BMW - X325 - Workshop Manual - 2002 - 2002

BMW Parts and Accessories Installation Instructions F 39 1035 B BMW CD changer installation kit BMW 5 Series touring (E 39/2) These installation instructions are only valid for cars with a production date before 09/01 Technical and electrical knowledge required The installation time is 0.5 - 3.5 hours but this may vary depending on the condition of the car and the equipment in it. Retrofit/Installation kit No. 65 12 0 029 646 65 12 0 029 594 65 12 0 140 742 65 12 0 140 743 Retrofit / Installation kit No. 65 12 0 029 646 (others see cover sheet) Installation Instructions No. 01 29 0 029 575 Issue date: 05.2002 Contents Section Page 1. Important information on installing the CD changer in the E39/2 . . . . . . . . . . . . . . . 3 2. Preparations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 3. Parts list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 4. Connection diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 5. Installation and cabling diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 6. To install the CD changer (cars without an on-board monitor, without a DSP amplifier and with Professional radio SA663 up to production date 02/01 only). . . . . . . . . . . 10 7. To install the CD changer (cars without an on-board monitor, without a DSP amplifier and with Professional radio SA663 after production date 03/01 only) . . . . . . . . . . . 13 8. To install the CD changer (cars with an on-board monitor and without a DSP amplifier only) . . . . . . . . . . . . . . 17 To install the CD changer (cars with a DSP amplifier only) . . . . . . . . . . . . . . . . . . . . 20 10. To install the CD changer (cars with CD changer preparation only) . . . . . . . . . . . . . 22 11. Coding and concluding work . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 12. Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 13. Circuit diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 9. Retrofit / Installation kit No. 65 12 0 029 646 (others see cover sheet) Installation Instructions No. 01 29 0 029 575 Issue date: 05.2001 1. Important information on installing the CD changer in the E39/2 Only for use in the BMW dealer organisation. The CD changer may only be installed by a specialist workshop that has the required special tools and manuals (servicing, repair, diagnostics, etc.). All the work is shown for the left-hand side of the car and must be repeated on the righthand side. In cars with an on-board monitor radio the control cable is only installed in the boot.  In cars with a BMW Professional hi-fi system DSP amplifier only the coaxial cable for the Professional hi-fi system DSP amplifier/CD change must be installed in the boot.  Ensure that the cables/lines are not kinked or damaged as you install them in the car. Additional cables/leads that you install must be secured with cable ties.If the specified PIN chambers are occupied, bridges, double crimps or twin-lead terminals must be used. Subject to technical modifications Required tools and equipment Set of flat screwdrivers Set of Philips screwdrivers Angle cutter 1/4 inch socket set Cable lamp BMW disconnection tool Hot air blower Set of Allen keys Drill Set of drill bits 1/2 inch socket set Set of step drill bits Set of Torx sockets Retrofit / Installation kit No. 65 12 0 029 646 (others see cover sheet) Installation Instructions No. 01 29 0 029 575 Issue date: 05.2002 EN/3 2. Preparations TIS instruction No. 12 00 ... 51 47 151 - Print out error memory Disconnect the battery Remove the left boot trim Remove the boot floor or load compartment floor Remove the on-board tool holder Additional preparations for cars with an on-board monitor radio Remove the cover on the on-board monitor radio - Additional preparations for cars without a power supply Remove the right boot trim Remove the cover on the on-board monitor radio - Additional preparations for cars without Professional hi-fi system DSP amplifier and on-board monitor Remove the front left seat Remove the door sill strips at the front and rear left. Remove the B pillar trim on the left Remove the rear seat bench and rear seat backrest Remove the front left centre console trim Remove the components in the centre console (radio, cassette, heating/air conditioning control) to release the centre console and push it back a little Remove the boot floor carpet and wheel arch cover on the left Remove the boot floor carpet at both sides near the spare wheel trough Remove the cover on the on-board monitor radio Remove the on-board tool holder Retrofit / Installation kit No. 65 12 0 029 646 (others see cover sheet) Installation Instructions No. 01 29 0 029 575 Issue date: 05.2002 52 14 000 51 47 030 51 47 000 51 43 150 51 43 148 52 24 005 52 26 015 65 11 030 65 52 510 61 31 057 64 11 749 51 47 101 51 47 102 51 47 151 51 47 131 65 52 510 - EN/4 3. Parts list 1 4 5 2 6 3 7 8 9 10 15 11 16 12 17 13 18 14 19 F 39 1012 B Retrofit / Installation kit No. 65 12 0 029 646 (others see cover sheet) Installation Instructions No. 01 29 0 029 575 Issue date: 05.2002 EN/5 3. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 Parts list CD changer Shrink hose* CD changer coaxial cable (620 mm)****** Power supply cable CD changer control cable (5200 mm)*/*** CD changer control cable (1,300 mm)*/** CD changer adapter cable*/**** Base holder CD changer holder Expanding nut Plastic cap nut M5 (2x) Fillister head Philips screw (4x) Hexagonal self-tapping screw Cable tie (L=292 mm W=4 mm) (20x) Cable tie (L=200 mm W=3 mm) (2x) Cable holder Socket casing (2x) Speed nut M5 (3x) Retaining clip***** * ** Part not required for cars with a DSP amplifier Part not required for cars with an on-board monitor radio with a production date after 09/01 *** Part not required for cars without an on-board monitor radio with a production date after 09/00 **** Part not required for cars with a Professional radio SA663 with a production date before 02/01 ***** Part only required for cars with a Professional radio SA663 with a production date before 02/01 ****** Part only required for cars with a DSP amplifier Retrofit / Installation kit No. 65 12 0 029 646 (others see cover sheet) Installation Instructions No. 01 29 0 029 575 Issue date: 05.2002 EN/6 4. Connection overview A3 17 A2 A4 A1 A B2 B1 B C2 C1 C D2 D1 D E2 E1 E F 39 1013 B Power supply cable A is only required if the black 3-pin socket casing for the CD changer power supply is not tied back on the audio wiring harness Item Description Cable colour Connection location in the car --- ---- Dimensio ns: Power supply cable A1 Cable eyelet, 6 mm in diameter, terminal 30 brown Earth post X13016 on the left tail light A2 Black 1-pin plug casing X6500 with twin-lead terminal I-BUS white/grey/ yellow To audio systems plug connector X322B in the boot on the left side panel, black 12-pin socket casing PIN4, white/grey/ yellow cable A3 Black 1-pin plug casing X6501 with twin-lead terminal 30 A56 red/green To audio systems plug connector X322B in the boot on the right side panel, black 12-pin socket casing PIN1, red/green cable A4 Black 3-pin socket casing 17 Black 1-pole socket casing --- Power supply connector X18180 for CD changer in the boot on the left --- To the disconnected socket contacts from the audio systems plug connector X322B in the boot on the left side panel and X325B in the boot on the right side panel Retrofit / Installation kit No. 65 12 0 029 646 (others see cover sheet) Installation Instructions No. 01 29 0 029 575 Issue date: 05.2002 EN/7 4. Connection overview Control cable B is only required for cars without an on-board monitor and without a Professional hi-fi system DSP amplifier Item Description B Control cable Radio/CD changer B1 Silver 10-pin socket casing Cable colour Connection location in the car --- ---- Black 6-pin socket casing B2 --- To silver 10-pin plug casing E2 on the adapter cable or, on cars with a Professional radio SA663 with a production date before 02/01, to the black 17-pin radio socket casing --- To the CD changer in the boot on the left Control cable C is only required for cars with an on-board monitor and without a Professional hi-fi system DSP amplifier Item Description Cable colour Connection location in the car C Control cable On-board monitor radio/CD changer --- ---- C1 Silver 10-pin socket casing --- To silver 10-pin control casing E2 on the adapter cable E C2 Black 6-pin socket casing --- To the CD changer in the boot on the left Coaxial cable D is