . . . . . . . . . . . . . . . . . . . . . . . 5-14 Parking/parking on hills. . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-15 Power steering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-15 Brake system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-16 Brake precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-16 Anti-lock brake system (ABS) . . . . . . . . . . . . . . . . . . . 5-16 Traction control system (TCS). . . . . . . . . . . . . . . . . . . . . . 5-18 Vehicle dynamic control (VDC) system (if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-19 Rear sonar system (if so equipped) . . . . . . . . . . . . . . . . . 5-20 Cold weather driving . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-21 Freeing a frozen door lock . . . . . . . . . . . . . . . . . . . . . . 5-21 Anti-freeze . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-21 Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-21 Draining of coolant water . . . . . . . . . . . . . . . . . . . . . . . 5-21 Tire equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-21 Special winter equipment. . . . . . . . . . . . . . . . . . . . . . . 5-22 Driving on snow or ice . . . . . . . . . . . . . . . . . . . . . . . . . 5-22 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X PRECAUTIONS WHEN STARTING AND DRIVING WARNING ● Do not leave children or adults who would normally require the support of others alone in your vehicle. Pets should not be left alone either. They could accidentally injure themselves or others through inadvertent operation of the vehicle. Also, on hot, sunny days, temperatures in a closed vehicle could quickly become high enough to cause severe or possibly fatal injuries to people or animals. ● Properly secure all cargo with ropes or straps to help prevent it from sliding or shifting. Do not place cargo higher than the seatbacks. In a sudden stop or collision, unsecured cargo could cause personal injury. EXHAUST GAS (carbon monoxide) WARNING ● Do not breathe exhaust gases; they contain colorless and odorless carbon monoxide. Carbon monoxide is dangerous. It can cause unconsciousness or death. ● If you suspect that exhaust fumes are entering the vehicle, drive with all windows fully open, and have the vehicle inspected immediately. ● Do not run the engine in closed spaces such as a garage. ● Do not park the vehicle with the engine running for any extended length of time. ● Keep the back door and rear vent windows closed while driving, otherwise exhaust gases could be drawn into the passenger compartment. If you must drive with the back door or rear vent windows open, follow these precautions: 1. Open all the windows. 2. Set the air recirculation button to off and the fan control dial to high to circulate the air. ● If electrical wiring or other cable connections must pass to a trailer through the seal on the back door or the body, follow the manufacturer’s recommendation to prevent carbon monoxide entry into the vehicle. ● The exhaust system and body should be inspected by a qualified mechanic whenever: a. The vehicle is raised for service. b. You suspect that exhaust fumes are entering into the passenger compartment. c. You notice a change in the sound of the exhaust system. d. You have had an accident involving damage to the exhaust system, underbody, or rear of the vehicle. THREE-WAY CATALYST The three-way catalyst is an emission control device installed in the exhaust system. Exhaust gases in the three-way catalyst are burned at high temperatures to help reduce pollutants. WARNING ● The exhaust gas and the exhaust system are very hot. Keep people, animals or flammable materials away from the exhaust system components. 5-2 Starting and driving Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X ● Do not stop or park the vehicle over flammable materials such as dry grass, waste paper or rags. They may ignite and cause a fire. CAUTION ● Do not use leaded gasoline. Deposits from leaded gasoline will seriously reduce the three-way catalyst’s ability to help reduce exhaust pollutants. ● Keep your engine tuned up. Malfunctions in the ignition, fuel injection, or electrical systems can cause overrich fuel flow into the three-way catalyst, causing it to overheat. Do not keep driving if the engine misfires, or if noticeable loss of performance or other unusual operating conditions are detected. Have the vehicle inspected promptly by a NISSAN dealer. ● Avoid driving with an extremely low fuel level. Running out of fuel could cause the engine to misfire, damaging the three-way catalyst. ● Do not race the engine while warming it up. ● Do not push or tow your vehicle to start the engine. LOW TIRE PRESSURE WARNING SYSTEM This vehicle is equipped with the low tire pressure warning system, which displays pressure of all tires (except the spare tire) on the display screen by sending a signal from a sensor that is installed in each wheel. The low tire pressure warning system will activate only when the vehicle is driven at speeds above 20 MPH (32 km/h). Also, this system may not detect a sudden drop in tire pressure (for example a flat tire while driving). Tire pressure rises and falls depending on the heat caused by the vehicle’s operation and the outside temperature. Low outside temperature can lower the temperature of the air inside the tire which can cause a lower tire inflation pressure. This may cause the low tire pressure warning light to illuminate. sure figures displayed on the screen does not correspond with the actual order of the tire position.) See “Tire pressure information” in the “Display screen, heater, air conditioner and audio systems” section for tire pressure monitor. Low tire pressure warning If the vehicle is being driven with very low tire pressure (lower than 28 psi, 193 kPa), the low tire pressure warning light comes on and the chime sounds for about 10 seconds. For additional information regarding the above warning, see “Warning/indicator lights and audible reminders” in the “Instruments and controls” section. If the warning light illuminates in low ambient temperature as described above, check the tire pressure for all four tires. Adjust the tire pressure to the recommended COLD tire pressure shown on the Tire and Loading Information label to turn the low tire pressure warning light OFF. Frequently check the tire pressure information display on the display screen and adjust pressure of each tire properly. (The order of the tire pres- Starting and driving 5-3 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X WARNING ● If the low tire pressure warning light flashes while driving, avoid sudden steering maneuvers or abrupt braking, reduce vehicle speed, pull off the road to a safe location and stop the vehicle as soon as possible. Serious vehicle damage could occur and may lead to an accident and could result in serious personal injury. Check the tire pressure for all four tires. Adjust the tire pressure to the recommended COLD tire pressure shown on the Tire and Loading Information label to turn the low tire pressure warning light OFF. If you have a flat tire, replace it with a spare tire as soon as possible. (See “Flat tire” in the “In case of emergency” section for changing a flat tire.) ● When a spare tire is mounted or a wheel is replaced, tire pressure will not be indicated and the low tire pressure warning system will not function. Contact your NISSAN dealer as soon as possible for tire replacement and/or system resetting. ● Do not inject any tire liquid or aerosol tire sealant into the tires, as this may cause a malfunction of the tire pressure sensors. CAUTION Do not place metalized film or any metal parts (antenna, etc.) on the windows. This may cause poor reception of the signals from the tire pressure sensors, and the low tire pressure warning system will not function properly. FCC Notice: Changes or modifications not expressly approved by the manufacturer compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules and RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interface, and (2) this device must accept any interference received, including interference that may cause undesired operation of the device. AVOIDING COLLISION AND ROLLOVER WARNING Failure to operate this vehicle in a safe and prudent manner may result in loss of control or an accident. Be alert and drive defensively at all times. Obey all traffic regulations. Avoid excessive speed, high speed cornering, or sudden steering maneuvers, because these driving practices could cause you to lose control of your vehicle. As with any vehicle, loss of control could result in a collision with other vehicles or objects, or cause the vehicle to roll over, particularly if the loss of control causes the vehicle to slide sideways. Be attentive at all times, and avoid driving when tired. Never drive when under the influence of alcohol or drugs (including prescription or over-the-counter drugs which may cause drowsiness). Always wear your seat belt as outlined in the “Safety – Seats, seat belts and supplemental air bags” section of this manual, and also instruct your passengers to do so. Seat belts help reduce the risk of injury in collisions and rollovers. In a rollover crash, an unbelted or improperly belted person is significantly more likely to be injured or killed than a person wearing a seat belt. 5-4 Starting and driving Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X IGNITION SWITCH DRINKING ALCOHOL/DRUGS AND DRIVING 1. Move the shift selector lever into the P (Park) position. 2. Turn the ignition key slightly toward the ON position. WARNING Never drive under the influence of alcohol or drugs. Alcohol in the bloodstream reduces coordination, delays reaction time and impairs judgement. Driving after drinking alcohol increases the likelihood of being involved in an accident injuring yourself and others. Additionally, if you are injured in an accident, alcohol can increase the severity of the injury. NISSAN is committed to safe driving. However, you must choose not to drive under the influence of alcohol. Every year thousands of people are injured or killed in alcohol-related accidents. Although the local laws vary on what is considered to be legally intoxicated, the fact is that alcohol affects all people differently and most people underestimate the effects of alcohol. Remember, drinking and driving don’t mix! And that is true for drugs, too (over-the-counter, prescription, and illegal drugs). Don’t drive if your ability to operate your vehicle is impaired by alcohol, drugs, or some other physical condition. 3. Turn the key to the LOCK position. 4. Remove the key. The shift selector lever is designed so it cannot moved out of P (Park) and into any of the other gear positions if the ignition key is turned to OFF position or if the key is removed from the switch. WSD0041 AUTOMATIC TRANSMISSION The ignition lock is designed so the key cannot be turned to LOCK position and removed until the shift selector lever is moved to the P (Park) position. The shift selector lever can be moved if the ignition switch is in the ACC position. This allows the vehicle to be moved if the battery is discharged. The shift selector lever can also be moved if the ignition switch is in the ON position and the foot brake pedal is depressed. When removing the key from the ignition, make sure the shift selector lever is in the P (Park) position. There is an OFF position between the LOCK and ACC positions. The OFF position is indicated by a “1” on the key cylinder. When the ignition is in the OFF position, the steering wheel is not locked. If the selector lever is not returned to P (Park) position, the key cannot be move to the LOCK position. In order for the steering wheel to be locked, it must be turned about 1/8 of a turn clockwise from the straight up position. When the key cannot be turned to the LOCK position, proceed as follows to remove the key. To lock the steering wheel, turn the key to the LOCK position. Remove the key. To Starting and driving 5-5 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X BEFORE STARTING THE ENGINE unlock the steering wheel, insert the key and turn it gently while rotating the steering wheel slightly right and left. WARNING Never remove or turn the key to the LOCK position while driving. The steering wheel will lock. This may cause the driver to lose control of the vehicle and could result in serious vehicle damage or personal injury. KEY POSITIONS LOCK: Normal parking position (0) OFF: (Not used) (1) ACC: (Accessories) (2) This position activates electrical accessories such as the radio when the engine is not running. ON: Normal operating position (3) This position turns on the ignition system and the electrical accessories. START: (4) This position starts the engine. As soon as the engine has started, release the key. It automatically returns to the ON position. NISSAN VEHICLE IMMOBILIZER SYSTEM (NVIS) The NISSAN Vehicle Immobilizer System (NVIS) will not allow the engine to start without the use of the registered NVIS key. If the engine fails to start using the registered NVIS key, it may be due to interference caused by another NVIS key, an automated toll road device or automated payment device on the key ring. Restart the engine using the following procedures: 1. Leave the ignition switch in the ON position for approximately 5 seconds. 2. Turn the ignition switch to the OFF or LOCK position and wait approximately 5 seconds. 3. Repeat step 1 and 2 again. 4. Restart the engine while holding the device (which may have caused the interference) separate from the registered NVIS key. If this procedure allows the engine to start, NISSAN recommends placing the registered NVIS key on a separate key ring to avoid interference from other devices. ● Make sure the area around the vehicle is clear. ● Check fluid levels such as engine oil, coolant, brake fluid, and window washer fluid as frequently as possible, or at least whenever you refuel. ● Check that all windows and lights are clean. ● Visually inspect tires for their appearance and condition. Also check tires for proper inflation. ● Lock all doors. ● Position seat and adjust head restraints. ● Adjust inside and outside mirrors. ● Fasten seat belts and ask all passengers to do likewise. ● Check the operation of warning lights when the key is turned to the ON (3) position. See “Warning/indicator lights and audible reminders” in the “Instruments and controls” section of this manual. 5-6 Starting and driving Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X STARTING THE ENGINE 1. Apply the parking brake. 2. Move the shift selector lever to P (Park) or N (Neutral). P (Park) is recommended. The shift selector lever cannot be moved out of P (Park) and into any of the other gear positions if the ignition key is turned to the OFF position or if the key is removed from the ignition switch. The starter is designed not to operate if the shift selector lever is in any of the driving positions. 3. Crank the engine with your foot off the accelerator pedal by turning the ignition key to START. Release the key when the engine starts. If the engine starts, but fails to run, repeat the above procedure. ● If the engine is very hard to start in extremely cold weather or when restarting, depress the accelerator pedal a little (approximately 1/3 to the floor) and hold it and then crank the engine. Release the key and the accelerator pedal when the engine starts. ● If the engine is very hard to start because it is flooded, depress the accelerator pedal all the way to the floor and hold it. Crank the engine for 5-6 seconds. After DRIVING THE VEHICLE cranking the engine, release the accelerator pedal. Crank the engine with your foot off the accelerator pedal by turning the ignition key to START. Release the key when the engine starts. If the engine starts, but fails to run, repeat the above procedure. CAUTION Do not operate the starter for more than 15 seconds at a time. If the engine does not start, turn the key off and wait 10 seconds before cranking again, otherwise the starter could be damaged. 4. Allow the engine to idle for at least 30 seconds after starting. Do not race the engine while warming it up. Drive at moderate speed for a short distance first, especially in cold weather. In cold weather, keep the engine running for a minimum of 2–3 minutes before shutting it off. Starting and stopping the engine over a short period of time may make the vehicle more difficult to start. AUTOMATIC TRANSMISSION WARNING ● Do not depress the accelerator pedal while shifting from P (Park) or N (Neutral) to R (Reverse), or L (Low). Always depress the brake pedal until shifting is completed. Failure to do so could cause you to lose control and have an accident. ● Cold engine idle speed is high, so use caution when shifting into a forward or reverse gear before the engine has warmed up. ● Never shift to P (Park) or R (Reverse) while the vehicle is moving. This could cause an accident. CAUTION ● When stopping the vehicle on an uphill grade, do not hold the vehicle by depressing the accelerator pedal. The foot brake should be used for this purpose. ● Do not downshift abruptly on slippery roads. This may cause a loss of control. The automatic transmission in your vehicle is electronically controlled to produce maximum power and smooth operation. Starting and driving 5-7 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X The recommended operating procedures for this transmission are shown on the following pages. Follow these procedures for maximum vehicle performance and driving enjoyment. WARNING Apply the parking brake if the selector lever is in any position while the engine is not running. Failure to do so could cause the vehicle to move unexpectedly or roll away and result in serious personal injury or property damage. Starting the vehicle 1. After starting the engine, fully depress the foot brake pedal before attempting to move the shift selector lever out of the P (Park) position. 2. Keep the foot brake pedal depressed and move the shift selector lever into a driving gear. 3. Release the foot brake, then gradually start the vehicle in motion. The automatic transmission is designed so the foot brake pedal MUST be depressed before shifting from P (Park) to any drive position while the ignition switch is in the ON position. The shift selector lever cannot be moved out of P (Park) and into any of the other gear positions if the ignition key is turned to the LOCK, OFF or ACC position or if the key is removed. LSD0081 To move the selector lever: : Push the button while depressing the brake pedal : Push the button to shift : Shift without pushing button If the key is turned to the OFF or ACC position for any reason while the vehicle is in N (Neutral), or any D (Drive) position, the shift selector lever cannot be moved to P (Park). Additionally, the key cannot be turned to the LOCK position and be removed from the ignition switch. If this occurs, perform the following steps: 1. Apply the parking brake when the vehicle is stopped. 2. Turn the key to the ON position. 3. Depress the foot brake pedal. Shifting After starting the engine, fully depress the brake pedal and move the shift selector lever out of the P (Park) position. 5-8 Starting and driving Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X 4. Move the shift selector lever to P (Park) or N (Neutral) to restart the vehicle (P is preferred). Move the shift selector lever to P (Park) to park the vehicle and turn the ignition key to the LOCK position to remove the key. P (Park): Use this selector position when the vehicle is parked or when starting the engine. Make sure the vehicle is completely stopped. The brake pedal must be depressed to move the selector lever from N (Neutral) or any drive position to P (Park). Apply the parking brake. When parking on a hill, apply the parking brake first, then move the shift selector lever into the P (Park) position. R (Reverse): CAUTION Use this position only when the vehicle is completely stopped. Use this position to back up. Make sure the vehicle is completely stopped before selecting the R (Reverse) position. The brake pedal must be depressed to move the selector lever from P (Park), N (Neutral) or any drive position to R (Reverse). N (Neutral): Neither forward nor reverse gear is engaged. The engine can be started in this position. You may shift to N (Neutral) and restart a stalled engine while the vehicle is moving. D (Drive): Use this position for all normal forward driving. L (Low gear): Use this position when climbing steep hills slowly or slow driving through deep snow, sand or mud, or for maximum engine braking on steep downhill grades. Do not shift into the L position at speeds above 65 MPH (105 km/h). Do not exceed 65 MPH (105 km/h) in the L position. WSD0083 Shift lock release If the battery is discharged, the shift selector lever may not be moved from the P (Park) position even with the brake pedal depressed. To move the shift selector lever, release the shift lock. The shift selector lever can be moved to N (Neutral). However, the steering wheel will be locked unless the ignition switch is turned to the ON position. This allows the vehicle to be moved if the battery is discharged. Starting and driving 5-9 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X To push the shift lock release, complete the following procedure: 1. Turn the ignition key to the LOCK position and remove the key 2. Apply the parking brake. 3. Remove the shift lock release cover as shown. 4. Insert a small screwdriver in the shift lock release slot and push down. 5. Move the shift selector lever to the N (Neutral) position while holding down the shift lock release. 6. Turn the key to the ON position to unlock the steering wheel. Now the vehicle may be moved to the desired location. If the shift selector lever cannot be moved out of P (Park), have a NISSAN dealer check the automatic transmission system as soon as possible. WARNING If the selector lever cannot be moved from the P (Park) position while the engine is running and the brake pedal is depressed, the stop lights may not work. Malfunctioning stop lights could cause an accident injuring yourself and others. Accelerator downshift — in D position — For passing or hill climbing, depress the accelerator pedal to the floor. This shifts the transmission down into a lower gear, depending on the vehicle speed. Fail-safe When the fail-safe operation occurs, please note that the 4–speed automatic transmission will be locked in third gear. For the 5–speed automatic transmission, the transmission will be locked in any of the gears according to the condition. If the vehicle is driven under extreme conditions, such as excessive wheel spinning and subsequent hard braking, the fail-safe system may be activated. This will occur even if all electrical circuits are functioning properly. In this case, turn the ignition key OFF and wait for 3 seconds. Then turn the key back to the ON position. The vehicle should return to its normal operating condition. If it does not return to its normal operating condition, have a NISSAN dealer check the transmission and repair it if necessary. WSD0084 Overdrive switch Each time your vehicle is started, the transmission is automatically “reset” to overdrive ON. ON: With the engine running and the shift selector lever in the D (Drive) position, the transmission upshifts into Overdrive as vehicle speed increases. Overdrive does not engage until the engine has reached operating temperature. 5-10 Starting and driving Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X PARKING BRAKE OFF: For driving up and down long slopes where engine braking is necessary push the Overdrive switch once. The O/D OFF indicator light in the instrument panel comes on at this time. When cruising at a low speed or climbing a gentle slope, you may feel uncomfortable shift shocks as the transmission shifts into and out of Overdrive repeatedly. In this case, depress the Overdrive switch to turn the Overdrive off. The O/D OFF indicator light in the instrument panel comes on at this time. When driving conditions change, depress the Overdrive switch to turn the Overdrive on. Remember not to drive at high speeds for extended periods of time with the Overdrive off. This reduces fuel economy. WARNING ● Be sure the parking brake is fully released before driving. Failure to do so can cause brake failure and lead to an accident. ● Do not release the parking brake from outside the vehicle. ● Do not use the gear shift in place of the parking brake. When parking, be sure the parking brake is fully engaged. ● Do not leave children unattended in a vehicle. They could release the parking brake and cause an accident. LSD0082 To engage: Firmly depress the parking brake. To release: 1. Firmly apply the foot brake. 2. Move the shift selector lever to the P (Park) position. 3. Firmly depress the parking brake pedal again and it will release. 4. Before driving, be sure the brake warning light goes out. Starting and driving 5-11 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X CRUISE CONTROL ● The SET indicator light may blink when the cruise control main switch is turned ON while pushing the ACCEL/RES, COAST/SET, or CANCEL switch (located on the steering wheel). To properly set the cruise control system, use the following procedures. WARNING Do not use the cruise control when driving under the following conditions: ● When it is not possible to keep the vehicle at a set speed. LSD0075 1. 2. 3. 