BMW - M3 Coupe (E92) - Wiring Diagram - 2008 - 2013

REMOTE ENGINE START MODULE Pandora BMW Bypass Micro-USB port Small-size interface module for bypass of an original immobilizer (Car Access System CAS3) is designed to control engines of BMW/MINI cars with a Start/Stop button and a slot for an original key. Control over the module and engine start procedure is performed only by Pandora security systems with an IMMO-KEY port. LED BP indicator Supported systems: Pandora Professional v2 (DXL 5000L v2), Pandora Smart Pro (DXL 1940L, DXL 1920/1930L), Pandora Smart (DXL 1840L), Pandora Light Pro (DXL 1090L). VALET BP button LIST OF SUPPORTED CARS Brand Model Years Model code BMW 1 Series (E82/88) 2008-2013 1 M (E82) Brand Model Years 5111 X1 (E84) 2012-2013 5111 2008-2013 5111 X5 (E70) 2008-2013 5111 / 5113 3 Series Sedan (E90/91) 2006-2011 5111 X5 M (E70) 2010-2013 5111 / 5113 3 Series Coupe (E92/93) 2007-2013 5111 X6 (E71/72) 2008-2013 5111 / 5113 M3 Sedan (E90) 2008-2011 5111 X6 M (E71/72) 2010-2013 5111 / 5113 M3 Coupe (E92/93) 2008-2013 5111 Z4 (E89) 2009-2013 5111 5 Series (E60/61) 2005-2010 5111 / 5112 Cooper 2007-2013 5111 M5 (E60/61) 2006-2010 5111 / 5112 Cooper Convertible 2008-2013 5111 6 Series (E63/64) 2005-2010 5111 / 5112 Clubman 2008-2013 5111 M6 (E63/64) 2006-2010 5111 / 5112 Coupe / Roadster 2012-2013 5111 MINI Model code CONNECTION DIAGRAM micro USB LED BP X1 2 1 X2 Black Red «Ground» «+12V Power» Remove if the connector mismatches X5 X6 X3 3 2 1 Green IMMO-KEY1 OUT White Black IMMO-KEY2 OUT To a base unit of Pandora X4 VALET BP C1 4 3 2 1 Red Black White Green Red Black White Green Brown/Gray 1 2 3 Blue/Red 4 Purple/Yellow B1 Brown/Black CAR ACCESS SYSTEM CAS3 X4 X3 X2 CONNECTOR B1: BMW: The module is located behind the steering wheel column MINI: The module is located under the dashboard on the driver side Connections in the B1 connector: Pin34 - «+12V» Pin12 – «Ground» Pin35 – CAN1High Pin26 – CAN1Low WARNING! Location of the wires in the B connector can be different. To a base unit of Pandora Professional 4 3 2 1 Brake pedal switch (Automatic transmission) 4 3 2 1 Red Black White WARNING! Collors and location of the brake/clutch pedal wires can be different. Green Purple/Yellow 1 2 3 Blue/Black 4 Brown/Black Blue/Brown Clutch pedal switch (Manual transmission) WARNING! This manual has the status of a reccomendation. Configuration, connection and installation of the system must be performed by highly qualified specialists. WARNING! The system installation should be performed when the system sockets and the negative battery terminal are disconnected. WARNING! It is required to update firmware of the remote engine start module before the installation. REMOTE ENGINE START WITH THE BMW BYPASS MODULE «Program neutral» procedure (reservation mode for mechanical transmission) If a car has a manual gearbox, the “Program neutral” procedure is required for remote and automatic engine starts. This procedure can be activated automatically by handbrake or manually by pressing and holding the “Arm” button on a remote control when handbrake is activated (it depends on the settings). The engine must be running for 30 seconds and more to activate the “Program neutral”. - Do not switch off the ignition, fixate a car by the handbrake and put a gear lever to the neutral position. - The key slot will be unlocked when the “Program neutral” is activated - Do not press the START/STOP button, press the original key and remove it from the slot. - Leave the car, close the doors. NOTE! There is a setting “Switch on neutral when the last door is closed”. It allows to stop the engine after closing the last door (not after arming). If a door is opened after stopping the engine and before arming, the “program neutral” will be deactivated. - Arm the system, the engine will be stopped and the system will be ready for remote engine start. NOTE! The bypass module allows using “Turbotimer” and “Ignition backing” functions. Remote and automatic engine start The way to start the engine depends on the type of system (see the User manual). The module allows not to stop the engine when disarming. To do this, disarm the system during a remote engine start procedure, insert a key into the key slot and hold it for 3-5 seconds (until it is fixed). Control over the engine will be delegeted to the car original systems. After this you can start driving. WIRING DESCRIPTION Х2 Socket (power supply) • Wire №1 (Red) (+12V) — “Power supply” of the module. It connects to a realiable wire with constant +12V. • Wire №2 (Black) (-) — “Ground”. It connects to a grounding spot of a car. This wire must be connected first during installation. Х3 Socket(module control) This socket is used to connect the module with a Pandora system. • Wire №1 (Black) — It connects to the IMMO-KEY2 OUT of a Pandora system. • Wire №2 (White) — This wire is not used. • Wire №3 (Green) — It connects to the IMMO-KEY1 OUT of a Pandora system. Х4 Socket (brake/clutch pedal control) This socket is used for brake (automatic transmission)/clutch (mechanical transmission) switch connections. X5 and X6 sockets (bypass of CAS3 immobilizer) This sockets are used for «pin-to-pin» connection to the original wires of a CAS3 module. INSTRUCTIONS 1. Configure a base unit of Pandora system using the Alarm Studio: - select a model code; - select a transmission Type (Automatic or Manual) in the “Automatic start” settings, enable the “Car with Start/Stop button” and “Enable bypass when engine is running” settings; - select the “BMW CAS3 bypass” in the “Original immobilizer bypass” settings. 2. Connect the module to a car and to the base unit of Pandora system. 3. Make bypass learning procedure: - enter the level 17 of the programming menu, the LED of the system and the LED BP of the module will light green; - insert an original key into the key slot, wait until the LED BP becomes orange, remove the key from the key slot; - wait until the LED BP becomes green, insert an original key into the key slot, wait until the LED BP becomes orange, remove the key from the key slot; - wait until the LED of the system starts flashing green, press the VALET button of the base unit of the system, disconnect all connectors from the base unit and make the Cloning procedure. 4. Make Cloning procedure: - connect the base unit of the system to a PC by a USB-cable; - enter the programming mode by entering the “Service PIN-code”; - run the Pandora Alarm Studio and log in; - confirm data transmission, wait for the procedure to be finished. - the system is ready to work, connect the base unit to the connectors. UPDATING FIRMWARE • Run the Pandora Alarm Studio on a PC, connect a USB cable to it. • Disconnect the power supply from the module. Press and hold the VALET BP button, connect the USB cable to the module, release the button after connecting – the module will enter the boot mode. • Upload firmware to the module. Disconnect the USB cable after updating. TECHNICAL SPECIFICATIONS Voltage ...........................................................................................12V Current consumption ...............................................................0,5mA Dimensions...................................................................................50х74х17 mm