only required for cars with a Professional hi-fi system DSP amplifier Item Description D Coaxial cable D1 Angled coaxial socket casing D2 Coaxial socket casing Cable colour Connection location in the car --- ---- --- To the Professional hi-fi system DSP amplifier in the boot on the left --- To the CD changer in the boot on the left Adapter cable E is only required for cars without a Professional hi-fi system DSP amplifier. Adapter cable E is not required for cars with Radio Professional radio SA663 with a production before 02/01. Item Description E Adapter cable E1 White 12-pin socket casing E2 Silver 10-pin plug casing Cable colour Connection location in the car --- ---- --- To the new generation radio connection plug at the front or the new generation on-board monitor radio at the rear --- To the silver 10-pin socket casing B1 on the control cable B or to the silver 10-pin socket casing C1 on the control cable C Retrofit / Installation kit No. 65 12 0 029 646 (others see cover sheet) Installation Instructions No. 01 29 0 029 575 Issue date: 05.2002 EN/8 5. Installation and cabling diagram 0 A3 E2 A E1 C1 B E B1 A4 B2 E2 A1 C E1 C2 D2 A2 D1 F 39 1014 B The power supply wiring harness A, the control cable B, the control cable C, the coaxial cable D and the adapter cable E are to be installed as shown in the figure and secured with cable ties. When installing the power supply wiring harness A start with branches A1 and A2 . Branches A1 and A2 to the left side panel in the boot Branch A3 to the right side panel in the boot Branch A4 to the CD changer in the boot on the left Branch B1 to the installation site of the radio / connect to branch E2 Branch B2 to the CD changer in the boot on the left Connect branch C1 to branch E2 Branch C2 to the CD changer in the boot on the left Branch D1 to the DSP amplifier in the boot on the left Branch D2 to the CD changer in the boot on the left Branch E1 to the new generation connection plug on radio at the front or the new generation connection plug on the on-board monitor radio at the rear Branch E2 to the connection plug on the control cable B or branchC Retrofit / Installation kit No. 65 12 0 029 646 (others see cover sheet) Installation Instructions No. 01 29 0 029 575 Issue date: 05.2002 EN/9 6. To install the CD changer (cars without an on-board monitor, without a DSP amplifier and with Professional radio SA663 up to production date 02/01 only) 0 The installation of the power supply cable A for the CD change is only necessary, if the black 3-pin socket casing X18180 on the power supply for the CD changer is not tied back on the audio wiring harness. A X18180 F 39 1015 B 0 A1 30 X13016 Disconnect the black 12-pin plug connector X322 (30). Connect branch A2, white/grey/yellow cable on the power supply cable A, to slot PIN4. Press the contact socket out of plug connector X322 (30) and connect the twin-lead terminal to the 1-pin black socket casing (17). Screw the cable eyelet A1 to earth post X13016 under the left tail light. Lay the power supply cable A parallel to the standard wiring harness to the installation site of the CD changer. F 39 1016 B 0 A X325 30 oo o o oo ooooo oo Disconnect plug connector X325. Connect branch A3, red/green cable on the power supply cable A, to slot PIN1. To do this press the contact socket out of plug connector X325 and connect the twin-lead terminal to the 1-pin black socket casing (17). o ooo oo oo ooo o Lay branch A3, black 1-pin plug casing, along the wiring harness (30) on the boot floor from left to right to the tied back black 1-pin plug connector X325 and secure it. o oo ooo oooooo oo o F 39 1017 B 0 The installation of the control cable B for the CD changer is only required, if the black 6-pin socket casing X18729 on the control cable for the CD changer is not tied back on the audio wiring harness. B X18729 F 39 1018 B Retrofit / Installation kit No. 65 12 0 029 646 (others see cover sheet) Installation Instructions No. 01 29 0 029 575 Issue date: 05.2002 EN/10 6. To install the CD changer (cars without an on-board monitor, without a DSP amplifier and with Professional radio SA663 up to production date 02/01 only) 0 30 31 32 33 35 Thread the control cable B from the radio (30) on the left under the centre console (31) between the gearbox tunnel (32) and carpet along the floor panel cross traverse (33). Lay the control cable B along the standard wiring harness near the sill (34) to the installation site of the CD changer (35) in the boot on the left. Secure the control cable B with cable ties. E B 34 F 39 1020 B 0 X18126 19 B1 B 30 Connect branch B1, silver 12-pin socket casing on the control cable B to the black 17-pin socket casing X18126 on the radio connection plug and secure it with a retaining clip (19). Connect socket casing X18126 to the radio (30). 