4. ACCEL/RES switch COAST/SET switch ON/OFF switch CANCEL switch PRECAUTIONS ON CRUISE CONTROL ● If the cruise control system malfunctions, it cancels automatically. The SET indicator light in the instrument panel then blinks to warn the driver. ● If the SET indicator light blinks, turn the cruise control main switch off and have the system checked by a NISSAN dealer. ● In heavy traffic or in traffic that varies in speed. ● On winding or hilly roads. ● On slippery roads (rain, snow, ice, etc.). ● In very windy areas. Doing so could cause a loss of vehicle control and result in an accident. CRUISE CONTROL OPERATIONS The cruise control allows driving at a speed between 30 - 90 MPH (48 - 144 km/h) without keeping your foot on the accelerator pedal. To turn on the cruise control, push the main switch. The CRUISE indicator light in the instrument panel comes on. To set cruising speed, accelerate the vehicle to the desired speed, push the COAST/SET switch and release it. The SET indicator light in the instrument panel comes on. Take your foot off the accelerator pedal. Your vehicle maintains the set speed. ● To pass another vehicle, depress the accelerator pedal. When you release the pedal, the vehicle returns to the previously set speed. ● The vehicle may not maintain the set speed when going up or down steep hills. If this happens, drive without the cruise control. To cancel the preset speed, use one of the following three methods. ● Push the CANCEL button; the SET indicator light in the instrument panel goes out. ● Tap the brake pedal; the SET indicator light goes out. ● Turn the main switch off. Both the CRUISE indicator light and SET indicator light in the instrument panel go out. 5-12 Starting and driving Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X BREAK-IN SCHEDULE The cruise control is automatically canceled and the SET light in the instrument panel goes out if: ● you depress the brake pedal while pushing the ACCEL/RES or SET/COAST switch. The preset speed is deleted from memory. ● the vehicle slows down more than 8 MPH (13 km/h) below the set speed. ● you move the shift selector lever to N (Neutral). To reset at a faster cruising speed, use one of the following three methods. ● Depress the accelerator pedal. When the vehicle attains the desired speed, push and release the COAST/SET switch. ● Push and hold the RES/ACCEL switch. When the vehicle attains the speed you desire, release the switch. ● Push and release the RES/ACCEL switch. Each time you do this, the set speed increases by about 1 MPH (1.6 km/h). ● Push and hold the COAST/SET switch. Release the switch when the vehicle slows to the desired speed. ● Push and release the COAST/SET switch. Each time you do this, the set speed decreases by about 1 MPH (1.6 km/h). To resume the preset speed, push and release the RES/ACCEL switch. The vehicle returns to the last set cruising speed when the vehicle speed is over 30 MPH (48 km/h). CAUTION During the first 1,200 miles (2,000 km), follow these recommendations to obtain maximum engine performance and ensure the future reliability and economy of your new vehicle. Failure to follow these recommendations may result in shortened engine life and reduced engine performance. ● Avoid driving for long periods at constant speed, either fast or slow, and do not run the engine over 4,000 rpm. ● Do not accelerate at full throttle in any gear. ● Avoid quick starts. ● Avoid hard braking as much as possible. ● Do not tow a trailer for the first 500 miles (800 km). Your engine, axle or other parts could be damaged. To reset at a slower cruising speed, use one of the following three methods. ● Lightly tap the brake pedal. When the vehicle attains the desired speed, push the COAST/SET switch and release it. Starting and driving 5-13 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X INCREASING FUEL ECONOMY ● Accelerate slowly and smoothly. Maintain cruising speeds with a constant accelerator position. ● Drive at moderate speeds on the highway. Driving at high speed lowers fuel economy. ● Avoid unnecessary stopping and braking. Maintain a safe distance behind other vehicles. ● Use a proper gear range which suits road conditions. On level roads, shift into high gear as soon as possible. ● Avoid unnecessary engine idling. ● Keep your engine tuned up. ● Follow the recommended periodic maintenance schedule. ● Keep the tires inflated to the correct pressure. Low tire pressure increases tire wear and lowers fuel economy. ● Keep the wheels in correct alignment. Improper alignment increases tire wear and lowers fuel economy. WSD0050 ● When cruising at highway speeds, it is more economical to use the air conditioner and leave the windows closed to reduce drag. ● Use the recommended viscosity engine oil. See “Engine oil and oil filter recommendation” in “Technical and consumer information” later in this manual. ● Air conditioner operation lowers fuel economy. Use the air conditioner only when necessary. 5-14 Starting and driving Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X PARKING/PARKING ON HILLS WARNING ● Do not stop or park the vehicle over flammable materials such as dry grass, waste paper or rags. They may ignite and cause a fire. ● Safe parking procedures require that both the parking brake be set and the transmission placed into P (Park). Failure to do so could cause the vehicle to move unexpectedly or roll away and result in an accident. Make sure the shift lever has been pushed as far forward as it can go and cannot be moved without depressing the foot brake pedal. ● Never leave the engine running while the vehicle is unattended. ● Do not leave children unattended inside the vehicle. They could unknowingly activate switches or controls. Unattended children could become involved in serious accidents. POWER STEERING 3. To help prevent the vehicle from rolling into traffic when parked on an incline, it is a good practice to turn the wheels as illustrated. The power assisted steering is designed to use a hydraulic pump, driven by the engine, to assist steering. A ● HEADED DOWNHILL WITH CURB: s If the engine stops or the drive belt breaks, you will still have control of the vehicle. However, much greater steering effort is needed, especially in sharp turns and at low speeds. Turn the wheels into the curb and move the vehicle forward until the curb side wheel gently touches the curb. B ● HEADED UPHILL WITH CURB: s Turn the wheels away from the curb and move the vehicle back until the curb side wheel gently touches the curb. ● HEADED UPHILL OR DOWNHILL, NO C CURB: s WARNING If the engine is not running or is turned off while driving, the power assist for the steering will not work. Steering will be much harder to operate. Turn the wheels toward the side of the road so the vehicle will move away from the center of the road if it moves. 4. Turn the ignition key to the LOCK position and remove the key. 1. Firmly apply the parking brake. 2. Move the shift selector lever to the P (Park) position. Starting and driving 5-15 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X BRAKE SYSTEM The brake system has two separate hydraulic circuits. If one circuit malfunctions, you will still have braking at two wheels. BRAKE PRECAUTIONS Vacuum assisted brakes The brake booster aids braking by using engine vacuum. If the engine stops, you can stop the vehicle by depressing the brake pedal. However, greater foot pressure on the brake pedal will be required to stop the vehicle and stopping distance will be longer. Using the brakes Avoid resting your foot on the brake pedal while driving. This will overheat the brakes, wear out the brake linings and pads faster, and reduce gas mileage. To help reduce brake wear and to prevent the brakes from overheating, reduce speed and downshift to a lower gear before going down a slope or long grade. Overheated brakes may reduce braking performance and could result in loss of vehicle control. WARNING ● While driving on a slippery surface, be careful when braking, accelerating or downshifting. Abrupt braking or accelerating could cause the wheels to skid and result in an accident. ● If the engine is not running or is turned off while driving, the power assist for the brakes will not work. Braking will be harder. Wet brakes When the vehicle is washed or driven through water, the brakes may get wet. As a result, your braking distance will be longer and the vehicle may pull to one side during braking. This procedure is described in the vehicle service manual and can be performed by a NISSAN dealer. ANTI-LOCK BRAKE SYSTEM (ABS) The anti-lock brake system controls the brakes so the wheels do not lock when braking abruptly or when braking on slippery surfaces. The system detects the rotation speed at each wheel and varies the brake fluid pressure to prevent each wheel from locking and sliding. By preventing wheel lockup, the system helps the driver maintain steering control and helps to minimize swerving and spinning on slippery surfaces. Using the system Depress the brake pedal and hold it down. To dry the brakes, drive the vehicle at a safe speed while lightly pressing the brake pedal to heat up the brakes. Do this until the brakes return to normal. Avoid driving the vehicle at high speeds until the brakes function correctly. Do not pump the brake pedal. Doing so may result in increased stopping distances. Parking brake bedding Normal operation The parking brake shoes must be “bedded down” whenever the stopping effect of the parking brake is weakened or whenever the parking brake shoes and/or drum/rotors are replaced, in order to assure the best brake performance. The anti-lock brake system does not operate at speeds below 3 - 6 MPH (5 - 10 km/h). (The speeds vary according to road conditions.) WARNING When driving, the anti-lock brake system controls the wheels so they will not lock when brak- 5-16 Starting and driving Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X ing abruptly or when braking on a slippery road. Thus, difficult steering and swerving of the vehicle due to locked wheels is minimized. The system detects the wheel rotation rate and electronically controls the pressure applied to each brake. Slight vibration on the brake pedal accompanied by noise usually occurs while the ABS system is operating. Such vibration and noise encountered during abrupt braking is not a problem, but indicates that the system is functioning properly. However, the pulsation may indicate that road conditions are hazardous and extra care is required while driving. Self-test feature The anti-lock brake system consists of electronic sensors and hydraulic solenoids controlled by a computer. The computer has a built-in diagnostic feature that tests the system each time you start the engine and move the vehicle at a low speed in forward or reverse. When the self-test occurs, you may hear a ‘‘clunk’’ noise and/or feel a pulsation in the brake pedal. This is normal and is not an indication of any malfunction. If the computer senses any malfunction, it switches the anti-lock brake system off and turns on the ABS brake warning light on the instrument panel. The brake system then operates normally, but without antilock assistance. If a malfunction occurs in the system, the antilock function will not operate, but the standard vehicle brake system will continue to operate normally. The ABS brake warning light will then come on. If the light comes on during the self-test or while driving, take the vehicle to a NISSAN dealer for repair. WARNING ● The anti-lock brake system is a sophisticated device, but it cannot prevent accidents resulting from careless or dangerous driving techniques. It can help maintain vehicle control during braking on slippery surfaces, but remember that the stopping distance on slippery surfaces will be longer than on normal surfaces even with the anti-lock brake system. Stopping distances may also be longer on rough, gravel or snow covered roads, or if you are using tire chains. Tire type and condition may also affect braking effectiveness. Always maintain a safe distance from the vehicle in front of you. Ultimately, the responsibility for safety of self and others rests in the hands of the driver. ● Tire type and condition of tires may also affect braking effectiveness. ● When replacing tires, install the specified size of tires on all four wheels. ● When installing a spare tire, make sure it is the proper size and type as specified on the tire placard. For tire placard location information, refer to “Tire placard” in the “Technical and consumer information” section of this manual. ● Refer to “Wheels and tires” in the “Maintenance and do-it-yourself” section of this manual. Starting and driving 5-17 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X TRACTION CONTROL SYSTEM (TCS) When accelerating on slippery surfaces the tire may spin or slip. With the vehicle traction control system, sensors detect these movements and control the braking and engine output to help improve vehicle stability while accelerating. ● When the traction control system is operating, the slip indicator in the instrument panel blinks. ● If the slip indicator blinks, the vehicle is under slippery conditions. Be sure to drive carefully. See “Slip indicator light” and “Traction control off indicator light” in the “Instruments and controls” section of this manual. ● If a malfunction occurs in the system, the and indicator lights come on in the meter panel. As long as these warning lights are on, the traction control function is canceled. The vehicle will behave like a vehicle without the system. WARNING ● The traction control system is designed to help improve driving stability but does not prevent accidents due to abrupt steering operation at high speeds or by careless or dangerous driving techniques. Reduce vehicle speed and be especially careful when driving and cornering on slippery surfaces and always drive carefully. ● If brake related parts such as brake pads, rotors and calipers are not standard equipment or are extremely deteriorated, the traction control system may not operate properly and the indicator light may come on. ● When driving on extremely inclined surfaces such as higher banked corners, the traction control system may not opindicator erate properly and the light may come on. Do not drive on these types of roads. ● If wheels or tires other than the recommended ones are used, the traction control system may not operate properly and the indicator light may come on. ● The traction control system is not a substitute for winter tires or tire chains on a snow covered road. ● Do not modify the vehicle’s suspension. If suspension parts such as shock absorbers, struts, springs and bushings are not standard equipment or are extremely deteriorated, the traction control system may not operate properly and the indicator light may come on. 5-18 Starting and driving Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X VEHICLE DYNAMIC CONTROL (VDC) SYSTEM (if so equipped) When accelerating or driving on slippery surfaces, the tires may spin or slide. With the Vehicle Dynamic Control (VDC) system, sensors detect these movements and control the braking and engine output to help improve vehicle stability. ● When the vehicle dynamic control (VDC) system is operating, the slip indicator in the instrument panel blinks. ● When only the traction control system (TCS) portion of the vehicle dynamic control system is operating, the slip indicator will also blink. ● If the slip indicator blinks, the road conditions are slippery. Be sure to adjust your speed and driving to these conditions. See “Slip indicator light”, and “Vehicle dynamic control off indicator light” in the “Instruments and controls” section. ● Indicator light If malfunction occurs in the system, the and indicator lights come on in the instrument panel. As long as these warning lights are on, the traction control function is canceled. The VDC system uses an Active Brake Limited Slip (ABLS) system to improve vehicle traction. The ABLS system works when one of the driving wheels is spinning on a slippery surface. The ABLS system brakes the spinning wheel which distributes the driving power to the other drive wheel. If the vehicle is operated with the vehicle dynamic control system off, all VDC and TCS functions will be turned off. The ABLS system and ABS will still operate with the VDC system OFF. If the ABLS system or the ABS is activated, the slip indicator light will blink and you may hear a clunk noise and/or feel a pulsation in the brake pedal. This is normal. While the VDC system is operating, you may feel a pulsation in the brake pedal and hear a noise or vibration from under the hood. This is normal and indicates that the VDC system is working properly. The computer has a built in diagnostic feature that tests the system each time you start the engine and move the vehicle forward or in reverse at a slow speed. When the self-test occurs, you may hear a clunk noise and/or feel a pulsation in the brake pedal. This is normal and is not an indication of a malfunction. WARNING ● The vehicle dynamic control system is designed to help improve driving stability but does not prevent accidents due to abrupt steering operation at high speeds or by careless or dangerous driving techniques. Reduce vehicle speed and be especially careful when driving and cornering on slippery surfaces and always drive carefully. ● If brake related parts such as brake pads, rotors and calipers are not standard equipment or are extremely deteriorated, the vehicle dynamic control system may not operate properly and the vehicle dynamic control off indicator light may come on. ● Do not modify the vehicle’s suspension. If suspension parts such as shock absorbers, struts, springs, stabilizer bars and bushings are not NISSAN approved for your vehicle or are extremely deteriorated the vehicle dynamic control system may not operate properly. This could adversely affect vehicle handling performance, and the vehicle dynamic control off indicator light may come on. Starting and driving 5-19 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X REAR SONAR SYSTEM (if so equipped) ● When driving on extremely inclined surfaces such as higher banked corners, the vehicle dynamic control system may not operate properly and the vehicle dynamic control off indicator light may come on. Do not drive on these types of roads. ● The system is designed as an aid to the driver in detecting large stationary objects to help avoid damaging the vehicle. The system may not detect smaller objects, particularly those close to the ground. ● If your vehicle sustains damage to the rear bumper fascia, leaving it misaligned or bent, the sensing zone may be altered causing inaccurate measurement of obstacles or false alarms. ● If wheels or tires other than the recommended ones are used, the vehicle dynamic control system may not operate properly and the vehicle dynamic control off indicator light may come on. ● The vehicle dynamic control system is not a substitute for winter tires or tire chains on a snow covered road. LSD0088 WARNING ● Always turn and look back before backing. The RSS is not a substitute for proper backing procedures. ● Read and understand the limitations of the rear sonar system as contained in this section. Inclement weather may affect the function of the RSS; this may include reduced performance or a false activation. ● This system is not designed to prevent contact with small or moving objects. The Rear Sonar System (RSS) sounds a tone to warn the driver of obstacles near the rear bumper when R (Reverse) is selected. The system may not detect objects at speeds above 3 mph (5 km/h) and may not detect certain angular or moving objects. The RSS detects obstacles up to 6 ft. (1.8 meters) from the rear bumper with a decreased coverage area at the outer corners of the bumper, (refer to the illustration for approximate zone coverage areas). As you move closer to the obstacle, the rate of the tone increases. When the obstacle is less than 10 in. (25.0 cm) away, the tone will sound continuously. If the RSS detects a stationary or receding object further than 10 in. (25.0 cm) from the side of the vehicle, the tone will 5-20 Starting and driving Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X COLD WEATHER DRIVING sound for only three seconds. Once the system detects an object approaching, the tone will sound again. The RSS automatically turns on when the gear selector is placed in R (Reverse) and the ignition is ON. The RSS OFF switch on the instrument panel allows the driver to turn the RSS on and off. To turn the RSS off, the ignition must be ON, and the gear selector in R (Reverse). An indicator light on the switch will illuminate when the system is turned off. If the indicator light illuminates when the RSS is not turned off, it may indicate a failure in the RSS. Keep the RSS sensors (located on the rear bumper fascia) free from snow, ice and large accumulations of dirt (do not clean the sensors with sharp objects). If the sensors are covered, it will affect the accuracy of the RSS. FREEING A FROZEN DOOR LOCK To prevent a door lock from freezing, apply deicer through the key hole. If the lock becomes frozen, heat the key before inserting it into the key hole. ANTI-FREEZE In the winter when it is anticipated that the temperature will drop below 32°F (0°C), check the anti-freeze to assure proper winter protection. For details, see ‘‘Engine cooling system’’ in the ‘‘Maintenance and do-it-yourself’’ section of this manual. BATTERY If the battery is not fully charged during extremely cold weather conditions, the battery fluid may freeze and damage the battery. To maintain maximum efficiency, the battery should be checked regularly. For details, see ‘‘Battery’’ in the ‘‘Maintenance and do-it-yourself’’ section of this manual. DRAINING OF COOLANT WATER If the vehicle is to be left outside without antifreeze, drain the cooling system, including the engine block. Refill before operating the vehicle. For details, see ‘‘Changing engine coolant’’ in the ‘‘Maintenance and do-it-yourself’’ section of this manual. TIRE EQUIPMENT 1. SUMMER tires have a tread designed to provide superior performance on dry pavement. However, the performance of these tires will be substantially reduced in snowy and icy conditions. If you operate your vehicle on snowy or icy roads, NISSAN recommends the use of MUD & SNOW or ALL SEASON TIRES on all four wheels. Please consult a NISSAN dealer for the tire type, size, speed rating and availability information. 2. For additional traction on icy roads, studded tires may be used. However, some U.S. states and Canadian provinces prohibit their use. Check local, state and provincial laws before installing studded tires. Skid and traction capabilities of studded snow tires on wet or dry surfaces may be poorer than that of non-studded snow tires. 3. Tire chains may be used. Use of tire chains may be prohibited according to location. Check the local laws before installing tire chains. When installing tire chains, make sure they are of proper size for Starting and driving 5-21 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X the tires on your vehicle and are installed according to the chain manufacturer’s suggestions. Use only SAE Class “S” chains. Class “S” chains are used on vehicles with restricted tire to vehicle clearance. Vehicles that can use Class “S” chains are designed to meet the minimum clearances between the tire and the closest vehicle suspension or body component required to accommodate the use of a winter traction device (tire chains or cables). The minimum clearances are determined using the factory equipped tire size. Other types may damage your vehicle. Use chain tensioners when recommended by the tire chain manufacturer to ensure a tight fit. Loose end links of the tire chain must be secured or removed to prevent the possibility of whipping action damage to the fenders or underbody. If possible, avoid fully loading your vehicle when using tire chains. In addition, drive at a reduced speed. Otherwise, your vehicle may be damaged and/or vehicle handling and performance may be adversely affected. SPECIAL WINTER EQUIPMENT Never install tire chains on spare tires. Do not use tire chains on dry roads. ● Whatever the condition, drive with caution. Accelerate and slow down with care. If accelerating or downshifting too fast, the drive wheels will lose even more traction. It is recommended that the following items be carried in the vehicle during winter: ● A scraper and stiff-bristled brush to remove ice and snow from the windows and wiper blades. ● A sturdy, flat board to be placed under the jack to give it firm support. ● A shovel to dig the vehicle out of snowdrifts. ● Extra window washer fluid to refill the reservoir tank. DRIVING ON SNOW OR ICE WARNING ● Wet ice (32°F, 0°C and freezing rain), very cold snow or ice can be slick and very hard to drive on. The vehicle will have much less traction or “grip” under these conditions. Try to avoid driving on wet ice until the road is salted or sanded. ● Allow more stopping distance under these conditions. Braking should be started sooner than on dry pavement. ● Allow greater following distances on slippery roads. ● Watch for slippery spots (glare ice). These may appear on an otherwise clear road in shaded areas. If a patch of ice is seen ahead, brake before reaching it. Try not to brake while on the ice, and avoid any sudden steering maneuvers. ● Do not use the cruise control on slippery roads. ● Snow can trap dangerous exhaust gases under your vehicle. Keep snow clear of the exhaust pipe and from around your vehicle. 5-22 Starting and driving Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X 6 In case of emergency Flat tire . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-2 Low tire pressure warning system . . . . . . . . . . . . . . . . 6-2 Changing a flat tire . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-2 Jump starting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-7 Push starting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-9 If your vehicle overheats . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-9 Towing your vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-10 Towing recommended by NISSAN . . . . . . . . . . . . . . 6-11 Vehicle recovery (freeing a stuck vehicle) . . . . . . . . . 