Chevrolet - Sonic - Wiring Diagram - 2020 - 2020

11258 2012-PRESENT CHEVROLET SONIC HATCHBACK 6/22/2020 GROSS LOAD CAPACITY WHEN USED AS A WEIGHT CARRYING HITCH: 2000 LBS. TRAILER WEIGHT & 200 LBS. TONGUE WEIGHT. ***DO NOT EXCEED VEHICLE MANUFACTURER'S RECOMMENDED TOWING CAPACITY.*** WARNING: ALL NON-TRAILER LOADS APPLIED TO THIS PRODUCT MUST BE SUPPORTED BY 18050 STABILIZING STRAPS. ** FAILURE TO PROPERLY SUPPORT NON-TRAILER LOADS WILL VOID PRODUCT WARRANTY** HAVING INSTALLATION QUESTIONS? CALL TECHNICAL SUPPORT AT 1-877-287-8634 Parts List ITEM QTY PART NUMBER 1 DESCRIPTION 1 4 10-10282 BOLT,CAR,7/16-14 UNC,1-1/2,GRD8,YZ 2 4 CM-SP2 .250 x .88 x 2.25" SQUARE HOLE SPACER 3 4 20-00103 NUT,SER-FLANGE,7/16-14 UNC,GRD8,YZ 4 4 7_16 FISHWIRE 7/16" FISHWIRE PASSENGER FRAME RAIL 2 ACCESS HOLE 4 DRIVER FRAME RAIL ACCESS HOLE VEHICLE MUFFLER DESIGNED FOR USE WITH BALLMOUNT D-55001/45501 3 EURO MOUNT OPTION AVAILABLE #45571 (1 7/8" BALL) & #45572 (2" BALL) HITCH WEIGHT: 34 LBS. INSTALL TIME PROFESSIONAL: 20 MINUTES NOVICE (DIY): 45 MINUTES INSTALL NOTES: -No Drilling Required -Fishwire Hardware TOOLS REQUIRED RATCHET 11/16" SOCKET TORQUE WRENCH INSTALLATION STEPS 1. Fishwire CM-SP2 spacers and 7/16-14 carriage bolts through access holes and into attaching holes. Leave fishwires attached. Note: Driver side requires reverse fishwire for rearmost fastener. 2. Raise hitch into position, being careful not to push bolts back into frame. 3. Remove fishwires. Secure with 7/16-14 flange hex nuts. 4. Torque all 7/16-14 fasteners to 70 ft.-lbs. PERIODICALLY CHECK THIS RECEIVER HITCH TO ENSURE THAT ALL FASTENERS ARE TIGHT AND THAT ALL STRUCTURAL COMPONENTS ARE SOUND. Curt Manufacturing LLC., warrants this product to be free of defects in material and/or workmanship at the time of retail purchase by the original purchaser. If the product is found to be defective, Curt Manufacturing LLC., may repair or replace the product, at their option, when the product is returned, prepaid, with proof of purchase. Alteration to, misuse of, or improper installation of this product voids the warranty. Curt Manufacturing LLC.'s liability is limited to repair or replacement of products found to be defective, and specifically excludes liability for incidental or consequential loss or damage. 11258 YEARS: 2012-PRESENT Safety glasses should be worn at all times while installing this product . INSTALLATION INSTRUCTIONS MAKE: CHEVROLET MODEL: SONIC STYLE: HATCHBACK WARNING: NEVER EXCEED YOUR VEHICLE MANUFACTURER'S RECOMMENDED TOWING CAPACITY WEIGHT CARRYING: INSTALLATION TIME: TRAILER WEIGHT: TONGUE WEIGHT: 20 MIN. THE INSTALL TIME LISTED IS FOR PROFESSIONAL INSTALLERS. IF YOU ARE HESITANT TO UNDERTAKE THIS TASK ON YOUR OWN, CONTACT AN AUTHORIZED CURT INSTALLER FOR ADDITIONAL ASSISTANCE. INSTALLATION REQUIRES: 11/16" 2000 200 WARNING: WE RECOMMEND THE USE OF 18050 STABILIZING STRAPS FOR ALL NON-TRAILER (WHEEL-LESS) LOADS. PLEASE SEE THE CURT CATALOG OR VISIT US ONLINE AT WWW.CURTMFG.COM FOR FURTHER INFORMATION. LBS. LBS. INSTALLATION TIPS: 1. BEFORE YOU BEGIN INSTALLATION, READ ALL INSTRUCTIONS THOROUGHLY. 2. TO EASE INSTALLATION, 2 PEOPLE MAY BE REQUIRED. 3. USING PROPER TOOLS WILL GREATLY IMPROVE THE QUALITY OF THE INSTALL AND REDUCE THE TIME REQUIRED. 4. NEED HELP OR HAVE SOME QUESTIONS? CALL TECHNICAL SUPPORT AT 877.287.8634 LEVEL OF DIFFICULTY: RATCHET SOCKET TORQUE WRENCH VEHICLE PHOTO: EASY MODERATE EASY CHALLENGING FISHWIRE HARDWARE REPRESENTATIVE PHOTO HITCH ILLUSTRATION: NO DRILLING REQUIRED REVERSE FISHWIRING REQUIRED MAKE SURE YOUR HITCH MATCHES PERIODICALLY CHECK THIS RECEIVER HITCH TO ENSURE ALL FASTENERS ARE TIGHT AND ALL STRUCTURAL COMPONENTS ARE SOUND CURT Manufacturing LLC. warrants this product to be free of defects in material and/or workmanship at the time of retail purchase by the original purchaser. If the product is found to be defective, Curt Manufacturing LLC. may repair or replace the product at their option, when the product is returned, prepaid, with proof of purchase. Alteration to, misuse of, or improper installation of this product voids the warranty. Curt Manufacturing LLC.'s liability is limited to repair or replacement of products found to be defective, and specifically excludes liability for incidental or consequential loss or damage. For more information log onto www.curtmfg.com, & for helpful towing tips log onto www.hitchinfo.com 6/22/2020 INSTALLATION WALKTHROUGH: Parts List ITEM QTY PART NUMBER DESCRIPTION 1 4 10-10282 BOLT,CAR,7/16-14 UNC,1-1/2,GRD8,YZ 2 4 CM-SP2 .250 x .88 x 2.25" SQUARE HOLE SPACER 3 4 20-00103 NUT,SER-FLANGE,7/16-14 UNC,GRD8,YZ 4 4 7_16 FISHWIRE 7/16" FISHWIRE 1. Fishwire CM-SP2 spacers and 7/16-14 carriage bolts through access holes and into attaching holes. Leave fishwires attached. Note: Driver side requires reverse fishwire for rearmost fastener. 1 2 PASSENGER FRAME RAIL DRIVER FRAME RAIL ACCESS HOLE 4 ACCESS HOLE 2. Raise hitch into position, being careful not to push bolts back into frame. VEHICLE MUFFLER 3. Remove fishwires. Secure with 7/16-14 flanged nuts. 4. Torque all 7/16-14 fasteners to 70 ft.-lbs. Installation is complete. 3 EURO MOUNT OPTION AVAILABLE #45571 (1 7/8" BALL) & #45572 (2" BALL) DESIGNED FOR USE WITH BALLMOUNT D-55001/45501 For more information log onto www.curtmfg.com, & for helpful towing tips log onto www.hitchinfo.com