039 0003 B 0 The figure shows the boot at the rear left. Push the expanding nut (10) into the existing hole (30). 30 F 39 1022 B 10 11 0 Insert the base holder (8) and secure it with the hexagonal self-tapping screw (13) and two cap nuts M5 (11). 11 8 13 F 39 1023 B Retrofit / Installation kit No. 65 12 0 029 646 (others see cover sheet) Installation Instructions No. 01 29 0 029 575 Issue date: 05.2002 EN/11 6. To install the CD changer (cars without an on-board monitor, without a DSP amplifier and with Professional radio SA663 up to production date 02/01 only) 0 30 V V H H Remove the three transport guard screws (30) from the CD changer (1) and seal the apertures with the adhesive discs supplied (adhesive discs are supplied with the CD changer). Remove the two covers (31) and set the adjustment mechanism (32) with a straight slot screwdriver to V (vertical installation) and then reaffix both covers (31). 1 31 31 32 F 39 1024 B 0 A4/X18180 30 31 A Connect branch A4, black 3-pin socket casing on the power supply cable A or the standard power supply plug X18180 to the plug casing on the power supply connector (30) on the CD changer (1). Connect branch B2, black 6-pin socket casing on the control cable B or the standard plug X18729 to the plug casing (31) on the CD changer (1). 1 B B2/X18729 F 39 1025 B 0 12 12 18 1 30 8 9 Insert the CD changer (1) into the holder (9) and secure it with the four fillister head Philips screws (12). Secure the connection cable for the CD changer (1) with the holder (16) to the hole (31) from the inside. Place the CD changer (1) with the holder (9) on the base holder (8) and secure it with three collar nuts M5 (18). 16 F 39 1026 B Retrofit / Installation kit No. 65 12 0 029 646 (others see cover sheet) Installation Instructions No. 01 29 0 029 575 Issue date: 05.2002 EN/12 7. To install the CD changer (cars without an on-board monitor, without a DSP amplifier and with Professional radio SA663 after production date 03/01 only) 0 The installation of the power supply cable A for the CD change is only necessary, if the black 3-pin socket casing X18180 on the power supply for the CD changer is not tied back on the audio wiring harness. A X18180 F 39 1015 B 0 A1 30 X13016 Disconnect the black 12-pin plug connector X322 (30). Connect branch A2, white/grey/yellow cable on the power supply cable A, to slot PIN4. Press the contact socket out of plug connector X322 (30) and connect the twin-lead terminal to the 1-pin black socket casing (17). Screw the cable eyelet A1 to earth post X13016 under the left tail light. Lay the power supply cable A parallel to the standard wiring harness to the installation site of the CD changer. F 39 1016 B 0 A X325 30 oo o o oo ooooo oo Disconnect plug connector X325. Connect branch A3, red/green cable on the power supply cable A, to slot PIN1. To do this press the contact socket out of plug connector X325 and connect the twin-lead terminal to the 1-pin black socket casing (17). o ooo oo oo ooo o Lay branch A3, black 1-pin plug casing, along the wiring harness (30) on the boot floor from left to right to the tied back black 1-pin plug connector X325 and secure it. o oo ooo oooooo oo o F 39 1017 B 0 The installation of the control cable B for the CD changer is only required, if the black 6-pin socket casing X18729 on the control cable for the CD changer is not tied back on the audio wiring harness. B X18729 F 39 1018 B Retrofit / Installation kit No. 65 12 0 029 646 (others see cover sheet) Installation Instructions No. 01 29 0 029 575 Issue date: 05.2002 EN/13 7. To install the CD changer (cars without an on-board monitor, without a DSP amplifier and with Professional radio SA663 after