6-12 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X FLAT TIRE LOW TIRE PRESSURE WARNING SYSTEM This vehicle is equipped with the low tire pressure warning system, which displays the pressure of each tire independently (except the spare tire) on the display screen by sending a signal from a sensor that is installed in each wheel. If the vehicle is being driven with low tire pressure (lower than 28 psi, 193 kPa), the low tire pressure warning system will activate and warn you of it by the low tire pressure warning light. This system will activate only when the vehicle is driven at speeds above 20 MPH (32 km/h). For more details, please refer to “Warning/indicator lights and audible reminders” in the “Instruments and controls” section, “Tire pressure information” in the “Display screen, heater, air conditioner and audio systems” section and “Low tire pressure warning system” in the “Starting and driving” section. WARNING CHANGING A FLAT TIRE ● If the low tire pressure warning light flashes while driving, avoid sudden steering maneuvers or abrupt braking, reduce vehicle speed, pull off the road to a safe location and stop the vehicle as soon as possible. Serious vehicle damage could occur and may lead to an accident and could result in serious personal injury. Check the tire pressure for all four tires. Adjust the tire pressure to the recommended COLD tire pressure shown on the Tire and Loading Information label to turn the low tire pressure warning light OFF. If you have a flat tire, replace it with a spare tire as soon as possible. If you have a flat tire, follow the instructions below. ● When a spare tire is mounted or a wheel is replaced, tire pressure will not be indicated and the low tire pressure warning system will not function. Contact your NISSAN dealer as soon as possible for tire replacement and/or system resetting. 6. Have all passengers get out of the vehicle and stand in a safe place, away from traffic and clear of the vehicle. ● Do not inject any tire liquid or aerosol tire sealant into the tires, as this may cause a malfunction of the tire pressure sensors. Stopping the vehicle 1. Safely move the vehicle off the road and away from traffic. 2. Turn on the hazard warning flashers. 3. Park on a level surface and apply the parking brake. Shift the transmission into P (Park). 4. Turn off the engine. 5. Raise the hood to warn other traffic and to signal professional road assistance personnel that you need assistance. WARNING ● Make sure the parking brake is securely applied and the automatic transmission is shifted into P (Park). ● Never change tires when the vehicle is on a slope, ice or slippery areas. This is hazardous. 6-2 In case of emergency Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X ● Never change tires if oncoming traffic is close to your vehicle. Wait for professional road assistance. ● When a spare tire is mounted or a wheel is replaced, tire pressure will not be indicated and the low tire pressure warning system will not function. Contact your NISSAN dealer as soon as possible for tire replacement and/or system resetting. WCE0044 Blocking wheels LCE0078 Getting the spare tire and tools 1 at both the front and Place suitable blocks s back of the wheel diagonally opposite the flat tire 2 to prevent the vehicle from rolling when it is s jacked up. WARNING Be sure to block the wheel as the vehicle may move and result in personal injury. 1. Tip up the passenger side second row captain’s chair. Refer to “Tip up for easy entry to third row” in the “Safety — seats, seat belts and supplemental air bags” section of this owner’s manual. 2. Lift up the floor carpeting and remove the jack. In case of emergency 6-3 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X 5. Turn the retainer counterclockwise and remove the spare tire. Removing wheel cover (if so equipped) CAUTION Do not use your hands to pry off wheel caps or wheel covers. Doing so could result in personal injury. Use caution not to scratch the wheel cover or wheel surface. WSD0085 Jacking up vehicle and removing the damaged tire WARNING ● Never get under the vehicle while it is supported only by the jack. LCE0079 3. Move both front seats as forward as possible. 1 . Remove the 4. Lift up the floor carpeting s 2 and jack tool kit. spare tire cover s ● Use only the jack provided with your vehicle to lift the vehicle. Do not use the jack provided with your vehicle on other vehicles. The jack is designed for lifting only your vehicle during a tire change. 6-4 In case of emergency Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X ● Use the correct jack-up points. Never use any other part of the vehicle for jack support. ● Never jack up the vehicle more than necessary. ● Never use blocks on or under the jack. ● Do not start or vehicle is on the vehicle to move. for vehicles differentials. run the engine while jack. It may cause the This is especially true with limited slip ● Do not allow passengers to stay in the vehicle while it is on the jack. ● Never run the engine with a wheel(s) off the ground. It may cause the vehicle to move. WCE0081 Always refer to the proper illustrations for the correct placement and jack-up points for your specific vehicle model and jack type. Carefully read the caution label attached to the jack body and the following instructions. 1. Loosen each wheel nut one or two turns by turning counterclockwise with the wheel nut wrench. Do not remove the wheel nuts until the tire is off the ground. 2. Place the jack directly under the jack-up point as illustrated so the top of the jack contacts the vehicle at the jack-up point. Align the jack head between the two notches in the front or the rear as shown. Also fit the groove of the jack head between the notches as shown. The jack should be used on firm and level ground. 3. To lift the vehicle, securely hold the jack lever and rod with both hands. Carefully raise the vehicle until the tire clears the ground. Remove the wheel nuts, and then remove the tire. In case of emergency 6-5 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X 4. Lower the vehicle slowly until the tire touches the ground. Then, with the wheel nut wrench, tighten the wheel nuts securely A,s B,s C,s D, in the sequence illustrated (s E ). Lower the vehicle completely. s WARNING ● Incorrect wheel nuts or improperly tightened wheel nuts can cause the wheel to become loose or come off. This could cause an accident. WCE0056 Installing the spare tire The spare tire is designed for emergency use. See specific instructions under the heading “Wheels and tires” in the “Maintenance and do-it-yourself” section of this manual. 1. Clean any mud or dirt from the surface between the wheel and hub. 2. Carefully put the spare tire on and tighten the wheel nuts finger tight. 3. With the wheel nut wrench, tighten wheel nuts alternately and evenly as illustrated until they are tight. ● Do not use oil or grease on the wheel studs or nuts. This could cause the nuts to become loose. Retighten the wheel nuts after the vehicle has been driven for 600 miles (1,000 km) (also in cases of a flat tire, etc.). As soon as possible, tighten the wheel nuts to the specified torque with a torque wrench. Wheel nut tightening torque: 83 ft-lb (112 N·m) The wheel nuts must be kept tightened to specification at all times. It is recommended that wheel nuts be tightened to specifications at each lubrication interval. Adjust tire pressure to the COLD pressure. COLD pressure: After vehicle has been parked for three hours or more or driven less than 1 mile (1.6 km). COLD tire pressures are shown on the Tire and Loading Information label affixed to the driver side center pillar. After adjusting tire pressure to the COLD tire pressure, the display of the tire pressure information may show higher pressure than the COLD tire pressure after the vehicle has been driven more than 1 mile (1.6 km). This is because the tire pressurizes as the tire temperature rises. This does not indicate a system malfunction. 5. Securely store the flat tire and jacking equipment in the vehicle. WARNING ● Always make sure that the spare tire and jacking equipment are properly secured after use. Such items can become dangerous projectiles in an accident or sudden stop. ● The spare tire is designed for emergency use. See specific instructions under the heading “Wheels and tires” in the “Maintenance and do-it-yourself” section of this manual. 6-6 In case of emergency Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X JUMP STARTING To start your engine with a booster battery, the instructions and precautions below must be followed. WARNING ● If done incorrectly, jump starting can lead to a battery explosion, resulting in severe injury or death. It could also damage your vehicle. ● Explosive hydrogen gas is always present in the vicinity of the battery. Keep all sparks and flames away from the battery. ● Whenever working on or near a battery, always wear suitable eye protectors (for example, goggles or industrial safety spectacles) and remove rings, metal bands, or any other jewelry. Do not lean over the battery when jump starting. ● Do not attempt to jump start a frozen battery. It could explode and cause serious injury. ● Your vehicle has an automatic engine cooling fan. It could come on at any time. Keep hands and other objects away from it. ● Do not allow battery fluid to come into contact with eyes, skin, clothing or painted surfaces. Battery fluid is a corrosive sulfuric acid solution which can cause severe burns. If the fluid should come into contact with anything, immediately flush the contacted area with water. ● Keep battery out of the reach of children. ● The booster battery must be rated at 12 volts. Use of an improperly rated battery can damage your vehicle. In case of emergency 6-7 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X ● Make sure the jumper cables do not touch moving parts in the engine compartment and that the cable clamps do not contact any other metal. 5. Start the engine of the booster vehicle and let it run for a few minutes. 6. Keep the engine speed of the booster vehicle at about 2,000 rpm, and start the engine of the vehicle being jump started. CAUTION WCE0054 WARNING Always follow the instructions below. Failure to do so could result in damage to the charging system and cause personal injury. 1. If the booster battery is in another vehicle, position the two vehicles to bring their batteries near each other. Do not allow the two vehicles to touch. 2. Apply the parking brake. Shift the transmission into P (Park). Switch off all unnecessary electrical systems (lights, heater, air conditioner, etc.). 3. Remove vent caps on the battery (if so equipped). Cover the battery with an old cloth to reduce explosion hazard. 4. Connect jumper cables in the sequence ilA,s B,s C,s D ). lustrated (s CAUTION ● Always connect positive (1) to positive (1) and negative (2) to body ground (for example, strut mounting bolt, engine lift bracket, etc.) — not to the battery. Do not keep the starter motor engaged for more than 10 seconds. If the engine does not start right away, turn the key off and wait 3 to 4 seconds before trying again. 7. After starting the engine, carefully disconnect the negative cable and then the positive cable. 8. Replace the vent caps (if so equipped). Be sure to dispose of the cloth used to cover the vent holes as it may be contaminated with corrosive acid. 6-8 In case of emergency Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X PUSH STARTING WARNING ● Automatic transmission models cannot be push-started or tow-started. This may cause transmission or other vehicle damage. IF YOUR VEHICLE OVERHEATS If your vehicle is overheating (indicated by an extremely high temperature gauge reading), or if you feel a lack of engine power, detect abnormal noise, etc. take the following steps. WARNING ● Three-way catalyst equipped models should not be started by pushing. The three-way catalyst may be damaged. ● Do not continue to drive if your vehicle overheats. Doing so could cause engine damage or a vehicle fire. ● Never try to start the vehicle by towing it. When the engine starts, the forward surge could cause the vehicle to collide with the tow vehicle. ● To avoid the danger of being scalded, never remove the radiator cap while the engine is still hot. When the radiator cap is removed, pressurized hot water will spurt out, possibly causing serious injury. ● Do not open the hood if steam is coming out. 1. Move the vehicle safely off the road, apply the parking brake and move the shift lever to P (Park). Do not stop the engine. 2. Turn off the air conditioner. Open all the windows, move the heater or air conditioner temperature control to maximum hot and fan control to high speed. 3. Get out of the vehicle. Look and listen for steam or coolant escaping from the radiator before opening the hood. (If steam or coolant is escaping, turn off the engine.) Do not open the hood further until no steam or coolant can be seen. 4. Open the engine hood. WARNING If steam or water is coming from the engine, stand clear to prevent getting burned. 5. Visually check drive belts for damage or looseness. Also check if the cooling fan is running. The radiator hoses and radiator should not leak water. If coolant is leaking, the water pump belt is missing or loose, or the cooling fan does not run, stop the engine. WARNING Be careful not to allow your hands, hair, jewelry or clothing to come into contact with, or get caught in, engine belts or the engine cooling fan. The engine cooling fan can start at any time when the coolant temperature is high. In case of emergency 6-9 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X TOWING YOUR VEHICLE 6. After the engine cools down, check the coolant level in the reservoir tank with the engine running. Add coolant to the reservoir tank if necessary. Have your vehicle repaired at a NISSAN dealer. When towing your vehicle, all State (Provincial in Canada) and local regulations for towing must be followed. Incorrect towing equipment could damage your vehicle. Towing instructions are available from a NISSAN dealer. Local service operators are generally familiar with the applicable laws and procedures for towing. To assure proper towing and to prevent accidental damage to your vehicle, NISSAN recommends having a service operator tow your vehicle. It is advisable to have the service operator carefully read the following precautions: For information about towing your vehicle behind a recreational vehicle (RV), refer to “Flat towing” in the “Technical and consumer information” section of this manual. WARNING ● Never ride in a vehicle that is being towed. ● Never get under your vehicle after it has been lifted by a tow truck. CAUTION ● When towing, make sure that the transmission, axles, steering system and powertrain are in working condition. If any unit is damaged, dollies must be used. ● Always attach safety chains before towing. 6-10 In case of emergency Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X ● Turn the ignition key to the OFF position, and secure the steering wheel in a straight-ahead position with a rope or similar device. Never secure the steering wheel by turning the ignition key to the LOCK position. This may damage the steering lock mechanism. ● Move the gearshift lever to the N (Neutral) position. WSD0087 ● When towing automatic with the rear wheels on the ground (if you do not use towing dollies): Always release the parking brake. CAUTION WSD0086 TOWING RECOMMENDED BY NISSAN NISSAN recommends that your vehicle be towed with the driving (front) wheels off the ground or place the vehicle on a flat bed truck as illustrated. ● Never tow automatic transmission models with the front wheels on the ground or four wheels on the ground (forward or backward), as this may cause serious and expensive damage to the transmission. If it is necessary to tow the vehicle with the rear wheels raised always use towing dollies under the front wheels. ● When towing with the front wheels on towing dollies: In case of emergency 6-11 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X CAUTION ● Use the towing hook only, not other parts of the vehicle. Otherwise, the vehicle body will be damaged. ● Use the towing hook only to free a vehicle stuck in sand, snow, mud, etc. Never tow the vehicle for a long distance using only the towing hook. LCE0080 VEHICLE RECOVERY (freeing a stuck vehicle) WARNING ● Stand clear of a stuck vehicle. ● Do not spin your tires at high speed. This could cause them to explode and result in serious injury. Parts of your vehicle could also overheat and be damaged. ● The towing hook is under tremendous force when used to free a stuck vehicle. Always pull the cable straight out from the front or rear of the vehicle. Never pull the hook at an angle. ● Pulling devices should be routed so they do not touch any part of the suspension, steering, brake or cooling systems. ● Pull devices such as ropes or canvas straps are not recommended for use in vehicle towing or recovery. 6-12 In case of emergency Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X 7 Appearance and care Cleaning exterior . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-2 Washing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-2 Waxing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-2 Removing spots . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-2 Underbody . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-3 Glass . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-3 Aluminum alloy wheels . . . . . . . . . . . . . . . . . . . . . . . . . . 7-3 Chrome parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-3 Cleaning interior. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-3 Floor mats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-4 Seat belts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-4 Corrosion protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-5 Most common factors contributing to vehicle corrosion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-5 Environmental factors influence the rate of corrosion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-5 To protect your vehicle from corrosion . . . . . . . . . . . . 7-5 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X CLEANING EXTERIOR In order to maintain the appearance of your vehicle, it is important to take proper care of it. To protect the paint surfaces, please wash your vehicle as soon as you can: ● after a rainfall to prevent possible damage from acid rain. ● after driving on coastal roads. ● when contaminants such as soot, bird droppings, tree sap, metal particles or bugs get on the paint surface. ● when dust or mud builds up on the surface. Whenever possible, store or park your vehicle inside a garage or in a covered area. When it is necessary to park outside, park in a shady area or protect the vehicle with a body cover. Be careful not to scratch the paint surface when putting on or removing the body cover. WASHING Wash dirt off with a wet sponge and plenty of water. Clean the vehicle thoroughly using a mild soap, a special vehicle soap or general purpose dishwashing liquid mixed with clean, lukewarm (never hot) water. CAUTION ● Do not wash the vehicle with strong household soap, strong chemical detergents, gasoline or solvents. ● Do not wash the vehicle in direct sunlight or while the vehicle body is hot, as the surface may become water-spotted. ● Avoid using tight-napped or rough cloths, such as washing mitts. Care must be taken when removing caked-on dirt or other foreign substances so the paint surface is not scratched or damaged. Rinse the vehicle thoroughly with plenty of clean water. Inside flanges, seams and folds on the doors, hatches and hood are particularly vulnerable to the effects of road salt. Therefore, these areas must be cleaned regularly. Take care that the drain holes in the lower edge of the door are open. Spray water under the body and in the wheel wells to loosen the dirt and wash away road salt. A damp chamois can be used to dry the vehicle to avoid water spots. WAXING Regular waxing protects the paint surface and helps retain new vehicle appearance. After waxing, polishing is recommended to remove built-up residue and to avoid a “weathered” appearance. A NISSAN dealer can assist you in choosing the proper product. ● Wax your vehicle only after a thorough washing. Follow the instructions supplied with the wax. ● Do not use a wax containing any abrasives, cutting compounds or cleaners that may damage the vehicle finish. ● If the surface does not polish easily, use a “road tar” remover and wax again. Machine compounding or aggressive polishing on a base coat/clear coat paint finish may dull the finish or leave swirl marks. REMOVING SPOTS Remove tar and oil spots, industrial dust, insects, and tree sap as quickly as possible from the surface of the paint to avoid lasting damage or staining. Special cleaning products are available at a NISSAN dealer or any automotive accessory store. 7-2 Appearance and care Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X CLEANING INTERIOR UNDERBODY ALUMINUM ALLOY WHEELS In areas where road salt is used in winter, it is necessary to clean the underbody regularly in order to prevent dirt and salt from building up and causing the acceleration of corrosion on the underbody and suspension. Before the winter period and again in the spring, the underseal must be checked and, if necessary, retreated. Wash the wheels regularly, especially during winter months in areas where road salt is used. If not removed, road salt could discolor the wheels. GLASS Use glass cleaner to remove smoke and dust film from the glass surfaces. It is normal for glass to become coated with a film after the vehicle is parked in the hot sun. Glass cleaner and a soft cloth will easily remove this film. CAUTION When cleaning the inside of the windows, do not use sharp-edged tools, abrasive cleaners or chlorine-based disinfectant cleaners. They could damage the electrical conductors, radio antenna elements or rear window defroster elements. CHROME PARTS Clean all chrome parts regularly with a nonabrasive chrome polish to maintain the finish. Occasionally remove loose dust from the interior trim, plastic parts and seats using a vacuum cleaner or soft brush. Wipe the vinyl and leather surfaces with a clean, soft cloth dampened in mild soap solution, then wipe clean with a dry, soft cloth. Before using any fabric protector, read the manufacturer’s recommendations. Some fabric protectors contain chemicals that may stain or bleach the seat material. Use a cloth dampened only with water to clean the meter and gauge lens. CAUTION ● Never use benzine, thinner or any similar material. ● Small dirt particles can be abrasive and damaging to leather surfaces and should be removed promptly. Do not use saddle soap, polishes, oils, cleaning fluids, solvents, detergents or ammonia-based cleaners as they may damage the leather’s natural finish. ● Never use fabric protectors unless recommended by the manufacturer. ● Do not use glass or plastic cleaner on meter or gauge lens covers. It may damage the lens cover. Appearance and care 7-3 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X FLOOR MATS SEAT BELTS The use of genuine NISSAN floor mats can extend the life of your vehicle carpet and make it easier to clean the interior. No matter what mats are used, be sure they are fitted for your vehicle and are properly positioned in the footwell to prevent interference with pedal operation. Mats should be maintained with regular cleaning and replaced if they become excessively worn. The seat belts can be cleaned by wiping them with a sponge dampened in a mild soap solution. Allow the belts to dry completely in the shade before using them. See “Seat belt maintenance” in the “Safety – Seats, seat belts and supplemental air bags” section of this manual. WARNING WAI0006 Do not allow wet seat belts to roll up in the retractor. NEVER use bleach, dye or chemical solvents to clean the seat belts, since these materials may severely weaken the seat belt webbing. Floor mat positioning aid (driver’s side only) This vehicle includes a front floor mat bracket to act as a floor mat positioning aid. NISSAN floor mats have been specially designed for your vehicle model. The driver’s side floor mat has a grommet hole incorporated in it. Position the mat by placing the floor mat bracket hook through the floor mat grommet hole while centering the mat in the footwell. Periodically check to make certain the mats are properly positioned. 7-4 Appearance and care Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X CORROSION PROTECTION MOST COMMON FACTORS CONTRIBUTING TO VEHICLE CORROSION 1. The accumulation of moisture-retaining dirt and debris in body panel sections, cavities, and other areas. 2. Damage to paint and other protective coatings caused by gravel and stone chips or minor traffic accidents. ENVIRONMENTAL FACTORS INFLUENCE THE RATE OF CORROSION Moisture ● where atmospheric pollution exists. ● where road salt is used. Temperature High temperatures accelerate the rate of corrosion to those parts which are not well ventilated. Air pollution Industrial pollution, the presence of salt in the air in coastal areas, or heavy road salt use accelerates the corrosion process. Road salt also accelerates the disintegration of paint surfaces. TO PROTECT YOUR VEHICLE FROM CORROSION Accumulation of sand, dirt and water on the vehicle body underside can accelerate corrosion. Wet floor coverings will not dry completely inside the vehicle, and should be removed for drying to avoid floor panel corrosion. ● Wash and wax your vehicle often to keep the vehicle clean. Relative humidity ● Keep drain holes at the bottom of the doors open to avoid water accumulation. Corrosion will be accelerated: ● in areas of high relative humidity. ● in areas where the temperatures stay above freezing. ● Always check for minor damage to the paint and repair it as soon as possible. CAUTION ● NEVER remove dirt, sand or other debris from the passenger compartment by washing it out with a hose. Remove dirt with a vacuum cleaner or broom. ● Never allow water or other liquids to come in contact with electronic components inside the vehicle as this may damage them. Chemicals used for road surface de-icing are extremely corrosive. They accelerate corrosion and deterioration of underbody components such as the exhaust system, fuel and brake lines, brake cables, floor pan and fenders. In winter, the underbody must be cleaned periodically. For additional protection against rust and corrosion, which may be required in some areas, consult a NISSAN dealer. ● Check the underbody for accumulation of sand, dirt or salt. If present, wash with water as soon as possible. Appearance and care 7-5 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X MEMO 7-6 Appearance and care 8 Maintenance and do-it-yourself Maintenance requirements. . . . . . . . . . . . . . . . . . . . . . . . . . 8-2 General maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-2 Explanation of general maintenance items . . . . . . . . . 8-2 Maintenance precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-5 Engine compartment check locations . . . . . . . . . . . . . . . . 8-6 Engine cooling system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-7 Checking engine coolant level . . . . . . . . . . . . . . . . . . . 8-7 Changing engine coolant . . . . . . . . . . . . . . . . . . . . . . . . 8-8 Engine oil. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-8 Checking engine oil level . . . . . . . . . . . . . . . . . . . . . . . . 8-8 Changing engine oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-9 Changing engine oil filter . . . . . . . . . . . . . . . . . . . . . . . 8-10 4-speed automatic transmission fluid . . . . . . . . . . . . . . . 8-11 Temperature conditions for checking. . . . . . . . . . . . . 8-11 5-speed automatic transmission fluid . . . . . . . . . . . . . . . 8-12 Power steering fluid. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-13 Brake fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-13 Brake fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-14 Window washer fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-14 Window washer fluid reservoir . . . . . . . . . . . . . . . . . . 8-14 Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-15 Jump starting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-16 Drive belts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-16 Spark plugs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-17 Replacing spark plugs . . . . . . . . . . . . . . . . . . . . . . . . . 8-17 Air cleaner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-18 In-cabin microfilter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-18 Windshield wiper blades . . . . . . . . . . . . . . . . . . . . . . . . . . 8-19 Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-19 Replacing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-19 Parking brake and brake pedal . . . . . . . . . . . . . . . . . . . . . 8-22 Checking parking brake . . . . . . . . . . . . . . . . . . . . . . . . 8-22 Checking brake pedal. . . . . . . . . . . . . . . . . . . . . . . . . . 8-22 Brake booster . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-23 Fuses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-23 Engine compartment . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-23 Passenger compartment . . . . . . . . . . . . . . . . . . . . . . . 8-24 Keyfob battery replacement . . . . . . . . . . . . . . . . . . . . . . . . 8-25 Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-26 Headlights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-26 Fog lights (if so equipped) . . . . . . . . . . . . . . . . . . . . . . 8-26 Exterior and interior lights. . . . . . . . . . . . . . . . . . . . . . . 8-27 Wheels and tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-31 Tire pressure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-31 Tire labeling. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-33 Types of tires. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-36 Tire chains . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-36 Changing wheels and tires . . . . . . . . . . . . . . . . . . . . . 8-37 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X MAINTENANCE REQUIREMENTS Your new NISSAN has been designed to have minimum maintenance requirements with longer service intervals to save you both time and money. However, some day-to-day and regular maintenance is essential to maintain your NISSAN’s good mechanical condition, as well as its emission and engine performance. It is the owner’s responsibility to make sure that the scheduled maintenance, as well as general maintenance, is performed. As the vehicle owner, you are the only one who can ensure that your vehicle receives proper maintenance. You are a vital link in the maintenance chain. Scheduled maintenance For your convenience, both required and optional scheduled maintenance items are described and listed in your “NISSAN Service and Maintenance Guide.” You must refer to that guide to ensure that necessary maintenance is performed on your NISSAN at regular intervals. General maintenance General maintenance includes those items which should be checked during normal day-to-day operation. They are essential for proper vehicle operation. It is your responsibility to perform these maintenance procedures regularly as prescribed. GENERAL MAINTENANCE Performing general maintenance checks requires minimal mechanical skill and only a few general automotive tools. These checks or inspections can be done by you, a qualified technician, or, if you prefer, a NISSAN dealer. Where to go for service If maintenance service is required or your vehicle appears to malfunction, have the systems checked and corrected by a NISSAN dealer. NISSAN technicians are well-trained specialists who are kept up-to-date with the latest service information through technical bulletins, service tips, and in-dealership training programs. They are completely qualified to work on NISSAN vehicles before they work on your vehicle, rather than after they have worked on it. You can be confident that a NISSAN dealer’s service department performs the best job to meet the maintenance requirements on your vehicle — in a reliable and economic way. During the normal day-to-day operation of the vehicle, general maintenance should be performed regularly as prescribed in this section. If you detect any unusual sounds, vibrations or smells, be sure to check for the cause or have a NISSAN dealer do it promptly. In addition, you should notify a NISSAN dealer if you think that repairs are required. When performing any checks or maintenance work, closely observe the “Maintenance precautions” later in this section. EXPLANATION OF GENERAL MAINTENANCE ITEMS Additional information on the following items with “*” is found later in this section. Outside the vehicle The maintenance items listed here should be performed from time to time, unless otherwise specified. Doors and engine hood Check that the doors and engine hood operate properly. Also ensure that all latches lock securely. Lubricate hinges, latches, latch pins, rollers and links as necessary. Make sure that the secondary latch keeps the hood from opening when the primary latch is released. 8-2 Maintenance and do-it-yourself Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X When driving in areas using road salt or other corrosive materials, check lubrication frequently. Lights* Clean the headlights on a regular basis. Make sure that the headlights, stop lights, tail lights, turn signal lights, and other lights are all operating properly and installed securely. Also check headlight aim. Road wheel nuts* When checking the tires, make sure no wheel nuts are missing, and check for any loose wheel nuts. Tighten if necessary. Tire rotation* Tires should be rotated every 7,500 miles (12,000 km). Tires* Check the pressure with a gauge often and always prior to long distance trips. If necessary, adjust the pressure in all tires, including the spare, to the pressure specified. Check carefully for damage, cuts or excessive wear. Wheel alignment and balance If the vehicle should pull to either side while driving on a straight and level road, or if you detect uneven or abnormal tire wear, there may be a need for wheel alignment. If the steering wheel or seat vibrates at normal highway speeds, wheel balancing may be needed. ● For additional information regarding tires, refer to “Important Tire Safety Information” (US) or “Tire Safety Information” (Canada) in the Warranty Information Booklet . Windshield Clean the windshield on a regular basis. Check the windshield at least every six months for cracks or other damage. Have a damaged windshield repaired by a qualified repair facility. Windshield wiper blades* Check for cracks or wear if they do not wipe properly. Inside the vehicle The maintenance items listed here should be checked on a regular basis, such as when performing periodic maintenance, cleaning the vehicle, etc. Additional information on the following items with an “*” is found later in this section. Accelerator pedal Check the pedal for smooth operation and make sure the pedal does not bind or require uneven effort. Keep the floor mat away from the pedal. Automatic transmission P (Park) position mechanism On a fairly steep hill check that your vehicle is held securely with the selector lever in the P position without applying any brakes. Brake pedal and booster* Check the pedal for smooth operation and make sure it has the proper distance under it when depressed fully. Check the brake booster function. Be certain to keep the floor mat away from the pedal. Brakes Check that the brakes do not pull the vehicle to one side when applied. Parking brake* Check that the lever has the proper travel and confirm that your vehicle is held securely on a fairly steep hill with only the parking brake applied. Seats Check seat position controls such as seat adjusters, seatback recliner, etc. to ensure they operate smoothly and all latches lock securely in every position. Check that the head restraints move up and down smoothly and the locks (if so equipped) hold securely in all latched positions. Seat belts Check that all parts of the seat belt system (for example, buckles, anchors, adjusters and retractors) operate properly and smoothly, and are installed securely. Check the belt webbing for cuts, fraying, wear or damage. Steering wheel Check for changes in the steering system, such as excessive freeplay, hard steering or strange noises. Warning lights and chimes Make sure all warning lights and chimes are operating properly. Windshield wiper and washer* Check that the wipers and washer operate properly and that the wipers do not streak. Maintenance and do-it-yourself 8-3 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X Windshield defroster Check that the air comes out of the defroster outlets properly and in sufficient quantity when operating the heater or air conditioner. Engine oil level* Check the level after parking the vehicle on a level surface with the engine off. Wait more than 10 minutes for the oil to drain back into the oil pan. Under the hood and vehicle Exhaust system Make sure there are no loose supports, cracks or holes. If the sound of the exhaust seems unusual or there is a smell of exhaust fumes, immediately have the exhaust system inspected by a NISSAN dealer. See the carbon monoxide warning in the “Starting and driving” section of this manual. The maintenance items listed here should be checked periodically (for example, each time you check the engine oil or refuel). 4–speed automatic transmission fluid level* Check the level after putting the selector lever in P with the engine idling at operating temperature. Battery* Check the fluid level in each cell. It should be between the MAX and MIN lines. Vehicles operated in high temperatures or under severe conditions require frequent checks of the battery fluid level. Brake fluid levels* Make sure that the brake fluid level is between the MIN and MAX lines on the reservoir. Engine coolant level* Check the coolant level when the engine is cold. Engine drive belts* Make sure the drive belts are not frayed, worn, cracked or oily. Fluid leaks Check under the vehicle for fuel, oil, water or other fluid leaks after the vehicle has been parked for a while. Water dripping from the air conditioner after use is normal. If you should notice any leaks or if gasoline fumes are evident, check for the cause and have it corrected immediately. Underbody The underbody is frequently exposed to corrosive substances such as those used on icy roads or to control dust. It is very important to remove these substances from the underbody, otherwise rust may form on the floor pan, frame, fuel lines and exhaust system. At the end of winter, the underbody should be thoroughly flushed with plain water, in those areas where mud and dirt may have accumulated. See the “Appearance and care” section of this manual. Windshield washer fluid* Check that there is adequate fluid in the reservoir. Power steering fluid level* and lines Check the level when the fluid is cold, with the engine off. Check the lines for proper attachment, leaks, cracks, etc. Radiator and hoses Check the front of the radiator and clean off any dirt, insects, leaves, etc., that may have accumulated. Make sure the hoses have no cracks, deformation, rot or loose connections. 8-4 Maintenance and do-it-yourself Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X MAINTENANCE PRECAUTIONS When performing any inspection or maintenance work on your vehicle, always take care to prevent serious accidental injury to yourself or damage to the vehicle. The following are general precautions which should be closely observed. WARNING ● Park the vehicle on a level surface, apply the parking brake securely and block the wheels to prevent the vehicle from moving. Move the shift selector lever to P (Park). ● Be sure the ignition key is in the OFF or LOCK position when performing any parts replacement or repairs. ● Never leave the engine or automatic transmission related component harnesses disconnected while the ignition switch is in the ON position. ● Never connect or disconnect the battery or any transistorized component while the ignition switch is in the ON position. ● Your vehicle is equipped with an automatic engine cooling fan. It may come on at any time without warning, even if the ignition key is in the OFF position and the engine is not running. To avoid injury, always disconnect the negative battery cable before working near the fan. ● If you must work with the engine running, keep your hands, clothing, hair and tools away from moving fans, belts and any other moving parts. ● It is advisable to secure or remove any loose clothing and remove any jewelry, such as rings, watches, etc. before working on your vehicle. ● Always wear eye protection whenever you work on your vehicle. serviced by a NISSAN dealer because the fuel lines are under high pressure even when the engine is off. CAUTION ● Do not work under the hood while the engine is hot. Turn the engine off and wait until it cools down. ● Avoid contact with used engine oil and coolant. Improperly disposed engine oil, engine coolant and/or other vehicle fluids can damage the environment. Always conform to local regulations for disposal of vehicle fluid. ● If you must run the engine in an enclosed space such as a garage, be sure there is proper ventilation for exhaust gases to escape. This “Maintenance and do-it-yourself” section gives instructions regarding only those items which are relatively easy for an owner to perform. ● Never get under the vehicle while it is supported only by a jack. If it is necessary to work under the vehicle, support it with safety stands. A genuine NISSAN service manual is also available. See “Owner’s Manual/Service Manual order information” in the “Technical and consumer information” section of this manual. ● Keep smoking materials, flame and sparks away from the fuel tank and battery. You should be aware that incomplete or improper servicing may result in operating difficulties or excessive emissions, and could affect warranty coverage. If in doubt about any servicing, have it done by a NISSAN dealer. ● On gasoline engine models with the multiport fuel injection (MFI) system, the fuel filter or fuel lines should be Maintenance and do-it-yourself 8-5 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X ENGINE COMPARTMENT CHECK LOCATIONS 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. Power steering fluid reservoir Engine oil filler cap Brake fluid reservoir Air cleaner Battery Fuse/fusible link box Transmission dipstick Engine oil dipstick Radiator cap Fuse block Windshield washer fluid reservoir Coolant reservoir NOTE: Engine cover removed for clarity. LII0017 8-6 Maintenance and do-it-yourself Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X ENGINE COOLING SYSTEM The engine cooling system is filled at the factory with a high-quality, year-round, anti-freeze coolant solution. The anti-freeze solution contains rust and corrosion inhibitors; therefore, additional engine cooling system additives are not necessary. WARNING ● Never remove the radiator cap when the engine is hot. Serious burns could be caused by high pressure fluid escaping from the radiator. ● The radiator is equipped with a pressure type radiator cap. To prevent engine damage, use only a genuine NISSAN radiator cap. Outside temperature down to °C °F -35 -30 Genuine NISSAN Long Life Anti-freeze Coolant or equivalent Demineralized or distilled water 50% 50% CAUTION When adding or replacing coolant, be sure to use only a Genuine NISSAN Long Life Anti-freeze Coolant (green) or equivalent with the proper mixture ratio of 50% antifreeze and 50% demineralized or distilled water. The use of other types of coolant solutions or coolant colors, such as orange, may damage the engine cooling system. LDI0350 CHECKING ENGINE COOLANT LEVEL Check the coolant level in the reservoir when the engine is cold. If the coolant level is below the MIN level, add coolant to the MAX level. If the reservoir is empty, check the coolant level in the radiator when the engine is cold. If there is insufficient coolant in the radiator, fill the radiator with coolant up to the filler opening and also add it to the reservoir up to the MAX level. If the cooling system frequently requires coolant, have it checked by a NISSAN dealer. Maintenance and do-it-yourself 8-7 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X ENGINE OIL CHANGING ENGINE COOLANT A NISSAN dealer can change the engine coolant. The service procedure can be found in the NISSAN Service Manual. Improper servicing can result in reduced heater performance and engine overheating. WARNING ● To avoid the danger of being scalded, never change the coolant when the engine is hot. ● Never remove the radiator cap when the engine is hot. Serious burns could be caused by high pressure fluid escaping from the radiator. ● Avoid direct skin contact with used coolant. If skin contact is made, wash thoroughly with soap or hand cleaner as soon as possible. LDI0351 CHECKING ENGINE OIL LEVEL 1. Park the vehicle on a level surface and apply the parking brake. 2. Start the engine and let it idle until it reaches operating temperature. ● Keep coolant out of the reach of children and pets. 3. Turn off the engine. Wait more than 10 minutes for the oil to drain back into the oil pan. Engine coolant must be disposed of properly. Check your local regulations. 4. Remove the dipstick and wipe it clean. Reinsert it all the way. LDI0352 5. Remove the dipstick again and check the oil level. It should be between the H (High) and B . This is the normal operL (Low) marks s ating oil level range. If the oil level is below A , remove the oil filler cap the L (Low) mark s and pour recommended oil through the C. opening. Do not overfill s 6. Recheck oil level with the dipstick. It is normal to add some oil between oil maintenance intervals or during the break-in period, depending on the severity of operating conditions. 8-8 Maintenance and do-it-yourself Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X If the oil filter is to be changed, remove and replace it at this time. See “Changing engine oil filter” later in this section. CAUTION Oil level should be checked regularly. Operating the engine with an insufficient amount of oil can damage the engine, and such damage is not covered by warranty. WARNING ● Prolonged and repeated contact with used engine oil may cause skin cancer. ● Try to avoid direct skin contact with used oil. If skin contact is made, wash thoroughly with soap or hand cleaner as soon as possible. WDI0216 CHANGING ENGINE OIL ● Keep used engine oil out of reach of children. CAUTION 1. Park the vehicle on a level surface and apply the parking brake. Be careful not to burn yourself. The engine oil may be hot. 2. Start the engine and let it idle until it reaches operating temperature, then turn it off. ● Waste oil must be disposed of properly. 3. Remove the oil filler cap by turning it counterclockwise. ● Check your local regulations. 4. Place a large drain pan under the drain plug. 5. Remove the drain plug with a wrench by turning it counterclockwise and completely drain the oil. 6. Clean and reinstall the drain plug and a new washer. Securely tighten the drain plug with a wrench. Do not use excessive force. Drain plug tightening torque: 22 - 29 ft-lb (29 - 39 N·m) Maintenance and do-it-yourself 8-9 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X 5. Wipe the engine oil filter mounting surface with a clean rag. 7. Refill engine with recommended oil through the oil filler opening, then install the oil filler cap securely. Be sure to remove any old gasket material remaining on the mounting surface of the engine. See “Capacities and recommended fuel/lubricants” in the “Technical and consumer information” section of this manual for drain and refill capacity. 6. Coat the gasket on the new filter with clean engine oil. The drain and refill capacity depends on the oil temperature and drain time. Use these specifications for reference only. Always use the dipstick to determine when the proper amount of oil is in the engine. 8. Start the engine. Check for leakage around the drain plug and oil filter. Correct as required. 9. Turn the engine off and wait more than 10 minutes. Check the oil level with the dipstick. Add engine oil if necessary. 7. Screw on the oil filter until a slight resistance is felt, then tighten an additional 2/3 turn. 8. Start the engine and check for leakage around the oil filter. Correct as required. WDI0218 CHANGING ENGINE OIL FILTER 9. Turn the engine off and wait more than 10 minutes. Check the oil level. Add engine oil if necessary. 1. Park the vehicle on a level surface and apply the parking brake. 2. Turn the engine off. 3. Place a large drain pan under the oil filter. 4. Loosen the oil filter with an oil filter wrench by turning it counterclockwise. Then remove the oil filter by turning it by hand. CAUTION Be careful not to burn yourself. The engine oil may be hot. 8-10 Maintenance and do-it-yourself Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X 4-SPEED AUTOMATIC TRANSMISSION FLUID ● The fluid can be checked at fluid temperatures of 86 - 122°F (30 - 50°C) using the COLD range on the dipstick after the engine is warmed up and before driving. However, the fluid should be re-checked using the HOT range. WARNING ● When the engine is running, keep hands, jewelry and clothing away from any moving parts such as the cooling fan and drive belts. ● Automatic transmission fluid is poisonous and should be stored carefully in marked containers out of the reach of children. 1. Park the vehicle on a level surface and set the parking brake. 2. Start the engine and then move the shift selector lever through each gear range, ending in P (Park). 3. Check the fluid level with the engine idling. LDI0353 TEMPERATURE CONDITIONS FOR CHECKING ● The fluid level should be checked using the HOT range on the dipstick after the following conditions have been met: – The engine should be warmed up to operating temperature. – The vehicle should be driven at least 5 minutes. – The automatic transmission fluid should be warmed to 122 - 176°F (50 - 80°C). Maintenance and do-it-yourself 8-11 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X 5-SPEED AUTOMATIC TRANSMISSION FLUID CAUTION DO NOT OVERFILL. Use ONLY Genuine Nissan Matic D ATF (Continental U.S. and Alaska) or Canada NISSAN Automatic Transmission Fluid. Dexron™ III/Mercon™ or equivalent may also be used. Outside the continental United States and Alaska contact a NISSAN dealership for more information regarding suitable fluids, including recommended brand(s) of Dexron™ III/Mercon™ automatic transmission fluid. WDI0334 4. Remove the dipstick and wipe it clean with lint-free paper. 5. Reinsert the dipstick into the dipstick tube as far as it will go. 6. Remove the dipstick and note the reading. If the automatic transmission fluid level is B , no within the normal operating range s additional fluid is required. If the fluid level is A add fluid through the dipstick tube. low s NOTE: If the vehicle has been driven for a long time at high speeds, or in city traffic in hot weather, or if it is being used to pull a trailer, the fluid level cannot be read accurately. You should wait until the fluid has cooled down (about 30 minutes) before checking fluid level. When checking or replacement is required, we recommend your NISSAN dealer for servicing. WARNING ● Use only Genuine Nissan Matic K ATF. Do not mix with other fluids. ● Using automatic transmission fluid other than Genuine Nissan Matic K ATF will cause deterioration in driveability and automatic transmission durability, and may damage the automatic transmission, which is not covered by the NISSAN new vehicle limited warranty. The specified automatic transmission fluid is also described on caution labels located in the engine compartment. 