production date 03/01 only) 0 B1 B1 E2 E2 2 B1 E2 F 39 1019 B Push the shrink hose (2) over branch E2, silver 10-pin plug casing on adapter cable E, and connect branch B1, silver 10-pin socket casing on control cable B to it. As you connect B1 to E2 ensure that it is correctly positioned, see figure. All sharp metal and plastic detents are to be removed from plug connection B1 and E2 using an angle cutter. There must be no sharp edges or corners on plug connection B1 and E2. Push the shrink hose (2) over the plug connection B1 and E2 and shrink it using a hot air blower. Retrofit / Installation kit No. 65 12 0 029 646 (others see cover sheet) Installation Instructions No. 01 29 0 029 575 Issue date: 05.2002 EN/14 7. To install the CD changer (cars without an on-board monitor, without a DSP amplifier and with Professional radio SA663 after production date 03/01 only) 0 30 31 32 33 35 Thread the adapter cable E and the control cable B from the radio (30) on the left under the centre console (31) between the gearbox tunnel (32) and carpet along the floor panel cross traverse (33). Lay the control cable B along the standard wiring harness near the sill (34) to the installation site of the CD changer (35) in the boot on the left. Secure the control cable B with cable ties. E B 34 F 39 1020 B 0 E1 30 Connect the white 12-pin socket casing E1 on adapter cable E to the new generation radio connection plug (30). Connect the new generation radio connection plug (30) and install the radio. E F 39 1021 B 0 The figure shows the boot at the rear left. Push the expanding nut (10) into the existing hole (30). 30 F 39 1022 B 10 0 11 Insert the base holder (8) and secure it with the hexagonal self-tapping screw (13) and two cap nuts M5 (11). 11 8 13 F 39 1023 B Retrofit / Installation kit No. 65 12 0 029 646 (others see cover sheet) Installation Instructions No. 01 29 0 029 575 Issue date: 05.2002 EN/15 7. To install the CD changer (cars without an on-board monitor, without a DSP amplifier and with Professional radio SA663 after production date 03/01 only) 0 30 V V H H 1 31 Remove the three transport guard screws (30) from the CD changer (1) and seal the apertures with the adhesive discs supplied (adhesive discs are supplied with the CD changer). Remove the two covers (31) and set the adjustment mechanism (32) with a straight slot screwdriver to V (vertical installation) and then reaffix both covers (31). 31 32 F 39 1024 B 0 A4/X18180 30 31 A 1 B Connect branch A4, black 3-pin socket casing on the power supply cable A or the standard power supply plug X18180 to the plug casing on the power supply connector (30) on the CD changer (1). Connect branch B2, black 6-pin socket casing on the control cable B or the standard plug X18729 to the plug casing (31) on the CD changer (1). B2/X18729 F 39 1025 B 0 12 12 18 1 30 8 9 Insert the CD changer (1) into the holder (9) and secure it with the four fillister head Philips screws (12). Secure the connection cable for the CD changer (1) with the holder (16) to the hole (31) from the inside. Place the CD changer (1) with the holder (9) on the base holder (8) and secure it with three collar nuts M5 (18). 16 F 39 1026 B Retrofit / Installation kit No. 65 12 0 029 646 (others see cover sheet) Installation Instructions No. 01 29 0 029 575 Issue date: 05.2002 EN/16 8. To install the CD changer (cars with an on-board monitor and without a DSP amplifier only) 0 The installation of the power supply cable A for the CD changer is only necessary, if the black 3-pin socket casing X18180 on the power supply for the CD changer is not tied back on the audio wiring harness. A X18180 F 39 1027 B 0 A1 30 X13016 Disconnect the black 12-pin plug connector X322 (30). Connect branch A2, white/grey/yellow cable on the power supply cable A, to slot PIN4. Press the contact socket out of plug connector X322 (30) and connect the twin-lead terminal to the 1-pin black socket casing (17). Screw the cable eyelet A1 to earth post X13016 under the left tail light. Lay the power supply cable A parallel to the standard wiring harness to the installation site of the CD changer. F 39 1028 B 0 A X325 30 oo o o oo ooooo oo o ooo oo oo ooo o Lay branch A3, black 1-pin plug casing, along the wiring harness (30) on the boot floor from left to right to the tied back black 1-pin plug connector X325 and secure it. Disconnect plug connector X325. Connect branch A3, red/green cable on the power supply cable A, to slot PIN1. To do this press the contact socket out of plug connector X325 and connect the twin-lead terminal to the 1-pin black socket casing (17). o oo ooo oooooo oo o F 39 1029 B 0 C The installation of the control cable C for the CD changer is only required, if the black 6-pin socket casing X18729 on the control cable for the CD changer is not tied back on the audio wiring harness. X18729 F 39 1030 B Retrofit / Installation kit No. 65 12 0 029 646 (others see cover sheet) Installation Instructions No. 01 29 0 029 575 Issue date: 05.2002 EN/17 8. To install the CD changer (cars with an on-board monitor and without a DSP amplifier only) 0 C1 C1 E2 E2 2 C1 E2 F 39 1031 B Push the shrink hose (2) over branch E2, silver 10-pin plug casing on adapter cable E, and connect branch C1, silver 10-pin socket casing on control cable C to it. As you connect C1 to E2 ensure that it is correctly positioned, see figure. All sharp metal and plastic detents are to be removed from plug connection C1 and E2 using an angle cutter. There must be no sharp edges or corners on plug connection C1 and E2. Push the shrink hose (2) over the plug connection C1 and E2 and shrink it using a hot air blower. Disconnect the new generation radio connection plug (30) from the on-board monitor radio (31). Connect the white 12-pin socket casing E1 on 30 adapter cable E to the new generation radio E1 connection plug (30). E Connect the new generation radio connection 31 31 plug and secure it. Lay the control cable C to the installation location 000 000 0 0 0 0 0 of the CD changer and secure it with cable ties parallel to the standard wiring harness. 0 0000 00 0 C 0 0000 00 0 0 0 0 0 0 0 00 0000000 0 F 39 1032 B 0 The figure shows the boot at the rear left. Push the expanding nut (10) into the existing hole (30). 30 10 F 39 1033 B Retrofit / Installation kit No. 65 12 0 029 646 (others see cover sheet) Installation Instructions No. 01 29 0 029 575 Issue date: 05.2002 EN/18 8. To install the CD changer (cars with an on-board monitor and without a DSP amplifier only) 0 Insert the base holder (8) and secure it with the hexagonal self-tapping screw (13) and two cap nuts M5 (11). 11 11 8 13 F 39 1034 B 0 30 V V H H Remove the three transport guard screws (30) from the CD changer (1) and seal the apertures with the adhesive discs supplied (adhesive discs are supplied with the CD changer). Remove the two covers (31) and set the adjustment mechanism (32) with a straight slot screwdriver to V (vertical installation) and then reaffix both covers (31). 1 31 31 32 F 39 1024 B 0 A4/X18180 30 31 A C Connect branch A4, black 3-pin socket casing on the power supply cable A or the standard power supply plug X18180 to the plug casing on the power supply connector (30) on the CD changer (1). Connect branch C2, black 6-pin socket casing on the control cable C or the standard plug X18729 to the plug casing (31) on the CD changer (1). 1 C2/X18729 F 39 1036 B 0 12 12 18 1 30 8 9 Insert the CD changer (1) into the holder (9) and secure it with the four fillister head Philips screws (12). Secure the connection cable for the CD changer (1) with the holder (16) to the hole (30) from the inside. Place the CD changer (1) with the holder (9) on the base holder (8) and secure it with three collar nuts M5 (18). 16 F 39 1026 B Retrofit / Installation kit No. 65 12 0 029 646 (others see cover sheet) Installation Instructions No. 01 29 0 029 575 Issue date: 05.2002 EN/19 9. To install the CD changer (cars with a DSP amplifier only) 0 Push the expanding nut (10) into the existing hole (30). 30 F 39 1022 B 10 0 Insert the base holder (8) and secure it with the hexagonal self-tapping screw (13) and two cap nuts M5 (11). 11 11 8 13 F 39 1023 B 0 30 V V H H Remove the three transport guard screws (30) from the CD changer (1) and seal the apertures with the adhesive discs supplied (adhesive discs are supplied with the CD changer). Remove the two covers (31) and set the adjustment mechanism (32) with a straight slot screwdriver to V (vertical installation) and then reaffix both covers (31). 