8-12 Maintenance and do-it-yourself Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X POWER STEERING FLUID BRAKE FLUID ● Recommended fluid is NISSAN PSF or equivalent. Genuine For further brake fluid specification information, refer to “Capacities and recommended fuel/lubricants” in the “Technical and consumer information” section of this manual. WARNING Use only new fluid from a sealed container. Old, inferior or contaminated fluid may damage the brake system. The use of improper fluids can damage the brake system and affect the vehicle’s stopping ability. WDI0256 The fluid level should be checked using the HOT MAX range on the power steering fluid reservoir at fluid temperatures of 122° - 176°F (50° 80°C) or using the COLD MAX range on the power steering fluid reservoir at fluid temperatures of 32° - 86°F (0° - 30°C). CAUTION Do not spill the fluid on any painted surfaces. This will damage the paint. If fluid is spilled, immediately wash the surface with water. If the fluid is below the MIN line, add Genuine NISSAN PSF fluid. Remove the cap and fill through the opening. CAUTION ● DO NOT OVERFILL. Maintenance and do-it-yourself 8-13 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X WINDOW WASHER FLUID Refill the reservoir more frequently when driving conditions require an increased amount of window washer fluid. Recommended fluid is Genuine NISSAN Windshield Washer Concentrate Cleaner & Antifreeze or equivalent. CAUTION ● Do not substitute engine anti-freeze coolant for window washer solution. This may result in damage to the paint. LDI0354 BRAKE FLUID Check the brake fluid level in the reservoir. If the fluid level is below the MIN line or the brake warning light comes on, add Genuine NISSAN Super Heavy Duty Brake Fluid or equivalent DOT 3 fluid up to the MAX line. If fluid must be added frequently, the system should be checked by a NISSAN dealer. LDI0355 WINDOW WASHER FLUID RESERVOIR Fill the window washer fluid reservoir periodically. Add window washer fluid when the light comes on. To fill the window washer fluid reservoir, lift the cap off the reservoir tank and pour the window washer fluid into the tank opening. Add a washer solvent to the washer for better cleaning. In the winter season, add a windshield washer antifreeze. Follow the manufacturer’s instructions for the mixture ratio. ● Do not fill the window washer reservoir tank with washer fluid concentrates at full strength. Some methyl alcohol based washer fluid concentrates may permanently stain the grille if spilled while filling the window washer reservoir tank. ● Pre-mix washer fluid concentrates with water to the manufacturer’s recommended levels before pouring the fluid into the window washer reservoir tank. Do not use the window washer reservoir tank to mix the washer fluid concentrate and water. 8-14 Maintenance and do-it-yourself Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X BATTERY ● Keep the battery surface clean and dry. Any corrosion should be washed off with a solution of baking soda and water. ● When working on or near a battery, always wear suitable eye protection and remove all jewelry. ● Make certain the terminal connections are clean and securely tightened. ● Battery posts, terminals and related accessories contain lead and lead compounds. Wash hands after handling. ● If the vehicle is not to be used for 30 days or longer, disconnect the negative (-) battery terminal cable to prevent discharge. ● Keep battery out of the reach of children. WARNING ● Do not expose the battery to flames or electrical sparks. Hydrogen gas generated by the battery is explosive. Do not allow battery fluid to contact your skin, eyes, fabrics or painted surfaces. After touching a battery or battery cap, do not touch or rub your eyes. Thoroughly wash your hands. If the acid contacts your eyes, skin or clothing, immediately flush with water for at least 15 minutes and seek medical attention. WDI0224 1. Remove the battery caps with a screwdriver as shown. Use a cloth to protect the battery case. ● Do not operate the vehicle if the fluid in the battery is low. Low battery fluid can cause a higher load on the battery which can generate heat, reduce battery life, and in some cases lead to an explosion. Maintenance and do-it-yourself 8-15 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X DRIVE BELTS Vehicles operated in high temperatures or under severe conditions require frequent checks of the battery fluid level. JUMP STARTING If jump starting is necessary, see “Jump starting” in the “In case of emergency” section of this manual. If the engine does not start by jump starting, the battery may have to be replaced. Contact a NISSAN dealer. WDI0226 1. 2. 3. 4. Power steering fluid pump Crankshaft Generator Air conditioner WARNING LDI0302 2. Check the fluid level in each cell If it is necessary to add fluid, add only distilled water to bring the level up to the bottom of the filler opening. Do not overfill. Be sure the ignition key is in the OFF or LOCK position. The engine could rotate unexpectedly. 1. Visually inspect each belt for signs of unusual wear, cuts, fraying or looseness. If the belt is in poor condition or is loose, have it replaced or adjusted by a NISSAN dealer. 8-16 Maintenance and do-it-yourself Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X SPARK PLUGS 2. Have the belts checked regularly for condition and tension in accordance with the maintenance schedule found in the “NISSAN Service and Maintenance Guide”. WARNING Be sure the engine and ignition switch are off and that the parking brake is engaged securely. CAUTION Be sure to use the correct socket to remove the spark plugs. An incorrect socket can damage the spark plugs. If replacement is required, please see your NISSAN dealer for assistance. WDI0005 REPLACING SPARK PLUGS Platinum-tipped spark plugs It is not necessary to replace platinum-tipped spark plugs as frequently as conventional type spark plugs because they last much longer. Follow the maintenance schedule, but do not reuse the spark plugs by cleaning or regapping. ● Always replace spark plugs with recommended or equivalent ones. Maintenance and do-it-yourself 8-17 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X AIR CLEANER WARNING ● Operating the engine with the air cleaner removed can cause you or others to be burned. The air cleaner not only cleans the air, it stops the flame if the engine backfires. If it isn’t there, and the engine backfires, you could be burned. Do not drive with the air cleaner removed, and be careful when working on the engine with the air cleaner removed. LDI0357 The air cleaner filter should not be cleaned and reused. Replace it according to the maintenance intervals shown in the “NISSAN Service and Maintenance Guide.” When replacing the filter, wipe the inside of the air cleaner filter housing and the cover with a damp cloth. IN-CABIN MICROFILTER The in-cabin microfilter restricts the entry of airborne dust and pollen particles and reduces some objectionable outside odors. The filter is located behind the glove box. Refer to the “NISSAN Service and Maintenance Guide” for change intervals. If replacement is required, see your NISSAN dealer. ● Never pour fuel into the throttle body or attempt to start the engine with the air cleaner removed. Doing so could result in serious injury. To remove the air cleaner filter: 1 s 2 s 3 s Loosen the screw. Disconnect the electrical connector. Push down on the clips and remove the air cleaner cover. Remove the air cleaner filter. 8-18 Maintenance and do-it-yourself Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X WINDSHIELD WIPER BLADES WDI0194 CLEANING If your windshield is not clear after using the windshield washer or if a wiper blade chatters when running, wax or other material may be on the blade or windshield. Clean the outside of the windshield with a washer solution or a mild detergent. Your windshield is clean if beads do not form when rinsing with clear water. Clean each blade by wiping it with a cloth soaked in a washer solution or a mild detergent. Then rinse the blades with clear water. If your windshield is still not clear after cleaning the blades and using the wiper, replace the blades. CAUTION Worn windshield wiper blades can damage the windshield and impair driver vision. 4. Insert the new wiper blade onto the wiper arm until it clicks into place. CAUTION Replace the wiper blades if they are worn. ● After wiper blade replacement, return the wiper arm to its original position; otherwise it may be damaged when the hood is opened. 1 s 2 s Lift the wiper arm away from the windshield. ● Make sure the wiper blades contact the glass; otherwise the arms may be damaged from wind pressure. 3 s Remove the wiper blade. REPLACING Push the release tab, then move the wiper blade down the wiper arm to remove. Maintenance and do-it-yourself 8-19 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X WDI0337 Be careful not to let anything get into the washer A . This may cause clogging or improper nozzle s windshield washer operation. If something gets into the nozzle, remove it with a needle or small B. pin s 8-20 Maintenance and do-it-yourself Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X LDI0356 Rear window wiper blade 1 s Lift the wiper arm away from the rear window. 2 s Push the wiper blade in and pivot until the blade becomes free. 3 s Insert a new blade onto the wiper arm and snap into place. Maintenance and do-it-yourself 8-21 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X PARKING BRAKE AND BRAKE PEDAL The front and rear disc-type brakes self-adjust every time the brake pedal is applied. WARNING See a NISSAN dealer for a brake system check if the brake pedal height does not return to normal. Brake pad wear indicators WDI0293 WDI0229 CHECKING PARKING BRAKE CHECKING BRAKE PEDAL From the released position, firmly push the parking brake down. If the number of clicks is out of the range listed, see a NISSAN dealer. With the engine running, check the distance A between the upper surface of the pedal and the metal floor. If it is out of the range shown, see a NISSAN dealer. ● 6–7 clicks under depressing force of 44 lb (196 N). Distance A: Under depression force of 110 lb (490 N) 3 1/2 in (90 mm) or more Self-adjusting brakes Your vehicle is equipped with self-adjusting brakes. The disc brake pads on your vehicle have audible wear indicators. When a brake pad requires replacement, a high pitched scraping or screeching sound will be heard when the vehicle is in motion. The noise will be heard whether or not the brake pedal is depressed. Have the brakes checked as soon as possible if the wear indicator sound is heard. Under some driving or climate conditions, occasional brake squeak, squeal or other noise may be heard. Occasional brake noise during light to moderate stops is normal and does not affect the function or performance of the brake system. Proper brake inspection intervals should be followed. For more information regarding brake inspections, see the appropriate maintenance schedule information in the “NISSAN Service and Maintenance Guide”. 8-22 Maintenance and do-it-yourself Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X FUSES BRAKE BOOSTER 3. Remove the fuse box cover by pushing the tab and lifting the cover up. Check the brake booster function as follows: 4. Remove the fuse with the fuse puller. The fuse puller is located in the center of the fuse block in the passenger compartment. 1. With the engine off, press and release the brake pedal several times. When brake pedal movement (distance of travel) remains the same from one pedal application to the next, continue on to the next step. 2. While depressing the brake pedal, start the engine. The pedal height should drop a little. 3. With the brake pedal depressed, stop the engine. Keep the pedal depressed for about 30 seconds. The pedal height should not change. 4. Run the engine for one minute without depressing the brake pedal, then turn it off. Depress the brake pedal several times. The pedal travel distance will decrease gradually with each depression as the vacuum is released from the booster. If the brakes do not operate properly, have the brakes checked by a NISSAN dealer. LDI0358 ENGINE COMPARTMENT CAUTION Never use a fuse of a higher or lower amperage rating than specified on the fuse box cover. This could damage the electrical system or cause a fire. If any electrical equipment does not come on, check for an open fuse. 1. Be sure the ignition switch and the headlight switch are OFF. 2. Open the engine hood. Maintenance and do-it-yourself 8-23 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X 4. If the fuse is open, replace it with a known good fuse. 5. Push the fuse box cover to install. 6. If a new fuse also opens, have the electrical system checked and repaired by a NISSAN dealer. WDI0200 5. If the fuse is open, replace it with a new fuse. 6. If a new fuse also opens, have the electrical system checked and repaired by a NISSAN dealer. Fusible links If the electrical equipment does not operate and fuses are in good condition, check the fusible links. If any of these fusible links are melted, replace with only genuine NISSAN parts. LDI0359 PASSENGER COMPARTMENT CAUTION Never use a fuse of a higher or lower amperage rating than specified on the fuse box cover. This could damage the electrical system or cause a fire. If any electrical equipment does not operate, check for an open fuse. 1. Be sure the ignition switch and the headlight switch are OFF. 2. Pull the fuse box cover to remove. 3. Remove the fuse with the fuse puller. 8-24 Maintenance and do-it-yourself Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X KEYFOB BATTERY REPLACEMENT 5. Press the LOCK button, then the UNLOCK button two or three times to check the keyfob operation. If the battery is removed for any reason other than replacement, perform step 5. ● An improperly disposed battery can hurt the environment. Always confirm local regulations for battery disposal. ● The keyfob is water-resistant; however, if it does get wet, immediately wipe completely dry. ● The operational range of the keyfob extends to approximately 33 ft (10 m) from the vehicle. This range may vary with conditions. FCC Notice: Changes or modifications not expressly approved by the manufacturer for compliance could void the user’s authority to operate the equipment. LPD0214 Replace the battery in the keyfob as follows: 1 s 2 s Open the lid using a coin. Remove the battery. s 3 Install a new battery with the “+” facing down. Recommended battery: Sanyo CR2025 or equivalent. 4 s Close the lid securely. This device complies with Part 15 of the FCC Rules and RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation of the device. Maintenance and do-it-yourself 8-25 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X LIGHTS HEADLIGHTS The headlight is a semi-sealed beam type which uses a replaceable headlight (halogen) bulb. If replacement is required, see your NISSAN dealer. CAUTION ● High pressure halogen gas is sealed inside the halogen bulb. The bulb may break if the glass envelope is scratched or the bulb is dropped. ● When handling the bulb, do not touch the glass envelope. ● DO NOT TOUCH THE BULB ● Use the same number and wattage as originally installed: Low beam: Wattage: 51 Bulb no.: 9006* High beam: Wattage: 60 Bulb no.: 9005* *: Always check with the Parts Department at a NISSAN dealer for the latest parts information. ● Do not leave the bulb out of the headlight reflector for a long period of time as dust, moisture and smoke may enter the headlight body and affect the performance of the headlight. ● Do not leave the bulb out of the fog light for a long period of time as dust, moisture and smoke may enter the fog light body and affect the performance of the fog light. ● Aiming is not necessary after replacing the bulb. When aiming adjustment is necessary, contact a NISSAN dealer. FOG LIGHTS (if so equipped) Replacing the fog light bulb CAUTION ● High pressure halogen gas is sealed inside the halogen bulb. The bulb may break if the glass envelope is scratched or the bulb is dropped. ● When handling the bulb, do not touch the glass envelope. ● Use the same number and wattage as originally installed: Wattage 55 Bulb No. H11* *: Always check with the Parts Department at a NISSAN dealer for the latest parts information. 8-26 Maintenance and do-it-yourself Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X 4. Rotate the bulb counterclockwise and remove. 5. Remove by pulling it straight out of the fog light assembly. Do not shake or rotate the bulb when removing it. Do not touch the glass envelope. 6. Install in the reverse order of removal. EXTERIOR AND INTERIOR LIGHTS Item Wattage (W) Bulb No. 1. Disconnect the negative (-) battery cable. 2. Remove the three splash shield screws and move the splash shield out of the way. 3. Disconnect the bulb connector. Step light Wattage (W) Bulb No. 3.8 194 Cargo light 7 N1J High-mounted stop light* 13 912 7/27 3157K Rear combination light Tail/Stop Backup (reversing) 18 921K Turn 27 3156K 5 H5H License plate light* Headlight assembly LDI0362 Item High 60 HB3/9005 *: See a NISSAN dealer for replacement. Low* 51 HB4/9006 Park/Turn* 8/29 3457 Always check with the Parts Department at a NISSAN dealer for the latest parts information. Cornering* 27 3156 Front fog light 55 H11 Puddle lamp* 8 — Room/map lights 8 PLW 578 Personal lights Base model 8 TS578 Airplane type 8 2GL T2P 3.4 158 Glove box light 3.4 158 Vanity mirror light* 1.32 — Footwell Maintenance and do-it-yourself 8-27 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. Room/map light Front personal lights Step light Puddle lamp High-mount stoplight Cargo light License plate light Rear combination light Headlight assembly Fog light WDI0263 Replacement procedures LDI0360 All other lights are either type A, B, C or D. When replacing a bulb, first remove the lens, lamp and/or cover. Indicates bulb removal Indicates bulb installation 8-28 Maintenance and do-it-yourself Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X LDI0363 Room/map lights 1 to protect the housing. Use a cloth s LDI0364 Personal lights – Type A 1 to protect the housing. Use a cloth s LDI0365 Personal lights – Type B 1 to protect the housing. Use a cloth s Maintenance and do-it-yourself 8-29 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X LDI0341 Step light 1 to protect the housing. Use a cloth s LDI0366 Cargo light 1 to protect the housing. Use a cloth s LDI0367 Rear combination light 8-30 Maintenance and do-it-yourself Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X WHEELS AND TIRES ● Most tires naturally lose air over time. ● Tires can lose air suddenly when driven over potholes or other objects or if the vehicle strikes a curb while parking. ● Before taking a long trip, or whenever you heavily load your vehicle, use a tire pressure gauge to ensure that the tire pressures are at the specified level. The tire pressures should be checked when the tires are cold. The tires are considered COLD after the vehicle has been parked for 3 or more hours, or driven less than 1 mile (1.6 km) at moderate speeds. ● Do not drive your vehicle over 85 MPH (137 km/h) unless it is equipped with high speed rated tires. Driving faster than 85 MPH (137 km/h) may result in tire failure, loss of control and possible injury. Incorrect tire pressure, including under inflation, may adversely affect tire life and vehicle handling. ● For additional information regarding tires, refer to “Important Tire Safety Information” (US) or “Tire Safety Information” (Canada) in the Warranty Information Booklet. WDI0210 If you have a flat tire, see the “In case of emergency” section of this manual. TIRE PRESSURE Tire inflation pressure Check the tire pressures (including the spare) often and always prior to long distance trips. The recommended tire pressure specifications are shown on the Tire and Loading Information label under the 9Recommended Cold Tire Inflation Pressure9 heading. The Tire and Loading Information label is affixed to the driver side center pillar. Tire pressures should be checked regularly because: WARNING ● Improperly inflated tires can fail suddenly and cause an accident. ● The vehicle weight capacity is indicated on the Tire and Loading Information label. Do not load your vehicle beyond this capacity. Overloading your vehicle may result in reduced tire life, unsafe operating conditions due to premature tire failure, or unfavorable handling characteristics and could also lead to a serious accident. Loading beyond the specified capacity may also result in failure of other vehicle components. Low tire pressure warning system The low tire pressure warning system displays the tire pressure of all tires (except the spare tire) on the display screen by sending a signal from a sensor that is installed in each wheel. For more details, refer to “Low tire pressure warning light” in the “Instruments and controls” section, “Low tire pressure warning system” in the “Starting and driving” section, and “Flat tire” in the “In case of emergency” section. The low tire pressure warning system will activate only when the vehicle is driven at speeds above 20 MPH (32 km/h). Maintenance and do-it-yourself 8-31 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X LDI0392 Tire and loading information label (for US) 1 s Seating capacity: The maximum number of occupants that should be seated in the vehicle. 2 s Vehicle load limit: See loading information in the Technical and consumer information section. 3 s Original tire size: The size of the tires originally installed on the vehicle at the factory. s 4 Recommended cold tire inflation pressure: Inflate the tires to this pressure when the tires are cold. Tires are considered COLD after the vehicle has been parked for 3 or more hours, or driven less than 1 mile (1.6 km) at moderate speeds. The recommended cold tire inflation is set by the manufacturer to provide the best tire wear and vehicle handling characteristics based on the vehicles GVWR. 5 s Tire size – refer to “Tire labeling” later in this section. s 7 . Spare tire size or compact spare tire and s size (if so equipped) 6 LDI0393 Checking tire pressure 1. Remove the valve stem cap from the tire. 2. Press the pressure gauge squarely onto the valve stem. Do not press too hard or force the valve stem sideways, or air will escape. If the hissing of air escaping from the tire is heard while checking the pressure, reposition the gauge to eliminate this leakage. 3. Remove the gauge. 4. Read the tire pressure on the gauge stem and compare to the specification shown on the Tire and Loading Information label. 8-32 Maintenance and do-it-yourself Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X 5. Add air to the tire as needed. If too much air is added, press the core of the valve stem briefly with the tip of the gauge stem to release pressure. Recheck the pressure and add or release air as needed. 6. Install the valve stem cap. 7. Check the pressure of all other tires, including the spare. Size Cold Tire Inflation Pressure Front Original Tire P225/65/R16 P225/60/R17 240 kPa, 35 PSI Rear Original Tire P225/65/R16 P225/60/R17 240 kPa, 35 PSI Spare Tire T135/80D16 420 kPa, 60 PSI WDI0394 TIRE LABELING Federal law requires tire manufacturers to place standardized information on the sidewall of all tires. This information identifies and describes the fundamental characteristics of the tire and also provides the tire identification number (TIN) for safety standard certification. The TIN can be used to identify the tire in case of a recall. Maintenance and do-it-yourself 8-33 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X WDI0395 (1) Tire size (example: P215/65R15 95H) 1. P: The 9P9 indicates the tire is designed for passenger vehicles. 2. Three-digit number: This number gives the width in millimeters of the tire from sidewall edge to sidewall edge. 6. Two- or three-digit number: This number is the tire’s load index. It is a measurement of how much weight each tire can support. You may not find this information on all tires because it is not required by law. 7. Tire speed rating. You should not drive the vehicle faster than the tire speed rating. 3. Two-digit number: This number, known as the aspect ratio, gives the tire’s ratio of height to width. 4. R: The 9R9 stands for radial. 5. Two-digit number: This number is the wheel or rim diameter in inches. 8-34 Maintenance and do-it-yourself Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X This number indicates the maximum load in kilograms and pounds that can be carried by the tire. When replacing the tires on the vehicle, always use a tire that has the same load rating as the factory installed tire. (6) Term of ”tubeless” or ”tube type” Indicates whether the tire requires an inner tube (“tube type”) or not (“tubeless”). (7) The word ”radial” The word 9radial9 is shown if the tire has radial structure. WDI0396 (2) TIN (Tire Identification Number) for a new tire (example: DOT XX XX XXX XXXX) 1. DOT: Abbreviation for the 9Department Of Transportation.9 The symbol can be placed above, below or to the left or right of Tire Identification Number. 6. Four numbers represent the week and year the tire was built. For example, the numbers 3103 means the 31st week of 2003. (3) Tire ply composition and material 2. Two-digit code: Manufacturer’s identification mark The number of layers or plies of rubber-coated fabric in the tire. Tire manufacturers also must indicate the materials in the tire, which include steel, nylon, polyester, and others. 3. Two-digit code: Tire size (4) Maximum permissible inflation pressure 4. Three-digit code: Tire type code (Optional) This number is the greatest amount of air pressure that should be put in the tire. Do not exceed the maximum permissible inflation pressure. 5. Three-digit code: Date of Manufacture (8) Manufacturer or brand name Manufacturer or brand name is shown. Other Tire-related Terminology In addition to the many terms that are defined throughout this section, Intended Outboard Sidewall is (1) the sidewall that contains a whitewall, bears white lettering or bears manufacturer, brand, and/or model name molding that is higher or deeper than the same molding on the other sidewall of the tire, or (2) the outward facing sidewall of an asymmetrical tire that has a particular side that must always face outward when mounted on a vehicle. (5) Maximum load rating Maintenance and do-it-yourself 8-35 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X TYPES OF TIRES WARNING ● When changing or replacing tires, be sure all four tires are of the same type (i.e., Summer, All Season or Snow) and construction. A NISSAN dealer may be able to help you with information about tire type, size, speed rating and availability. Replacement tires may have a lower speed rating than the factory equipped tires, and may not match the potential maximum vehicle speed. Never exceed the maximum speed rating of the tire. ● For additional information regarding tires, refer to “Important Tire Safety Information” (US) or “Tire Safety Information” (Canada) in the Warranty Information Booklet. All season tires NISSAN specifies All Season tires on some models to provide good performance all year, including snowy and icy road conditions. All Season tires are identified by ALL SEASON and/or M&S on the tire sidewall. Snow tires have better snow traction than All Season tires and may be more appropriate in some areas. Summer tires NISSAN specifies summer tires on some models to provide superior performance on dry roads. Summer tire performance is substantially reduced in snow and ice. Summer tires do not have the tire traction rating “M&S” on the tire sidewall. If you plan to operate your vehicle in snowy or icy conditions, NISSAN recommends the use of SNOW tires or ALL SEASON tires on all four wheels. Snow tires If snow tires are needed, it is necessary to select tires equivalent in size and load rating to the original equipment tires. If you do not, it can adversely affect the safety and handling of your vehicle. Generally, snow tires have lower speed ratings than factory equipped tires and may not match the potential maximum vehicle speed. Never exceed the maximum speed rating of the tire. If you install snow tires, they must be the same size, brand, construction and tread pattern on all four wheels. For additional traction on icy roads, studded tires may be used. However, some U.S. states and Canadian provinces prohibit their use. Check local, state and provincial laws before installing studded tires. Skid and traction capabilities of studded snow tires on wet or dry surfaces may be poorer than that of non-studded snow tires. TIRE CHAINS Use of tire chains may be prohibited according to location. Check the local laws before installing tire chains. When installing tire chains, make sure they are the proper size for the tires on your vehicle and are installed according to the chain manufacturer’s suggestions. Use only SAE class “S” chains. Class “S” chains are used on vehicles with restricted tire to vehicle clearance. Vehicles that can use Class “S” chains are designed to meet the minimum clearances between the tire and the closest vehicle suspension or body component required to accommodate the use of a winter traction device (tire chains or cables). The minimum clearances are determined using the factory equipped tires. Other types may damage your vehicle. Use chain tensioners when recommended by the tire chain manufacturer to ensure a tight fit. Loose end links of the tire chain must be secured or removed to prevent the possibility of whipping action damage to the fenders or underbody. If possible, avoid fully loading your vehicle when using tire chains. In addition, drive at a reduced speed. Otherwise, your vehicle may be damaged and/or vehicle handling and performance may be adversely affected. 8-36 Maintenance and do-it-yourself Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X Tire chains must be installed only on the front wheels and not on the rear wheels. The wheel nuts must be kept tightened to specifications at all times. It is recommended that wheel nuts be tightened to specification at each tire rotation interval. Never install tire chains on a TEMPORARY USE ONLY spare tire. WARNING Do not use tire chains on dry roads. Driving with chains in such conditions can cause damage to the various mechanisms of the vehicle due to some overstress. ● After rotating the tires, check and adjust the tire pressure. ● Retighten the wheel nuts when the vehicle has been driven for 600 miles (1,000 km) (also in cases of a flat tire, etc.). WDI0258 CHANGING WHEELS AND TIRES Tire rotation NISSAN recommends rotating the tires every 7,500 miles (12,000 km). ● Do not include the spare tire in the tire rotation. ● For additional information regarding tires, refer to “Important Tire Safety Information” (US) or “Tire Safety Information” (Canada) in the Warranty Information Booklet. See “Flat tire” in the “In case of emergency” section of this manual for tire replacing procedures. As soon as possible, tighten the wheel nuts to the specified torque with a torque wrench. Wheel nut tightening torque: 83 ft-lb (112 N·m) Maintenance and do-it-yourself 8-37 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X ● The original tires have built-in tread wear indicators. When the wear indicators are visible, the tire(s) should be replaced. ● Improper service of the spare tire may result in serious personal injury. If it is necessary to repair the spare tire, contact a NISSAN dealer. ● For additional information regarding tires, refer to “Important Tire Safety Information” (US) or “Tire Safety Information” (Canada) in the Warranty Information Booklet. WDI0259 1. 2. Wear indicator Location mark Tire wear and damage WARNING ● Tires should be periodically inspected for wear, cracking, bulging or objects caught in the tread. If excessive wear, cracks, bulging or deep cuts are found, the tire(s) should be replaced. Replacing wheels and tires When replacing a tire, use the same size, tread design, speed rating and load carrying capacity as originally equipped. Recommended types and sizes are shown in “Wheels and tires” in the “Technical and consumer information” section of this manual. WARNING ● The use of tires other than those recommended or the mixed use of tires of different brands, construction (bias, bias-belted or radial), or tread patterns can adversely affect the ride, braking, handling, ground clearance, body-totire clearance, tire chain clearance, speedometer calibration, headlight aim and bumper height. Some of these effects may lead to accidents and could result in serious personal injury. ● If the wheels are changed for any reason, always replace with wheels which have the same off-set dimension. Wheels of a different off-set could cause premature tire wear, degrade vehicle handling characteristics and/or interference with the brake discs/drums. Such interference can lead to decreased braking efficiency and/or early brake pad/shoe wear. Refer to “Wheels and tires” in the “Technical and consumer information” section of this manual for wheel off-set dimensions. 8-38 Maintenance and do-it-yourself Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X ● When a spare tire is mounted or a wheel is replaced, tire pressure will not be indicated and the low tire pressure warning system will not function. Contact your NISSAN dealer as soon as possible for tire replacement and/or system resetting. ● Do not install a deformed wheel or tire even if it has been repaired. Such wheels or tires could have structural damage and could fail without warning. ● The use of retread recommended. tires is not ● For additional information regarding tires, refer to “Important Tire Safety Information” (US) or “Tire Safety Information” (Canada) in the Warranty Information Booklet. Wheel balance ● For additional information regarding tires, refer to “Important Tire Safety Information” (US) or “Tire Safety Information” (Canada) in the Warranty Information Booklet . Care of wheels ● Wash the wheels when washing the vehicle to maintain their appearance. ● Clean the inner side of the wheels when the wheel is changed or the underside of the vehicle is washed. WARNING ● The spare tire should be used for emergency use only. It should be replaced with the standard tire at the first opportunity to avoid possible tire or differential damage. ● Drive carefully while the TEMPORARY USE ONLY spare tire is installed. Avoid sharp turns and abrupt braking while driving. ● Do not use abrasive cleaners when washing the wheels. ● Periodically check spare tire inflation pressure. Always keep the pressure of the TEMPORARY USE ONLY spare tire at 60 psi (420 kPa, 4.2 bar). ● Inspect wheel rims regularly for dents or corrosion. Such damage may cause loss of pressure or poor seal at the tire bead. ● With the TEMPORARY USE ONLY spare tire installed do not drive the vehicle at speeds faster than 50 MPH (80 km/h). ● NISSAN recommends waxing the road wheels to protect against road salt in areas where it is used during winter. ● When driving on roads covered with snow or ice, the TEMPORARY USE ONLY spare tire should be used on the rear wheels and the original tire used on the front wheels (drive wheels). Use tire chains only on the front (original) tires. Unbalanced wheels may affect vehicle handling and tire life. Even with regular use, wheels can get out of balance. Therefore, they should be balanced as required. Spare tire (TEMPORARY USE ONLY spare tire) Wheel balance service should be performed with the wheels off the vehicle. Spin balancing the wheels on the vehicle could lead to mechanical damage. Observe the following precautions if the TEMPORARY USE ONLY spare tire must be used. Otherwise, your vehicle could be damaged or involved in an accident: Maintenance and do-it-yourself 8-39 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X ● Tire tread of the TEMPORARY USE ONLY spare tire will wear at a faster rate than the standard tire. Replace the spare tire as soon as the tread wear indicators appear. ● Do not use the spare tire on other vehicles. ● Do not use more than one spare tire at the same time. ● Do not tow a trailer when the TEMPORARY USE ONLY spare tire is installed. CAUTION ● Do not use tire chains on a TEMPORARY USE ONLY spare tire. Tire chains will not fit properly and may cause damage to the vehicle. ● Because the TEMPORARY USE ONLY spare tire is smaller than the original tire, ground clearance is reduced. To avoid damage to the vehicle, do not drive over obstacles. Also, do not drive the vehicle through an automatic car wash since it may get caught. 8-40 Maintenance and do-it-yourself Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X 9 Technical and consumer information Capacities and recommended fuel/lubricants . . . . . . . . . 9-2 Fuel recommendation . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-3 Engine oil and oil filter recommendation . . . . . . . . . . . 9-5 Recommended SAE viscosity number . . . . . . . . . . . . 9-6 Air conditioner system refrigerant and lubricant recommendations . . . . . . . . . . . . . . . . . . . . . . 9-6 Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-7 Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-7 Wheels and tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-8 Dimensions and weights . . . . . . . . . . . . . . . . . . . . . . . . 9-8 When traveling or registering your vehicle in another country . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-9 Vehicle identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-9 Vehicle identification number (VIN) plate . . . . . . . . . . 9-9 Vehicle identification number (chassis number) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-9 Engine serial number. . . . . . . . . . . . . . . . . . . . . . . . . . . 9-10 F.M.V.S.S. certification label . . . . . . . . . . . . . . . . . . . . 9-10 Emission control information label . . . . . . . . . . . . . . . 9-10 Tire and loading information label. . . . . . . . . . . . . . . . 9-11 Air conditioner specification label. . . . . . . . . . . . . . . . 9-11 Installing front license plate . . . . . . . . . . . . . . . . . . . . . . . . 9-11 Vehicle loading information . . . . . . . . . . . . . . . . . . . . . . . . 9-12 Terms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-12 Vehicle load capacity . . . . . . . . . . . . . . . . . . . . . . . . . . 9-12 Loading tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-13 Towing a trailer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-14 Maximum load limits . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-14 Towing load/specification chart . . . . . . . . . . . . . . . . . 9-15 Towing safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-15 Flat towing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-17 Uniform tire quality grading . . . . . . . . . . . . . . . . . . . . . . . . 9-18 Emission control system warranty . . . . . . . . . . . . . . . . . . 9-19 Reporting safety defects (US only) . . . . . . . . . . . . . . . . . 9-19 Readiness for inspection/maintenance (I/M) test . . . . . 9-20 Owner’s Manual/Service Manual order information . . . 9-21 In the event of a collision . . . . . . . . . . . . . . . . . . . . . . . 9-22 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X CAPACITIES AND RECOMMENDED FUEL/LUBRICANTS The following are approximate capacities. The actual refill capacities may be a little different. When refilling, follow the procedure described in the “Maintenance and do-it-yourself” section to determine the proper refill capacity. Capacity (Approximate) Fuel Recommended Fluids and Lubricants US measure Imp measure Liter 20.1 gal 16-3/4 gal 76 Unleaded gasoline with an octane rating of at least 87 AKI (RON 91)*1 Engine oil *8 Drain and Refill With oil filter change 4-1/4 qt 3-1/2 qt 4.0 Without oil filter change 3-7/8 qt 3-1/4 qt 3.7 • API Certification Mark *2 *3 • API grade SL, Energy Conserving *2 *3 • ILSAC grade GF-III*2 *3 With reservoir 11-1/8 qt 10-1/4 qt 10.5 50% Genuine NISSAN Long Life Anti-freeze Coolant or equivalent 50% Demineralized or distilled water Cooling system Automatic transmission fluid 4 Speed 5 Speed Refill to the proper level according to the instructions in the “Maintenance and do-it-yourself” section. Power steering fluid (PSF) Genuine Nissan Matic D ATF (Continental U.S. and Alaska) or Canada NISSAN Automatic Transmission Fluid.*4 Genuine Nissan Matic K ATF *5 Genuine NISSAN PSF or equivalent.*9 Brake fluid Genuine NISSAN Super Heavy Duty Brake Fluid*6 or equivalent DOT 3 (US FMVSS No. 116) Multi-purpose grease — — — NLGI No. 2 (Lithium Soap base) Air conditioning system refrigerant — — — HFC-134a (R-134a)*7 Air conditioning system lubricants — — — NISSAN A/C System Lubricant Type DH-PS or equivalent*7 Windshield washer fluid (shared between front and rear wipers) 1-1/4 gal 1 gal 4.5 Genuine NISSAN Windshield Washer Concentrate Cleaner & Anti-freeze or equivalent *1: For further details, see “Fuel recommendation.” *2: For further details, see “Engine oil and oil filter recommendations.” *3: For further details, see “Recommended SAE engine oil viscosity.” *4: Dexron™ III/Mercon™ or equivalent may also be used. Outside the Continental United States and Alaska contact a NISSAN dealership for more information regarding suitable fluids, including recommended brand(s) of Dexron™ III/Mercon™ Automatic Transmission Fluid. *5: Using automatic transmission fluid other than Genuine Nissan Matic K ATF will cause deterioration in driveability and automatic transmission durability, and may damage the automatic transmission, which is not covered by the NISSAN new vehicle warranty. *6: Available in mainland USA through your NISSAN dealer. *7: For further details, see “Air conditioner specification label.” *8: For further details, see “Changing engine oil.” *9: For Canada, NISSAN Automatic Transmission Fluid (ATF), Dexron™ III/Mercon™, or equivalent ATF may also be used. 9-2 Technical and consumer information Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X FUEL RECOMMENDATION Gasoline containing oxygenates Use unleaded regular gasoline with an octane rating of at least 87 AKI (Anti-Knock Index) number (Research octane number 91). Some fuel suppliers sell gasoline containing oxygenates such as ethanol, MTBE and methanol with or without advertising their presence. NISSAN does not recommend the use of fuels of which the oxygenate content and the fuel compatibility for your NISSAN cannot be readily determined. If in doubt, ask your service station manager. For improved vehicle performance, NISSAN recommends the use of unleaded premium gasoline with an octane rating of at least 91 AKI number (Research octane number 96). CAUTION ● Using a fuel other than that specified could adversely affect the emission control system, and may also affect the warranty coverage. ● Under no circumstances should a leaded gasoline be used, because this will damage the three-way catalyst. Reformulated gasoline Some fuel suppliers are now producing reformulated gasolines. These gasolines are specially designed to reduce vehicle emissions. NISSAN supports efforts towards cleaner air and suggests that you use reformulated gasoline when available. If you use oxygenate-blend gasoline, please take the following precautions as the usage of such fuels may cause vehicle performance problems and/or fuel system damage. ● The fuel should be unleaded and have an octane rating no lower than that recommended for unleaded gasoline. ● If an oxygenate-blend other than methanol blend is used, it should contain no more than 10% oxygenate. (MTBE may, however, be added up to 15%.) ● If a methanol blend is used, it should contain no more than 5% methanol (methyl alcohol, wood alcohol). It should also contain a suitable amount of appropriate cosolvents and corrosion inhibitors. If not properly formulated with appropriate cosolvents and corrosion inhibitors, such methanol blends may cause fuel system damage and/or vehicle performance problems. At this time, sufficient data is not available to ensure that all methanol blends are suitable for use in NISSAN vehicles. If any driveability problems such as engine stalling and difficult hot-starting are experienced after using oxygenate-blend fuels, immediately change to a non-oxygenate fuel or a fuel with a low blend of MTBE. Take care not to spill gasoline during refueling. Gasoline containing oxygenates can cause paint damage. Aftermarket fuel additives NISSAN does not recommend the use of any aftermarket fuel additives (for example, fuel injector cleaner, octane booster, intake valve deposit removers, etc.) which are sold commercially. Many of these additives intended for gum, varnish or deposit removal may contain active solvents or similar ingredients that can be harmful to the fuel system and engine. Octane rating tips In most parts of North America, you should use unleaded gasoline with an octane rating of at Technical and consumer information 9-3 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X least 87 AKI (Anti-Knock Index) number. However, you may use unleaded gasoline with an octane rating as low as 85 AKI (Anti-Knock Index) number in high altitude areas [over 4,000 ft (1,219 m)] such as: Colorado, Montana, New Mexico, Utah, Wyoming, northeastern Nevada, southern Idaho, western South Dakota, western Nebraska, and the part of Texas which is directly south of New Mexico. However, now and then you may notice light spark knock for a short time while accelerating or driving up hills. This is not a cause for concern, because you get the greatest fuel benefit when there is light spark knock for a short time under heavy engine load. Using unleaded gasoline with an octane rating lower than stated above can cause persistent, heavy “spark knock.” (“Spark knock” is a metallic rapping noise.) If severe, this can lead to engine damage. If you detect a persistent heavy spark knock even when using gasoline of the stated octane rating, or if you hear steady spark knock while holding a steady speed on level roads, have a NISSAN dealer correct the condition. Failure to correct the condition is misuse of the vehicle, for which NISSAN is not responsible. Incorrect ignition timing may result in spark knock, after-run and/or overheating, which may cause excessive fuel consumption or engine damage. If any of the above symptoms are encountered, have your vehicle checked at a NISSAN dealer. 9-4 Technical and consumer information Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X Oil additives NISSAN does not recommend the use of oil additives. The use of an oil additive is not necessary when the proper oil type is used and maintenance intervals are followed. Oil which may contain foreign matter or has been previously used should not be used. Oil viscosity WTI0082 ENGINE OIL AND OIL FILTER RECOMMENDATION Selecting the correct oil It is essential to choose engine oil with the correct quality and viscosity to ensure satisfactory engine life and performance. NISSAN recommends the use of a low friction oil (energy conserving oil) in order to improve fuel economy and conserve energy. Oils which do not have the specified quality label should not be used as they could cause engine damage. Only those engine oils with the American Petroleum Institute (API) CERTIFICATION MARK on the front of the container should be used. This type of oil supersedes the existing API SG, SH, or SJ and Energy Conserving II categories. If you cannot find engine oil with the API CERTIFICATION MARK, use API grade SL Energy Conserving oil. An oil with a single designation SL, or in combination with other categories (for example, SL/CF) may also be used if one with the API CERTIFICATION MARK cannot be found. An ILSAC grade GF-III oil can also be used. NISSAN recommends mineral based oils. These oils must, however, meet the API quality and SAE viscosity ratings specified for your vehicle. The engine oil viscosity or thickness changes with temperature. Because of this, it is important to select the engine oil viscosity based on the temperatures at which the vehicle will be operated before the next oil change. The chart “Recommended SAE viscosity number” shows the recommended oil viscosities for the expected ambient temperatures. Choosing an oil viscosity other than that recommended could cause serious engine damage. Selecting the correct oil filter Your new NISSAN vehicle is equipped with a high-quality genuine NISSAN oil filter. When replacing, use a genuine NISSAN oil filter or its equivalent for the reason described in “Change intervals”. Technical and consumer information 9-5 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X Change intervals AIR CONDITIONER SYSTEM REFRIGERANT AND LUBRICANT RECOMMENDATIONS The oil and oil filter change intervals for your engine are based on the use of the specified quality oils and filters. Using engine oil and filters that are not of the specified quality, or exceeding recommended oil and filter change intervals could reduce engine life. Damage to the engine caused by improper maintenance or use of incorrect oil and filter quality and/or viscosity is not covered by the NISSAN new vehicle warranty. The air conditioner system in your NISSAN vehicle must be charged with the refrigerant HFC-134a (R-134a) and the lubricant, NISSAN A/C system oil DH-PS or the exact equivalents. CAUTION Your engine was filled with a high-quality engine oil when it was built. You do not have to change the oil before the first recommended change interval. Oil and filter change intervals depend upon how you use your vehicle. The use of any other refrigerant or lubricant will cause severe damage to the air conditioning system and will require the replacement of all air conditioner system components. Operation under the following conditions may require more frequent oil and filter changes: ● repeated short distance driving at cold outside temperatures ● driving in dusty conditions ● extensive idling ● towing a trailer ATI1028 RECOMMENDED SAE VISCOSITY NUMBER ● SAE 5W-30 viscosity oil is preferred for all temperatures. SAE 10W-30 or SAE 10W-40 viscosity oils may be used if the ambient temperature is above 0°F (-18°C). The refrigerant HFC-134a (R-134a) in your NISSAN vehicle does not harm the earth’s ozone layer. Although this refrigerant does not affect the earth’s atmosphere, certain government regulations require the recovery and recycling of any refrigerant during automotive air conditioner system service. A NISSAN dealer has the trained technicians and equipment needed to recover and recycle your air conditioner system refrigerant. Contact a NISSAN dealer when servicing your air conditioner system. 9-6 Technical and consumer information Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X SPECIFICATIONS ENGINE Model VQ35DE Type Gasoline, 4-cycle, DOHC Cylinder arrangement Bore x Stroke Displacement Firing order 6-cylinder, V-block, Slanted at 60° in (mm) 3.760 x 3.205 (95.5 x 81.4) cu in (cm3) 213.45 (3,498) 1–2–3–4–5–6 Idle speed A/T (in “N” position) Ignition timing (degree B.T.D.C. at idle speed) See the “Emission Control label” on the underside of the hood. CO % at idle Standard PLFR5A-11 Spark plug Hot PLFR4A-11 Cold PLFR6A-11 Spark plug gap (Nominal) Camshaft operation in (mm) 0.043 (1.1) Timing chain The spark ignition system of this vehicle meets all requirements of the Canadian Interference-Causing Equipment Regulations. Technical and consumer information 9-7 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X WHEELS AND TIRES DIMENSIONS AND WEIGHTS Wheels Overall length in (mm) 204.13(5,185) 16 x 6.5JJ Overall width in (mm) 77.64(1,972) 17 x 6.5JJ Overall height with roof rack in (mm) 71.90(1,826) without roof rack in (mm) 70.0 (1,778) Tires P225/65R16 P225/60R17 Front tread in (mm) 67.32(1,710) T135/80*16 Rear tread in (mm) 67.32(1,710) 16” H Wheelbase in (mm) 124.02(3,150) 17” H Gross vehicle weight rating Spare tire Speed rating *: “R” or “D” depending on tire manufacturer Gross axle weight rating Front Rear lb (kg) See the “F.M.V.S.S. certification label” on the center pillar between the lb (kg) driver’s side front and side doors. lb (kg) 9-8 Technical and consumer information Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X WHEN TRAVELING OR REGISTERING YOUR VEHICLE IN ANOTHER COUNTRY VEHICLE IDENTIFICATION When planning to drive your NISSAN vehicle in another country, you should first find out if the fuel available is suitable for your vehicle’s engine. Using fuel with an octane rating that is too low may cause engine damage. All gasoline vehicles must be operated with unleaded gasoline. Therefore, avoid taking your vehicle to areas where appropriate fuel is not available. When transferring the registration of your vehicle to another country, state, province or district, it may be necessary to modify the vehicle to meet local laws and regulations. The laws and regulations for motor vehicle emission control and safety standards vary according to the country, state, province or district; therefore, vehicle specifications may differ. When any vehicle is to be taken into another country, state, province or district and registered, its modifications, transportation, and registration are the responsibility of the user. NISSAN is not responsible for any inconvenience that may result. LTI0077 LTI0083 VEHICLE IDENTIFICATION NUMBER (VIN) PLATE VEHICLE IDENTIFICATION NUMBER (chassis number) The vehicle identification number (VIN) plate is attached as shown. This number is the identification for your vehicle and is used in the vehicle registration. The vehicle identification number is located as shown. Technical and consumer information 9-9 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X WTI0049 LTI0078 ENGINE SERIAL NUMBER F.M.V.S.S. CERTIFICATION LABEL The number is stamped on the engine as shown. The Federal Motor Vehicle Safety Standard (F.M.V.S.S.) certification label is affixed as shown. This label contains valuable vehicle information, such as: Gross Vehicle Weight Ratings (GVWR), Gross Axle Weight Rating (GAWR), month and year of manufacture, Vehicle Identification Number (VIN), etc. Review it carefully. LTI0079 EMISSION CONTROL INFORMATION LABEL The emission control information label is attached as shown. 