1 31 31 32 F 39 1024 B 0 X18180 31 30 D2 Connect the power supply plug X18180 to the plug casing on the power supply connector (30) on the CD changer (1). Connect branch D2, straight plug on the coaxial cable D to the coaxial connector (31) on the CD changer (1). Secure the coaxial cable D with cable ties. D 1 F 39 1041 B Retrofit / Installation kit No. 65 12 0 029 646 (others see cover sheet) Installation Instructions No. 01 29 0 029 575 Issue date: 05.2002 EN/20 9. To install the CD changer (cars with a DSP amplifier only) 0 D D 31 D1 Connect branch D1, angled plug on the coaxial cable D on the coaxial connector (30) of the BMW Professional DSP amplifier hi-fi system (31). 31 30 F 39 1037 B Retrofit / Installation kit No. 65 12 0 029 646 (others see cover sheet) Installation Instructions No. 01 29 0 029 575 Issue date: 05.2002 EN/21 10. To install the CD changer (cars with CD changer preparation only) 0 Push the expanding nut (10) into the existing hole (30). 30 F 39 1022 B 10 0 Insert the base holder (8) and secure it with the hexagonal self-tapping screw (13) and two cap nuts M5 (11). 11 11 8 13 F 39 1023 B 0 30 V V H H Remove the three transport guard screws (30) from the CD changer (1) and seal the apertures with the adhesive discs supplied (adhesive discs are supplied with the CD changer). Remove the two covers (31) and set the adjustment mechanism (32) with a straight slot screwdriver to V (vertical installation) and then reaffix both covers (31). 1 31 31 32 F 39 1024 B 0 X18180 30 31 Connect the black 3-pin socket casing on the power supply plug X18180 to the plug casing on the power supply connector (30) on the CD changer (1). Connect the 6-pin socket casing, plug X18729, to the plug casing (31) on the CD changer (1). 1 X18729 F 39 1046 B Retrofit / Installation kit No. 65 12 0 029 646 (others see cover sheet) Installation Instructions No. 01 29 0 029 575 Issue date: 05.2002 EN/22 10. To install the CD changer (cars with CD changer preparation only) 0 12 12 18 1 30 8 9 Insert the CD changer (1) into the holder (9) and secure it with the four fillister head Philips screws (12). Secure the connection cable for the CD changer (1) with the holder (16) to the hole (30) from the inside. Place the CD changer (1) with the holder (9) on the base holder (8) and secure it with three collar nuts M5 (18). 16 F 39 1026 B Retrofit / Installation kit No. 65 12 0 029 646 (others see cover sheet) Installation Instructions No. 01 29 0 029 575 Issue date: 05.2002 EN/23 11. Coding and concluding work Coding This system cannot be diagnosed and requires no encoding. Concluding work Connect battery Conduct a function test Reassemble the car by following the instructions for its dismantling in reverse order Print out error memory Retrofit / Installation kit No. 65 12 0 029 646 (others see cover sheet) Installation Instructions No. 01 29 0 029 575 Issue date: 05.2002 EN/24 12. Function The function of the CD changer is described in the radio owner’s manual. Retrofit / Installation kit No. 65 12 0 029 646 (others see cover sheet) Installation Instructions No. 01 29 0 029 575 Issue date: 05.2002 EN/25 13. Circuit diagram X322 I-BUS X1* X325 4 X2* X3* 31 1 I-BUS 30<56 4,0 RTGN 0.5 WSGRGE 4,0 RTGN 0.5 RTGN 0.5 WSGRGE 0.5 BR X18180 3 2 I-BUS 30<56 1 31 N22 F 39 1043 B Retrofit / Installation kit No. 65 12 0 029 646 (others see cover sheet) Installation Instructions No. 01 29 0 029 575 Issue date: 05.2002 EN/26 13. Circuit diagram Legend N22 CD changer X1* Black 1-pin plug casing X2* Black 1-pin plug casing X3* cable eyelet 6 mm in diameter to X13016 under the left tail light X322 Black 12-pin plug connector, audio systems X325 Black 2-pin plug connector, audio systems X18180 Black 3-pin connection plug, CD changer The components and X designations marked with an asterisk (*) are only valid for this circuit diagram. All the other components and X designations correspond to BMW after-sales circuit diagrams Colour abbreviations BL = Blue BR = Brown GE = Yellow GN = Green GR = Grey OR = Orange RT = Red SW = Black VI = Violet WS = White 0 Retrofit / Installation kit No. 65 12 0 029 646 (others see cover sheet) Installation Instructions No. 01 29 0 029 575 Issue date: 05.2002 EN/27