9-10 Technical and consumer information Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X INSTALLING FRONT LICENSE PLATE LTI0084 WTI0080 TIRE AND LOADING INFORMATION LABEL AIR CONDITIONER SPECIFICATION LABEL The cold tire pressure is shown on the Tire and Loading Information label. The label is located as shown. The air conditioner specification label is affixed as shown. LTI0081 Technical and consumer information 9-11 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X VEHICLE LOADING INFORMATION Use the following steps to mount the front license plate: Before mounting the license plate, confirm that the following parts are enclosed in the plastic bag: ● License plate bracket ● License plate bracket screws x 2 ● License plate screws x 2 ● Screw grommets x 2 1. Make a shallow hole in the bumper fascia at the location marks (small dimples) using a 0.39 in (10 mm) drill. To avoid damaging the area behind the fascia, apply only light pressure to the drill. 2. Insert the grommets into the holes in the bumper fascia. 3. Insert a small flat-bladed screwdriver into the grommet hole to turn the threaded part of the grommet 90°. 4. Mount the license plate bracket using the two longer screws. 5. Use the two shorter hex head screws to mount the license plate to the license plate bracket. WARNING ● It is extremely dangerous to ride in a cargo area inside a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. ● Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. ● Be sure everyone in your vehicle is in a seat and using a seat belt properly. TERMS It is important to familiarize yourself with the following terms before loading your vehicle: ● GAWR (Gross Axle Weight Rating) - maximum weight (load) limit specified for the front or rear axle. VEHICLE LOAD CAPACITY Do not exceed the load limit of your vehicle shown as 9The combined weight of occupants and cargo9 on the Tire and Loading Information label. Do not exceed the number of occupants shown as 9Seating Capacity9 on Tire and Loading Information label. To get 9the combined weight of occupants and cargo9, add the weight of all occupants, then add the total luggage weight. Examples are shown below. ● Curb Weight (actual weight of your vehicle) - vehicle weight including: standard and optional equipment, fluids, emergency tools, and spare tire assembly. This weight does not include passengers and cargo. ● GVW (Gross Vehicle Weight) - curb weight plus the combined weight of passengers and cargo. ● GVWR (Gross Vehicle Weight Rating) maximum total weight (load) limit specified for the vehicle. 9-12 Technical and consumer information Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X 6. If your vehicle will be towing a trailer, load from your trailer will be transferred to your vehicle. Consult this manual to determine how this reduces the available cargo and luggage load capacity of your vehicle. Before driving a loaded vehicle, confirm the you do not exceed the Gross Vehicle Weight Rating (GVWR) or the Gross Axle Weight Rating (GAWR) for your vehicle. LOADING TIPS WTI0091 Steps for determining correct load limit 1. Locate the statement “The combined weight of occupants and cargo should never exceed XXX pounds” on your vehicle’s tire placard. 2. Determine the combined weight of the driver and passengers that will be riding in your vehicle. 3. Subtract the combined weight of the driver and passengers from XXX kilograms or XXX pounds. 4. The resulting figure equals the available amount of cargo and luggage load capacity. For example, if the XXX amount equals 1400 lbs. and there will be five 150 lb. passengers in your vehicle, the amount of available cargo and luggage load capacity is 650 lbs. (1400-750 (5 * 150) = 650 lbs.) 5. Determine the combined weight of luggage and cargo being loaded on the vehicle. That weight may not safely exceed the available cargo and luggage load capacity calculated in Step 4. ● The GVW must not exceed GVWR or GAWR as specified on the F.M.V.S.S. certification label. ● Do not load the front and rear axle to the GAWR. Doing so will exceed the GVWR. WARNING ● Properly secure all cargo with ropes or straps to help prevent it from sliding or shifting. Do not place cargo higher than the seatbacks. In a sudden stop or collision, unsecured cargo could cause personal injury. Technical and consumer information 9-13 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X TOWING A TRAILER ● Do not load your vehicle any heavier than the GVWR or the maximum front and rear GAWRs. If you do, parts of your vehicle can break, tire damage could occur, or it can change the way your vehicle handles. This could result in loss of control and cause personal injury. ● Overloading not only can shorten the life of your vehicle and the tire, but can also cause unsafe vehicle handling and longer braking distances. This may cause a premature tire failure which could result in a serious accident and personal injury. Failures caused by overloading are not covered by the vehicle’s warranty. Your new vehicle was designed to be used primarily to carry passengers and cargo. Remember that towing a trailer places additional loads on your vehicle’s engine, drive train, steering, braking and other systems. A Nissan Trailer Towing Guide (U.S. only) is available from a NISSAN dealer. This guide includes information on trailer towing ability and the special equipment required for proper towing. CAUTION Vehicle damage resulting from improper towing procedures are not covered by NISSAN warranties. A NISSAN Trailer Towing Guide (U.S. only) containing information on trailer towing ability and the special equipment required may be obtained from a NISSAN dealer. MAXIMUM LOAD LIMITS Maximum trailer loads Never allow the total trailer load to exceed the value specified in the Towing Load/Specification Chart found later in this section. The total trailer load equals trailer weight plus its cargo weight. Towing loads greater than specified or using improper towing equipment could adversely affect vehicle handling, braking and performance. The ability of your vehicle to tow a trailer is not only related to the maximum trailer loads, but also the places you plan to tow. Tow weights appropriate for level highway driving may have to be reduced on very steep grades or in low traction situations (for example, on slippery boat ramps). 9-14 Technical and consumer information Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X TOWING LOAD/SPECIFICATION CHART TOWING LOAD / SPECIFICATION CHART UNIT: lb (kg) MAXIMUM TOWING LOAD 3,500 (1,587) MAXIMUM TONGUE LOAD 350 (158) TOWING SAFETY CA0009 Tongue load Keep the tongue load between 9 - 11 percent of the total trailer load within the maximum tongue load limits shown in the following Towing Load/Specification Chart. If the tongue load becomes excessive, rearrange cargo to allow for proper tongue load. Trailer hitch TI1012M Maximum gross vehicle weight/maximum gross axle weight The gross vehicle weight of the towing vehicle must not exceed the gross vehicle weight rating (GVWR) shown on the F. M. V. S. S. certification label. The gross vehicle weight equals the combined weight of the unloaded vehicle, passengers, luggage, hitch, trailer tongue load and any other optional equipment. In addition, front or rear gross axle weight must not exceed the gross axle weight rating (GAWR) shown on the F. M. V. S. S. certification label. Choose a proper hitch for your vehicle and trailer. A genuine NISSAN trailer hitch is available from your NISSAN dealer. Make sure the trailer hitch is securely attached to the vehicle, to help avoid personal injury or property damage due to sway caused by crosswinds, rough road surfaces or passing trucks. CAUTION ● Do not use axle-mounted hitches. ● The hitch should not be attached to or affect the operation of the impactabsorbing bumper. Technical and consumer information 9-15 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X ● Do not modify the vehicle exhaust system, brake system, etc. to install a trailer hitch. not to the vehicle bumper or axle. Be sure to leave enough slack in the chains to permit turning corners. ● To reduce the possibility of additional damage if your vehicle is struck from the rear, where practical, remove the hitch and/or receiver when not in use. Trailer lights ● After the hitch is removed, seal the bolt holes to prevent exhaust fumes, water or dust from entering the passenger compartment. ● Regularly check that all trailer hitch mounting bolts are securely mounted. Tire pressures ● When towing a trailer, inflate the vehicle tires to the recommended cold tire pressure indicated on the tire placard. ● Trailer tire condition, size, load rating and proper inflation pressure should be in accordance with the trailer and tire manufacturer’s specifications. Safety chains Always use suitable safety chains between your vehicle and the trailer. The safety chains should be crossed and should be attached to the hitch, Trailer lights should comply with federal and/or local regulations. A genuine NISSAN trailer tow harness is available from your NISSAN dealer. Trailer brakes If your trailer is equipped with a braking system, make sure it conforms to federal and/or local regulations and that it is properly installed. WARNING Never connect a trailer brake system directly to the vehicle brake system. ● Be certain your rearview mirrors conform to all federal, state or local regulations. If not, install any mirrors required for towing before driving the vehicle. Trailer towing tips In order to gain skill and an understanding of the vehicle’s behavior, you should practice turning, stopping and backing up in an area which is free from traffic. Steering stability and braking performance will be somewhat different than under normal driving conditions. ● Always secure items in the trailer to prevent load shift while driving. ● Avoid abrupt starts, acceleration or stops. ● Avoid sharp turns or lane changes. ● Always drive your vehicle at a moderate speed. Pre-towing tips ● Be certain your vehicle maintains a level position when a loaded and/or unloaded trailer is hitched. Do not drive the vehicle if it has an abnormal nose-up or nose-down condition; check for improper tongue load, overload, worn suspension or other possible causes of either condition. ● Always secure items in the trailer to prevent load shift while driving. ● Always block the wheels on both vehicle and trailer when parking. Parking on a slope is not recommended; however, if you must do so, first block the wheels and apply the parking brake, and then move the transmission shift selector lever into the P (Park) position. If you move the shift selector lever to the P (Park) position before blocking the wheels and applying the parking brake, transmission damage could occur. 9-16 Technical and consumer information Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X ● When going down a hill, shift into a lower gear and use the engine braking effect. When going up a long grade, downshift the transmission to a lower gear and reduce speed to reduce chances of engine overloading and/or overheating. However, for long steep grades, do not stay in 1st gear when driving above 35 MPH (55 km/h) or 2nd gear when driving above 58 MPH (93 km/h). ● If the engine coolant rises to an extremely high temperature when the air conditioner system is on, turn off the air conditioner. Coolant heat can be additionally vented by opening the windows, switching the fan control to high and setting the temperature control to the HOT position. ● Trailer towing requires more fuel than normal circumstances. ● Avoid towing a trailer for your vehicle’s first 500 miles (805 km). ● For the first 500 miles (805 km) that you do tow, do not drive over 50 MPH (80 km/h). ● Have your vehicle serviced more often than at intervals specified in the recommended Maintenance Schedule in the “NISSAN Service and Maintenance Guide”. ● When making a turn, your trailer wheels will be closer to the inside of the turn than your vehicle wheels. To compensate for this, make a larger than normal turning radius during the turn. ● Crosswinds and rough roads will adversely affect vehicle/trailer handling, possibly causing vehicle sway. When being passed by larger vehicles, be prepared for possible changes in crosswinds that could affect vehicle handling. If swaying does occur, firmly grip the steering wheel, steer straight ahead, and immediately (but gradually) reduce vehicle speed. This combination will help stabilize the vehicle. Never increase speed. ● Be careful when passing other vehicles. Passing while towing a trailer requires considerably more distance than normal passing. Remember, the length of the trailer must also pass the other vehicle before you can safely change lanes. ● To maintain engine braking efficiency and electrical charging performance, do not use overdrive. ● Avoid holding the brake pedal down too long or too frequently. This could cause the brakes to overheat, resulting in reduced braking efficiency. When towing a trailer, final drive gear oil should be replaced and transmission oil/fluid should be changed more frequently. For additional information, see the “Maintenance and do-it-yourself” section earlier in this manual. FLAT TOWING Towing your vehicle with all four wheels on the ground is sometimes called flat towing. This method is sometimes used when towing a vehicle behind a recreational vehicle, such as a motor home. CAUTION ● Failure to follow these guidelines can result in severe transmission damage. ● Whenever flat towing your vehicle, always tow forward, never backward. ● DO NOT tow any automatic transmission vehicle with all four wheels on the ground (flat towing). Doing so WILL DAMAGE internal transmission parts due to lack of transmission lubrication. ● For emergency towing procedures refer to “Towing recommended by NISSAN” in the “In case of emergency” section of this manual. Technical and consumer information 9-17 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X UNIFORM TIRE QUALITY GRADING Automatic Transmission To tow a vehicle equipped with an automatic transmission, an appropriate vehicle dolly MUST be placed under the towed vehicle’s drive wheels. Always follow the dolly manufacturer’s recommendations when using their product. DOT (Department of Transportation) Quality Grades: All passenger car tires must conform to federal safety requirements in addition to these grades. Quality grades can be found where applicable on the tire sidewall between tread shoulder and maximum section width. For example: Treadwear 200 Traction AA Temperature A Treadwear Treadwear grade is a comparative rating based on tire wear rate when tested under controlled conditions on specified government test courses. For example, a tire graded 150 would wear one and a half (1-1/2) times as well on the government course as a tire graded 100. However, relative tire performance depends on actual driving conditions, and may vary significantly due to variations in driving habits, service practices and differences in road characteristics and climate. Traction AA, A, B and C WARNING The traction grade assigned to your vehicle tires is based on straight-ahead braking traction tests and does not include acceleration, cornering, hydroplaning or peak traction characteristics. Temperature A, B and C Temperature grades are A (the highest), B, and C. They represent a tire’s resistance to heat build-up, and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause tire material to degenerate, reducing tire life. Excessive temperatures can lead to sudden tire failure. Grade C corresponds to a performance level which all passenger car tires must meet under the Federal Motor Vehicle Safety Standard No. 109. Grades A and B represent higher levels of performance on laboratory test wheels than the minimum required by law. The traction grades, from highest to lowest, are AA, A, B, and C. Those grades represent the tire’s ability to stop on wet pavement as measured under controlled conditions on specified government test surfaces of asphalt and concrete. A tire marked C may have poor traction performance. 9-18 Technical and consumer information Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X WARNING The temperature grade for this tire is established for a tire that is properly inflated and not overloaded. Excessive speed, under-inflation, or excessive loading, either separately or in combination, can cause heat build-up and possible tire failure. EMISSION CONTROL SYSTEM WARRANTY REPORTING SAFETY DEFECTS (US only) Your NISSAN vehicle is covered by the following emission warranties: If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying NISSAN. For USA 1. Emission Defects Warranty 2. Emissions Performance Warranty Details of these warranties may be found with other vehicle warranties in your Warranty Information Booklet which comes with your NISSAN vehicle. If you did not receive a Warranty Information Booklet, or it is lost, you may obtain a replacement by writing to: ● Nissan North America, Inc. Consumer Affairs Department P.O. Box 191 Gardena, CA 90248-0191 For Canada Emission Control System Warranty Details of these warranties may be found with other vehicle warranties in your Warranty Information Booklet which comes with your NISSAN vehicle. If you did not receive a Warranty Information Booklet, or it is lost, you may obtain a replacement by writing to: If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign. However, NHTSA cannot become involved in individual problems between you, your dealer, or NISSAN. To contact NHTSA, you may call the Auto Safety Hotline toll-free at 1-888-327-4236. You may also write to: NHTSA, U.S. Department of Transportation, Washington, D.C. 20590. You can also obtain other information about motor vehicle safety from the Hotline. You may notify NISSAN by contacting our Consumer Affairs Department, toll-free, at 1-800NISSAN-1. In Hawaii call 1-808-836-0888. ● Nissan Canada Inc. 5290 Orbitor Drive Mississauga, Ontario, L4W 4Z5 Technical and consumer information 9-19 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X READINESS FOR INSPECTION/ MAINTENANCE (I/M) TEST Due to legal requirements in some states and Canadian Provinces, your vehicle may be required to be in what is called the “ready condition” for an Inspection/Maintenance (I/M) test of the emission control system. The vehicle is set to the “ready condition” when it is driven through certain driving patterns. Usually, the ready condition can be obtained by ordinary usage of the vehicle. If a powertrain system component is repaired or the battery is disconnected, the vehicle may be reset to a “not ready” condition. Before taking the I/M test, drive the vehicle through the following pattern to set the vehicle to the ready condition. If you cannot or do not want to perform the driving pattern, a NISSAN dealer can conduct it for you. WARNING Always drive the vehicle in a safe and prudent manner according to traffic conditions and obey all traffic laws. 1. Start the engine when the engine coolant temperature gauge needle points to C. Allow the engine to idle until the gauge needle points between the C and H (normal operating temperature). 2. Accelerate the vehicle to 55 MPH (88 km/h), then quickly release the accelerator pedal completely and keep it released for at least 6 seconds. 3. Quickly depress the accelerator pedal for a moment, then drive the vehicle at a speed of 53 - 60 MPH (86 - 96 km/h) for at least 5 minutes. 4. Stop the vehicle. 5. Accelerate the vehicle to 35 MPH (55 km/h) and maintain the speed for 20 seconds. 6. Repeat steps 4 through 5 at least three times. 7. Accelerate the vehicle to 55 MPH (88 km/h) and maintain the speed for at least 3 minutes. 8. Stop the vehicle. Place the transmission selector lever in the P (Park) or N (Neutral) position. 9. Turn the engine off. 10. Repeat steps 1 - 8 at least one more time. If steps 1 through 7 are interrupted, repeat the preceding step. Any safe driving mode is acceptable between steps. Do not stop the engine until step 7 is completed. 9-20 Technical and consumer information Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X OWNER’S MANUAL/SERVICE MANUAL ORDER INFORMATION A genuine NISSAN Service Manual is the best source of service and repair information for your vehicle. Filled with wiring diagrams, illustrations and step-by-step diagnostic and adjustment procedures, this manual is the same one used by the factory trained technicians working at NISSAN dealerships. Also available are genuine NISSAN Owner’s Manuals, and genuine NISSAN Service and Owner’s Manuals for older NISSAN models. For USA For current pricing and availability of genuine NISSAN Service Manuals for the 2000 model year and later contact: Tweddle Litho Company 1-800-639-8841 www.nissan-techinfo.com For current pricing and availability of genuine NISSAN Service Manuals for the 1999 model year and prior, see a NISSAN dealer, or contact: DDS Distribution Service, Ltd. 20770 Westwood Road Strongsville, OH 44136 1-800-247-5321 Technical and consumer information 9-21 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X For current pricing and availability of genuine NISSAN Owner’s Manuals for the 2004 model year and prior, see a NISSAN dealer, or contact: DDS Distribution Service, Ltd. 20770 Westwood Road Strongsville, OH 44136 1-800-247-5321 For Canada To purchase a copy of a genuine NISSAN Service Manual or Owner’s Manual please contact your nearest NISSAN dealer. For the phone number and location of a NISSAN dealer in your area call the NISSAN Information Center at 1-800387-0122 and a bilingual NISSAN representative will assist you. Also available are genuine NISSAN Service and Owner’s Manuals for older NISSAN models. IN THE EVENT OF A COLLISION Unfortunately, accidents do occur. In this unlikely event, there is some important information you should know. Many insurance companies routinely authorize the use of non-genuine collision parts in order to cut costs, among other reasons. Insist on the use of genuine NISSAN collision parts! If you want your vehicle to be restored using parts made to NISSAN’s original exacting specifications – if you want to help it to last and hold its resale value, the solution is simple. Tell your insurance agent and your repair shop to only use Genuine NISSAN Collision Parts. NISSAN does not warrant non-NISSAN parts, nor does NISSAN’s warranty apply to damage caused by a non-genuine part. Using Genuine NISSAN Parts can help protect your personal safety, preserve your warranty protection and maintain the resale value of your vehicle. And if your vehicle was leased, using Genuine NISSAN Parts may prevent or limit unnecessary excess wear and tear expenses at the end of your lease. Why should you take a chance? In over 40 states, the law says you must be advised if non-genuine parts are used to repair your vehicle. And some states have enacted laws that restrict insurance companies from authorizing the use of non-genuine collision parts during the new vehicle warranty. These laws help protect you, so you can take action to protect yourself. It’s your right! If you should need further information visit us at: www.nissanusa.com. NISSAN designs its hoods with crumple zones to minimize the risk that the hood will penetrate the windshield of your vehicle in an accident. Nongenuine (imitation) parts may not provide such built in safeguards. Also, non-genuine parts often show premature wear, rust and corrosion. 9-22 Technical and consumer information Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X 10 Index A Adjusting pedal position . . . . . . . . . . . .3-22 Air bag (See supplemental restraint system) . . . . . . . . . . . . . . . . . . . . .1-15 Air bag system Front (See supplemental front impact air bag system) . . . . . . . . . . . . . . .1-22 Side and curtain (See supplemental side air bag and curtain side-impact air bag system) . . . . . . . . . . . . . . . . . . .1-27 Air bag warning labels . . . . . . . . . . . . .1-29 Air bag warning light . . . . . . . . . . .1-30, 2-9 Air cleaner housing filter . . . . . . . . . . . .8-18 Air conditioner Air conditioner operation . . . . . . . . . .4-20 Air conditioner service . . . . . . . . . . .4-30 Air conditioner specification label . . . . .9-11 Air conditioner system refrigerant and lubrication recommendations . . . . . . . .9-6 Heater and air conditioner controls . . . . . . . . . . . . . . . .4-17, 4-27 Rear seat air conditioner . . . . . . . . . .4-29 Servicing air conditioner . . . . . . . . . .4-30 Air flow charts . . . . . . . . . . . . . . . . . .4-21 Anchor point locations . . . . . . . . . . . . .1-54 Antenna . . . . . . . . . . . . . . . . . . . . .4-43 Anti-lock brake system (ABS) . . . . . . . . .5-16 Anti-lock brake warning light . . . . . . . . . .2-6 Audible reminders. . . . . . . . . . . . . . . .2-12 Audio system . . . . . . . . . . . . . . . . . .4-30 AM-FM-SAT radio with compact disc (CD) changer . . . . . . . . . . . . . . . AM-FM-SAT radio with compact disc (CD) player . . . . . . . . . . . . . . . . Compact Disc (CD) changer . . . . . . Compact disc (CD) player . . . . . . . . Radio . . . . . . . . . . . . . . . . . . . Rear audio controls . . . . . . . . . . . . Steering wheel audio control switch. . . Autolight switch . . . . . . . . . . . . . . . . Automatic Automatic drive positioner . . . . . . . . Automatic power window switch . . . . Automatic transmission fluid (ATF) . . . Automatic transmission position indicator light . . . . . . . . . . . . . . . Driving with automatic transmission. . . Transmission selector lever lock release Automatic anti-glare inside mirror . . . . . . .4-34 .4-34 .4-39 .4-37 .4-30 .4-43 .4-41 .2-16 .3-25 .2-37 .8-11 . .2-9 . .5-7 . .5-9 .3-23 B Back door . . . . . . . . . . . . . . . . . . . .3-15 Back door release . . . . . . . . . . . . . . .3-18 Battery . . . . . . . . . . . . . . . . . . . . . .8-15 Charge warning light . . . . . . . . . . . . .2-7 Battery replacement (See remote keyless entry system) . . .3-13, 8-25 Before starting the engine . . . . . . . . . . . .5-6 Belts (See drive belts) . . . . . . . . . . . . .8-16 Bench seat adjustment (3rd row) . . . . .1-8, 1-9 Brake Anti-lock brake system (ABS) . . . . . . .5-16 Brake booster . . . . . . . . . . . . . . . .8-23 Brake fluid . . . . . . . . . . . . . . . . . .8-13 Brake light (See stop light). . . . . . . . .8-27 Brake pedal . . . . . . . . . . . . . . . . .8-22 Brake system . . . . . . . . . . . . . . . .5-16 Brake warning light . . . . . . . . . . . . . .2-7 Brake wear indicators . . . . . . . .2-12, 8-22 Parking brake check . . . . . . . . . . . .8-22 Parking brake operation . . . . . . . . . .5-11 Self-adjusting brakes . . . . . . . . . . . .8-22 Break-in schedule. . . . . . . . . . . . . . . .5-13 Brightness control Instrument panel . . . . . . . . . . . . . .2-18 Bulb check/instrument panel . . . . . . . . . .2-6 Bulb replacement . . . . . . . . . . . . . . . .8-27 C Capacities and recommended fuel/lubricants. . . . . . . . . . . . . . . Captain’s chair adjustment (2nd row). . Car phone or CB radio . . . . . . . . . . Cargo (See vehicle loading information) CD care and cleaning . . . . . . . . . . CD changer (See audio system). . . . . CD player (See audio system) . . . . . . Check engine indicator light (See malfunction indicator light) . . . . . Child restraint with top tether strap . . . . . . . . . . Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X . . . . . . . . .9-2 . .1-6 .4-53 .9-12 .4-41 .4-39 .4-37 . . .2-10 . . .1-53 Child restraints . . . . . . .1-33, 1-34, 1-40, 1-51 Precautions on child restraints . . . . . . .1-40 Top tether strap anchor point locations . .1-54 Child safety rear door lock . . . . . . . . . . . .3-9 Child safety sliding door lock . . . . . . . . . .3-9 Chimes, audible reminders . . . . . . . . . . .2-12 Cleaning exterior and interior . . . . . . . . . .7-2 Clock (models with navigation system) . . . . . .4-14 (models without navigation system) . . . . .4-4 Cold weather driving . . . . . . . . . . . . . .5-21 Compact disc (CD) player . . . . . . . . . . .4-37 Control panel buttons With navigation system . . . . . . . . . . .4-8 Without navigation system. . . . . . . . . .4-2 Controls Audio controls (steering wheel) . . . . . .4-41 Heater and air conditioner controls . . . . . . . . . . . . . . . .4-17, 4-27 Rear audio controls . . . . . . . . . . . . .4-43 Rear seat air conditioner . . . . . . . . . .4-29 Convenience hook . . . . . . . . . . . . . . .2-29 Coolant Capacities and recommended fuel/lubricants. . . . . . . . . . . . . . . . .9-2 Changing engine coolant . . . . . . . . . .8-8 Checking engine coolant level. . . . . . . .8-7 Engine coolant temperature gauge . . . . .2-4 Cornering light . . . . . . . . . . . . . . . . .2-19 Corrosion protection . . . . . . . . . . . . . . .7-5 Cruise control . . . . . . . . . . . . . . . . . .5-12 Cup holders . . . . . . . . . . . . . . . . . . .2-32 Curtain side-impact air bag system (See supplemental side air bag and curtain side-impact air bag system) . . . . . . . . . .1-27 D Daytime running light system (Canada only) . . . . . . . . . . . . . . . . Defroster switch Rear window and outside mirror defroster switch . . . . . . . . . . . . . Digital video disc DVD . . . . . . . . . . . Dimensions and weights . . . . . . . . . . Door locks . . . . . . . . . . . . . . . . . Door open warning light . . . . . . . . . . Drive belts . . . . . . . . . . . . . . . . . . Drive positioner, Automatic. . . . . . . . . Driving Cold weather driving . . . . . . . . . . Driving with automatic transmission. . Precautions when starting and driving DVD entertainment system . . . . . . . . . . .2-18 . . . . . . . .2-15 .4-44 . .9-8 . .3-3 . .2-7 .8-16 .3-25 . . . . .5-21 . .5-7 . .5-2 .4-44 E Economy - fuel . . . . . . . . . . . Emission control information label . Emission control system warranty . Engine Before starting the engine . . . Capacities and recommended fuel/lubricants. . . . . . . . . . Changing engine coolant . . . Changing engine oil . . . . . . Changing engine oil filter . . . . Checking engine coolant level. Checking engine oil level . . . . . . . . .5-14 . . . . . .9-10 . . . . . .9-19 . . . . . . .5-6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9-2 . .8-8 . .8-9 .8-10 . .8-7 . .8-8 Engine compartment check locations. . Engine coolant temperature gauge . . . Engine cooling system . . . . . . . . . . Engine oil . . . . . . . . . . . . . . . . . Engine oil and oil filter recommendation Engine oil viscosity . . . . . . . . . . . . Engine serial number . . . . . . . . . . . Engine specifications. . . . . . . . . . . Starting the engine . . . . . . . . . . . . Engine oil pressure low/engine coolant temperature high warning light . . . . . . . Exhaust gas (Carbon monoxide) . . . . . . Eyeglass case . . . . . . . . . . . . . . . . . . .8-7 . .2-4 . .8-7 . .8-8 . .9-5 . .9-5 .9-10 . .9-7 . .5-7 . .2-7 . .5-2 .2-28 F Flashers (See hazard warning flasher switch). . Flat tire . . . . . . . . . . . . . . . . . Floor mat positioning aid . . . . . . . . Fluid Automatic transmission fluid (ATF) Brake fluid . . . . . . . . . . . . . . Capacities and recommended fuel/lubricants. . . . . . . . . . . . Engine coolant . . . . . . . . . . . Engine oil . . . . . . . . . . . . . . Power steering fluid. . . . . . . . . Window washer fluid . . . . . . . . F.M.V.S.S. certification label . . . . . . Fog light switch . . . . . . . . . . . . . Front air bag system (See supplemental restraint system) . Front seats . . . . . . . . . . . . . . . . . . .2-20 . . . . .6-2 . . . . .7-4 . . . .8-11 . . . .8-13 . . . . . . . . . . . . . . . . . . . . . . .9-2 . .8-7 . .8-8 .8-13 .8-14 .9-10 .2-19 . . . .1-22 . . . . .1-2 10-2 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X Fuel Capacities and recommended fuel/lubricants. . . . . . . . . . Fuel economy . . . . . . . . . . Fuel filler cap . . . . . . . . . . Fuel filler lid . . . . . . . . . . . Fuel filler lid and cap . . . . . . Fuel gauge . . . . . . . . . . . Fuel octane rating . . . . . . . Fuel recommendation . . . . . Fuses . . . . . . . . . . . . . . . . Fusible links . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9-2 .5-14 .3-20 .3-20 .3-20 . .2-5 . .9-3 . .9-3 .8-23 .8-24 Headlight and turn signal switch. . . . . . . .2-15 Headlights . . . . . . . . . . . . . . . . . . . .8-26 Headphones (See DVD entertainment system) . . . . . . .4-47 Headrest storage . . . . . . . . . . . . . . . .2-34 Heated seats . . . . . . . . . . . . . . . . . .2-21 Heater Heater and air conditioner controls . . . . . . . . . . . . . . . .4-17, 4-27 Heater operation . . . . . . . . . . .4-19, 4-28 Rear seat air conditioner . . . . . . . . . .4-29 HomeLinkT Universal Transceiver . . . . . . .2-43 Hood release . . . . . . . . . . . . . . . . . .3-14 Horn . . . . . . . . . . . . . . . . . . . . . . .2-20 G Garage door opener, HomeLinkT Universal Transceiver . . . . . . . . . . . . . . . . . . Garment hook . . . . . . . . . . . . . . . . . Gas cap . . . . . . . . . . . . . . . . . . . . Gauge Engine coolant temperature gauge . . . Fuel gauge . . . . . . . . . . . . . . . . Odometer . . . . . . . . . . . . . . . . . Speedometer . . . . . . . . . . . . . . . Tachometer . . . . . . . . . . . . . . . . General maintenance . . . . . . . . . . . . Glove box . . . . . . . . . . . . . . . . . . . Glove box lock . . . . . . . . . . . . . . . . Grocery hooks . . . . . . . . . . . . . . . . I .2-43 .2-34 .3-20 . .2-4 . .2-5 . .2-4 . .2-4 . .2-4 . .8-2 .2-28 .2-28 .2-30 H Hazard warning flasher switch . . . . . . . . .2-20 Head restraints . . . . . . . . . . . . . . . . .1-10 Ignition switch . . . . . . . . . . . . . . . . . .5-5 Immobilizer system . . . . . . . . . .2-12, 3-2, 5-6 Important vehicle information label. . . . . . .9-10 In-cabin microfilter . . . . . . . . . . . . . . .8-18 Increasing fuel economy . . . . . . . . . . . .5-14 Indicator lights and audible reminders (See warning/indicator lights and audible reminders). . . . . . . . . . . . . . . . . . . . .2-6 Inside automatic anti-glare mirror . . . . . . .3-23 Inside mirror . . . . . . . . . . . . . . . . . . .3-23 Instrument brightness control . . . . . . . . .2-18 Instrument panel . . . . . . . . . . . . . . . . .2-2 Interior lights (see Lights on demand switch) . . . . . . . .2-41 ISOFIX child restraints . . . . . . . . . . . . .1-51 J Jump starting . . . . . . . . . . . . . . . . . . .6-7 K Key . . . . . . . . . . . . . . . . . . . . . . . .3-2 Keyless entry system (See remote keyless entry system) . . . . . . .3-9 L Labels Air conditioner specification label . . . . .9-11 Emission control information label . . . . .9-10 Engine serial number . . . . . . . . . . . .9-10 F.M.V.S.S. certification label . . . . . . . .9-10 Vehicle identification number (VIN) plate . .9-9 Warning labels (for SRS). . . . . . . . . .1-29 LATCH (Lower Anchors and Tethers for CHildren) System. . . . . . . . . . . . . . . . . . . . . .1-51 License plate Installing the license plate . . . . . . . . .9-11 Light Air bag warning light . . . . . . . . .1-30, 2-9 Brake light (See stop light). . . . . . . . .8-27 Bulb check/instrument panel . . . . . . . .2-6 Bulb replacement . . . . . . . . . . . . . .8-27 Charge warning light . . . . . . . . . . . . .2-7 Cornering light . . . . . . . . . . . . . . .2-19 Fog light switch . . . . . . . . . . . . . . .2-19 Headlight and turn signal switch. . . . . .2-15 10-3 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X Headlights . . . . . . . . . . . . . . . Light bulbs. . . . . . . . . . . . . . . Low tire pressure warning light . . . Low washer fluid warning light . . . Passenger air bag and status light. . Personal lights . . . . . . . . . . . . Security indicator light . . . . . . . . Warning/indicator lights and audible reminders . . . . . . . . . . . . . . . Lights Map lights . . . . . . . . . . . . . . . Lights on demand switch. . . . . . . . . Lock Back door release . . . . . . . . . . Child safety rear door lock . . . . . . Child safety sliding door lock . . . . Door locks . . . . . . . . . . . . . . Glove box lock . . . . . . . . . . . . Power door locks . . . . . . . . . . . Low fuel warning light . . . . . . . . . . Low tire pressure warning light . . . . . Low tire pressure warning system. . . . Low washer fluid warning light . . . . . Luggage (See vehicle loading information) . . . . . . . . . . . . . . . . . . .8-26 .8-26 . .2-8 . .2-9 .2-11 .2-42 .2-11 . . . .2-6 . . .2-43 . . .2-41 . . . . . . . . . . . . . . . . . . . . .3-18 . .3-9 . .3-9 . .3-3 .2-28 . .3-5 . .2-8 . .2-8 . .5-3 . .2-9 . . .9-12 M Main ON/OFF switch (for power doors) . . . . . . . . . . . . .3-6, 3-16 Maintenance General maintenance . . . . . . . . . . . .8-2 Inside the vehicle . . . . . . . . . . . . . . .8-3 Maintenance precautions . . . . . . . . . .8-5 Outside the vehicle. . . . . . . . . . . . . .8-2 Seat belt maintenance . . . . . . . Under the hood and vehicle . . . . Malfunction indicator lamp (MIL). . . . Manual front seat adjustment . . . . . Manual vent windows. . . . . . . . . . Map lights . . . . . . . . . . . . . . . . Map pocket . . . . . . . . . . . . . . . Meters and gauges. . . . . . . . . . . Instrument brightness control . . . Mirror Automatic anti-glare inside mirror . Inside mirror . . . . . . . . . . . . . Outside mirror control . . . . . . . Outside mirrors . . . . . . . . . . . Vanity mirror . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-40 . .8-4 .2-10 . .1-2 .2-38 .2-43 .2-29 . .2-3 .2-18 . . . . . . . . . . . . . . . .3-23 .3-23 .3-24 .3-24 .3-23 N Nissan vehicle immobilizer system (NVIS). . . . . . . . . . . . . . . . .2-12, 3-2, 5-6 Note holder . . . . . . . . . . . . . . . . . . .2-25 O Octane rating (See fuel octane rating) . . . Odometer . . . . . . . . . . . . . . . . . . . Oil Capacities and recommended fuel/lubricants. . . . . . . . . . . . . . . Changing engine oil . . . . . . . . . . . Changing engine oil filter . . . . . . . . . Checking engine oil level . . . . . . . . Engine oil . . . . . . . . . . . . . . . . . Engine oil and oil filter recommendation . .9-3 . .2-4 . .9-2 . .8-9 .8-10 . .8-8 . .8-8 . .9-5 Engine oil pressure low/engine coolant temperature high warning light . . . . . Engine oil viscosity . . . . . . . . . . . . Outside mirror control . . . . . . . . . . . . Outside mirrors . . . . . . . . . . . . . . . . Overdrive switch . . . . . . . . . . . . . . . Overheat If your vehicle overheats . . . . . . . . . Owner’s manual order form . . . . . . . . . Owner’s manual/service manual order information. . . . . . . . . . . . . . . . . . . . .2-7 . .9-5 .3-24 .3-24 .5-10 . .6-9 .9-21 .9-21 P Parking Parking brake check . . . . . . . . . . Parking brake operation . . . . . . . . Parking/parking on hills. . . . . . . . . Pedal position adjustment . . . . . . . . . Personal lights . . . . . . . . . . . . . . . Power Front seat adjustment . . . . . . . . . Power door locks . . . . . . . . . . . . Power outlet . . . . . . . . . . . . . . . Power steering fluid. . . . . . . . . . . Power steering system . . . . . . . . . Power vent windows . . . . . . . . . . Power windows . . . . . . . . . . . . . Precautions Maintenance precautions . . . . . . . Precautions on child restraints . . . . . Precautions on seat belt usage . . . . Precautions on supplemental restraint system . . . . . . . . . . . . . . . . . . Precautions when starting and driving 10-4 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X . . . . . .8-22 .5-11 .5-15 .3-22 .2-42 . . . . . . . . .1-5 . .3-5 .2-23 .8-13 .5-15 .2-38 .2-36 . . .8-5 . .1-40 . .1-31 . .1-15 . . .5-2 Pre-tensioner seat belt system. . . . . . . . .1-28 Push starting . . . . . . . . . . . . . . . . . . .6-9 R Radio Car phone or CB radio . . . . . . . . . . Compact Disc (CD) changer . . . . . . Rear audio controls . . . . . . . . . . . . Steering wheel audio control switch. . . Readiness for inspection maintenance (I/M) test . . . . . . . . . . . . . . . . . . . . . . . Rear audio controls . . . . . . . . . . . . . . Rear center seat belt . . . . . . . . . . . . . Rear seat air conditioner . . . . . . . . . . . Rear sonar system off switch . . . . . . . . Rear window and outside mirror defroster switch . . . . . . . . . . . . . . . . . . . . . Rear window wiper and washer switches. . Refrigerant recommendation . . . . . . . . Registering your vehicle in another country. Remote controller (See DVD entertainment system) . . . . . . Remote keyless entry system . . . . . . . . Reporting safety defects (US only) . . . . . .4-53 .4-39 .4-43 .4-41 .9-20 .4-43 .1-37 .4-29 .2-22 .2-15 .2-14 . .9-6 . .9-9 .4-46 . .3-9 .9-19 S Safety Child safety rear door lock . . . . . . . Child safety sliding door lock . . . . . Child seat belts . . . . . . . . . . . . . Reporting safety defects (US only) . . Screen (See DVD entertainment system) . . . . . . . .3-9 . .3-9 .1-40 .9-19 .4-46 Seat adjustment Front manual seat adjustment . . . . . . . .1-2 Front power seat adjustment . . . . . . . .1-5 Second row captain’s chair . . . . . . . . .1-6 Third row bench seat . . . . . . . . . .1-8, 1-9 Seat belt Child safety . . . . . . . . . . . . . . . . .1-33 Infants and small children . . . . . . . . .1-34 Injured Person. . . . . . . . . . . . . . . .1-34 Larger children . . . . . . . . . . . . . . .1-34 Precautions on seat belt usage . . . . . .1-31 Pregnant women . . . . . . . . . . . . . .1-34 Pre-tensioner seat belt system. . . . . . .1-28 Rear center seat belt . . . . . . . . . . . .1-37 Seat belt extenders . . . . . . . . . . . . .1-40 Seat belt maintenance . . . . . . . . . . .1-40 Seat belts . . . . . . . . . . . . . . . . . .1-31 Shoulder belt height adjustment . . . . . .1-39 Three-point type with retractor. . . . . . .1-35 Seat belt warning light . . . . . . . . . . . . . .2-9 Seatback pockets. . . . . . . . . . . . . . . .2-30 Seats Adjustment . . . . . . . . . . . . . . . . . .1-2 Automatic drive positioner . . . . . . . . .3-25 Front seats . . . . . . . . . . . . . . . . . .1-2 Heated seats . . . . . . . . . . . . . . . .2-21 Manual front seat adjustment . . . . . . . .1-2 Second row captain’s chair adjustment. . . . .1-6 Security indicator light . . . . . . . . . . . . .2-11 Security system (Nissan vehicle immobilizer system), engine start . . . . . . . . . . . . . .2-12, 3-2, 5-6 Self-adjusting brakes . . . . . . . . . . . . . .8-22 Service manual order form . . . . . . . . . . .9-21 Servicing air conditioner . . . . . . . . . . . .4-30 Shift lock release . . . . . . . . . . . . . . . . .5-9 Shifting Automatic transmission . . . . . . . . . . .5-8 Shoulder belt height adjustment . . . . . . . .1-39 Side air bag system (See supplemental side air bag and curtain side-impact air bag system) . . .1-27 Skyview™ roof . . . . . . . . . . . . . . . . . .2-39 Sliding door Manual sliding door . . . . . . . . . . . . .3-5 Power sliding door . . . . . . . . . . . . . .3-7 Sliding door locks Child safety sliding door locks. . . . . . . .3-9 Spark plug replacement . . . . . . . . . . . .8-17 Speedometer . . . . . . . . . . . . . . . . . . .2-4 SRS warning label . . . . . . . . . . . . . . .1-29 Starting Before starting the engine . . . . . . . . . .5-6 Jump starting . . . . . . . . . . . . . . . . .6-7 Precautions when starting and driving . . .5-2 Push starting . . . . . . . . . . . . . . . . .6-9 Starting the engine . . . . . . . . . . . . . .5-7 Steering Power steering fluid. . . . . . . . . . . . .8-13 Power steering system . . . . . . . . . . .5-15 Tilting steering wheel . . . . . . . . . . . .3-21 Steering wheel audio control switch. . . . . .4-41 Stop light . . . . . . . . . . . . . . . . . . . .8-27 Storage . . . . . . . . . . . . . . . . . . . . .2-25 Storage bin . . . . . . . . .2-27, 2-31, 2-33, 2-34 Storage compartment . . . . . . . . . . . . .2-25 Storage tray . . . . . . . . . . . . . . .2-26, 2-27 Sun visors . . . . . . . . . . . . . . . . . . . .3-22 Sunglasses case . . . . . . . . . . . . . . . .2-28 Sunglasses holder . . . . . . . . . . . . . . .2-28 Sunroof . . . . . . . . . . . . . . . . . . . . .2-39 Supplemental air bag warning labels . . . . .1-29 10-5 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X Supplemental air bag warning light . . .1-30, 2-9 Supplemental front impact air bag system . .1-22 Supplemental restraint system Information and warning labels. . . . . . .1-29 Precautions on supplemental restraint system . . . . . . . . . . . . . . .1-15 Supplemental restraint system (Supplemental air bag system). . . . . . . . .1-15 Supplemental side and curtain side-impact air bag system. . . . . . . . . . . . . . . . . .1-27 Switch Autolight switch . . . . . . . . . . . . . . .2-16 Automatic power window switch . . . . .2-37 Fog light switch . . . . . . . . . . . . . . .2-19 Hazard warning flasher switch . . . . . . .2-20 Headlight and turn signal switch. . . . . .2-15 Ignition switch . . . . . . . . . . . . . . . .5-5 Lights on demand switch. . . . . . . . . .2-41 Main ON/OFF switch (for power doors) . . . . . . . . . . .3-6, 3-16 Overdrive switch . . . . . . . . . . . . . .5-10 Power door lock switch . . . . . . . . . . .3-5 Rear sonar system off switch . . . . . . .2-22 Rear window and outside mirror defroster switch . . . . . . . . . . . . . . .2-15 Rear window wiper and washer switches . . . . . . . . . . . . . . . . . . .2-14 Traction control system (TCS) off switch . . . . . . . . . . . . . . . . . . . .2-22 Vehicle dynamic control (VDC) off switch . . . . . . . . . . . . . . . . . . . .2-22 Windshield wiper and washer switch . . .2-13 T Tachometer . . . . . . . . . . . . . . . . . . . .2-4 Temperature gauge Engine coolant temperature gauge . . . . .2-4 Engine oil pressure low/engine coolant temperature high warning light . . . . . . .2-7 Theft (Nissan vehicle immobilizer system), engine start . . . . . . . . . . . . . .2-12, 3-2, 5-6 Third row bench seat adjustment . . . . .1-8, 1-9 Three-way catalyst . . . . . . . . . . . . . . . .5-2 Tilting steering wheel . . . . . . . . . . . . . .3-21 Tire Flat tire . . . . . . . . . . . . . . . . . . . .6-2 Spare tire. . . . . . . . . . . . . . . .6-3, 8-39 Tire chains . . . . . . . . . . . . . . . . . .8-36 Tire placard . . . . . . . . . . . . . . . . .9-11 Tire pressure . . . . . . . . . . . . . . . .8-31 Tire rotation . . . . . . . . . . . . . . . . .8-37 Types of tires . . . . . . . . . . . . . . . .8-36 Uniform tire quality grading. . . . . . . . .9-18 Wheels and tires . . . . . . . . . . . . . .8-31 Wheel/tire size . . . . . . . . . . . . . . . .9-8 Tire pressure Low tire pressure warning light . . . . . . .2-8 Top tether strap child restraint . . . . . . . . .1-53 Towing Flat towing. . . . . . . . . . . . . . . . . .9-17 Tow truck towing . . . . . . . . . . . . . .6-10 Towing load/specification chart . . . . . .9-15 Trailer towing . . . . . . . . . . . . . . . .9-14 Traction control system (TCS) off switch . . .2-22 Transceiver HomeLinkT Universal Transceiver . . . . .2-43 Transmission Automatic transmission fluid (ATF) . . . .8-11 Driving with automatic transmission. . . . .5-7 Selector lever lock release . . . . . . . . . .5-9 Travel (See registering your vehicle in another country) . . . . . . . . . . . . . . . . . . . . . .9-9 Turn signal switch (See headlight and turn signal switch) . . . . . . . . . . . .2-15, 2-19 U Umbrella holder . . . . . . . . . . . . . . . . .2-30 Uniform tire quality grading. . . . . . . . . . .9-18 V Vanity mirror . . . . . . . . . . . . . . . . . . .3-23 Vehicle dimensions and weights . . . . . . . .9-8 Vehicle dynamic control (VDC) off switch. . .2-22 Vehicle dynamic control (VDC) system . . . .5-19 Vehicle identification . . . . . . . . . . . . . . .9-9 Vehicle identification number (VIN) (Chassis number). . . . . . . . . . . . . . . . .9-9 Vehicle identification number (VIN) plate . . . .9-9 Vehicle loading information. . . . . . . . . . .9-12 Vehicle recovery . . . . . . . . . . . . . .6-12, 7-2 Vehicle security system (Nissan vehicle immobilizer system), engine start . . . . . . . . . . . . . .2-12, 3-2, 5-6 Ventilators . . . . . . . . . . . . . . . . . . . .4-17 Visors . . . . . . . . . . . . . . . . . . . . . .3-22 10-6 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X W Warning Air bag warning light . . . . . . . . .1-30, 2-9 Anti-lock brake warning light . . . . . . . .2-6 Battery charge warning light . . . . . . . . .2-7 Brake warning light . . . . . . . . . . . . . .2-7 Door open warning light . . . . . . . . . . .2-7 Engine oil pressure low/engine coolant temperature high warning light . . . . . . .2-7 Hazard warning flasher switch . . . . . . .2-20 Low fuel warning light . . . . . . . . . . . .2-8 Low tire pressure warning light . . . . . . .2-8 Low washer fluid warning light . . . . . . .2-9 Seat belt warning light . . . . . . . . . . . .2-8 Warning labels (for SRS). . . . . . . . . .1-29 Warning/indicator lights and audible reminders . . . . . . . . . . . . . . . . . . .2-6 Warning lights . . . . . . . . . . . . . . . . . .2-6 Washer switch Rear window wiper and washer switches . . . . . . . . . . . . . . . . . . .2-14 Windshield wiper and washer switch . . .2-13 Weights (See dimensions and weights) . . . .9-8 Wheels and tires . . . . . . . . . . . . . . . .8-31 Wheel/tire size . . . . . . . . . . . . . . . . . .9-8 When traveling or registering your vehicle in another country . . . . . . . . . . . . . . . .9-9 Window washer fluid . . . . . . . . . . . . . .8-14 Windows Locking passengers’ windows . . . . . . .2-37 Manual vent windows. . . . . . . . . . . .2-38 Power vent windows . . . . . . . . . . . .2-38 Power windows . . . . . . . . . . . . . . .2-36 Windshield wiper and washer switch . . . . .2-13 Wiper Rear window wiper and washer switches . . . . . . . . . . . . . . . . . . .2-14 Windshield wiper and washer switch . . .2-13 Wiper blades . . . . . . . . . . . . . . . .8-19 10-7 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X MEMO MEMO MEMO GAS STATION INFORMATION RECOMMENDED FUEL: TIRE COLD PRESSURE: Use unleaded regular gasoline with an octane rating of at least 87 AKI (Anti-Knock Index) number (Research octane number 91). See Tire and Loading Information label. CAUTION ● Using a fuel other than that specified could adversely affect the emission control system, and may also affect the warranty coverage. ● Under no circumstances should a leaded gasoline be used, because this will damage the three-way catalyst. RECOMMENDED NEW VEHICLE BREAK-IN PROCEDURE: During the first 1,200 miles (2,000 km) of vehicle use, follow the recommendations outlined in the “BREAK-IN SCHEDULE” information found in the “Starting and driving” section of this manual. Follow these recommendations for the future reliability and economy of your new vehicle. Failure to follow these recommendations may result in vehicle damage or shortened engine life. For additional information, see “Capacities and recommended fuel/lubricants in the “Technical and consumer information” section. RECOMMENDED ENGINE OIL: ● API Certification Mark ● API grade SL, Energy Conserving ● ILSAC grade GF-III ● 5W-30 Viscosity preferred See “Engine oil and oil filter recommendation” in the “Technical and consumer information” section of this manual. Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X QUICK REFERENCE 1. Engine oil 8-8 2. Window washer fluid 8-14 3. Engine coolant 8-7 4. Power steering fluid 8-13 5. Meters and gauges 2-3 6. Audio system 4-30; Climate controls 4-17, 4-27 7. Spare tire 6-2 8. Fuel filler lid release 3-20; Fuel recommendation 9-3 9. Keys 3-2 10. Seat belts 1-31 11. Front seats 1-2 12. Hood release 3-14 13. Brake fluid 8-14 14. Battery 8-15 15. Automatic transmission fluid 8-11, 8-12 LGS0019 Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X